Angle deception jamming

Last updated December 30, 2022

Angle deception jamming is an electronic warfare technique used against conical scanning radar systems. It generates a false signal that fools the radar into believing the target is to one side of the boresight, causing the radar to "walk away" from the target and break its radar lock-on. It is also known as angle walk-off, angle stealing, or inverse con-scan.

Angle stealing was one of the earliest jamming techniques to be used operationally, with systems employed against the German Würzburg radars near the end of World War II. The technique is not useful against monopulse radars, and is one of the main reasons those radars became popular in the post-war era.

Angle stealing belongs to the wider class of "deceptive jamming" techniques, which attempt to deceive radars based on knowledge of their operating procedures, rather than simply trying to blind them with noise. Another popular deception technique that was used against early radars is range gate pull-off.

Description

Conical scanning

A typical radar produces a beam that is several degrees wide. The pattern is non-linear; the antenna is most sensitive at the center of the beam, also known as the boresight or centroid, and its sensitivity drops off at greater angles. This pattern is typically represented by measuring the angle where it has one-half the sensitivity as it does on the boresight. This is known as the half power point.

This means that a target in a radar beam will return a signal when the antenna is anywhere within a few degrees of the boresight. The pattern is too wide to allow the radar to directly guide weapons, especially anti-aircraft artillery which need accuracy on the order of 0.1 degrees. However, it is possible to use the non-linear pattern to improve the angle measurement using a system known as conical scanning.

The basic idea of conical scanning is to offset the antenna slightly to one side of the boresight and in front of a parabolic reflector. This causes the beam to be deflected slightly to the opposite side of the boresight. The antenna is then spun so that it rotates (or nutates) around the boresight axis (pointing in the direction of the target). As it rotates, the beam traces out a cone, with its tip at the antenna and its long axis aligned with the boresight. A target that is centred in the boresight will always return some signal to the radar, creating a strong, constant signal. If it is located to one side, the signal will rise and fall as the most sensitive region of the pattern rotates across it.

To use this for automatic tracking, or radar lock-on, a simple circuit is added. First, the signal is sent into a smoother that extracts the amplitude modulated signal of the series of radar pulses that were returned as it swept across the target. This will produce a flat line if the target is centred, or some form of sine wave otherwise. This is then mixed with a second control signal that has a fixed relationship to the spinning of the antenna. For instance, in the case of the Würzburg the antenna spun at 25 Hz, so this fixed signal was also 25 Hz. Sending these two signals into a phase detector produces a varying output that can be used to drive the antenna pointing motors. This output is known as the error signal, and drops to zero when the antenna is pointing directly at the target.

Angle stealing

An angle stealer is a transponder tuned to the radar's operational frequency that also has some knowledge about the timing of the target radar's scanning rate. The rate can be determined by examining the signal as it is received, or by being pre-set based on some basic knowledge of the radar system.

The idea is to add additional signal from the transponder to the signal naturally reflected off the target, such that the addition of those two signals no longer produces the proper output from the smoother. The radar's electronics interpret this as the antenna being misaligned, and it begins to move away from the target. Over time, this can cause the radar to "walk off" the target entirely.

There are two primary methods for causing this to occur:

Inverse gain modulation

Transponders are relatively simple radios that receive a signal, amplify it, and send it back out. Examples were in use for identification friend or foe from the start of World War II. However, these early models had the problem that they often over-amplified the signal, causing interference with other radars. This was addressed in the IFF Mark II with the addition of an automatic gain control system, which amplified the received signal to a pre-set level.

Inverse gain modulation, also known as inverse amplitude modulation, is a simple modification to this sort of transponder. It adds a smoother circuit like the one in the radar receiver, which creates an amplitude modulated signal output. This output is then inverted and sent into the gain control. The result is an output signal that is strong when the radar signal is weak, and weak when it is strong.

Depending on the exact strength of the signals, when this mixes with the radar's own signal at the radar receiver, the result is either a nearly flat smoothed curve, or one that is the inverse of the radar's curve. The resulting error signal quickly drives the radar away from the target. A carefully matched signal that is an exact invert of the original will cause the radar to believe it is aimed at the target no matter where it is pointed.

Swept square wave

The inverse gain technique was so effective against early tracking radars that these radars began using a system known as CORSO, conical-on-receive-signal-only. CORSO typically used two antennas, a transmitter with a fixed antenna, and a conically scanning receiver. The lock-on technique works the same as in a normal conical scan radar, but the transmitted signal is constant and denies the transponder information about the scanning rate of the radar. For this reason, this concept is also known as "silent lobing".

This led to the introduction of the swept square wave (SSW) technique, also known as scan rate modulation. This is generally similar to the inverse gain method, but does not know the scanning rate. Instead, the system sends out pulses on the radar's frequency at a pulse repetition frequency that is similar to the estimated scanning rate of the radar. These pulses will only be received by the radar if the receiver is pointed roughly in the aircraft's direction. To ensure this will occur at some point, the repetition frequency is slowly increased and decreased so that at some point in this pattern it briefly synchronizes with the scan rate of the antenna.

When that occurs, the radar now receives its own signal as well as a second one that is slightly offset in time. When fed into the phase detector, the output signal will no longer be a single pulse, but two, creating an error signal. Because the signal is being swept in repetition frequency, this second part of the signal moves in relation to the radar's own signal. When the two are closely synchronized it generates large error signals that can quickly drive the antenna away from the target. However, because the rate is constantly changing, after a period the error will drop to zero again, potentially before the radar has moved completely off the target.

The system is not as effective as inverse gain, which interrupts the tracking process once every scan compared to the once-every-so-often for SSW, but it provides some protection against any conical scanning or CORSO radar.

Related Research Articles

<span class="mw-page-title-main">Analog television</span> Television that uses analog signals

Analog television is the original television technology that uses analog signals to transmit video and audio. In an analog television broadcast, the brightness, colors and sound are represented by amplitude, phase and frequency of an analog signal.

Radar is a detection system that uses radio waves to determine the distance (ranging), angle, and radial velocity of objects relative to the site. It can be used to detect aircraft, ships, spacecraft, guided missiles, motor vehicles, weather formations, and terrain. A radar system consists of a transmitter producing electromagnetic waves in the radio or microwaves domain, a transmitting antenna, a receiving antenna and a receiver and processor to determine properties of the objects. Radio waves from the transmitter reflect off the objects and return to the receiver, giving information about the objects' locations and speeds.

Radio navigation or radionavigation is the application of radio frequencies to determine a position of an object on the Earth, either the vessel or an obstruction. Like radiolocation, it is a type of radiodetermination.

A continuous wave or continuous waveform (CW) is an electromagnetic wave of constant amplitude and frequency, typically a sine wave, that for mathematical analysis is considered to be of infinite duration. It may refer to e.g. a laser or particle accelerator having a continuous output, as opposed to a pulsed output.

This is an index of articles relating to electronics and electricity or natural electricity and things that run on electricity and things that use or conduct electricity.

<span class="mw-page-title-main">Direction finding</span> Measurement of the direction from which a received signal was transmitted

Direction finding (DF), or radio direction finding (RDF), is – in accordance with International Telecommunication Union (ITU) – defined as radio location that uses the reception of radio waves to determine the direction in which a radio station or an object is located. This can refer to radio or other forms of wireless communication, including radar signals detection and monitoring (ELINT/ESM). By combining the direction information from two or more suitably spaced receivers, the source of a transmission may be located via triangulation. Radio direction finding is used in the navigation of ships and aircraft, to locate emergency transmitters for search and rescue, for tracking wildlife, and to locate illegal or interfering transmitters. RDF was important in combating German threats during both the World War II Battle of Britain and the long running Battle of the Atlantic. In the former, the Air Ministry also used RDF to locate its own fighter groups and vector them to detected German raids.

<span class="mw-page-title-main">Imaging radar</span>

Imaging radar is an application of radar which is used to create two-dimensional images, typically of landscapes. Imaging radar provides its light to illuminate an area on the ground and take a picture at radio wavelengths. It uses an antenna and digital computer storage to record its images. In a radar image, one can see only the energy that was reflected back towards the radar antenna. The radar moves along a flight path and the area illuminated by the radar, or footprint, is moved along the surface in a swath, building the image as it does so.

Beamforming or spatial filtering is a signal processing technique used in sensor arrays for directional signal transmission or reception. This is achieved by combining elements in an antenna array in such a way that signals at particular angles experience constructive interference while others experience destructive interference. Beamforming can be used at both the transmitting and receiving ends in order to achieve spatial selectivity. The improvement compared with omnidirectional reception/transmission is known as the directivity of the array.

<span class="mw-page-title-main">Pulse-Doppler radar</span> Type of radar system

A pulse-Doppler radar is a radar system that determines the range to a target using pulse-timing techniques, and uses the Doppler effect of the returned signal to determine the target object's velocity. It combines the features of pulse radars and continuous-wave radars, which were formerly separate due to the complexity of the electronics.

Continuous-wave radar is a type of radar system where a known stable frequency continuous wave radio energy is transmitted and then received from any reflecting objects. Individual objects can be detected using the Doppler effect, which causes the received signal to have a different frequency from the transmitted signal, allowing it to be detected by filtering out the transmitted frequency.

A low-probability-of-intercept radar (LPIR) is a radar employing measures to avoid detection by passive radar detection equipment while it is searching for a target or engaged in target tracking. This characteristic is desirable in a radar because it allows finding and tracking an opponent without alerting them to the radar's presence. This also protects the radar installation from anti-radiation missiles (ARMs).

Secondary surveillance radar (SSR) is a radar system used in air traffic control (ATC), that unlike primary radar systems that measure the bearing and distance of targets using the detected reflections of radio signals, relies on targets equipped with a radar transponder, that reply to each interrogation signal by transmitting encoded data such as an identity code, the aircraft's altitude and further information depending on its chosen mode. SSR is based on the military identification friend or foe (IFF) technology originally developed during World War II, therefore the two systems are still compatible. Monopulse secondary surveillance radar (MSSR), Mode S, TCAS and ADS-B are similar modern methods of secondary surveillance.

The air traffic control radar beacon system (ATCRBS) is a system used in air traffic control (ATC) to enhance surveillance radar monitoring and separation of air traffic. It consists of a rotating ground antenna and transponders in aircraft. The ground antenna sweeps a narrow vertical beam of microwaves around the airspace. When the beam strikes an aircraft, the transponder transmits a return signal back giving information such as altitude and the Squawk Code, a four digit code assigned to each aircraft that enters a region. Information about this aircraft is then entered into the system and subsequently added to the controller's screen to display this information when queried. This information can include flight number designation and altitude of the aircraft. ATCRBS assists air traffic control (ATC) surveillance radars by acquiring information about the aircraft being monitored, and providing this information to the radar controllers. The controllers can use the information to identify radar returns from aircraft and to distinguish those returns from ground clutter.

Conical scanning is a system used in early radar units to improve their accuracy, as well as making it easier to steer the antenna properly to point at a target. Conical scanning is similar in concept to the earlier lobe switching concept used on some of the earliest radars, and many examples of lobe switching sets were modified in the field to conical scanning during World War II, notably the German Würzburg radar. Antenna guidance can be made entirely automatic, as in the American SCR-584. Potential failure modes and susceptibility to deception jamming led to the replacement of conical scan systems with monopulse radar sets. They are still used by the Deep Space Network for maintaining communications links to space probes. The spin-stabilized Pioneer 10 and Pioneer 11 probes used onboard conical scanning maneuvers to track Earth in its orbit.

Monopulse radar is a radar system that uses additional encoding of the radio signal to provide accurate directional information. The name refers to its ability to extract range and direction from a single signal pulse.

A radar system uses a radio-frequency electromagnetic signal reflected from a target to determine information about that target. In any radar system, the signal transmitted and received will exhibit many of the characteristics described below.

<span class="mw-page-title-main">RCA AN/FPS-16 Instrumentation Radar</span> Ground radar

The AN/FPS-16 is a highly accurate ground-based monopulse single object tracking radar (SOTR), used extensively by the NASA manned space program, the U.S. Air Force and the U.S. Army. The accuracy of Radar Set AN/FPS-16 is such that the position data obtained from point-source targets has azimuth and elevation angular errors of less than 0.1 milliradian and range errors of less than 5 yards (5 m) with a signal-to-noise ratio of 20 decibels or greater.

Radar engineering details are technical details pertaining to the components of a radar and their ability to detect the return energy from moving scatterers — determining an object's position or obstruction in the environment. This includes field of view in terms of solid angle and maximum unambiguous range and velocity, as well as angular, range and velocity resolution. Radar sensors are classified by application, architecture, radar mode, platform, and propagation window.

<span class="mw-page-title-main">Wave radar</span> Technology for measuring surface waves on water

Wave radar is a type of radar for measuring wind waves. Several instruments based on a variety of different concepts and techniques are available, and these are all often called. This article, gives a brief description of the most common ground-based radar remote sensing techniques.

The AR-320 is a 3D early warning radar developed by the UK's Plessey in partnership with US-based ITT-Gilfillan. The system combined the receiver electronics, computer systems and displays of the earlier Plessey AR-3D with a Gilfillan-developed transmitter and planar array antenna from their S320 series. The main advantage over the AR-3D was the ability to shift frequencies to provide a level of frequency agility and thus improve its resistance to jamming.

References

Jones, Jeffrey Frank (2013). Electronic Warfare and Radar Systems Engineering Handbook. Naval Air Warfare Center.

This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.