Slickline

Last updated

Slickline refers to a single strand wire which is used to run a variety of tools down into the wellbore for several purposes. It is used during well drilling operations in the oil and gas industry. In general, it can also describe a niche of the industry that involves using a slickline truck or doing a slickline job. Slickline looks like a long, smooth, unbraided wire, often shiny, silver/chrome in appearance. It comes in varying lengths, according to the depth of wells in the area it is used (it can be ordered to specification) up to 35,000 feet in length. It is used to lower and raise downhole tools used in oil and gas well maintenance to the appropriate depth of the drilled well.

Contents

In use and appearance it is connected by a drum as it is spooled off the back of the slickline truck to the wireline sheave, a round wheel grooved and sized to accept a specified line and positioned to redirect the line to another sheave that will allow the slickline to enter the wellbore. [1] Slickline is used to lower downhole tools into an oil or gas well to perform a specified maintenance job downhole. Downhole refers to the area in the pipe below surface, the pipe being either the casing cemented in the hole by the drilling rig (which keeps the drilled hole from caving in and pressure from the various oil or gas zones downhole from feeding into one another) or the tubing, a smaller diameter pipe hung inside the casing.

Uses

Slickline is more commonly used in production tubing. The wireline operator monitors at surface the slickline tension via a weight indicator gauge and the depth via a depth counter 'zeroed' from surface, lowers the downhole tool to the proper depth, completes the job by manipulating the downhole tool mechanically, checks to make sure it worked if possible, and pulls the tool back out by winding the slickline back onto the drum it was spooled from. The slickline drum is controlled by a hydraulic pump, which in turn is controlled by the 'slickline operator'

Slickline comes in different sizes and grades. The larger the size, and higher the grade, generally means the higher line tension can be pulled before the line snaps at the weakest spot and causes a costly 'fishing' job. Due to downhole tools getting stuck because of malfunctions or 'downhole conditions' including sand, scale, salt, asphaltenes, and other well byproducts settling or loosening off the pipe walls because of agitation either by the downhole tools or a change in downhole inflow, sometimes it is necessary to pull hard on the tools to bring them back uphole to surface. If the tools are stuck, and the operator pulls too hard, the line will snap or pull apart at the weakest spot, which is generally closer to surface as the further uphole the weak point in the line is, the more weight it has to support (the weight of the line).

Weak spots in the line can be caused by making the circle around the counter wheel, making a bend around a sheave, a kink in a line from normal use (when rigging up the equipment extra line must be pulled out from the truck to give enough slack when the pressure control lubricator is picked up – this leaves line coiled on the often rutted ground, and sometimes it snags and kinks the line).

When the slickline parts, this can create an expensive 'fishing' job. It is called fishing because you often have to try different 'fishing' tools until you get a 'bite', then you have to work the original tools downhole free, or cut off the slickline where they join the tools downhole so that you can pull the broken slickline back to surface and out of the way, in order to fish the stuck toolstring. Because of the downtime involved in 'fishing', meaning not being able to flow the oil/gas well, the client is losing money by lack of production and also the cost of the slickline unit to fish, and the cost of what is left in the hole if it is not fished out (in the oil/gas industry, if the cause of the fishing job was not the fault of the slickline company, the oil/gas company is usually responsible to pay for it, and it can be very expensive).

Slickline was originally called measuring line, because the line was flat like a tape measure, and marked with depth increments so the operators would know how deep in the hole they were. This probably changed because the flat measuring line wasn't as strong as the modern slickline, and separate depth counters were developed. It is advantageous to keep the diameter of the wire as small as possible for the following reasons:

The disadvantage of a smaller-diameter slickline is the lower strength. Depth and the nature of the job (a tool that must be pulled hard or might be stuck) will affect what slickline truck (different trucks specialize in different sizes of line) used.

The sizes of solid wireline in most common uses are: 0.092", 0.108", 0.125", 0.140", 0.150", and 0.160" in diameter, and are obtainable from the wire-drawing mills in one-piece standard lengths of 18,000, 20,000, 25,000 and 30,000 foot lengths. Other diameters and lengths are usually available on request from the suppliers, with the largest size currently available at 0.188".

Mechanical and Hydraulic Jars

Slickline tools operate with a mechanical action, controlled from surface in the wireline trucks operators compartment. Typically, this mechanical action is accomplished by the operation of jars. There are generally two types of jars; mechanical and hydraulic.

Mechanical jars look like a long, tubular piece of machined metal that slides longer or shorter approximately 75% to 90% of its total length. They give the effect of hammering on the downhole tools. The weight or hit of the 'hammer' depends on how much sinker bar is added above the jars. Generally, a slickline operator controls the downhole tools with taps and hits from the sinker bar via the mechanical jars, controlled at surface by lowering or raising the toolstring and monitoring weight, depth, and pressure. Mechanical jars for slickline can hit up or down the hole, making them a versatile form of jarring.

Hydraulic jars for slickline are generally meant to jar up only, because not enough sinker bar is able to feasibly be lubricated in to jar down on the downhole tools. Hydraulic jars work by the operator pulling up on the line, which puts an upward force on the top of the hydraulic jars. The bottom of the hydraulic jars is usually attached by threaded connection to the mechanical jars, which are attached to the downhole tools. Depending on how hard the operator pulls on the hydraulic jars will affect how fast they hit, and how hard they hit. When the top is pulled on, the inner mandrel begins to slide upwards. It has a restriction in it that hydraulic fluid has to bypass as it is pulled upwards, until it reaches an area of no restriction, allowing it to slide rapidly. The reason for the initial tighter restriction is to allow the operator to pull his line to the desired hitting range.

Generally once he hits that range on his weight indicator, he waits while the jars open to the less restricted point, whereupon the sinker bar travels upwards rapidly, providing an upwards hit on the downhole tools. The jars can then be 'reset' by lowering the line until the weight of the sinker bar closes, or pushes the inner mandrel of the hydraulic jars back to the starting position. Because the hydraulic jars are designed to provide a wait time to allow the operator to get up to the desired line tension, they can provide a very effective upwards hit.

Mechanical jar and hydraulic jar hitting power is affected by the length of the jars (the longer the length, they faster they can travel before they stop), the mass of the weight above them (the more the mass, the harder they will hit), and the tension of the line pulling on them.

Some completion components may be deployed and retrieved on slickline such as wireline retrievable safety valves, battery powered downhole gauges, perforating, placing explosively set bridge plugs, and placing or retrieving gas lift valves. Slickline can also be used for fishing, the process of trying to retrieve other equipment and wire, which has been dropped down the hole.

Applications

The most common applications for slickline are:

Braided line

Braided line is generally used when the strength of slickline is insufficient for the task. Most commonly, this is for heavy fishing such as retrieving broken drill pipe.

Slickline tools

Jar

This type of tool can be extended and closed rapidly to induce a mechanical shock to the tool string. This shock can induce certain components such as plugs to lock into place and then unlock for retrieving. Jars are commonly used to shear small brass or steel pins that are put in place to function certain down-hole tools at a certain moment. The operator can use the jars to shear the pins at a predetermined depth. Spang jars are manually operated by the wireline operator, who either lifts or lowers wire rapidly, requiring a great deal of expertise.

Stem

Stem essentially just serves to add weight to the toolstring. The weight may be necessary to overcome the pressure of the well. Some variations of stem, called roller stem, may have wheels built into the tool to allow the tool string to glide more easily down moderately deviated wells. Stem give the hammering action to the tool string which in turn allows the jars to transmit the force given by the movement of the stem's bars. Depending on well conditions, either extra-small OD stems are used or extra-large. The range can be from .75" to 3.50" OD and the stems normally come in 2 ft, 3 ft or 5 ft lengths. The connection to the rope socket or other tools can be a threaded connection or a QLS system (quick connect).

Pulling tools

These are tools designed for fishing other wireline components which have been dropped or placed in the well down hole. All wireline tools are designed with 'fishing necks' on their top side, intended to be easily grabbed by pulling tools with a matching 'ID' to that of the 'OD' of the fishing neck. Pulling tools are also used for retrieving seated components such as plug prongs. Almost all pulling tools are equipped with a safety feature (shear pin) so they may release a stuck tool and allow the tool string to be brought to the surface for changes in components (hydraulic jars for example).

Gauge cutter (gauge ring)

A gauge cutter is a tool with a round, open-ended bottom which is milled to an accurate size. Large openings above the bottom of the tool allow for fluid bypass while running in the hole. Most often a gauge ring will be the first tool run on a slickline operation. A gauge ring that is just undersized will allow the operator to ensure clear tubing down to the deepest projected working depth; for example 2 7/8" tubing containing 2.313" profiles would call for a gauge ring between 2.25" and 2.30". A gauge ring can also be used to remove light paraffin that may have built up in the tubing. Often a variety of different-sized gauges and/or scratchers will be run to remove paraffin little by little. Gauge cutter can be used for drift runs also.

Lead impression block

If an obstruction is found downhole, a lead impression block can be run to help determine its nature. The LIB has a malleable lead base in which the obstruction can leave an impression when they meet. The LIB is called Wireline Camera because of its function to mark any object downhole. They are also sometimes called "confusion" blocks because they only give a two-dimensional view of the down-hole object, making it hard for an inexperienced person to determine what three-dimensional object is in the hole

Downhole bailer

Bailers are downhole tools that are generally long and tubular shaped, and are used for both getting samples of downhole solids (sand, scale, asphaltenes, rust, rubber and debris from well servicing operations) and for 'bailing' the unwanted downhole solids from the well. Bailers are attached either via threaded connection or releasable downhole tool to the wireline toolstring, and are manipulated from surface by the wireline operator. Bailers usually have an interchangeable bottom (the shoe) which also houses a check to keep the solids from falling or washing out of the bottom.

Sample bailer

A sample bailer is a hollow tube (the barrel), generally around a meter long, around 40 mm in diameter, with a 'ball check' – a form of non-return valve – on the bottom and an opening at the top. This tool is beat downwards into the obstruction using the mechanical jars and weight above of the wireline toolstring. Generally, after a number of 'hits', hopefully allowing a usable sample of solids to enter the barrel, the tool is pulled upwards, and the sample in the barrel should settle the ball check onto its seat, which will keep the solids in the barrel during the return trip to surface, where the sample can be inspected to determine the composition of the obstruction. The success of this depends on how readily the solid was accepted into the barrel, and if the ball check was properly seated on the return trip to surface. If the ball check is not seated (sometimes a large, hard piece of solid will sit in between the ball and seat) downhole fluids tend to wash the sample out of the bottom of the sample bailer, leaving the inspectors at surface uncertain whether the tool actually collected a sample. The procedure may have to be repeated until a sample is successfully retrieved.

Stroke bailer

A stroke bailer functions like a 'Chinese water pump', and is used to collect unwanted solids from the wellbore. A stroke bailer is long and tubular looking, with a smaller rod that extends from the top, a hole in the bottom, and is generally around 7 meters long, but the length depends on how much barrel section is added to the bailer. The barrel 'free floats' on the stroke rod, which is attached to the wireline toolstring. The tool is usually 'spudded' into the downhole solid, then the wireline toolstring is pulled upwards, which in turn pulls the stroke up through the barrel. Ideally, this draws the downhole solid in through the bottom 'shoe' of the tool, past the check and into the barrel for collection. The tool is usually stroked either a predetermined number of times, or until it appears the tool is not stroking, which can mean either it is full, or stuck.

Hydrostatic bailer

A hydrostatic bailer functions like a 'vacuum', and is used to suck up unwanted solids from the wellbore. A hydrostatic bailer is generally around 2.5 meters long and is tubular looking, with two 10 mm holes on opposing sides at the top of the tool, and a hole in the bottom. A hydrostatic bailer uses a pinned plug with o-ring seals at the bottom, and a plug at the top to maintain the surface pressure that it was assembled at (nominally around 100 kPa) all the way to the bottom of the well, whereupon it is spudded into the downhole solids, which ideally pushes the shoe into the bottom plug, which shears the pin on the bottom plug. An oil or gas well's pressure downhole is always more than atmospheric pressure at surface, due to the formation pressure, and a combination of depth and hydrostatic weight of wellbore fluids. Sometimes fluid will be added to the wellbore to assist in bailing by bringing up the pressure, and also lubricating the downhole solid. Because the pressure inside the bailer is much less than the downhole wellbore pressure, any solids that are loose enough are 'sucked up' by the vacuum formed when the bottom plug is sheared and travels upwards through the barrel, followed by the solids. At the same time, due to the changed from negative pressure to positive pressure, the top plug pops out (and is caught by the top part of the tool), and excess flow is directed out through the 10 mm ports on the sides of the top of the tool. These ports allow the barrel to fill more readily. Then the bailer is returned to surface where it is taken apart, the solids are emptied, and it is cleaned and serviced with new o-ring seals. Care must be taken when disassembling at surface as the tool is potentially charged with the downhole pressure (possibly many tens of thousands of kpa) and may 'blow apart' when being unthreaded if not bled off first.

Running tools

These tools are primarily used to 'set' plugs into locking profiles (nipples) located in the tubing; however, the term 'running tool' refers to a downhole tool attached to the wireline toolstring that is used to 'run' another tool that is meant to be left downhole when the toolstring returns to surface. In general, a running tool is attached to a downhole 'locking tool' that locates and locks into the selected downhole profile (nipple). The 'locking tool', or 'lock' for short, can be attached via threaded connection to the top of a variety of different tools, including but not limited to, downhole chokes (flow rate restrictors sized according to a pre-determined calculation), one-way check valves (TKX style plugs), instrument hangers, and most commonly, tubing plugs. The lock is fitted onto the running tool and attached using shear pins made of brass or steel. When the target profile is reached the lock can be set by seating the lock into the profile using mechanical jars (spangs) until the locking keys have locked the lock into the profile, whereupon the operator usually 'pull tests' the lock to give an indication it is properly 'set', then shears off the shear pins with his mechanical or hydraulic jars to allow the 'toolstring' to return to surface. There are many different types of running tools; some are mechanically complex and able to be made 'selective' in order to pass through profiles in order to reach one of the same size but a different depth; some are relatively simple, such as an 'F' collarstop running tool, which is essentially a metal rod which fits inside the collarstop downhole tool which is pinned in place.

Related Research Articles

<span class="mw-page-title-main">Wireline (cabling)</span> Technology used in oil and gas wells

In the oil and gas industry, the term wireline usually refers to the use of multi-conductor, single conductor or slickline cable, or "wireline", as a conveyance for the acquisition of subsurface petrophysical and geophysical data and the delivery of well construction services such as pipe recovery, perforating, plug setting and well cleaning and fishing. The subsurface geophysical and petrophysical information results in the description and analysis of subsurface geology, reservoir properties and production characteristics.

<span class="mw-page-title-main">Drill string</span> Drill pipe that transmits drilling fluid

A drill string on a drilling rig is a column, or string, of drill pipe that transmits drilling fluid and torque to the drill bit. The term is loosely applied to the assembled collection of the smuggler pool, drill collars, tools and drill bit. The drill string is hollow so that drilling fluid can be pumped down through it and circulated back up the annulus.

<span class="mw-page-title-main">Directional drilling</span> Practice of drilling non-vertical bores

Directional drilling is the practice of drilling non-vertical bores. It can be broken down into four main groups: oilfield directional drilling, utility installation directional drilling, directional boring, and surface in seam (SIS), which horizontally intersects a vertical bore target to extract coal bed methane.

Well logging, also known as borehole logging is the practice of making a detailed record of the geologic formations penetrated by a borehole. The log may be based either on visual inspection of samples brought to the surface or on physical measurements made by instruments lowered into the hole. Some types of geophysical well logs can be done during any phase of a well's history: drilling, completing, producing, or abandoning. Well logging is performed in boreholes drilled for the oil and gas, groundwater, mineral and geothermal exploration, as well as part of environmental and geotechnical studies.

A drilling rig is used to create a borehole or well in the earth's sub-surface, for example in order to extract natural resources such as gas or oil. During such drilling, data is acquired from the drilling rig sensors for a range of purposes such as: decision-support to monitor and manage the smooth operation of drilling; to make detailed records of the geologic formations penetrated by a borehole; to generate operations statistics and performance benchmarks such that improvements can be identified, and to provide well planners with accurate historical operations-performance data with which to perform statistical risk analysis for future well operations. The terms measurement while drilling (MWD), and logging while drilling (LWD) are not used consistently throughout the industry. Although these terms are related, within the context of this section, the term measurement while drilling refers to directional-drilling measurements, e.g. for decision support for the wellbore path, while LWD refers to measurements concerning the geological formations penetrated while drilling.

<span class="mw-page-title-main">Blowout preventer</span> Specialized valve

A blowout preventer (BOP) is a specialized valve or similar mechanical device, used to seal, control and monitor oil and gas wells to prevent blowouts, the uncontrolled release of crude oil or natural gas from a well. They are usually installed in stacks of other valves.

<span class="mw-page-title-main">Drill stem test</span>

A drill stem test (DST) is a procedure for isolating and testing the pressure, permeability and productive capacity of a geological formation during the drilling of a well. The test is an important measurement of pressure behaviour at the drill stem and is a valuable way of obtaining information on the formation fluid and establishing whether a well has found a commercial hydrocarbon reservoir.

Artificial lift refers to the use of artificial means to increase the flow of liquids, such as crude oil or water, from a production well. Generally this is achieved by the use of a mechanical device inside the well or by decreasing the weight of the hydrostatic column by injecting gas into the liquid some distance down the well. A newer method called Continuous Belt Transportation (CBT) uses an oil absorbing belt to extract from marginal and idle wells. Artificial lift is needed in wells when there is insufficient pressure in the reservoir to lift the produced fluids to the surface, but often used in naturally flowing wells to increase the flow rate above what would flow naturally. The produced fluid can be oil, water or a mix of oil and water, typically mixed with some amount of gas.

Underbalanced drilling, or UBD, is a procedure used to drill oil and gas wells where the pressure in the wellbore is kept lower than the static pressure of the formation being drilled. As the well is being drilled, formation fluid flows into the wellbore and up to the surface. This is the opposite of the usual situation, where the wellbore is kept at a pressure above the formation to prevent formation fluid entering the well. In such a conventional "overbalanced" well, the invasion of fluid is considered a kick, and if the well is not shut-in it can lead to a blowout, a dangerous situation. In underbalanced drilling, however, there is a "rotating head" at the surface - essentially a seal that diverts produced fluids to a separator while allowing the drill string to continue rotating.

<span class="mw-page-title-main">Coiled tubing</span> Long metal pipe used in oil and gas wells

In the oil and gas industry, coiled tubing refers to a long metal pipe, normally 1 to 3.25 in in diameter which is supplied spooled on a large reel. It is used for interventions in oil and gas wells and sometimes as production tubing in depleted gas wells. Coiled tubing is often used to carry out operations similar to wirelining. The main benefits over wireline are the ability to pump chemicals through the coil and the ability to push it into the hole rather than relying on gravity. Pumping can be fairly self-contained, almost a closed system, since the tube is continuous instead of jointed pipe. For offshore operations, the 'footprint' for a coiled tubing operation is generally larger than a wireline spread, which can limit the number of installations where coiled tubing can be performed and make the operation more costly. A coiled tubing operation is normally performed through the drilling derrick on the oil platform, which is used to support the surface equipment, although on platforms with no drilling facilities a self-supporting tower can be used instead. For coiled tubing operations on sub-sea wells a mobile offshore drilling unit (MODU) e.g. semi-submersible, drillship etc. has to be utilized to support all the surface equipment and personnel, whereas wireline can be carried out from a smaller and cheaper intervention vessel. Onshore, they can be run using smaller service rigs, and for light operations a mobile self-contained coiled tubing rig can be used.

<span class="mw-page-title-main">Well intervention</span> Operation on a deteriorating oil well

A well intervention, or well work, is any operation carried out on an oil or gas well during, or at the end of, its productive life that alters the state of the well or well geometry, provides well diagnostics, or manages the production of the well.

A production packer is a standard component of the completion hardware of oil or gas wells used to provide a seal between the outside of the production tubing and the inside of the casing, liner, or wellbore wall.

A downhole safety valve refers to a component on an oil and gas well, which acts as a failsafe to prevent the uncontrolled release of reservoir fluids in the event of a worst-case-scenario surface disaster. It is almost always installed as a vital component on the completion.

<span class="mw-page-title-main">Snubbing</span> Type of heavy well intervention performed on oil and gas wells

Snubbing is a type of heavy well intervention performed on oil and gas wells. It involves running the BHA on a pipe string using a hydraulic workover rig. Unlike wireline or coiled tubing, the pipe is not spooled off a drum but made up and broken up while running in and pulling out, much like conventional drill pipe. Due to the large rigup, it is only used for the most demanding of operations when lighter intervention techniques do not offer the strength and durability. The first snubbing unit was primarily designed to work in well control situations to "snub" drill pipe and or casing into, or out of, a well bore when conventional well killing methods could not be used. Unlike conventional drilling and completions operations, snubbing can be performed with the well still under pressure. When done so, it is called hydraulic workover. It can also be performed without having to remove the Christmas tree from the wellhead.

<span class="mw-page-title-main">Completion (oil and gas wells)</span> Last operation for oil and gas wells

Well completion is the process of making a well ready for production after drilling operations. This principally involves preparing the bottom of the hole to the required specifications, running in the production tubing and its associated down hole tools as well as perforating and stimulating as required. Sometimes, the process of running in and cementing the casing is also included. After a well has been drilled, should the drilling fluids be removed, the well would eventually close in upon itself. Casing ensures that this will not happen while also protecting the wellstream from outside incumbents, like water or sand.

A sliding sleeve is a standard component for the completion of an oil or gas well. Their main uses are to shut off flow from one or more reservoir zones or to regulate pressure between zones.

Oilfield terminology refers to the jargon used by those working in fields within and related to the upstream segment of the petroleum industry. It includes words and phrases describing professions, equipment, and procedures specific to the industry. It may also include slang terms used by oilfield workers to describe the same.

<span class="mw-page-title-main">Tripping (pipe)</span>

Tripping pipe is the physical act of pulling the drill string out of the wellbore and then running it back in. This is done by physically breaking out or disconnecting every other 2 or 3 joints of drill pipe at a time and racking them vertically in the derrick. When feasible the driller will start each successive trip on a different "break" so that after several trips fresh pipe dope will have been applied to every segment of the drill string.

<span class="mw-page-title-main">Pipe recovery operations</span>

Pipe recovery is a specific wireline operation used in the oil and gas industry, when the drill string becomes stuck downhole. Stuck pipe prevents the drill rig from continuing operations. This results in costly downtime, ranging anywhere from $10,000-1,000,000 per day of downtime, therefore it is critical to resolve the problem as quickly as possible. Pipe recovery is the process by which the location of the stuck pipe is identified, and the free pipe is separated from the stuck pipe either by a backoff or a chemical cut. This allows fishing tools to subsequently be run down hole to latch onto and remove the stuck pipe.

References

  1. "Sheave". Archived from the original on 2016-03-31.