Motorola 88100

	MC88100 Registers
	General Purpose Registers
R0	Zero (Read-only register that contains zero)
R1	Subroutine Return Pointer
R30	Frame Pointer (Pointer to stack frame)
R31	Stack Pointer

Last updated August 27, 2023

The MC88100 is a microprocessor developed by Motorola that implemented 88000 RISC instruction set architecture. Announced in 1988, the MC88100 was the first 88000 implementation. It was succeeded by the MC88110 in the early 1990s.

The microprocessor has separate pipelined integer, floating-point add, floating-point multiply, and load/store execution units and dispatches a single instruction (at most) per clock cycle. The separate MC88200 integrated circuit optionally add level 1 cache and a paged memory management unit. An MC88100 system typically used two of these devices for instructions and data; additional MC88200s could be added to increase the size of the caches.

This partitioned scheme was chosen to provide system flexibility, the amount of cache could be varied depending on the price point. In practice, these additional chips required more space on the circuit board and the buses between the MC88200s and MC88100 added complexity and cost.

The MC88100 contained 165,000 transistors and the MC88200 750,000 transistors. Both were fabricated by Motorola in its 1.5 μm complementary metal–oxide–semiconductor process.

The MC88100 was ultimately commercially unsuccessful.^{[ citation needed ]} This was due to a number of reasons, including requirement of MC88200s in most cases^{[lower-alpha 1]}, but was mostly due to Motorola being a vendor of the highly successful 68000 family. As the 68000 division viewed the 88000 as a competitor, they forced the MC88100 to be priced unacceptably high for a volume part.^{[ citation needed ]} The part did find use in the high-end embedded market, in Motorola's own computers, and in large computers from companies such as Data General and the Unisys S-8400 Unix Servers.

Design

Programming model and register set

The programming model and register set of the MC88100 is remarkably similar to DLX (and by extension, RISC-V) based CPUs, with 32 General-purpose registers (31 writable) and 51 instructions capable of accessing any of the 32 general-purpose registers at any time.

Registers

The MC88100 is equipped with a total of 64 user-accessible registers, 32 of them being Control registers, and can access up to 6 registers (4 read, 2 write) simultaneously. The actual usage of GPR is not enforced by the processor for every register except R1, which is used as a return address.

Notes

↑ The 88200 adds a cache and a MMU. Typically a pair of 88200s is used to change the 88100's Harvard architecture (separate instruction and data memories) to a modified Harvard architecture (unified memory).^[1] NCD used the 88100 on its own (without 88200s) in its 88K X-Terminals.

Related Research Articles

A complex instruction set computer is a computer architecture in which single instructions can execute several low-level operations or are capable of multi-step operations or addressing modes within single instructions. The term was retroactively coined in contrast to reduced instruction set computer (RISC) and has therefore become something of an umbrella term for everything that is not RISC, where the typical differentiating characteristic is that most RISC designs use uniform instruction length for almost all instructions, and employ strictly separate load and store instructions.

The Motorola 68000 is a 16/32-bit complex instruction set computer (CISC) microprocessor, introduced in 1979 by Motorola Semiconductor Products Sector.

PowerPC is a reduced instruction set computer (RISC) instruction set architecture (ISA) created by the 1991 Apple–IBM–Motorola alliance, known as AIM. PowerPC, as an evolving instruction set, has been named Power ISA since 2006, while the old name lives on as a trademark for some implementations of Power Architecture–based processors.

In computer science, a reduced instruction set computer (RISC) is a computer architecture designed to simplify the individual instructions given to the computer to accomplish tasks. Compared to the instructions given to a complex instruction set computer (CISC), a RISC computer might require more instructions in order to accomplish a task because the individual instructions are written in simpler code. The goal is to offset the need to process more instructions by increasing the speed of each instruction, in particular by implementing an instruction pipeline, which may be simpler to achieve given simpler instructions.

The NS32000, sometimes known as the 32k, is a series of microprocessors produced by National Semiconductor. The first member of the family came to market in 1982, briefly known as the 16032 before becoming the 32016. It was the first general-purpose microprocessor on the market that used 32-bit data throughout: the Motorola 68000 used 32-bit data but had a 16-bit ALU and thus took twice as long perform many operations. However, the 32016 contained a large number of bugs and often could not be run at its rated speed. These problems, and the presence of the otherwise similar 68000 which had been available since 1980, led to little use in the market.

The 88000 is a RISC instruction set architecture developed by Motorola during the 1980s. The MC88100 arrived on the market in 1988, some two years after the competing SPARC and MIPS. Due to the late start and extensive delays releasing the second-generation MC88110, the m88k achieved very limited success outside of the MVME platform and embedded controller environments. When Motorola joined the AIM alliance in 1991 to develop the PowerPC, further development of the 88000 ended.

The Motorola 68000 series is a family of 32-bit complex instruction set computer (CISC) microprocessors. During the 1980s and early 1990s, they were popular in personal computers and workstations and were the primary competitors of Intel's x86 microprocessors. They were best known as the processors used in the early Apple Macintosh, the Sharp X68000, the Commodore Amiga, the Sinclair QL, the Atari ST, the Sega Genesis, the Capcom System I (Arcade), the AT&T UNIX PC, the Tandy Model 16/16B/6000, the Sun Microsystems Sun-1, Sun-2 and Sun-3, the NeXT Computer, NeXTcube, NeXTstation, and NeXTcube Turbo, the Texas Instruments TI-89/TI-92 calculators, the Palm Pilot and the Space Shuttle. Although no modern desktop computers are based on processors in the 680x0 series, derivative processors are still widely used in embedded systems.

The Intel i860 is a RISC microprocessor design introduced by Intel in 1989. It is one of Intel's first attempts at an entirely new, high-end instruction set architecture since the failed Intel iAPX 432 from the beginning of the 1980s. It was the world's first million-transistor chip. It was released with considerable fanfare, slightly obscuring the earlier Intel i960, which was successful in some niches of embedded systems. The i860 never achieved commercial success and the project was terminated in the mid-1990s.

The POWER1 is a multi-chip CPU developed and fabricated by IBM that implemented the POWER instruction set architecture (ISA). It was originally known as the RISC System/6000 CPU or, when in an abbreviated form, the RS/6000 CPU, before introduction of successors required the original name to be replaced with one that used the same naming scheme (POWERn) as its successors in order to differentiate it from the newer designs.

Berkeley RISC is one of two seminal research projects into reduced instruction set computer (RISC) based microprocessor design taking place under the Defense Advanced Research Projects Agency VLSI Project. RISC was led by David Patterson at the University of California, Berkeley between 1980 and 1984. The other project took place a short distance away at Stanford University under their MIPS effort starting in 1981 and running until 1984.

The R4000 is a microprocessor developed by MIPS Computer Systems that implements the MIPS III instruction set architecture (ISA). Officially announced on 1 October 1991, it was one of the first 64-bit microprocessors and the first MIPS III implementation. In the early 1990s, when RISC microprocessors were expected to replace CISC microprocessors such as the Intel i486, the R4000 was selected to be the microprocessor of the Advanced Computing Environment (ACE), an industry standard that intended to define a common RISC platform. ACE ultimately failed for a number of reasons, but the R4000 found success in the workstation and server markets.

The PowerPC 600 family was the first family of PowerPC processors built. They were designed at the Somerset facility in Austin, Texas, jointly funded and staffed by engineers from IBM and Motorola as a part of the AIM alliance. Somerset was opened in 1992 and its goal was to make the first PowerPC processor and then keep designing general purpose PowerPC processors for personal computers. The first incarnation became the PowerPC 601 in 1993, and the second generation soon followed with the PowerPC 603, PowerPC 604 and the 64-bit PowerPC 620.

The NEC V60 is a CISC microprocessor manufactured by NEC starting in 1986. Several improved versions were introduced with the same instruction set architecture (ISA), the V70 in 1987, and the V80 and AFPP in 1989. They were succeeded by the V800 product families, which is currently produced by Renesas Electronics.

<span class="mw-page-title-main">History of general-purpose CPUs</span> History of processors used in general purpose computers

The history of general-purpose CPUs is a continuation of the earlier history of computing hardware.

The Alpha 21264 is a Digital Equipment Corporation RISC microprocessor launched on 19 October 1998. The 21264 implemented the Alpha instruction set architecture (ISA).

The R2000 is a 32-bit microprocessor chip set developed by MIPS Computer Systems that implemented the MIPS I instruction set architecture (ISA). Introduced in January 1986, it was the first commercial implementation of the MIPS architecture and the first commercial RISC processor available to all companies. The R2000 competed with Digital Equipment Corporation (DEC) VAX minicomputers and with Motorola 68000 and Intel Corporation 80386 microprocessors. R2000 users included Ardent Computer, DEC, Silicon Graphics, Northern Telecom and MIPS's own Unix workstations.

The MC88110 was a microprocessor developed by Motorola that implemented the 88000 instruction set architecture (ISA). The MC88110 was a second-generation implementation of the 88000 ISA, succeeding the MC88100. It was designed for use in personal computers and workstations.

In computer engineering, a register–memory architecture is an instruction set architecture that allows operations to be performed on memory, as well as registers. If the architecture allows all operands to be in memory or in registers, or in combinations, it is called a "register plus memory" architecture.

IBM POWER is a reduced instruction set computer (RISC) instruction set architecture (ISA) developed by IBM. The name is an acronym for Performance Optimization With Enhanced RISC.

IBM Power microprocessors are designed and sold by IBM for servers and supercomputers. The name "POWER" was originally presented as an acronym for "Performance Optimization With Enhanced RISC". The Power line of microprocessors has been used in IBM's RS/6000, AS/400, pSeries, iSeries, System p, System i, and Power Systems lines of servers and supercomputers. They have also been used in data storage devices and workstations by IBM and by other server manufacturers like Bull and Hitachi.

References

↑ MC881100 User's Manual, Figure 1-2 and §1.2.7.

Furber, Stephen Bo (1989). VLSI RISC Architecture and Organization. CRC Press. pp. 184–192.
Tabak, Daniel (1990). RISC Systems. Research Studies Press. pp. 121–143.
Tabak, Daniel (1995). Advanced Microprocessors (2 ed.). McGraw-Hill. pp. 433–434, 437. ISBN 9780070628434.
Motorola, Inc., ed. (1990). MC88100 RISC Microprocessor User's Manual (PDF) (2nd ed.). Prentice Hall. ISBN 013567090X . Retrieved 25 August 2023.

This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.

[2] The 88200 adds a cache and a MMU. Typically a pair of 88200s is used to change the 88100's Harvard architecture (separate instruction and data memories) to a modified Harvard architecture (unified memory).^[1] NCD used the 88100 on its own (without 88200s) in its 88K X-Terminals.

[1] MC881100 User's Manual, Figure 1-2 and §1.2.7.

[lower-alpha 1]

[1]