The AeroLift CycloCrane was a unique UShybrid airship which adopted helicopter derived airfoil control for low speed flight manoeuvring by spinning on its axis. It was intended to be a heavy load lifter, initially aimed at the Canadian logging industry. A proof of concept vehicle flew at times during the 1980s, but no large production aircraft were built.
AeroLift Inc was set up in 1980 by CycloCrane inventor Arthur Crimmins, with funding from five major Canadian logging companies, with the objective of building a hybrid airship capable of conducting aerial logging at remote sites inaccessible by conventional means. The CycloCrane was a most unusual aircraft, utterly unique in its method of three-dimensional drive and attitude control.[1]
Arthur Crimmins during Cyclocrane flight tests in 1984
Two proof of concept versions were built, identical in size and varying in some details. Each had a fabric, oblate spheroid gas bag, or aerostat, to provide aerostatic lift sufficient to support the aircraft and fifty percent of the payload. Airfoils attached to the structure generated forces used to control the airship and to lift the other half of the load. The aerostat contained a rigid internal axle along its long axis. Halfway along the axle, two long beams were fixed at right angles to it and to each other, passing through the aerostat (envelope) where they carried four wings of symmetric airfoil section, or blades as AeroLift termed them. Each blade carried at its tip another, shorter wing mounted with its long axis perpendicular to the plane of the blade, making a T shape. Aerolift termed the blade and wing assembly a "stalk". The stalks could be rotated from their orientation in hover (wherein the blade surfaces were perpendicular to the long axis of the airship and the eventual direction of flight) toward the direction of flight. At the end of the blades, above the wing, were pylons that carried propeller driving engines, oriented at right angles to both wing and blade long axes, so they powered the aircraft forward in normal flight.[1][2]
A "hybrid airship" is defined as an airship that employs two forms of lift; aerostatic and aerodynamic, or buoyancy from gas that is lighter than air and lift from aerodynamic surfaces like wings and rotors. In the Cyclocrane the lighter than air gas, which was either helium or a helium and hydrogen mixture, carried the weight of the aircraft, including fluids and crew, and half the payload. The wings on the ends of the blades generated the lift needed to either carry the rest of the payload or to hold the airship down if it was unloaded. In a two-ton slingload Cyclocrane, for example, (which was the nominal size of the proof of concept models) the lifting gas would lift the weight of the vehicle, fluids and crew and one ton of payload. The wings would produce one ton of force to either lift one ton of payload or to hold the ship down against one ton of buoyancy when the payload was released.
Flights began with the airship either attached to the slingload, or tethered, and allowed to rise until the net buoyancy is transferred to the tether or the load. The "stalk" (the assembly the engine is mounted on) that is hanging beneath the aerostat (the gas bag) is pointed forward and the engine started. The other three stalks are oriented with their blades, wings and engine centerlines perpendicular to the long axis of the airship. Once the lower engine is warmed up and running at full power that stalk is quickly rotated ninety degrees. As soon as the stalk begins to point forward the thrust generated by that engine starts the airship center body into rotation. After a revolution or two the other engine (or engines) are started. When the rate of rotation (in the two ton slingload Cyclocrane) reaches thirteen revolutions per minute the relative wind over the wings, is sixty-miles-per-hour. That airspeed is sufficient to create the lift needed to lift one ton, if the airship is loaded, or to hold the ship down against one ton of buoyancy if it isn't.
To fly to his destination the pilot executes a cyclic command to the wings that causes them to change their orientation through each revolution to either lift the load or counteract the aerostatic lift. Once hovering at the desired altitude a collective command is issued by the pilot to the blades, rotating them toward the direction of flight, causing them to function as propeller blades and pulling the airship forward (or backward). This forward velocity component allows for a reduction in the rate of rotation to maintain the necessary sixty-mile-per-hour relative wind over the wings. The result of this mixing of velocity components means that the path that the wings trace through the air as the ship reaches full forward flight is a helix, the rotation rate decreases as the horizontal speed increases and at full forward flight the ship is no longer rotating.
Cyclocrane flight test – 1984 – Pilot Colonel JJ Morris, Flight Engineers Bill Giordano and Arthur Crimmins
To come to a stop so the load can be released or to moor the airship the process is reversed. The stalks are gradually rotated in the opposite direction causing them to act as a propeller again to take the ship back into rotation and hover. The load is then released and the ship can return for another load or if the ship is to be moored it can be secured to a tether or mast.
Both versions of the CycloCrane were 178ft (54.25 m) long. The first version, completed in 1982 had four piston engines and was fitted with a large, inverted Y-shaped tail needed to stabilise it at its moorings by keeping it pointed into wind. That version was destroyed at its moorings in a storm and was never flown. It was rebuilt by 1984 and fitted with an 18 faceted, ring shaped tail wire braced to the central axis. The aerostats in both versions were 68ft 0 in (20.73 m) in diameter and 136ft 0 in (41.45 m) long and manufactured by ILC Dover of Frederica, Delaware, USA. Partly to save weight, this version had only two engines, a pair of 150hp (112kW) Textron Lycoming AEIO-320 horizontally opposed piston engines driving 4-bladed propellers. This left the CycloCrane rather underpowered, particularly in lift.[1][2]
Cyclocrane Internal components including the longitudinal structure and two of four stalk support struts
The revised CycloCrane began uncrewed flights in August 1984 and made its first crewed flight on October 15, 1984[citation needed] with Colonel JJ Morris as the pilot, Robert Crimmins as co-pilot, Bill Giordano as the flight engineer and Arthur Crimmins as flight engineer and commander. The first untethered flight was made eight days later. By mid-1985 it had accumulated 7 hrs of flight under a US Forest Service contract, but the lack of power limited the spin rate to 10 rpm, rather than the designed 13 rpm so that the aircraft was less nimble in its movements than intended and also only able to lift loads of about half of the target 2 tons.[2] AeroLift received several military contracts in the late 1980s to keep the CycoCrane idea afloat, particularly one from DARPA in 1988 for mooring investigations on a 36ft model and renewal of the proof of concept aircraft for military suitability tests.[1] For its final flights the tail was altered again into a combination of the early inverted Y within the ring of the first rebuild.[3]
When the defense funding ended in 1990, the company ceased to trade.[4]
Specifications (proof of concept vehicle, second version)
Data from Jane's All the World's Aircraft 1989/90 p.671[1]
General characteristics
Length: 178ft 0in (54.25m) overall
Height: 255ft 0in (77.72m) overall, from hook to uppermost engine
An aircraft is a vehicle that is able to fly by gaining support from the air. It counters the force of gravity by using either static lift or the dynamic lift of an airfoil, or, in a few cases, direct downward thrust from its engines. Common examples of aircraft include airplanes, helicopters, airships, gliders, paramotors, and hot air balloons.
A propeller is a device with a rotating hub and radiating blades that are set at a pitch to form a helical spiral which, when rotated, exerts linear thrust upon a working fluid such as water or air. Propellers are used to pump fluid through a pipe or duct, or to create thrust to propel a boat through water or an aircraft through air. The blades are shaped so that their rotational motion through the fluid causes a pressure difference between the two surfaces of the blade by Bernoulli's principle which exerts force on the fluid. Most marine propellers are screw propellers with helical blades rotating on a propeller shaft with an approximately horizontal axis.
An airship, dirigible balloon or dirigible is a type of aerostat or lighter-than-air aircraft that can navigate through the air flying under its own power. Aerostats use buoyancy from a lifting gas that is less dense than the surrounding air to achieve the lift needed to stay airborne.
Flight or flying is the process by which an object moves through a space without contacting any planetary surface, either within an atmosphere or through the vacuum of outer space. This can be achieved by generating aerodynamic lift associated with gliding or propulsive thrust, aerostatically using buoyancy, or by ballistic movement.
The Messerschmitt Me 323 Gigant ("Giant") was a German military transport aircraft of World War II. It was a powered variant of the Me 321 military glider and was the largest land-based transport aircraft to fly during the war. In total, 213 were made, with 15 being converted from the Me 321.
An aerostat is a lighter-than-air aircraft that gains its lift through the use of a buoyant gas. Aerostats include unpowered balloons and powered airships. A balloon may be free-flying or tethered. The average density of the craft is lower than the density of atmospheric air, because its main component is one or more gasbags, a lightweight skin containing a lifting gas to provide buoyancy, to which other components such as a gondola containing equipment or people are attached. Especially with airships, the gasbags are often protected by an outer envelope.
The AEREON III was an experimental hybrid airship of rigid construction built by the AEREON Corporation in the early 1960s. Of unconventional design, the airship featured three gas envelopes attached side-by-side, with the connecting structures shaped as airfoils to create extra lift as the craft moved forward. Intended as a small prototype craft that would precede the development of much larger hybrid airships, the AEREON III was constructed between 1959 and 1965 but was destroyed during taxiing tests in 1966 and scrapped without having flown. It was "the first rigid airship to be built since Graf Zeppelin II".
Aircraft equipped with contra-rotating propellers (CRP) coaxial contra-rotating propellers, or high-speed propellers, apply the maximum power of usually a single piston engine or turboprop engine to drive a pair of coaxial propellers in contra-rotation. Two propellers are arranged one behind the other, and power is transferred from the engine via a planetary gear or spur gear transmission. Contra-rotating propellers are also known as counter-rotating propellers, although the term counter-rotating propellers is much more widely used when referring to airscrews on separate non-coaxial shafts turning in opposite directions.
The Boeing Pelican ULTRA was a proposed ground effect fixed-wing aircraft under study by Boeing Phantom Works in the early 2000s.
A hybrid airship is a powered aircraft that obtains some of its lift as a lighter-than-air (LTA) airship and some from aerodynamic lift as a heavier-than-air aerodyne.
A coaxial-rotor aircraft is an aircraft whose rotors are mounted one above the other on concentric shafts, with the same axis of rotation, but turning in opposite directions (contra-rotating).
Airborne wind energy (AWE) is the direct use or generation of wind energy by the use of aerodynamic or aerostatic lift devices. AWE technology is able to harvest high altitude winds, in contrast to wind turbines, which use a rotor mounted on a tower.
In aeronautics, an aircraft propeller, also called an airscrew, converts rotary motion from an engine or other power source into a swirling slipstream which pushes the propeller forwards or backwards. It comprises a rotating power-driven hub, to which are attached several radial airfoil-section blades such that the whole assembly rotates about a longitudinal axis. The blade pitch may be fixed, manually variable to a few set positions, or of the automatically variable "constant-speed" type.
Metal-clad airships are airships which have a very thin airtight metal envelope, rather than the usual fabric envelope. This shell may be either internally braced as with the designs of David Schwarz, or monocoque as in the ZMC-2. Only four ships of this type are known to have been built, and only two actually flew: Schwarz's aluminum ship of 1893 collapsed on inflation; Schwarz's second airship flew at Tempelhof, Berlin in 1897, landed but then collapsed; the ZMC-2 flew 752 flights between 1929 and scrapping in 1941; while the Slate City of Glendale, was built in 1929 but never flew.
Aeros Corp is an American manufacturer of airships based in Los Angeles, California. It was founded in 1993 by the current CEO and Chief Engineer, Igor Pasternak, who was born in Soviet Kazakhstan, raised in Soviet Ukraine, and moved to the U.S. after the Soviet collapse to build airships there. It currently employs more than 100 workers.
The Piasecki PA-97 Helistat was an American experimental heavy-lift aircraft, built by Piasecki by fastening four H-34J helicopters to a framework beneath a helium-inflated blimp envelope. The sole prototype was lost during a test flight, killing a test pilot and injuring another four in the course of a single incident.
The static buoyancy of airships in flight is not constant. It is therefore necessary to control the altitude of an airship by controlling its buoyancy: buoyancy compensation.
The Hybrid Air Vehicles Airlander 10 is a hybrid airship designed and built by British manufacturer Hybrid Air Vehicles (HAV). Comprising a helium airship with auxiliary wing and tail surfaces, it flies using both aerostatic and aerodynamic lift and is powered by four diesel engine-driven ducted propellers.
An aerostat is an aircraft that remains aloft through the use of lighter-than-air gases. A narrower and more technical meaning refers only to tethered balloons.
A cyclorotor, cycloidal rotor, cycloidal propeller or cyclogiro, is a fluid propulsion device that converts shaft power into the acceleration of a fluid using a rotating axis perpendicular to the direction of fluid motion. It uses several blades with a spanwise axis parallel to the axis of rotation and perpendicular to the direction of fluid motion. These blades are cyclically pitched twice per revolution to produce force in any direction normal to the axis of rotation. Cyclorotors are used for propulsion, lift, and control on air and water vehicles. An aircraft using cyclorotors as the primary source of lift, propulsion, and control is known as a cyclogyro or cyclocopter. A unique aspect is that it can change the magnitude and direction of thrust without the need of tilting any aircraft structures. The patented application, used on ships with particular actuation mechanisms both mechanical or hydraulic, is named after German company Voith Turbo.
References
1 2 3 4 5 Taylor, John W R (1989). Jane's All the World's Aircraft 1989–90. Coulsdon: Jane's Information Group, Ltd. pp.670–1. ISBN0-7106-0896-9.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
