Electric spark

Last updated
A spark on a spark plug Spark-plug01.jpeg
A spark on a spark plug
Lightning is a natural example of an electric spark. Lightning NOAA.jpg
Lightning is a natural example of an electric spark.

An electric spark is an abrupt electrical discharge that occurs when a sufficiently high electric field creates an ionized, electrically conductive channel through a normally-insulating medium, often air or other gases or gas mixtures. Michael Faraday described this phenomenon as "the beautiful flash of light attending the discharge of common electricity". [1]

Contents

The rapid transition from a non-conducting to a conductive state produces a brief emission of light and a sharp crack or snapping sound. A spark is created when the applied electric field exceeds the dielectric breakdown strength of the intervening medium. For air, the breakdown strength is about 30 kV/cm at sea level. [2] Experimentally, this figure tends to differ depending upon humidity, atmospheric pressure, shape of electrodes (needle and ground-plane, hemispherical etc.) and the corresponding spacing between them and even the type of waveform, whether sinusoidal or cosine-rectangular. At the beginning stages, free electrons in the gap (from cosmic rays or background radiation) are accelerated by the electrical field. As they collide with air molecules, they create additional ions and newly freed electrons which are also accelerated. At some point, thermal energy will provide a much greater source of ions. The exponentially-increasing electrons and ions rapidly cause regions of the air in the gap to become electrically conductive in a process called dielectric breakdown. Once the gap breaks down, current flow is limited by the available charge (for an electrostatic discharge) or by the impedance of the external power supply. If the power supply continues to supply current, the spark will evolve into a continuous discharge called an electric arc. An electric spark can also occur within insulating liquids or solids, but with different breakdown mechanisms from sparks in gases.

Sometimes, sparks can be dangerous. They can cause fires and burn skin.

Lightning is an example of an electric spark in nature, while electric sparks, large or small, occur in or near many man-made objects, both by design and sometimes by accident.

History

Benjamin Franklin drawing an electric spark to his finger from a key suspended from a kite string. Franklin lightning engraving.jpg
Benjamin Franklin drawing an electric spark to his finger from a key suspended from a kite string.

In 1671, Leibniz discovered that sparks were associated with electrical phenomena. [3] In 1708, Samuel Wall performed experiments with amber rubbed with cloth to produce sparks. [4] In 1752, Thomas-François Dalibard, acting on an experiment proposed by Benjamin Franklin, arranged for a retired French dragoon named Coiffier in the village of Marly to collect lightning in a Leyden jar [5] thereby proving that lightning and electricity are the same. In Franklin's famous kite experiment, he successfully extracted sparks from a cloud during a thunderstorm.

Uses

Gas stove burner - the electric spark flame igniter is shown at the left. Gas cooker blue flame.jpg
Gas stove burner - the electric spark flame igniter is shown at the left.
Spark transmitter used for ship to shore communication up to 10 km (c. 1900)." Spark gap transmitter.jpg
Spark transmitter used for ship to shore communication up to 10 km (c. 1900)."

Ignition sources

Electric sparks are used in spark plugs in gasoline internal combustion engines to ignite fuel and air mixtures. [6] The electric discharge in a spark plug occurs between an insulated central electrode and a grounded terminal on the base of the plug. The voltage for the spark is provided by an ignition coil or magneto that is connected to the spark plug with an insulated wire.

Flame igniters use electric sparks to initiate combustion in some furnaces and gas stoves in place of a pilot flame. [7] Auto reignition is a safety feature that is used in some flame igniters that senses the electrical conductivity of the flame and uses this information to determine whether a burner flame is lit. [8] This information is used to stop an ignition device from sparking after the flame is lit or restart the flame if it goes out.

Radio communications

A spark-gap transmitter uses an electric spark gap to generate radio frequency electromagnetic radiation that can be used as transmitters for wireless communication. [9] Spark gap transmitters were widely used in the first three decades of radio from 1887–1916. They were later supplanted by vacuum tube systems and by 1940 were no longer used for communication. The wide use of spark-gap transmitters led to the nickname "sparks" for a ship's radio officer.

Metalworking

Electric sparks are used in different kinds of metalworking. Electric discharge machining (EDM) is sometimes called spark machining and uses a spark discharge to remove material from a workpiece. [10] Electrical discharge machining is used for hard metals or those that are difficult to machine with traditional techniques.

Spark plasma sintering (SPS) is a sintering technique that uses a pulsed direct current that passes through a conductive powder in a graphite die. [11] SPS is faster than conventional hot isostatic pressing, where the heat is provided by external heating elements.

Chemical analysis

The light that is produced by electric sparks can be collected and used for a type of spectroscopy called spark emission spectroscopy. [12]

A high energy pulsed laser can be used to produce an electric spark. Laser induced breakdown spectroscopy (LIBS) is a type of atomic emission spectroscopy that uses a high pulse energy laser to excite atoms in a sample. LIBS has also been called laser spark spectroscopy (LSS). [13]

Electric sparks can also be used to create ions for mass spectrometry. [14] Spark discharge has been also applied in electrochemical sensing via the in-situ surface modification of disposable screen printed carbon electrodes (SPEs) with various metal and carbon sources. [15] [16] [17] [18] [19]

Hazards

An electric spark produced by a stun gun. At 150,000 volts, the spark can easily jump a gap greater than 25 mm (1 in). Electric spark from a stun gun 150000 volts.jpg
An electric spark produced by a stun gun. At 150,000 volts, the spark can easily jump a gap greater than 25 mm (1 in).

Sparks can be hazardous to people, animals or even inanimate objects. Electric sparks can ignite flammable materials, liquids, gases and vapors. Even inadvertent static-discharges, or small sparks that occur when switching on lights or other circuits, can be enough to ignite flammable vapors from sources like gasoline, acetone, propane, or dust concentrations in the air, such as those found in flour mills or more generally in factories handling powders. [20] [21]

Sparks often indicate the presence of a high voltage, or "potential field". The higher the voltage; the farther a spark can jump across a gap, and with enough energy supplied can lead to greater discharges such as a glow or an arc. When a person is charged with high-voltage static-charges, or is in the presence of high-voltage electrical supplies, a spark can jump between a conductor and a person who is in close enough proximity, allowing the release of much higher energies that can cause severe burns, shut down the heart and internal organs, or even develop into an arc flash.

High-voltage sparks, even those with low energy such as from a stun gun, can overload the conductive pathways of the nervous system, causing involuntary muscle-contractions, or interfere with vital nervous-system functions such as heart rhythm. When the energy is low enough most of it may be used just heating the air, so the spark never fully stabilizes into a glow or arc. However, sparks with very low energy still produce a "plasma tunnel" through the air, through which electricity can pass. This plasma is heated to temperatures often greater than the surface of the Sun, and can cause small, localized burns. Conductive liquids, gels or ointments are often used when applying electrodes to a person's body, preventing sparks from forming at the point of contact and damaging skin. Similarly, sparks can cause damage to metals and other conductors, ablating or pitting the surface; a phenomenon which is exploited in electric etching. Sparks also produce ozone which, in high enough concentrations, can cause respiratory discomfort or distress, itching, or tissue damage, and can be harmful to other materials such as certain plastics. [22] [23]

See also

Related Research Articles

<span class="mw-page-title-main">Tesla coil</span> Electrical resonant transformer circuit invented by Nikola Tesla

A Tesla coil is an electrical resonant transformer circuit designed by inventor Nikola Tesla in 1891. It is used to produce high-voltage, low-current, high-frequency alternating-current electricity. Tesla experimented with a number of different configurations consisting of two, or sometimes three, coupled resonant electric circuits.

<span class="mw-page-title-main">Van de Graaff generator</span> Electrostatic particle accelerator operating on the triboelectric effect

A Van de Graaff generator is an electrostatic generator which uses a moving belt to accumulate electric charge on a hollow metal globe on the top of an insulated column, creating very high electric potentials. It produces very high voltage direct current (DC) electricity at low current levels. It was invented by American physicist Robert J. Van de Graaff in 1929. The potential difference achieved by modern Van de Graaff generators can be as much as 5 megavolts. A tabletop version can produce on the order of 100 kV and can store enough energy to produce visible electric sparks. Small Van de Graaff machines are produced for entertainment, and for physics education to teach electrostatics; larger ones are displayed in some science museums.

<span class="mw-page-title-main">Electrostatic discharge</span> Sudden flow of electric current between two electrically charged objects by contact

Electrostatic discharge (ESD) is a sudden and momentary flow of electric current between two differently-charged objects when brought close together or when the dielectric between them breaks down, often creating a visible spark associated with the static electricity between the objects.

<span class="mw-page-title-main">Electrical discharge machining</span> Metal fabrication process

Electrical discharge machining (EDM), also known as spark machining, spark eroding, die sinking, wire burning or wire erosion, is a metal fabrication process whereby a desired shape is obtained by using electrical discharges (sparks). Material is removed from the work piece by a series of rapidly recurring current discharges between two electrodes, separated by a dielectric liquid and subject to an electric voltage. One of the electrodes is called the tool-electrode, or simply the tool or electrode, while the other is called the workpiece-electrode, or work piece. The process depends upon the tool and work piece not making physical contact. Extremely hard materials like carbides, ceramics, titanium alloys and heat treated tool steels that are very difficult to machine using conventional machining can be precisely machined by EDM.

<span class="mw-page-title-main">Static electricity</span> Imbalance of electric charges within or on the surface of a material

Static electricity is an imbalance of electric charges within or on the surface of a material. The charge remains until it can move away by an electric current or electrical discharge. The word "static" is used to differentiate it from current electricity, where an electric charge flows through an electrical conductor.

<span class="mw-page-title-main">Spark gap</span> Two conducting electrodes separated in order to allow an electric spark to pass between

A spark gap consists of an arrangement of two conducting electrodes separated by a gap usually filled with a gas such as air, designed to allow an electric spark to pass between the conductors. When the potential difference between the conductors exceeds the breakdown voltage of the gas within the gap, a spark forms, ionizing the gas and drastically reducing its electrical resistance. An electric current then flows until the path of ionized gas is broken or the current reduces below a minimum value called the "holding current". This usually happens when the voltage drops, but in some cases occurs when the heated gas rises, stretching out and then breaking the filament of ionized gas. Usually, the action of ionizing the gas is violent and disruptive, often leading to sound, light, and heat.

<span class="mw-page-title-main">Corona discharge</span> Ionization of air around a high-voltage conductor

A corona discharge is an electrical discharge caused by the ionization of a fluid such as air surrounding a conductor carrying a high voltage. It represents a local region where the air has undergone electrical breakdown and become conductive, allowing charge to continuously leak off the conductor into the air. A corona discharge occurs at locations where the strength of the electric field around a conductor exceeds the dielectric strength of the air. It is often seen as a bluish glow in the air adjacent to pointed metal conductors carrying high voltages, and emits light by the same mechanism as a gas discharge lamp. Corona discharges can also happen in weather, such as thunderstorms, where objects like ship masts or airplane wings have a charge significantly different from the air around them.

<span class="mw-page-title-main">Lichtenberg figure</span> Branching shapes

A Lichtenberg figure, or Lichtenberg dust figure, is a branching electric discharge that sometimes appears on the surface or in the interior of insulating materials. Lichtenberg figures are often associated with the progressive deterioration of high voltage components and equipment. The study of planar Lichtenberg figures along insulating surfaces and 3D electrical trees within insulating materials often provides engineers with valuable insights for improving the long-term reliability of high-voltage equipment. Lichtenberg figures are now known to occur on or within solids, liquids, and gases during electrical breakdown.

<span class="mw-page-title-main">Paschen's law</span> Physical law about electrical discharge in gases

Paschen's law is an equation that gives the breakdown voltage, that is, the voltage necessary to start a discharge or electric arc, between two electrodes in a gas as a function of pressure and gap length. It is named after Friedrich Paschen who discovered it empirically in 1889.

<span class="mw-page-title-main">Electrical breakdown</span> Conduction of electricity through an insulator under sufficiently high voltage

In electronics, electrical breakdown or dielectric breakdown is a process that occurs when an electrically insulating material, subjected to a high enough voltage, suddenly becomes a conductor and current flows through it. All insulating materials undergo breakdown when the electric field caused by an applied voltage exceeds the material's dielectric strength. The voltage at which a given insulating object becomes conductive is called its breakdown voltage and, in addition to its dielectric strength, depends on its size and shape, and the location on the object at which the voltage is applied. Under sufficient voltage, electrical breakdown can occur within solids, liquids, or gases. However, the specific breakdown mechanisms are different for each kind of dielectric medium.

<span class="mw-page-title-main">High voltage</span> Electrical potential which is large enough to cause damage or injury

High voltage electricity refers to electrical potential large enough to cause injury or damage. In certain industries, high voltage refers to voltage above a certain threshold. Equipment and conductors that carry high voltage warrant special safety requirements and procedures.

<span class="mw-page-title-main">Electric arc</span> Electrical breakdown of a gas that results in an ongoing electrical discharge

An electric arc is an electrical breakdown of a gas that produces a prolonged electrical discharge. The current through a normally nonconductive medium such as air produces a plasma, which may produce visible light. An arc discharge is initiated either by thermionic emission or by field emission. After initiation, the arc relies on thermionic emission of electrons from the electrodes supporting the arc. An arc discharge is characterized by a lower voltage than a glow discharge. An archaic term is voltaic arc, as used in the phrase "voltaic arc lamp".

<span class="mw-page-title-main">Electrostatic precipitator</span> Filtration device

An electrostatic precipitator (ESP) is a filterless device that removes fine particles, such as dust and smoke, from a flowing gas using the force of an induced electrostatic charge minimally impeding the flow of gases through the unit.

<span class="mw-page-title-main">Nitrogen laser</span>

A nitrogen laser is a gas laser operating in the ultraviolet range using molecular nitrogen as its gain medium, pumped by an electrical discharge.

An electron avalanche is a process in which a number of free electrons in a transmission medium are subjected to strong acceleration by an electric field and subsequently collide with other atoms of the medium, thereby ionizing them. This releases additional electrons which accelerate and collide with further atoms, releasing more electrons—a chain reaction. In a gas, this causes the affected region to become an electrically conductive plasma.

<span class="mw-page-title-main">Electric discharge</span> Flow of electric current through a non-metal medium

In electromagnetism, an electric discharge is the release and transmission of electricity in an applied electric field through a medium such as a gas.

In electromagnetism, a leader is a hot, highly conductive channel of plasma that plays a critical part during dielectric breakdown within a long electric spark.

<span class="mw-page-title-main">Brush discharge</span> Ionization of air characterized as writhing streamers and sparks

A brush discharge is an electrical disruptive discharge similar to a corona discharge that takes place at an electrode with a high voltage applied to it, embedded in a nonconducting fluid, usually air. It is characterized by numerous luminous writhing sparks, plasma streamers composed of ionized air molecules, which repeatedly strike out from the electrode into the air, often with a crackling sound. The streamers spread out in a fan shape, giving it the appearance of a "brush".

<span class="mw-page-title-main">Spark ionization</span> Ionization method to produce gas phase ions from a solid sample

Spark ionization is a method used to produce gas phase ions from a solid sample. The prepared solid sample is vaporized and partially ionized by an intermittent discharge or spark. This technique is primarily used in the field of mass spectrometry. When incorporated with a mass spectrometer the complete instrument is referred to as a spark ionization mass spectrometer or as a spark source mass spectrometer (SSMS).

References

  1. ↑ Faraday, Experimental Researches in Electricity, volume 1 paragraph 69.
  2. ↑ Meek, J. (1940). "A Theory of Spark Discharge". Physical Review. 57 (8): 722–728. Bibcode:1940PhRv...57..722M. doi:10.1103/PhysRev.57.722.
  3. ↑ Kryzhanovsky, L. N. (1989). "Mapping the history of electricity". Scientometrics. 17 (1–2): 165–170. doi:10.1007/BF02017730. S2CID   10668311.
  4. ↑ Heilbron, J. L.; Heilborn, J. L. (1979). Electricity in the 17th and 18th centuries: a study of early Modern physics. Berkeley: University of California Press. ISBN   978-0-520-03478-5.
  5. ↑ Michael Brian Schiffer, Draw the Lightning Down: Benjamin Franklin and Electrical Technology in the Age of Enlightenment. University of California Press, p 164
  6. ↑ Day, John (1975). The Bosch book of the Motor Car, Its evolution and engineering development. St. Martin's Press. pp. 206–207. LCCN   75-39516. OCLC   2175044.
  7. ↑ Bill Whitman; Bill Johnson; John Tomczyck (2004). Refrigeration and Air Conditioning Technology, 5E. Clifton Park, NY: Thomson Delmar Learning. pp. 677ff. ISBN   978-1-4018-3765-5.
  8. ↑ Ed Sobey (2010). The Way Kitchens Work: The Science Behind the Microwave, Teflon Pan, Garbage Disposal, and More. Chicago, Ill: Chicago Review Press. p. 116. ISBN   978-1-56976-281-3.
  9. ↑ Beauchamp, K. G. (2001). History of telegraphy. London: Institution of Electrical Engineers. ISBN   978-0-85296-792-8.
  10. ↑ Jameson, Elman C. (2001). Electrical discharge machining. Dearborn, Mich: Society of Manufacturing Engineers. ISBN   978-0-87263-521-0.
  11. ↑ Munir, Z. A.; Anselmi-Tamburini, U.; Ohyanagi, M. (2006). "The effect of electric field and pressure on the synthesis and consolidation of materials: A review of the spark plasma sintering method". Journal of Materials Science. 41 (3): 763. Bibcode:2006JMatS..41..763M. doi:10.1007/s10853-006-6555-2. S2CID   73570418.
  12. ↑ Walters, J. P. (1969). "Historical Advances in Spark Emission Spectroscopy". Applied Spectroscopy. 23 (4): 317–331. Bibcode:1969ApSpe..23..317W. doi:10.1366/000370269774380662. S2CID   96919495.
  13. ↑ Radziemski, Leon J.; Cremers, David A. (2006). Handbook of laser-induced breakdown spectroscopy. New York: John Wiley. ISBN   978-0-470-09299-6.
  14. ↑ Dempster, A. J. (1936). "Ion Sources for Mass Spectroscopy". Review of Scientific Instruments. 7 (1): 46–49. Bibcode:1936RScI....7...46D. doi:10.1063/1.1752028.
  15. ↑ Trachioti, Maria G.; Hrbac, Jan; Prodromidis, Mamas I. (May 2018). "Determination of Cd and Zn with "green" screen-printed electrodes modified with instantly prepared sparked tin nanoparticles". Sensors and Actuators B: Chemical. 260: 1076–1083. doi:10.1016/j.snb.2017.10.039.
  16. ↑ Trachioti, Maria G.; Karantzalis, Alexandros E.; Hrbac, Jan; Prodromidis, Mamas I. (February 2019). "Low-cost screen-printed sensors on-demand: Instantly prepared sparked gold nanoparticles from eutectic Au/Si alloy for the determination of arsenic at the sub-ppb level". Sensors and Actuators B: Chemical. 281: 273–280. doi:10.1016/j.snb.2018.10.112. S2CID   106204477.
  17. ↑ Trachioti, Maria G.; Tzianni, Eleni I.; Riman, Daniel; Jurmanova, Jana; Prodromidis, Mamas I.; Hrbac, Jan (May 2019). "Extended coverage of screen-printed graphite electrodes by spark discharge produced gold nanoparticles with a 3D positioning device. Assessment of sparking voltage-time characteristics to develop sensors with advanced electrocatalytic properties". Electrochimica Acta. 304: 292–300. doi:10.1016/j.electacta.2019.03.004. S2CID   104377649.
  18. ↑ Trachioti, Maria G.; Hemzal, Dusan; Hrbac, Jan; Prodromidis, Mamas I. (May 2020). "Generation of graphite nanomaterials from pencil leads with the aid of a 3D positioning sparking device: Application to the voltammetric determination of nitroaromatic explosives". Sensors and Actuators B: Chemical. 310: 127871. doi:10.1016/j.snb.2020.127871. S2CID   213989070.
  19. ↑ Trachioti, Maria G.; Hrbac, Jan; Prodromidis, Mamas I. (October 2021). "Determination of 8−hydroxy−2ˊ−deoxyguanosine in urine with "linear" mode sparked graphite screen-printed electrodes". Electrochimica Acta. 399: 139371. doi:10.1016/j.electacta.2021.139371. ISSN   0013-4686. S2CID   240654358.
  20. ↑ An Introduction to Physical Science by James Shipman, Jerry D. Wilson, Charles A. Higgins, Omar Torres -- Cengage Learning 2016 Page 202
  21. ↑ Dust explosion electrostatics hazards https://powderprocess.net/Safety/Electrostatics_Risks_ATEX_DSEAR.html Archived 2019-02-07 at the Wayback Machine
  22. ↑ Management of Hazardous Energy: Deactivation, De-Energization, Isolation, and Lock-out By Thomas Neil McManus -- CRC Press 2013 Page 79--80, 95--96, 231, 346, 778, 780
  23. ↑ Electrostatic Hazards by Günter Luttgens, Norman Wilson -- Reed Professional and Educational Publishing Ltd. 1997
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.