Altec Lansing Duplex

Last updated
Altec 604 Duplex Loudspeaker Altec 604 Duplex Loudspeaker.jpg
Altec 604 Duplex Loudspeaker
Original Altec 604 Sales Literature, Page 1 Original Altec 604 Sales Literature, Page 1.jpg
Original Altec 604 Sales Literature, Page 1
Cutaway View Of Altec 604 Duplex Loudspeaker Cutaway View Of Altec 604 Duplex Loudspeaker.jpg
Cutaway View Of Altec 604 Duplex Loudspeaker
Comparison of the different horns used in the Altec 604 and 604B and the one used in the 604C-G Altec 604 Horn Comparisons - B Horn vs C-G Horn.jpg
Comparison of the different horns used in the Altec 604 and 604B and the one used in the 604C-G
Altec 605A Advertisement, 1959 Altec 605A Advertisement, 1959.jpg
Altec 605A Advertisement, 1959
Altec 604E SuperDuplex Specification Sheet, Page 1 Altec 604E SuperDuplex Specification Sheet, Page 1.jpg
Altec 604E SuperDuplex Specification Sheet, Page 1
Altec Lansing 604-8K Duplex Loudspeaker Altec Lansing 604-8K Duplex Loudspeaker.jpg
Altec Lansing 604-8K Duplex Loudspeaker
Current version of the Altec 604 GPA 604-8H-II Duplex Loudspeaker.jpg
Current version of the Altec 604

DUPLEX was the trade name given by Altec Lansing to its line of coaxial loudspeakers, beginning with the first model 601 in 1943. However, the name was most commonly associated with the subsequent model 604 which was a seminal loudspeaker that became a milestone in loudspeaker development. Well over a dozen different models carried the Duplex name over a near 50-year period. The vast majority consisted of a high frequency (HF) compression driver mounted to the back of a large diameter (12–15 in) paper cone low frequency (LF) driver. However, there were also a few models with small diameter LF cones and direct radiator tweeters.

Contents

The Duplex speakers were extremely versatile with the 604 model alone finding application in studio monitoring, home high fidelity, public address, tour sound reinforcement, cinema sound and installed sound. A number of duplex drivers were developed for very specialized applications, such as ceiling speakers. Some of the more significant models in the Duplex lineup were, in order of introduction, the 15" 601, 15" 604, 15" 602, 12" 601, 15" 605, 15" 904 and 12" 920.

The significance of the Duplex loudspeakers is evidenced by the fact that the Altec Lansing 604 Duplex was inducted into the TECnology Hall of Fame in 2005. [1]

Altec 601

The path to the Duplex line started with the acquisition of the Lansing Manufacturing Company (LMCO) in 1941 by the All Technical Products Company. At that time, the company name was shortened to "Altec" and "Lansing" was added at the same time, creating Altec Lansing, commonly called, simply, "Altec". That acquisition brought Altec into the loudspeaker manufacturing business and brought the loudspeaker manufacturing capabilities of its principal, James B. Lansing. Shortly after that, Altec was approached by one of its dealers, named Art Crawford, with a request to develop a compact loudspeaker. Crawford was a high-end audio dealer in Los Angeles at the time, and he felt that there was a viable market for a high-quality loudspeaker that was small enough to be used in home audio systems. The current two-way speakers with separate LF and HF drivers were too large for this application and Art suggested a coaxial design whereby a LF and HF driver could be combined into one unit. Altec's president and owner, George Carrington, Sr., saw the merit of this concept. Carrington, an audio engineer himself, designed the prototype, assisted by John Hilliard, who did the crossover design, and Jim Lansing, who developed the tooling for the project and supervised its construction. [2]

By 1943, a prototype was rapidly developed with off-the-shelf LMCO components. The LF portion of the driver was developed by taking the field coil motor from the LMCO 287 compression driver and using it to drive the cone from one of LMCO's 15-inch LF drivers with a 2-inch voice coil. Both were mounted on a stamped steel frame. An LMCO 801 field coil compression driver with a 1.75-inch diaphragm was used as-is for HF reproduction and mounted coaxially to the back of the 287 motor. A horn throat from the 801 penetrated the center of the LF field coil and exited into a small multicellular horn mounted in front of the LF cone. The horn was designed with a cut-off frequency of 900 Hz and the system was set with a crossover frequency of 1200 Hz.

The prototype confirmed the concept and went into production in 1943 as the model 601 Duplex, but it was not long-lived. In less than a year, a significant redesign was underway to substantially improve the driver. The primary motivation was to replace the field coil motors with permanent magnet motors. Field coils are very powerful allowing for very efficient loudspeakers. However, they require an external power supply which greatly limits their areas of application.

When the 601 was first designed, there were no commercially available permanent magnets that could cost effectively provide the same level of magnetic energy as a field coil. During WWII, Altec was involved in developing submarine detection equipment for the Marine Airborne Detection program. It was through this that they were introduced to a new type of permanent magnetic material; Alnico V. This was much stronger than any other permanent magnet at the time. In 1944, they used this technology to create a permanent magnet version of the 601 the which became the famous 604.

There has been much confusion about the original 601 due to the fact that very few were made, with almost no survivors, and because the model name was re-used in the 1950s for a completely different Altec Lansing Duplex driver. The 1950s version of the 601 was a 12" diameter coaxial speaker with a miniature HF compression driver mounted within the motor of the LF driver using permanent magnets. This confusion was exacerbated in 1988 when Altec Lansing misidentified the later 12" 601 as the original 601 in their own promotional literature celebrating their 50th anniversary. That mistake was carried forth for years in subsequent Altec Lansing literature. However, at least one original field coil 601 is known to exist (S/N 150) and has been confirmed as a 15" model. [3] In addition, copies of the original sales literature exist that accurately describe it. [4]

Altec 604

The permanent magnet upgrade of the 601 was released in 1944 as the 604, at which point the 601 was discontinued. [5] The 604 was the same basic design using a 15-inch LF driver, but with a larger 3" voice coil, individual Alnico V magnets for the LF and HF drivers, and a cast aluminum frame.

When making the horn for the 601/604, it had to be designed so the sound coming from it would not interfere with the sound from the bass driver. To overcome this, a 2×3 multicellular design with a dispersion of 40°×90° was used. This allowed the sound to leave the horn and be dispersed largely without coming into contact with the cone of the bass driver. The backside of the horn, which faced the LF cone, was also coated with a damping compound to reduce high frequency reflections off of it. The first 604 had a crossover frequency of 2000 Hz.

Both the 601 and the first 604 had a frequency response of 60 Hz to 16 kHz with a power rating of only 25 watts, relatively low but acceptable due to the speakers' efficiency. As amplifiers of the time did not produce much power, the speakers had to be extremely efficient to produce adequate loudness. The next speaker in the 604 line to be released was the 604B, with a slightly higher power handling at 30 watts and a better frequency response ranging from 30 Hz to 16 kHz. Also, this speaker had a lower crossover frequency of 1000 Hz.

Following the 604B came the 604C. Again, the power handling capacity and frequency response were increased to 35 watts and 30 Hz to 22 kHz, respectively. The 604C was the first version of the 604 to use the redesigned HF horn. Alexis Badmaieff, head of acoustic engineering at Altec at the time, changed the horn design from a true multicellular type to what was really a sectoral horn with "fins" inside the bell flare. The fins did not go all the way back to the opening of the throat of the horn, as did the previous design. A young Paul S. Veneklasen, who was working in the acoustic research department at Altec at the time, objected to the change, claiming that it was done to save money, not because it was an acoustical improvement. His protestations went unheeded and the sectoral horn with the "fins", or as some called them, "vanes", remained in use in the 604, starting with the "C" version and continuing through the "G". [6]

Following the 604C came the short-lived 604D, which was soon replaced with the 605A. The 605A was supposed to be an improvement over the 604, but it was poorly received, partly because it was an attempt to make it cheaper to build the 604, but mostly because the name, "604", had become a widely recognized industry standard, and people didn't WANT a 605 – they wanted a 604. So, Altec relented and released the 604E SuperDuplex.

The 604-8G was next, and was released in 1973. It was produced until 1979, and was the last using the "C-style HF horn. The power handling capacity was substantially increased to 65 watts and the frequency response was improved, bringing the bass response down to 20 Hz and treble response up to 22 kHz.

The next big step in the 604 family was the 604-8K, which was similar in most respects to the 604-8G, but used a ferrite magnet instead of an Alnico V magnet. Ferrite magnets are much more resistant to being demagnetized and are thus more robust. However, debate continues to this day as to the sonic superiority of Alnico V vs ferrite magnetic motors as it relates to freedom from distortion. Also, the 604-8K used a new HF horn design based on Altec's new, patented MANTARAY series of horns, rather than the multicellular horn design of the older models. It also used Altec's new TANGERINE radial phasing plug, which greatly improved the HF performance. The Mantaray horn was a marked improvement over the C-G HF horn, but still did not have the dispersion qualities and low-frequency loading of the original multicellular horn.

The 604 achieved its greatest fame as a recording studio monitor. Its compact size, wide bandwidth, high output and point source topology made it an ideal choice for the needs of the new tape recording technology introduced in the late '40s and early '50s. Prior to tape recorders, commercial recordings were cut directly to a master disk, nominally in one take with no real provision for editing. As a result, monitoring needs were very rudimentary and mainly regarded monitoring for technical defects.

In contrast, the tape recorder ushered in editing, overdubbing and ultimately multi-track recording and stereo output. There was the continuing need to critically listen to recordings long after the performance was captured to accommodate the substantial post processing now required to develop a final master tape. At the time, the 604 was unequalled in this application, given the significant increase in accuracy it presented over the competition. As a result, it became ubiquitous in North American recording studios for the next two decades. In the 1970s it was overtaken by competition, primarily from JBL. However, later that same decade, it would have a resurgence that lasted well into the 1980s when UREI introduced their 813 studio monitor that incorporated a modified 604 driver with a time-aligned cross-over. For a time, the 813 was nearly as ubiquitous as the original 604.

Altec 904

Shortly after the introduction of the 604-8K, Altec released the 904-8A, which was basically a high powered 604-8K that could handle up to 150 watts. Both remained in production until the shutdown of Altec Lansing Professional by its then owners, Telex Communications, in 1998.

Current manufacture

In 1998, Altec Lansing was closed by its parent company, Telex Corporation. At that time, William Hanushak, who worked for Altec in the manufacture and design of loudspeakers, purchased the tooling and rights to manufacture parts and products formerly produced by Altec Lansing, including the 604-series. For a while, his company, Great Plains Audio, produced the 604-8K. However, dissatisfied with the MANTARAY horn, Bill began working on a new version of the 604 – the 604-8H. The 604-8H featured the horn used on the UREI version of the 604 in the '70s, minus the blue foam, which, after testing, was found unnecessary. The current version is the 604-8H-III, [7] and an Alnico version with the true multicellular horn is available by special order.

Related Research Articles

<span class="mw-page-title-main">Subwoofer</span> Loudspeaker for low-pitched audio frequencies

A subwoofer is a loudspeaker designed to reproduce low-pitched audio frequencies, known as bass and sub-bass, that are lower in frequency than those which can be (optimally) generated by a woofer. The typical frequency range that is covered by a subwoofer is about 20–200 Hz for consumer products, below 100 Hz for professional live sound, and below 80 Hz in THX-certified systems. Thus, one or more subwoofers are important for high-quality sound reproduction as they are responsible for the lowest two to three octaves of the ten octaves that are audible. This very low-frequency (VLF) range reproduces the natural fundamental tones of the bass drum, electric bass, double bass, grand piano, contrabassoon, tuba, in addition to thunder, gunshots, explosions, etc.

<span class="mw-page-title-main">Loudspeaker</span> Converts an electrical audio signal into a corresponding sound

A loudspeaker is an electroacoustic transducer that converts an electrical audio signal into a corresponding sound. A speaker system, also often simply referred to as a speaker or loudspeaker, comprises one or more such speaker drivers, an enclosure, and electrical connections possibly including a crossover network. The speaker driver can be viewed as a linear motor attached to a diaphragm which couples that motor's movement to motion of air, that is, sound. An audio signal, typically from a microphone, recording, or radio broadcast, is amplified electronically to a power level capable of driving that motor in order to reproduce the sound corresponding to the original unamplified electronic signal. This is thus the opposite function to the microphone; indeed the dynamic speaker driver, by far the most common type, is a linear motor in the same basic configuration as the dynamic microphone which uses such a motor in reverse, as a generator.

<span class="mw-page-title-main">Tweeter</span> Type of loudspeaker

A tweeter or treble speaker is a special type of loudspeaker that is designed to produce high audio frequencies, typically deliver high frequencies up to 100 kHz. The name is derived from the high pitched sounds made by some birds (tweets), especially in contrast to the low woofs made by many dogs, after which low-frequency drivers are named (woofers).

A woofer or bass speaker is a technical term for a loudspeaker driver designed to produce low frequency sounds, typically from 20 Hz up to a few hundred Hz. The name is from the onomatopoeic English word for a dog's deep bark, "woof". The most common design for a woofer is the electrodynamic driver, which typically uses a stiff paper cone, driven by a voice coil surrounded by a magnetic field.

<span class="mw-page-title-main">Horn loudspeaker</span> Loudspeaker using an acoustic horn

A horn loudspeaker is a loudspeaker or loudspeaker element which uses an acoustic horn to increase the overall efficiency of the driving element(s). A common form (right) consists of a compression driver which produces sound waves with a small metal diaphragm vibrated by an electromagnet, attached to a horn, a flaring duct to conduct the sound waves to the open air. Another type is a woofer driver mounted in a loudspeaker enclosure which is divided by internal partitions to form a zigzag flaring duct which functions as a horn; this type is called a folded horn speaker. The horn serves to improve the coupling efficiency between the speaker driver and the air. The horn can be thought of as an "acoustic transformer" that provides impedance matching between the relatively dense diaphragm material and the less-dense air. The result is greater acoustic output power from a given driver.

<span class="mw-page-title-main">JBL</span> American audio hardware manufacturer

JBL is an American audio equipment manufacturer headquartered in Los Angeles, California, United States. JBL serves the customer home and professional market. The professional market includes studios, installed/tour/portable sound, music production, DJ, cinema markets. The home market includes high-end home amplification/speakers/headphones as well as high-end car audio. JBL is owned by Harman International, itself a subsidiary of Samsung Electronics.

Altec Lansing, Inc. is an American audio electronics company founded in 1927. Their primary products are loudspeakers and associated audio electronics for professional, home, automotive and multimedia applications.

Thiele/Small parameters are a set of electromechanical parameters that define the specified low frequency performance of a loudspeaker driver. These parameters are published in specification sheets by driver manufacturers so that designers have a guide in selecting off-the-shelf drivers for loudspeaker designs. Using these parameters, a loudspeaker designer may simulate the position, velocity and acceleration of the diaphragm, the input impedance and the sound output of a system comprising a loudspeaker and enclosure. Many of the parameters are strictly defined only at the resonant frequency, but the approach is generally applicable in the frequency range where the diaphragm motion is largely pistonic, i.e., when the entire cone moves in and out as a unit without cone breakup.

<span class="mw-page-title-main">Full-range speaker</span> Type of loudspeaker

A full-range loudspeaker drive unit is defined as a driver which reproduces as much of the audible frequency range as possible, within the limitations imposed by the physical constraints of a specific design. The frequency range of these drivers is maximized through the use of a whizzer cone and other means. Most single driver systems, such as those in radios, or small computer speaker designs, cannot reproduce all of the audible frequencies or the entire audible audio range.

The chief electrical characteristic of a dynamic loudspeaker's driver is its electrical impedance as a function of frequency. It can be visualized by plotting it as a graph, called the impedance curve.

<span class="mw-page-title-main">Loudspeaker enclosure</span> Acoustical component

A loudspeaker enclosure or loudspeaker cabinet is an enclosure in which speaker drivers and associated electronic hardware, such as crossover circuits and, in some cases, power amplifiers, are mounted. Enclosures may range in design from simple, homemade DIY rectangular particleboard boxes to very complex, expensive computer-designed hi-fi cabinets that incorporate composite materials, internal baffles, horns, bass reflex ports and acoustic insulation. Loudspeaker enclosures range in size from small "bookshelf" speaker cabinets with 4-inch (10 cm) woofers and small tweeters designed for listening to music with a hi-fi system in a private home to huge, heavy subwoofer enclosures with multiple 18-inch (46 cm) or even 21-inch (53 cm) speakers in huge enclosures which are designed for use in stadium concert sound reinforcement systems for rock music concerts.

<span class="mw-page-title-main">Studio monitor</span> Speaker designed to reproduce sound accurately

Studio monitors are loudspeakers in speaker enclosures specifically designed for professional audio production applications, such as recording studios, filmmaking, television studios, radio studios and project or home studios, where accurate audio reproduction is crucial. Among audio engineers, the term monitor implies that the speaker is designed to produce relatively flat (linear) phase and frequency responses. In other words, it exhibits minimal emphasis or de-emphasis of particular frequencies, the loudspeaker gives an accurate reproduction of the tonal qualities of the source audio, and there will be no relative phase shift of particular frequencies—meaning no distortion in sound-stage perspective for stereo recordings. Beyond stereo sound-stage requirements, a linear phase response helps impulse response remain true to source without encountering "smearing". An unqualified reference to a monitor often refers to a near-field design. This is a speaker small enough to sit on a stand or desk in proximity to the listener, so that most of the sound that the listener hears is coming directly from the speaker, rather than reflecting off walls and ceilings. Monitor speakers may include more than one type of driver or, for monitoring low-frequency sounds, such as bass drum, additional subwoofer cabinets may be used.

<span class="mw-page-title-main">Guitar speaker</span>

A guitar speaker is a loudspeaker – specifically the driver (transducer) part – designed for use in a combination guitar amplifier of an electric guitar, or for use in a guitar speaker cabinet. Typically these drivers produce only the frequency range relevant to electric guitars, which is similar to a regular woofer type driver, which is approximately 75 Hz — 5 kHz, or for electric bass speakers, down to 41 Hz  for regular four-string basses or down to about 30 Hz for five-string instruments.

<span class="mw-page-title-main">Moving iron speaker</span>

The moving iron speaker was the earliest type of electric loudspeaker. They are still used today in some miniature speakers where small size and low cost are more important than sound quality. A moving iron speaker consists of a ferrous-metal diaphragm or reed, a permanent magnet and a coil of insulated wire. The coil is wound around the permanent magnet to form a solenoid. When an audio signal is applied to the coil, the strength of the magnetic field varies, and the springy diaphragm or reed moves in response to the varying force on it. The moving iron loudspeaker Bell telephone receiver was of this form. Large units had a paper cone attached to a ferrous metal reed.

<span class="mw-page-title-main">John Kenneth Hilliard</span> American engineer

John Kenneth Hilliard was an American acoustical and electrical engineer who pioneered a number of important loudspeaker concepts and designs. He helped develop the practical use of recording sound for film, and won an Academy Award in 1935. He designed movie theater sound systems, and he worked on radar as well as submarine detection equipment during World War II. Hilliard collaborated with James B. "Jim" Lansing in creating the long-lived Altec Voice of the Theatre speaker system. Hilliard researched high-intensity acoustics, vibration, miniaturization and long-line communications for NASA and the Air Force. Near the end of his career, he standardized noise-control criteria for home construction in California, a pattern since applied to new homes throughout the U.S.

<span class="mw-page-title-main">Electrodynamic speaker driver</span> Individual transducer that converts an electrical audio signal to sound waves

An electrodynamic speaker driver, often called simply a speaker driver when the type is implicit, is an individual transducer that converts an electrical audio signal to sound waves. While the term is sometimes used interchangeably with the term speaker (loudspeaker), it is usually applied to specialized transducers which reproduce only a portion of the audible frequency range. For high fidelity reproduction of sound, multiple loudspeakers are often mounted in the same enclosure, each reproducing a different part of the audible frequency range. In this case the individual speakers are referred to as drivers and the entire unit is called a loudspeaker. Drivers made for reproducing high audio frequencies are called tweeters, those for middle frequencies are called mid-range drivers, and those for low frequencies are called woofers, while those for very low bass range are subwoofers. Less common types of drivers are supertweeters and rotary woofers.

A coaxial loudspeaker is a loudspeaker system in which the individual driver units radiate sound from the same point or axis. Two general types exist: one is a compact design using two or three speaker drivers, usually in car audio, and the other is a two-way high-power design for professional audio, also known as single-source or dual-concentric loudspeakers. The design is favored for its compactness and behavior as an audio point source.

The Wharfedale MACH series of loudspeakers consists of the MACH 3, 5, 7, and 9. This is an informational page devoted to owners and users of these loudspeakers and those interested in history and construction of electronic sound reproduction.

<span class="mw-page-title-main">Clifford A. Henricksen</span> American inventor, American musician

Cliff Henricksen is a musician, inventor and audio technologist. He is self-taught as a musician with a graduate degree in mechanical engineering at Massachusetts Institute of Technology (MIT). Throughout his career Cliff has found innovative ways to apply engineering basics to electro acoustics and to audio technology as it applies to music and in particular to live music performance. He has invented and engineered a wide variety of technologies and products well known in the world of professional audio. Today he balances work in audio and work as a performing musician.

<span class="mw-page-title-main">Charlie Hughes (audio engineer)</span> American inventor and audio engineer (born 1965)

Charles Emory Hughes II is an American inventor and audio engineer. He is known for his work on loudspeaker design, and the measurement of professional audio sound systems. Hughes first worked for Peavey Electronics designing loudspeakers and horns where he was granted a patent for the Quadratic-Throat Waveguide horn used in concert loudspeakers. He worked for Altec Lansing for two years as chief engineer for the pro audio division and was granted two more patents. In 2021, Hughes was hired by Biamp as principal engineer.

References

  1. "1944 Altec Lansing 604 Duplex Speaker". Mix. September 1, 2006. Archived from the original on 2013-01-18. Retrieved June 26, 2013.
  2. Personal letter from the late Alvis A. Ward, former President and Chairman of the Board, Altec Corporation, to Todd W. White, 1990.
  3. "Altec 601 Duplex Surviving Example". Lansing Heritage. Retrieved 24 March 2016.
  4. "Altec 601 Duplex Specification". Lansing Heritage. Retrieved 24 March 2016.
  5. alteclansingunofficial.nlenet.net
  6. Personal letter from the late Dr. Paul S. Veneklasen to Todd W. White, 1992.
  7. "Products".