AMAL was a British engineering company servicing the motorcycle and other light-engineering motor industries between 1927 and 1993[1] based in Birmingham, England.[2]
AMAL is a British carburettor trademark. Amal was the supplier of carburettors to many marques within the British motorcycle industry[3] including the largest of British manufacturers, such as Triumph, BSA and AMC, and to producers of small industrial engines.
The main carburettor types commonly associated with Amal are slide carburettors for motorcycles. These were historically distinguishable as three types: the Standard, with a separate float chamber, the Monobloc with an integral but offset float chamber and the Concentric, a later development with the float chamber directly below the body and air-slide.
Less-common types, known as GP and TT, were mainly for road-racing and other competition use, and were used on high-performance road machines such as BSA Gold Star, BSA Spitfire and Velocette Thruxton.
Amal also produced handlebars and control levers for the motorcycle industry,[2] via a subsidiary business, Lozells Engineering,[4] twist grips,[5] cables and wire, plus ICIsilicone grease.[3][6] All AMAL chromium plated components were stated to be finished in "Nickel Chromium Plating, British Standard Approved."[3]
Amal's light-alloy levers with click-stop adjusters 509/001 brake and 509/002 clutch were taken-over by BSA and marketed under their 'Motoplas' accessories branding from 1967, with Doherty taking-over production of the traditional chromed-steel levers.[7]
With the decline of the British motorcycle industry, the use of Amal carburettors declined, but they are still produced under different ownership as spares for the classic market.
Carburettor products
Besides carburettors for light-applications such as types 308 and 355 for Pedal Cycle Motors,[8] Amal historically had three popular carburettor designs: 'Standard' fitted up to 1955, 'Monobloc' fitted from 1955 and 'Concentric' fitted from 1967.[9]
The most historic - 76 & 276 Series (Amal 'Standard' series) can be spigot or flange fixing with adjustment screws on the left or right hand sides of the carburetter body. The available bore sizes are 15/16", 1" and 1 1/16" diameters. The 276 type carburettor is, in virtually all aspects, identical to the 76 version, except that the main emulsion air is drawn from inside the air intake (air filter) whilst the 76 carburettor uses unfiltered air. The 76 types are of die-cast zinc construction and were introduced in the early 1930s, replacing the earlier 6 series, which were of bronze construction, although basically the same design. The 276 type was introduced in 1940 in an attempt to improve the carburettor's durability in dusty and dirty operating environments.
In the same design range were the 4 and 5 types with smaller bore sizes and the 29 type with larger bore sizes. These were replaced with the 74, 75 and 89 and then, later, by the 274, 275 and 289 types.
The 'Monobloc' type was available from 1955 with designations 375, 376 and 389[9]
The more modern Concentric, developed and introduced for the 1967 Model Year, was initially designated 600 and 900.[2] The 600 series had bore sizes of 22mm, 24mm and 26mm, being known as 622, 624, and 626 respectively. Similarly, the 900 series with bore sizes of 28mm, 30mm and 32mm, were known as 928, 930, and 932 respectively.[10]
The largest bore at 32mm was slightly larger than any previous Monobloc, and all were flange-fitting with stud-holes at two-inch centres.[10]
The Concentric design with non-protruding float chamber was both slimmer and shorter, enabling easier mounting to two-port cylinder heads. Left or right sided carburettors could be produced from basically the same die-casting, and the design was compatible with up to 40 degrees of downdraught.[10]
Eventually three variants were produced: Mk1, Mk1.5 and Mk2.
'Standard' series
Amal type 276 carburettor fitted to a 1951 BSA B31 350cc
Following the merger of Amac, Brown and Barlow, and Binks to form Amal, a new range of carburettors were introduced in 1929, the 'Standard' range. The body of these carburettors was cast in bronze and the other components made of brass.[11] The float chamber was manufactured as a separate unit and attached to the carburettor by an arm.[12] To mount the carburettor to the engine, the carburettors were available in both flange and spigot options.[13] Four body sizes were available:
The sand cast body was expensive to produce and limited production throughput. To reduce production costs and time, die castzinc alloy bodies were introduced in 1932. These were designated types 74, 75, 76 and 89 and were virtually identical to the previous types, most of the components were interchangeable.[14]
Ingress of dust and dirt caused premature wear to the carburettor, which was partially resolved by fitting air filters. The idle and air bleed circuits still drew air from outside the body which led to blocked jets and tubes. To overcome this types 274, 275, 276 & 289 were introduced in 1939 which took the air feeds from the incoming filtered airflow.[15]
Monobloc
Amal 376 Monobloc carburettor fitted to a 1958 BSA A10 Golden FlashChopped Amal Monobloc carburettors and remote float chamber fitted to a 1958 Triumph T120 Bonneville 650cc
Introduced in 1954, the Monobloc was introduced to reduce production cost. Whilst the design relied heavily on the previous standard series, the float chamber had been combined into the carburettor casting. The jet block and slide had been simplified and a removable pilot jet introduced instead of the drilling on the Standard models. This allowed a common jet block to be used on different models. Three sizes were introduced:[16]
Type 375 - 21/32", 23/32", 25/32", 13/16" and 7/8" bore diameters, replacing the 274 and 275 standard types
Type 376 - 15/16", 1" and 1 1/16" bore diameters, replacing the 276 standard types
Type 389 - 1 1/8", 1 5/32" and 1 3/16" bore diameters, replacing the 289 standard types
The 375 was also available with a cast in air filter in 25/32" and 13/16" bore diameters. These were designated type 363.[17]
All Monoblocs were initially manufactured with the float chamber projecting on the left side of the body when viewed from the air intake. This led to fitment problems on twin carb installation. Amal introduced a "chopped" version of the 376 and 389 without the float chamber so twin carburettors could be fitted. Both carbs were fed from the float chamber of the left hand carb.[16]Triumph twins used two chopped monoblocs and a remote float chamber mounted centrally behind the carbs.[18][19] In 1964 a right hand version of the 389 was introduced, designated 689, which was a mirror image of the 389. This allowed twin carb installations with each carb having its own float chamber.[16]
Production ended in 1967 when the Concentric was introduced.[16] The Monobloc was reintroduced in 2014, the 375 body being cast in aluminium alloy.[20] Replacement hard anodised slides to reduce wear were made available.[21]
Concentric
Mark 1
Amal Concentric carburettor, one of two fitted to a Triumph Bonneville, with the second just visible to the rear
To reduce the technical and manufacturing problems of previous carbs and with pending emission controls requiring more accurate fuel metering, a new carburettor, the Concentric, was introduced for the 1968 model year. A hemispherical float chamber was introduced below and concentric with the main jet to eliminate differences in fuel height during cornering. There was no jet block, the jets being mounted directly into the body. The pilot jet reverted to a drilling instead of a removable jet. Right and left hand carburettors were available with flange mountings only.[22]
To satisfy the demand for larger carburettors the 1000 series was introduced in 1970 with bore sizes of 34, 36 and 38mm.[23]
The British motorcycle industry was in decline and with the lack of orders for OEM carburettors, production was limited after 1975 for replacement and aftermarket sales. Following the introduction of other models of the Concentric, this model became known as the Mark 1.[22]
Premier
An updated version of the Mark 1, the Premier, was introduced in 2012. The castings for the body and float bowl were in aluminium alloy and the slide was made of hard anodised aluminium. A new float was introduced that was resistant to the ethanol in modern fuels. The pilot jet was removable. and the idle circuit improved.[24][25]
Mark 1.5
To supply demand for OEM carburettors for Spanish made motorcycles, Amal licensed Talleres Arreche to produce carburettors in Spain. Initially this production was of 400, 600 and 900 series Concentrics. The Spanish motorcycle manufacturers required a better cold starting system so Amal and Talleres Arreche jointly designed modifications to the concentric to provide a separate enrichment circuit. These carburettors,[26] introduced in 1973,[27] were available in both flange and spigot mountings to suit the Spanish manufacturers requirements. To distinguish this variant from the British made version, they became known as Mark 1.5 or Mark 1 1/2 and a 1 prefix added to the product number, for example the modified 626 became the 1626.[26]
A derivative of the 400 series is still in production by Talleres Arreche in 16, 18 and 20 mm bores with Amal embossed on the body.[28]
Mark 2
Introduced in 1974,[29] the Mark 2 used aluminium alloy for the main castings rather than the zinc alloy previously used. The cold starting system from the Mark 1.5 was integrated into the new design. Whilst the float chamber was still concentric with the main jet, it was now a square section. The pilot jet reverted to being removable and could be inserted in an alternate position for higher downdraught applications. Flange mounting was discontinued and the Mark 2 was only available in spigot mounting.[30]
Three body sizes were available:
2600 series - 22, 24, 25, 26 and 27mm bore diameters
The Type 27 was Amal's first carburettor specifically designed for racing machines,[31] and was based on AMAC's TT carburettor that had been introduced in 1924.[32] A jet block and hollow slide were used. The body, jet block and slide were assembled and then machined as one unit to ensure perfect matching and unobstructed flow through the carburettor. No needle or needle jets were fitted. For starting a pilot jet and bypass were used. To reduce fuel surge when cornering, two float chambers were used with the 27, one mounted on either side of the carb.[31][33]
The TT (Series 27) was introduced in 1932 as a progression of the Type 27. A needle and needle jet were incorporated to provide additional tuning for road machines and when the carb was used with alcohol as a fuel. Pre-war models were suffixed with the year of manufacture but when production resumed after WW2, all of the TTs had a 9 suffix regardless of year.[34]
As well as the spigot mounting as used by the Type 27, flange fixing was introduced. As the spigot mountings were susceptible to air leaks, flange mounting was seen as an improvement.[34]
Sales of the 25TT were small and the model was discontinued in 1934. Production of the other two versions continued to 1954.[36]
RN
The RN (Series 185) was introduced in 1937 as a development of the TT. The needle and jets were moved to the side of the carburettor bore to give a less obstructed flow through the carburettor, although this caused a complicated attachment of the needle to the slide. Although at the time the less restricted flow was seen as an advantage, later opinion was less positive.[36]
Initial the RN was designated as a type of TT, eg 10TT37KN, but soon it was given its own type reference, eg 10RN. It was available in the same sizes as the 10TT and 15TT. This type was less popular than its parent TT. Production ended with the introduction of the GP in 1954.[36]
GP
Amal GP carburettor fitted to a 1956 BSA Gold Star 500cc
The GP (Series 316) was introduced in 1954 replacing both the TT and RN,[32] and was a further development of the RN. Although the needle and jets were still offset, they were moved away from the side of the bore which simplified the needle mounting. Air for the pilot feed was taken from the outside of the carb through a drilling. The GP was available in four body sizes and in flange mounting only:[37]
Initially the GP was produced in zinc alloy but in the late 1950s the material was changed to aluminium ally.[38]
The GP suffered from pilot systems, partly due to dust and dirt entering through the air drilling. The pilot system also limited the carb from being used with more than 20° downdraft otherwise flooding of the pilot circuit occurred.[38]
GP2
The GP2 series was introduced in 1962 to try to overcome the shortcomings of the GP. The pilot circuit was moved to the inlet side if the slide. The air bleed was taken from the incoming air rather than the outside, reducing the possibility of dirt ingress to the circuit. The moving of the pilot jet allowed far greater downdraught angles without the jet flooding.[32][39]
The GP2 was available in the same sizes as the original GP.[27][32]
Mark 2 Smoothbore Concentric
A smoothbore version of the 2000 series Mark Concentric was made available for racing used. To obtain the "smoothbore", a jet block and hollow slide were fitted. Although the carb was never used as an OEM part, it was popular with smaller specialist racers.[27]
Company history
The AMAL company was formed in the late 1920s when three manufacturers amalgamated – Amac, Brown and Barlow, and Binks – to manufacture carburettors and associated products under the name Amalgamated Carburetters Ltd.[1]
The name changed to Amal Ltd in 1931.[1] Amal subsequently became partly owned by IMI Group, and the product range was expanded to include handlebars and controls with full IMI ownership by the middle 1960s.[1] It was sold after June 1973[40] to Grosvenor Works Ltd of North London - a supplier of fuel system components. Under Grosvenor some of the most popular obsolete ranges were remanufactured.[1]
In 2003, the business was sold to Burlen Fuel Systems Limited, a company that also produces SU, Solex and Zenith, three other classic carburettor ranges.
Amal carburettors were used on Cooper Formula 3 racing cars and racing motor cycles. Coopers fitted with the J.A.P. 1,100cc engine with such a carburettor were popular in hill climbs and sprints competitions, and were used by the frequent champion in the 1960s, David Boshier Jones.[41][pageneeded]
Related Research Articles
A carburetor is a device used by a gasoline internal combustion engine to control and mix air and fuel entering the engine. The primary method of adding fuel to the intake air is through the Venturi tube in the main metering circuit, though various other components are also used to provide extra fuel or air in specific circumstances.
The Zenith Carburetter Company Limited was a British company making carburettors in Stanmore Middlesex, founded in 1912 as a subsidiary of the French Société du carburateur Zénith. In 1965, the company joined with its major pre-war rival Solex Carburettors, and over time, the Zenith brand name fell into disuse. The rights to the Zenith designs were owned by Solex UK.
Weber Carburetors is an automotive manufacturing company founded in 1923, known for their carburetors.
The Suzuki GSX-R750 is a sports motorcycle made by Suzuki since 1984. It was introduced at the Cologne Motorcycle Show in October 1984 as a motorcycle of the GSX-R series for the 1985 model year.
The Triumph Bonneville is a standard motorcycle featuring a parallel-twin four-stroke engine and manufactured in three generations over three separate production runs.
The Kawasaki Ninja ZX-9R is a motorcycle in the Ninja sport bike series from Japanese manufacturer Kawasaki, produced from 1994 until 2003. There were five model incarnations across two basic designs.
The BSA Spitfire is a high-performance BSA motorcycle made from 1966 to 1968 with model designations of MkII, MkIII and MkIV. Announced at the Brighton motorcycle show held during September 1965, it was based on the earlier BSA Lightning with a power-upgrade achieved by higher compression-ratio 10.5:1 pistons and two large-bore Amal GP carburettors with velocity stacks it was one of the first BSAs to have 12-volt electrics. At introduction in 1966, it was the fastest standard BSA ever produced and the fastest standard motorcycle tested by Motor Cycle with a best run at 123 mph and average of 119.2 mph The Spitfire was used for travelling Marshalls' course duties at the 1967 Isle of Man TT races.
The Norton P11 is a 745 cc (45.5 cu in) air-cooled OHV parallel twin motorcycle that was made by Norton-Villiers from 1967 to 1969. Designed as an extremely light high power-to-weight ratio desert racer, P11 was revised in 1968 to the P11A and marketed as the Norton Ranger, a road legal version of the P11 with a more comfortable seat to make it suitable for normal road use. The Norton P11 gained a reputation as a 'desert racer' in the late 1960s but by 1969 lighter two stroke desert racers began to dominate the sport and the Norton had begun Commando production and it was selling well. Norton ended production of the P11 series to concentrate on the Commando, which used a number of ideas developed on the P11 series.
The BSA Thunderbolt was a British motorcycle made by BSA at their factory in Armoury Road in Small Heath, Birmingham between 1962 and 1972. Fitted with a single carburettor it was capable of over 100 mph (160 km/h).
The SU carburettor was a constant-depression carburettor made by a British manufacturer of that name or its licensees in various designs spanning most of the twentieth century.
The Lorraine 9N Algol was a French 9-cylinder radial aeroengine built and used in the 1930s. It was rated at up to 370 kW (500 hp), but more usually in the 220–300 kW (300–400 hp) range.
Of the three types of carburetors used on large, high-performance aircraft engines manufactured in the United States during World War II, the Bendix-Stromberg pressure carburetor was the one most commonly found. The other two carburetor types were manufactured by Chandler Groves and Chandler Evans Control Systems (CECO). Both of these types of carburetors had a relatively large number of internal parts, and in the case of the Holley Carburetor, there were complications in its "variable venturi" design.
The BSA A10 series was a range of 646 cc (39.4 cu in) air-cooled parallel twin motorcycles designed by Bert Hopwood and produced by Birmingham Small Arms Company at Small Heath, Birmingham from 1950 to 1963. The series was succeeded by the A65 unit construction models.
The BSA B40 was a series of 350 cc (21 cu in) unit construction single-cylinder OHV four-stroke motorcycles made by the Birmingham Small Arms Company. Developed from the BSA C15, the machines were produced between 1961 and 1967 for civilian use. Military versions were manufactured from 1967 to 1970. Around 14,000 machines were built in total.
The Norton Model 99 Dominator was a 600 cc vertical twin motorcycle manufactured by the British Norton Motorcycle Company at their Bracebridge St, Birmingham factory from 1956 to 1962. The 99 was based on the 500 cc Model 88 Dominator with an enlarged engine. The model was superseded by the 650SS.
The Norton 650 Dominator was a 650 cc vertical twin motorcycle manufactured by the British Norton Motorcycle Company from 1962 to 1967. Initially production was at Norton's Bracebridge St, Birmingham factory, but following the factory's closure in 1963, production was transferred to parent company AMC's works in Plumstead, London. Initially produced in single and twin carburettor versions, the single carb version was soon discontinued. The twin carb version, the 650SS, was described as the 'Best of the Dominators'.
The Ducati 250 Scrambler, known in Europe as the Ducati 250 SCR is an on/off road 249 cc (15.2 cu in) single cylinder bevel drive SOHC motorcycle produced by the Italian manufacturer Ducati from 1962 to 1974. Originally produced for the American Market at the request of the US importers, Berliner Motor Corporation, the model was offered in Europe from 1968. Total production was around 12,000 machines.
The Ducati 250 24 Horas is a 247 cc (15.1 cu in) single cylinder bevel drive SOHC motorcycle produced by the Spanish manufacturer MotoTrans, who were licensed by Ducati to produce motorcycles under the Ducati brand name. The model was based on the 'narrow case' Ducati 250 and produced in three series from 1966 to 1974. It was named after Ducati's successes in the 24 hours of Montjuïc endurance races. Around 2,000 machines were produced in total.
The Ducati Road 250 is a 247 cc (15.1 cu in) single cylinder bevel drive SOHC motorcycle produced by the Spanish manufacturer MotoTrans, who were licensed by Ducati to produce motorcycles under the Ducati brand name and was produced from 1972 to 1977. The model was intended to be a Spanish domestic market version of the 250 Scrambler, although it was also exported to the US in 1972/3.
The Ducati Strada is a 249 cc (15.2 cu in) single cylinder bevel drive SOHC motorcycle produced by the Spanish manufacturer MotoTrans, who were licensed by Ducati to produce motorcycles under the Ducati brand name and was produced from 1978 to 1983. The model is based on the 250 'wide case' Ducati singles which the Italian Ducati factory had stopped manufacturing in 1974, but which MotoTrans continued to develop and produce.
1 2 3 Motor Cycle, 10 November 1966, Earls Court Show Edition p.15 Amal factory advert – the 'new' Concentric and "wide range of controls, handlebars, etc. Amal Limited, Holdford Road, Witton, Birmingham 6." and p.632 Show Guide editorial, "New carburettors are rare...the neat 600 and 900 Concentric carbs are at Earls Court for the first time." Accessed 2013-07-08
1 2 3 Motor Cycle, 7 April 1966, p.1. Amal factory advert – "Carburetters supplied suitable for all types of machines for every purpose. Backed by service throughout the world. All AMAL chromium plated components to BS1224/1965". Accessed 2013-07-10
↑ Motor Cycle, 9 September 1965. p.366 Brighton Show 'Bits and Pieces' "New name in the accessories field is Lozells Engineering, an Amal subsidiary, sharing stand space with the parent company and displaying a range of handlebars and levers." Accessed 2013-08-19
↑ Motor Cycle 23 September 1965 Brighton Show Round-up, p.433 "..twin rotor twist-grip (for twin carburettors, of course)...The Amal Type 313...uses a very solid-looking die-cast body..." Accessed 2013-08-07
↑ Motor Cycle, 24 November 1966, Earls Court Show Review edition p.697 Amal LMC-series clip-ons. Accessed 2013-07-09
↑ Motor Cycle 3 August 1967 p.1071 Amal – Motoplas levers "As distinct from the bulk of the erstwhile Amal control-lever range (now made by Doherty) manufacture of Amal solid light-alloy sports levers has been taken over by the BSA group. These will now be sold under the Motoplas name". Accessed 2013-08-09
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
