UNIVAC 1050

Last updated
Block diagram of a UNIVAC 1050 U1050-ref1962 PD.png
Block diagram of a UNIVAC 1050

The UNIVAC 1050 was a variable word-length (one to 16 characters) decimal and binary computer. It was initially announced in May 1962 as an off-line input-output processor for larger UNIVAC systems. [1]

Instructions were fixed length (30 bits five characters), consisting of a five-bit "op code", a three-bit index register specifier, one reserved bit, a 15-bit address, and a six-bit "detail field" whose function varies with each instruction. The memory was up to 32K of six-bit characters.

The first 256 memory positions were group into 64 fields of 4 characters each, called "tetrads", [1] it is possible to address any of these positions either by tetrad or by individual character. These Tetrads were used to implement the following:

Like the IBM 1401, the 1050 was commonly used as an off-line peripheral controller in many installations of both large "scientific computers and large "business computers". In these installations the big computer (e.g., a UNIVAC III) did all of its input-output on magnetic tapes and the 1050 was used to format input data from other peripherals (e.g., punched card readers) on the tapes and transfer output data from the tapes to other peripherals (e.g., punched card punches or the line printer).

UNIVAC 1050, Netherlands 1964 Opdracht Univac, Bestanddeelnr 917-0538.jpg
UNIVAC 1050, Netherlands 1964
UNIVAC 1050-II console UNIVAC 1050-II.jpg
UNIVAC 1050-II console

A version used by the U.S. Air Force, the U1050-II real-time system, had some extra peripherals. The most significant of these was the FASTRAND 1 Drum Storage Unit. This physically large device had two contra-rotating drums mounted horizontally, one above the other in a pressurized cabinet. Read-write heads were mounted on a horizontally moving beam between the drums, driven by a voice coil servo external to the pressurized cabinet. This high-speed access subsystem allowed the real-time operation. Another feature was the communications subsystem with modem links to remote sites. A Uniservo VI-C tape drive provided an audit trail for the transactions. Other peripherals were the card reader and punch, and printer. The operator's console had the 'stop and go' buttons and a Teletype Model 33 teleprinter for communication and control. The initial Air Force order in November 1963 was for 152 systems. [2]

Subsequently, UNIVAC released the 1050 Model III (1050-III) and 1050 Model IV (1050-IV) for general purpose Commercial usage. The key difference between the two models was that of performance and expandability. The 1050-IV could be expanded to 64K of character addressable memory which could be accessed at two characters at a time with a cycle time of 2 microseconds per access (vs. 4.5 Microseconds in the 1050-III). Both models supported Decimal Multiply/Divide as an upgrade option. [1]

Related Research Articles

<span class="mw-page-title-main">IBM System/360</span> IBM mainframe computer family (1964–1977)

The IBM System/360 (S/360) is a family of mainframe computer systems that was announced by IBM on April 7, 1964, and delivered between 1965 and 1978. It was the first family of computers designed to cover both commercial and scientific applications and a complete range of applications from small to large. The design distinguished between architecture and implementation, allowing IBM to release a suite of compatible designs at different prices. All but the only partially compatible Model 44 and the most expensive systems use microcode to implement the instruction set, featuring 8-bit byte addressing and fixed point binary, fixed point decimal and hexadecimal floating-point calculations.

The Honeywell 6000 series computers were rebadged versions of General Electric's 600-series mainframes manufactured by Honeywell International, Inc. from 1970 to 1989. Honeywell acquired the line when it purchased GE's computer division in 1970 and continued to develop them under a variety of names for many years. In 1989, Honeywell sold its computer division to the French company Groupe Bull who continued to market compatible machines.

<span class="mw-page-title-main">IBM 1620</span> Small IBM scientific computer released in 1959

The IBM 1620 was announced by IBM on October 21, 1959, and marketed as an inexpensive scientific computer. After a total production of about two thousand machines, it was withdrawn on November 19, 1970. Modified versions of the 1620 were used as the CPU of the IBM 1710 and IBM 1720 Industrial Process Control Systems.

<span class="mw-page-title-main">IBM 1401</span> 1960s decimal computer

The IBM 1401 is a variable-wordlength decimal computer that was announced by IBM on October 5, 1959. The first member of the highly successful IBM 1400 series, it was aimed at replacing unit record equipment for processing data stored on punched cards and at providing peripheral services for larger computers. The 1401 is considered by IBM to be the Ford Model-T of the computer industry due to its mass appeal. Over 12,000 units were produced and many were leased or resold after they were replaced with newer technology. The 1401 was withdrawn on February 8, 1971.

<span class="mw-page-title-main">UNIVAC I</span> First general-purpose computer designed for business application (1951)

The UNIVAC I was the first general-purpose electronic digital computer design for business application produced in the United States. It was designed principally by J. Presper Eckert and John Mauchly, the inventors of the ENIAC. Design work was started by their company, Eckert–Mauchly Computer Corporation (EMCC), and was completed after the company had been acquired by Remington Rand. In the years before successor models of the UNIVAC I appeared, the machine was simply known as "the UNIVAC".

<span class="mw-page-title-main">IBM 650</span> Vacuum-tube 1950s computer system

The IBM 650 Magnetic Drum Data-Processing Machine is an early digital computer produced by IBM in the mid-1950s. It was the first mass-produced computer in the world. Almost 2,000 systems were produced, the last in 1962, and it was the first computer to make a meaningful profit. The first one was installed in late 1954 and it was the most popular computer of the 1950s.

<span class="mw-page-title-main">UNIVAC</span> Series of mainframe computer models

UNIVAC was a line of electronic digital stored-program computers starting with the products of the Eckert–Mauchly Computer Corporation. Later the name was applied to a division of the Remington Rand company and successor organizations.

<span class="mw-page-title-main">UNIVAC 1100/2200 series</span> Family of mainframe computers

The UNIVAC 1100/2200 series is a series of compatible 36-bit computer systems, beginning with the UNIVAC 1107 in 1962, initially made by Sperry Rand. The series continues to be supported today by Unisys Corporation as the ClearPath Dorado Series. The solid-state 1107 model number was in the same sequence as the earlier vacuum-tube computers, but the early computers were not compatible with their solid-state successors.

<span class="mw-page-title-main">IBM 700/7000 series</span> Mainframe computer systems made by IBM through the 1950s and early 1960s

The IBM 700/7000 series is a series of large-scale (mainframe) computer systems that were made by IBM through the 1950s and early 1960s. The series includes several different, incompatible processor architectures. The 700s use vacuum-tube logic and were made obsolete by the introduction of the transistorized 7000s. The 7000s, in turn, were eventually replaced with System/360, which was announced in 1964. However the 360/65, the first 360 powerful enough to replace 7000s, did not become available until November 1965. Early problems with OS/360 and the high cost of converting software kept many 7000s in service for years afterward.

<span class="mw-page-title-main">UNIVAC LARC</span> Livermore Advanced Research Computer

The UNIVAC LARC, short for the Livermore Advanced Research Computer, is a mainframe computer designed to a requirement published by Edward Teller in order to run hydrodynamic simulations for nuclear weapon design. It was one of the earliest supercomputers.

<span class="mw-page-title-main">IBM 1400 series</span> Mid-range business decimal computers

The IBM 1400 series are second-generation (transistor) mid-range business decimal computers that IBM marketed in the early 1960s. The computers were offered to replace tabulating machines like the IBM 407. The 1400-series machines stored information in magnetic cores as variable-length character strings separated on the left by a special bit, called a "wordmark," and on the right by a "record mark." Arithmetic was performed digit-by-digit. Input and output support included punched card, magnetic tape, and high-speed line printers. Disk storage was also available.

<span class="mw-page-title-main">English Electric DEUCE</span>

The DEUCE was one of the earliest British commercially available computers, built by English Electric from 1955. It was the production version of the Pilot ACE, itself a cut-down version of Alan Turing's ACE.

<span class="mw-page-title-main">Bendix G-15</span> 1956 computer design

The Bendix G-15 is a computer introduced in 1956 by the Bendix Corporation, Computer Division, Los Angeles, California. It is about 5 by 3 by 3 feet and weighs about 966 pounds (438 kg). The G-15 has a drum memory of 2,160 29-bit words, along with 20 words used for special purposes and rapid-access storage. The base system, without peripherals, cost $49,500. A working model cost around $60,000. It could also be rented for $1,485 per month. It was meant for scientific and industrial markets. The series was gradually discontinued when Control Data Corporation took over the Bendix computer division in 1963.

The UNIVAC 418 was a transistorized, 18-bit word magnetic-core memory machine made by Sperry Univac. The name came from its 4-microsecond memory cycle time and 18-bit word. The assembly language for this class of computers was TRIM III and ART418.

<span class="mw-page-title-main">UNIVAC II</span> Vacuum tube commercial computer, 1958

The UNIVAC II computer was an improvement to the UNIVAC I that the UNIVAC division of Sperry Rand first delivered in 1958. The improvements included the expansion of core memory from 2,000 to 10,000 words; UNISERVO II tape drives, which could use either the old UNIVAC I metal tapes or the new PET tapes; and some transistorized circuits. It was fully compatible with existing UNIVAC I programs for both code and data. It weighed about 16,000 pounds.

<span class="mw-page-title-main">IBM 7070</span> Decimal computer introduced by IBM in 1958

IBM 7070 is a decimal-architecture intermediate data-processing system that was introduced by IBM in 1958. It was part of the IBM 700/7000 series, and was based on discrete transistors rather than the vacuum tubes of the 1950s. It was the company's first transistorized stored-program computer.

<span class="mw-page-title-main">NCR 315</span>

The NCR 315 Data Processing System, released in January 1962 by NCR, is a second-generation computer. All printed circuit boards use resistor–transistor logic (RTL) to create the various logic elements. It uses 12-bit slab memory structure using magnetic-core memory. The instructions can use a memory slab as either two 6-bit alphanumeric characters or as three 4-bit BCD digits. Basic memory is 5000 "slabs" of handmade core memory, which is expandable to a maximum of 40,000 slabs in four refrigerator-size cabinets. The main processor includes three cabinets and a console section that houses the power supply, keyboard, output writer, and a panel with lights that indicate the current status of the program counter, registers, arithmetic accumulator, and system errors. Input/Output is by direct parallel connections to each type of peripheral through a two-cable bundle with 1-inch-thick cables. Some devices like magnetic tape and the CRAM are daisy-chained to allow multiple drives to be connected.

<span class="mw-page-title-main">RCA Spectra 70</span> Series of mainframe computers manufactured by RCA starting in 1965

The RCA Spectra 70 is a line of electronic data processing (EDP) equipment that was manufactured by the Radio Corporation of America’s computer division beginning in April 1965. The Spectra 70 line included several CPU models, various configurations of core memory, mass-storage devices, terminal equipment, and a variety of specialized interface equipment.

<span class="mw-page-title-main">English Electric System 4</span>

The English Electric System 4 was a mainframe computer announced in 1965. It was derived from the RCA Spectra 70 range, itself a variant of the IBM System 360 architecture.

<span class="mw-page-title-main">IBM System/360 Model 20</span> Low-end IBM computer model from 1960s

The IBM System/360 Model 20 is the smallest member of the IBM System/360 family announced in November 1964. The Model 20 supports only a subset of the System/360 instruction set, with binary numbers limited to 16 bits and no floating point. In later years it would have been classified as a 16-bit minicomputer rather than a mainframe, but the term "minicomputer" was not current, and in any case IBM wanted to emphasize the compatibility of the Model 20 rather than its differences from the rest of the System/360 line. It does, however, have the full System/360 decimal instruction set, that allows for addition, subtraction, product, and dividend of up to 31 decimal digits.

References

  1. 1 2 3 http://www.bitsavers.org/pdf/auerbach/Auerbach_Standard_EDP_Reports_196609_Volume_8_Univac.pdf
  2. Gene Smith (27 August 1964). "Past and Present Officials Deny Wall St. Rumor of Univac Woes". The New York Times. pp. 45, 50.