Hearst Mining building clad in stone on the left, with extension on the right covered in shot peened aluminum alloy
Shot peening is a cold working process used to produce a compressiveresidual stress layer and modify the mechanical properties of metals and composites. It entails striking a surface with shot (round metallic, glass, or ceramic particles) with force sufficient to create plastic deformation.[1][2]
In machining, shot peening is used to strengthen and relieve stress in components like steel automobile crankshafts and connecting rods. In architecture it provides a muted finish to metal. Shot peening is similar mechanically to sandblasting, though its purpose is not to remove material, but rather it employs the mechanism of plasticity to achieve its goal, with each particle functioning as a ball-peen hammer.
Details
Peening a surface spreads it plastically, causing changes in the mechanical properties of the surface. Its main application is to avoid the propagation of microcracks in a surface. By putting a material under compressive stress, shot peening prevents such cracks from propagating.[3]
Shot peening is often called for in aircraft repairs to relieve tensile stresses built up in the grinding process and replace them with beneficial compressive stresses. Depending on the part geometry, part material, shot material, shot quality, shot intensity, and shot coverage, shot peening can increase fatigue life up to 1000%.[4][2]
Plastic deformation induces a residual compressive stress in a peened surface, along with tensile stress in the interior. Surface compressive stresses confer resistance to metal fatigue and to some forms of stress corrosion.[1] The tensile stresses deep in the part are not as troublesome as tensile stresses on the surface because cracks are less likely to start in the interior.
Intensity is a key parameter of the shot peening process. After some development of the process, an analog was needed to measure the effects of shot peening. John Almen noticed that shot peening made the side of the sheet metal that was exposed begin to bend and stretch. He created the Almen strip to measure the compressive stresses in the strip created by the shot peening operation. One can obtain what is referred to as the "intensity of the blast stream" by measuring the deformation on the Almen strip that is in the shot peening operation.[1] As the strip reaches a 10% deformation, the Almen strip is then hit with the same intensity for twice the amount of time. If the strip deforms another 10%, then one obtains the intensity of the blast stream.
Another operation to gauge the intensity of a shot peening process is the use of an Almen round, developed by R. Bosshard.
Coverage, the percentage of the surface indented once or more, is subject to variation due to the angle of the shot blast stream relative to the workpiece surface. The stream is cone-shaped, thus, shot arrives at varying angles. Processing the surface with a series of overlapping passes improves coverage, although variation in "stripes" will still be present. Alignment of the axis of the shot stream with the axis of the Almen strip is important. A continuous compressively stressed surface of the workpiece has been shown to be produced at less than 50% coverage but falls as 100% is approached. Optimizing coverage level for the process being performed is important for producing the desired surface effect.[5]
SAE International's[6] includes several standards for shot peening in aerospace and other industries.
Process and equipment
Popular methods for propelling shot media include air blast systems and centrifugal blast wheels. In the air blast systems, media are introduced by various methods into the path of high pressure air and accelerated through a nozzle directed at the part to be peened. The centrifugal blast wheel consists of a high speed paddle wheel. Shot media are introduced in the center of the spinning wheel and propelled by the centrifugal force by the spinning paddles towards the part by adjusting the media entrance location, effectively timing the release of the media. Other methods include ultrasonic peening, wet peening, and laser peening (which does not use media).
Media choices include spherical cast steel shot, ceramic bead, glass bead or conditioned (rounded) cut wire.[7] Cut wire shot is preferred because it maintains its roundness as it is degraded, unlike cast shot which tends to break up into sharp pieces that can damage the workpiece. Cut wire shot can last five times longer than cast shot. Because peening demands well-graded shot of consistent hardness, diameter, and shape, a mechanism for removing shot fragments throughout the process is desirable. Equipment is available that includes separators to clean and recondition shot and feeders to add new shot automatically to replace the damaged material.[8]
Wheel blast systems include satellite rotation models, rotary throughfeed components, and various manipulator designs. There are overhead monorail systems as well as reverse-belted models. Workpiece holding equipment includes rotating index tables, loading and unloading robots, and jigs that hold multiple workpieces. For larger workpieces, manipulators to reposition them to expose features to the shot blast stream are available.[8]
Cut wire shot
Cut wire shot is a metal shot used for shot peening,[2] where small particles are fired at a workpiece by a compressed air jet. It is a low-cost manufacturing process, as the basic feedstock is inexpensive. As-cut particles are an effective abrasive due to the sharp edges created in the cutting process; however, as-cut shot is not a desirable shot peening medium, as its sharp edges are not suitable to the process.
Cut shot is manufactured from high quality wire in which each particle is cut to a length about equal to its diameter. If required, the particles are conditioned (rounded) to remove the sharp corners produced during the cutting process. Depending on application, various hardness ranges are available, with the higher the hardness of the media the lower its durability.[clarification needed]
Factors affecting coverage density include: number of impacts (shot flow), exposure time, shot properties (size, chemistry), and work piece properties. Coverage is monitored by visual examination to determine the percent coverage (0-100%). Coverage beyond 100% cannot be determined. The number of individual impacts is linearly proportional to shot flow, exposure area, and exposure time. Coverage is not linearly proportional because of the random nature of the process (chaos theory). When 100% coverage is achieved, locations on the surface have been impacted multiple times. At 150% coverage, 5 or more impacts occur at 52% of locations. At 200% coverage, 5 or more impacts occur at 84% of locations.
Coverage is affected by shot geometry and the shot and workpiece chemistry. The size of the shot controls how many impacts there are per pound, where smaller shot produces more impacts per pound therefore requiring less exposure time. Soft shot impacting hard material will take more exposure time to reach acceptable coverage compared to hard shot impacting a soft material (since the harder shot can penetrate deeper, thus creating a larger impression).
Coverage and intensity (measured by Almen strips) can have a profound effect on fatigue life. This can affect a variety of materials typically shot peened. Incomplete or excessive coverage and intensity can result in reduced fatigue life. Over-peening will cause excessive cold working on the surface of the workpiece, which can also cause fatigue cracks.[8] Diligence is required when developing parameters for coverage and intensity, especially when using materials having different properties (i.e. softer metal to harder metal). Testing fatigue life over a range of parameters would result in a "sweet-spot" where there is near exponential growth to a peak fatigue life (x = peening intensity or media stream energy, y = time-to-crack or fatigue strength) and rapidly decay fatigue life as more intensity or coverage is added. The "sweet-spot" will directly correlate with the kinetic energy transferred and the material properties of the shot media and workpiece.
Applications
Shot peening is used on gear parts, cams and camshafts, clutch springs, coil springs, connecting rods, crankshafts, gearwheels, leaf and suspension springs, rock drills, and turbine blades.[2] It is also used in foundries for sand removal, decoring, descaling, and surface finishing of castings such as engine blocks and cylinder heads. Its descaling action can be used in the manufacturing of steel products such as strip, plates, sheets, wire, and bar stock.[1][8]
Shot peening is a crucial process in spring making. Types of springs include leaf springs, extension springs, and compression springs. The most widely used application are for engine valve springs (compression springs) due to high cyclic fatigue. In an OEM valve spring application, the mechanical design combined with some shot peening ensures longevity. Automotive makers are shifting to more high performance higher stressed valve spring designs as engines evolve. In aftermarket high performance valve spring applications, the need for controlled and multi-step shot peening is a requirement to withstand extreme surface stresses that sometimes exceeds material specifications. The fatigue life of an extreme performance spring (NHRA, IHRA) can be as short as two passes on a 1/4 mile drag racing track before relaxation or failure occurs.
Shot peening may be used for cosmetic effect. The surface roughness resulting from the overlapping dimples causes light to scatter upon reflection. Because peening typically produces larger surface features than sand-blasting, the resulting effect is more pronounced.
Shot peening and abrasive blasting can apply materials on metal surfaces. When the shot or grit particles are blasted through a powder or liquid containing the desired surface coating, the impact plates or coats the workpiece surface. The process has been used to embed ceramic coatings, though the coverage is random rather than coherent. 3M developed a process where a metal surface was blasted with particles with a core of alumina and an outer layer of silica. The result was fusion of the silica to the surface. The process known as peen plating was developed by NASA. Fine powders of metals or non-metals are plated onto metal surfaces using glass bead shot as the blast medium. The process has evolved to applying solid lubricants such as molybdenum disulphide to surfaces. Biocompatible ceramics have been applied this way to biomedical implants. Peen plating subjects the coating material to high heat in the collisions with the shot and the coating must also be available in powder form, limiting the range of materials that can be used. To overcome the problem of heat, a process called temperature moderated-collision mediated coating (TM-CMC) has allowed the use of polymers and antibiotic materials as peened coatings. The coating is presented as an aerosol directed to the surface at the same time as a stream of shot particles. The TM-CMC process is still in the R&D phase of development.[9]
Compressive residual stress
A sub-surface compressive residual stress profile is measured using techniques such as x-ray diffraction and hardness profile testings. The X-axis is depth in mm or inches and the Y-axis is residual stress in ksi or MPa. The maximum residual stress profile can be affected by the factors of shot peening, including: part geometry, part material, shot material, shot quality, shot intensity, and shot coverage. For example, shot peening a hardened steel part with a process and then using the same process for another unhardened part could result in over-peening; causing a sharp decrease in surface residual stresses, but not affecting sub-surface stresses. This is critical because maximum stresses are typically at the surface of the material. Mitigation of these lower surface stresses can be accomplished by a multi-stage post process with varied shot diameters and other surface treatments that remove the low residual stress layer.
The compressive residual stress in a metal alloy is produced by the transfer of kinetic energy (K.E.) from a moving mass (shot particle or ball peen) into the surface of a material with the capacity to plastically deform. The residual stress profile is also dependent on coverage density. The mechanics of the collisions involve properties of the shot hardness, shape, and structure; as well as the properties of the workpiece. Factors for process development and the control for K.E. transfer for shot peening are: shot velocity (wheel speed or air pressure/nozzle design), shot mass, shot chemistry, impact angle and work piece properties. Example: if you needed very high residual stresses you would likely want to use large diameter cut-wire shot, a high-intensity process, direct blast onto the workpiece, and a very hard workpiece material.
See also
Autofrettage, which produces compressive residual stresses in pressure vessels.
Metallurgy is a domain of materials science and engineering that studies the physical and chemical behavior of metallic elements, their inter-metallic compounds, and their mixtures, which are known as alloys. Metallurgy encompasses both the science and the technology of metals; that is, the way in which science is applied to the production of metals, and the engineering of metal components used in products for both consumers and manufacturers. Metallurgy is distinct from the craft of metalworking. Metalworking relies on metallurgy in a similar manner to how medicine relies on medical science for technical advancement. A specialist practitioner of metallurgy is known as a metallurgist.
An abrasive is a material, often a mineral, that is used to shape or finish a workpiece through rubbing which leads to part of the workpiece being worn away by friction. While finishing a material often means polishing it to gain a smooth, reflective surface, the process can also involve roughening as in satin, matte or beaded finishes. In short, the ceramics which are used to cut, grind and polish other softer materials are known as abrasives.
In materials science and solid mechanics, residual stresses are stresses that remain in a solid material after the original cause of the stresses has been removed. Residual stress may be desirable or undesirable. For example, laser peening imparts deep beneficial compressive residual stresses into metal components such as turbine engine fan blades, and it is used in toughened glass to allow for large, thin, crack- and scratch-resistant glass displays on smartphones. However, unintended residual stress in a designed structure may cause it to fail prematurely.
Surface finishing is a broad range of industrial processes that alter the surface of a manufactured item to achieve a certain property. Finishing processes may be employed to: improve appearance, adhesion or wettability, solderability, corrosion resistance, tarnish resistance, chemical resistance, wear resistance, hardness, modify electrical conductivity, remove burrs and other surface flaws, and control the surface friction. In limited cases some of these techniques can be used to restore original dimensions to salvage or repair an item. An unfinished surface is often called mill finish.
Carbonitriding is a metallurgical surface modification technique that is used to increase the surface hardness of a metal, thereby reducing wear.
Induction hardening is a type of surface hardening in which a metal part is induction-heated and then quenched. The quenched metal undergoes a martensitic transformation, increasing the hardness and brittleness of the part. Induction hardening is used to selectively harden areas of a part or assembly without affecting the properties of the part as a whole.
An Almen strip is a thin strip of SAE 1070 steel used to quantify the intensity of a shot peening process.
Laser peening (LP), or laser shock peening (LSP), is a surface engineering process used to impart beneficial residual stresses in materials. The deep, high-magnitude compressive residual stresses induced by laser peening increase the resistance of materials to surface-related failures, such as fatigue, fretting fatigue and stress corrosion cracking. Laser shock peening can also be used to strengthen thin sections, harden surfaces, shape or straighten parts, break up hard materials, compact powdered metals and for other applications where high pressure, short duration shock waves offer desirable processing results.
Sandblasting, sometimes known as abrasive blasting, is the operation of forcibly propelling a stream of abrasive material against a surface under high pressure to smooth a rough surface, roughen a smooth surface, shape a surface or remove surface contaminants. A pressurised fluid, typically compressed air, or a centrifugal wheel is used to propel the blasting material. The first abrasive blasting process was patented by Benjamin Chew Tilghman on 18 October 1870.
Low plasticity burnishing (LPB) is a method of metal improvement that provides deep, stable surface compressive residual stresses with little cold work for improved damage tolerance and metal fatigue life extension. Improved fretting fatigue and stress corrosion performance has been documented, even at elevated temperatures where the compression from other metal improvement processes relax. The resulting deep layer of compressive residual stress has also been shown to improve high cycle fatigue (HCF) and low cycle fatigue (LCF) performance.
Mechanical plating, also known as peen plating, mechanical deposition, or impact plating, is a plating process that imparts the coating by cold welding fine metal particles to a workpiece. Mechanical galvanization is the same process, but applies to coatings that are thicker than 0.001 in (0.025 mm). It is commonly used to overcome hydrogen embrittlement problems. Commonly plated workpieces include nails, screws, nuts, washers, stampings, springs, clips, and sintered iron components.
Electrochemical grinding is a process that removes electrically conductive material by grinding with a negatively charged abrasive grinding wheel, an electrolyte fluid, and a positively charged workpiece. Materials removed from the workpiece stay in the electrolyte fluid. Electrochemical grinding is similar to electrochemical machining but uses a wheel instead of a tool shaped like the contour of the workpiece.
Surface integrity is the surface condition of a workpiece after being modified by a manufacturing process. The term was coined by Michael Field and John F. Kahles in 1964.
Steel abrasives are steel particles that are used as abrasive or peening media. They are usually available in two different shapes that address different industrial applications.
Metal Improvement Company LLC (MIC), a business unit of the Surface Technologies Division of Curtiss-Wright Corporation, is a company specializing in metal surface treatments.
The high-frequency impact treatment or HiFIT – Method is the treatment of welded steel constructions at the weld transition to increase the fatigue strength.
An Almen round is a thin round disk used to quantify the intensity of a shot peening process. Developed in 1994 by Rudolf Bosshard in Switzerland, it is a modification of the Almen strip method, which is used worldwide as a surface treatment testing method in the field of shot peening. The basic principle is the same, but due to the simple shape and minimized size, the Almen round is more suitable for automated processing and installation on dummy rigs. Also instead of the Almen block according SAE J442, here a matching device is used and if connected to electronic processing unit, the Almen value according AMS-S-13165 can be evaluated in one run.
Shot peening can be used as a method for reconditioning distorted steel conveyor belts. The shot peening process is quick and cost-effective. Compared with other methods the shot peening is lower cost and does not interrupt daily production. A deformed steel belt has the following disadvantages:
In metallurgy, peening is the process of working a metal's surface to improve its material properties, usually by mechanical means, such as hammer blows, by blasting with shot, or focusing light. Peening is normally a cold work process, with laser peening being a notable exception. It tends to expand the surface of the cold metal, thereby inducing compressive stresses or relieving tensile stresses already present. Peening can also encourage strain hardening of the surface metal.
Ice blasting is a form of non-abrasive blasting where frozen water particles are combined with compressed air and propelled towards a surface for cleaning purposes. Ice is one of several different medias commonly used for blast cleaning. Another common method of non-abrasive blasting is dry ice blasting, which uses the solid form of CO2 as a blast media. Forms of abrasive blasting use mediums such as sand, plastic beads, and baking soda.
References
1 2 3 4 "Shot Peening," Tool and Manufacturing Engineers Handbook (TMEH), Volume 3, Society of Manufacturing Engineers, 1985
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
