In dairy farming a bulk milk cooling tank is a large storage tank for cooling and holding milk at a cold temperature until it can be picked up by a milk hauler. The bulk milk cooling tank is an important piece of dairy farm equipment. It is usually made of stainless steel and used every day to store the raw milk on the farm in good condition. It must be cleaned after each milk collection. The milk cooling tank can be the property of the farmer or be rented from a dairy plant.
Raw milk producers have a choice of either open (from 150 to 3000 litres) or closed (from 1000 to 10000 litres) tanks. The cost can vary considerably, depending on manufacturing norms and whether a new or second hand tank is purchased.
Milk silos (10,000 litres and plus) are suitable for the very large producer. These are designed to be installed outside and adjacent to the dairy, all controls and the milk outlet pipe being situated in the dairy.
Tank Construction
Bulk milk cooling tank description
A milk cooling tank, also known as a bulk tank or milk cooler, consists of an inner and an outer tank, both made of high quality stainless steel.
The space between the outer tank and the inner tank is isolated with polyurethane foam. In case of a power failure with an outside temperature of 30°C, the content of the tank will warm up only 1°C in 24 hours.
To facilitate an adequate and rapid cooling of the entire content of a tank, every tank is equipped with at least one agitator. Stirring the milk ensures that all milk inside the tank is of the same temperature and that the milk stays homogeneous.
On top of every closed milk cooling tank is a manhole of about 40 centimetres diameter. This enables thorough cleaning and inspection of the inner tank if necessary. The manhole is covered by a lid and sealed watertight with a rubber ring. Also on top are 2 or 3 small inlets. One is covered with an air-vent, the other(s) can be used to pump milk into the tank.
A milk cooling tank usually stands on 4, 6, or 8 adjustable legs. The built-in tilt of the inner tank ensures that even the last drop of milk will eventually flow to the outlet.
At the bottom, every milk cooling tank has a threaded outlet, usually including a valve.
All tanks have a thermometer, allowing for immediate inspection of the inner temperature.
Most tanks include an automatic cleaning system. Using hot and cold water, an acid and/or alkaline cleaning fluid, a pump and a spray lance will clean the inner tank, ensuring an hygienic inner environment each time the tank is emptied.
Almost every tank has a control box. It manages the cooling process by use of a thermostat. The user can turn the system on and off, allow for extra and immediate stirring, start the cleaning routine, and reset the entire system in case of a failure.
New and bigger milk cooling tanks are now being equipped with monitoring and alarm systems. These systems guard temperature of the milk inside the tank, check the functioning of the agitator, the cooling unit and temperature of the cleaning water. In case of malfunctioning of any of these functions, the alarm will activate. The monitoring system will also keep a record of the temperature and of all malfunctions for a given period.
Bulk tank manufacturing norms
Norms define among other criteria: insulation, milk agitation, cooling power required, variations in milk quantity measurement, calibration, … Some are more demanding than others.
ISO standard 5708 (Refrigerated bulk milk tanks), published in 1983
European standard EN 13732 (Food processing machinery – Bulk milk coolers on farms – Requirements for construction, performance, suitability for use, safety and hygiene), published in 2003, updated in 2009
Northern American sanitary standard 3A 13-11 (3-A Sanitary Standards for Farm Milk Cooling and Holding Tanks, 13-11), effective July 23, 2012 www.3-a.org
Bulk tank outlet standards
Swedish outlet (SMS 1145), German outlet (DIN 11851), English RJT (BS 4825), IDF (ISO 2853), tri-clamp (ISO 2852), Danish outlet (DS 722), .... can be found, not to mention different diameters. They vary from country to country. Non standard outlets make the milk collection process difficult, as the operator needs to adapt to each different standard/diameter.
Cooling Systems
There are two primary methods of cooling milk entering the bulk tank, each with its own advantages and disadvantages. The tank capacity and type will depend on herd size, calving pattern, frequency of milk collection, required milk quality, energy and water availability and future plans for development.
Direct Expansion
A bulk tank with direct expansion cooling has pipes or pillow plates carrying refrigerant which are welded directly to the exterior of the milk chamber. A layer of insulation covers the exterior of the milk tank and the cooling lines, with an exterior metal shell over the insulation.
Direct expansion cooling cannot run when the tank is empty or the inside walls of the tank would freeze. Instead, the tank is rapidly cooled as warm milk first enters the tank, and then the tank is cooled slowly just to maintain a low storage temperature. The rapid cooling during milking requires very large refrigeration compressors and condenser radiators to quickly expel heat from the milk, and is better suited for very large farming operations where three-phase electric power is available to operate the high-power cooling system.
Ice Bank
A bulk tank using an Ice Builder or Ice Bank immerses the bottom of the inner milk chamber in an open pool of water with copper tubes containing refrigerant suspended in the water. Between milkings, a small low-power cooling system slowly builds up a coating of ice around the copper tubes, and prevents icing of the pool over by continuously circulating the water in the pool. After the ice has achieved a thickness of 2-3 inches, the cooling system stops running.
During milking, the milk entering the tank is primarily cooled by circulating the water in the pool around the walls of the inner milk chamber, and the melting of the ice. After the ice has melted sufficiently the cooling system restarts to assist the ice bank and restart the ice building.
Ice bank bulk tanks are better suited for small family farm operations where only single-phase electric power is available, and high-power cooling systems would be either too expensive or difficult to install.
Milk pre-cooling
For energy savings and quality reasons it is advisable to pre-cool the milk before it enters the tank using a plate or a tube cooler (shell and tube heat exchanger) supplied with chilled water from the well water, the ice builder or the condensing unit. The quicker milk is cooled after leaving the cow the better. This system achieves most of the cooling before the milk enters the tank, so that chilled milk, rather than warm milk, is being added to the already cooled milk in the tank.
Cooling temperature
Generic temperature for milk storage is 3 to 4°C. For raw milk cheese manufacturing, it would be advisable to keep the milk at 12°C, as milk characteristics will be kept in a better state.
The milk cooling tank is usually not completely filled at once. A 2 milking tank is designed to cool 50% of its capacity at once. A 4 milking tank is designed to cool 25% of its capacity at once, and a 6 milking tank is designed to cool 16.7% of its capacity at once.
The cooling performance depends on the number of milking it takes to completely fill the tank, the ambient temperature and the cooling time.
Bulk tank cleaning systems
There are two primary methods of cleaning bulk tanks, via manual scrubbing or automatic washing. Both methods generally use four steps to clean the tank:
prerinsing with water to wet the surface and rinse off remaining milk residue
washing with hot soapy water
rinsing with water to remove the soap
final sanitizing rinse with an approved bulk tank sanitizer solution
Manual Scrubbing
Manual scrubbing requires the bulk tank to have large hinged covers that can be lifted open to permit easy access to the interior surfaces of the tank. It tends to be much more thorough than automatic methods since it permits the tank to be carefully inspected during the washing process. If the tank is not found to be cleaned well enough, a troublesome area can be given additional cleansing attention.
Manual Scrubbing Limitations
This job is difficult to perform for very large tanks, and becomes more difficult as the overall cross-section or diameter of the tank increases, requiring either a longer brush or a raised work platform around the tank to lift the cleaning worker to reach over the side of a tall tank.
Automatic Washing
Automatic bulk tank washing and are normally activated by the milk collection truck driver after each milk collection. The cleaning system operates similar to a consumer dishwasher and consists of one or more free-spinning high-pressure spray nozzles with tangential jets, with the spray nozzle mounted on the end of a flexible whip suspended down into the center of the interior. As the cleaning solution sprays out of the jet, the force of the expelled water causes the jet to spin around and the whip to wildly swing back and forth, spraying the cleaning solution randomly all over the interior of the tank.
Automatic Washing Limitations
Because no physical scrubbing occurs with automatic wash systems, the cleanser relies on surfactants and detergents to dissolve the fats left on the interior of the tank by the cream in the milk. However, this is not sufficient to remove milkstone buildup, and the tank may need to be washed occasionally with milkstone remover to remove this scale buildup that can harbor bacteria and contaminants.
Automatic scrubbing only cleans the interior of the tank. It is not capable of cleaning the exterior of the tank, and it does not do a good job of washing around the cover seals. While it is possible to just clean the interior and call it good enough, it does not provide the maximum sanitation of manually washing down the exterior of the tank following or during the automatic wash process. Also, some components that contact the milk such as the drain valve cannot be properly cleaned automatically without disassembling the valve and retaining washer and directly scrubbing in soapy water.
Operating costs
Substantial reductions in running costs can be made when an ice builder is used in conjunction with off-peak electricity. Pre-cooling milk using a plate or a tube cooler supplied with mains or well water can also reduce costs and add to the cooling capacity of the tank.
Bulk tank condenser units, which are not an integral part of the tank, should be fitted in an adjacent, suitable and well ventilated place.
If at all possible, condenser units should not be fitted on a wall facing the sun. They should be installed in a way which allows them to draw in and discharge adequate quantities of air for efficient operation.
Bulk tank should be easily accessible by large bulk collection tankers and positioned so that the tanker approaches can be kept clean and free from cow traffic at all times.
Although tanks have been calibrated when first installed, bulk tank miscalibration is not uncommon and in some cases it can result in significant loss of income. Milk tanks calibrated on the low side, can cheat raw milk producers by up to 22 litres on each shipment. It is therefore advisable to re-calibrate a bulk tank.
Other usage of bulk tanks
Stainless steel bulk tanks are also used to heat or cool a fluid or simply to keep it isolated and warm/cold. Because of the hygienical finishing of the inner and outer side of the tanks, almost any fluid can be stored: water, fruit juices, honey, wine, beer, ink, paint, cosmetics, aromatic food-additives, bacterial cultures, cleansers, oil, or blood.
A dairy is a place where milk is stored and where butter, cheese and other dairy products are made, or a place where those products are sold. It may be a room, a building or a larger establishment. In the United States, the word may also describe a dairy farm or the part of a mixed farm dedicated to milk for human consumption, whether from cows, buffaloes, goats, sheep, horses or camels.
A dishwasher is a machine that is used to clean dishware, cookware, and cutlery automatically. Unlike manual dishwashing, which relies on physical scrubbing to remove soiling, the mechanical dishwasher cleans by spraying hot water, typically between 45 and 75 °C, at the dishes, with lower temperatures of water used for delicate items.
A heat exchanger is a system used to transfer heat between a source and a working fluid. Heat exchangers are used in both cooling and heating processes. The fluids may be separated by a solid wall to prevent mixing or they may be in direct contact. They are widely used in space heating, refrigeration, air conditioning, power stations, chemical plants, petrochemical plants, petroleum refineries, natural-gas processing, and sewage treatment. The classic example of a heat exchanger is found in an internal combustion engine in which a circulating fluid known as engine coolant flows through radiator coils and air flows past the coils, which cools the coolant and heats the incoming air. Another example is the heat sink, which is a passive heat exchanger that transfers the heat generated by an electronic or a mechanical device to a fluid medium, often air or a liquid coolant.
A washing machine is a home appliance used to wash laundry. The term is mostly applied to machines that use water as opposed to dry cleaning or ultrasonic cleaners. The user adds laundry detergent, which is sold in liquid, powder, or dehydrated sheet form, to the wash water.
Dairy farming is a class of agriculture for the long-term production of milk, which is processed for the eventual sale of a dairy product. Dairy farming has a history that goes back to the early Neolithic era, around the seventh millennium BC, in many regions of Europe and Africa. Before the 20th century, milking was done by hand on small farms. Beginning in the early 20th century, milking was done in large scale dairy farms with innovations including rotary parlors, the milking pipeline, and automatic milking systems that were commercially developed in the early 1990s.
An evaporative cooler is a device that cools air through the evaporation of water. Evaporative cooling differs from other air conditioning systems, which use vapor-compression or absorption refrigeration cycles. Evaporative cooling exploits the fact that water will absorb a relatively large amount of heat in order to evaporate. The temperature of dry air can be dropped significantly through the phase transition of liquid water to water vapor (evaporation). This can cool air using much less energy than refrigeration. In extremely dry climates, evaporative cooling of air has the added benefit of conditioning the air with more moisture for the comfort of building occupants.
Dishwashing, washing the dishes, doing the dishes, or washing up in Great Britain, is the process of cleaning cooking utensils, dishes, cutlery and other items to prevent foodborne illness. This is either achieved by hand in a sink using dishwashing detergent or by using a dishwasher and may take place in a kitchen, utility room, scullery or elsewhere.
A chiller is a machine that removes heat from a liquid coolant via a vapor-compression, adsorption refrigeration, or absorption refrigeration cycles. This liquid can then be circulated through a heat exchanger to cool equipment, or another process stream. As a necessary by-product, refrigeration creates waste heat that must be exhausted to ambience, or for greater efficiency, recovered for heating purposes. Vapor compression chillers may use any of a number of different types of compressors. Most common today are the hermetic scroll, semi-hermetic screw, or centrifugal compressors. The condensing side of the chiller can be either air or water cooled. Even when liquid cooled, the chiller is often cooled by an induced or forced draft cooling tower. Absorption and adsorption chillers require a heat source to function.
A refrigerator, colloquially fridge, is a commercial and home appliance consisting of a thermally insulated compartment and a heat pump that transfers heat from its inside to its external environment so that its inside is cooled to a temperature below the room temperature. Refrigeration is an essential food storage technique around the world. The lower temperature lowers the reproduction rate of bacteria, so the refrigerator reduces the rate of spoilage. A refrigerator maintains a temperature a few degrees above the freezing point of water. The optimal temperature range for perishable food storage is 3 to 5 °C. A similar device that maintains a temperature below the freezing point of water is called a freezer. The refrigerator replaced the icebox, which had been a common household appliance for almost a century and a half. The United States Food and Drug Administration recommends that the refrigerator be kept at or below 4 °C (40 °F) and that the freezer be regulated at −18 °C (0 °F).
A somatic cell count (SCC) is a cell count of somatic cells in a fluid specimen, usually milk. In dairying, the SCC is an indicator of the quality of milk—specifically, its low likeliness to contain harmful bacteria, and thus its high food safety. White blood cells (leukocytes) constitute the majority of somatic cells in question. The number of somatic cells increases in response to pathogenic bacteria like Staphylococcus aureus, a cause of mastitis. The SCC is quantified as cells per milliliter. General agreement rests on a reference range of less than 100,000 cells/mL for uninfected cows and greater than 250,000 for cows infected with significant pathogen levels. Several tests like the PortaSCC milk test and The California mastitis test provide a cow-side measure of somatic cell count. The somatic cell count in the milk also increases after calving when colostrum is produced.
Milk cars are a specialized type of railroad car intended to transport raw milk from collection points near dairy farms to a processing creamery. Some milk cars were intended for loading with multiple cans of milk, while others were designed with a single tank for bulk loading. Milk cars were often equipped with high-speed passenger trucks, passenger-type buffer plates, and train signal and steam lines seldom found on conventional refrigerator cars.
An absorption refrigerator is a refrigerator that uses a heat source to provide the energy needed to drive the cooling process. Solar energy, burning a fossil fuel, waste heat from factories, and district heating systems are examples of convenient heat sources that can be used. An absorption refrigerator uses two coolants: the first coolant performs evaporative cooling and then is absorbed into the second coolant; heat is needed to reset the two coolants to their initial states. Absorption refrigerators are commonly used in recreational vehicles (RVs), campers, and caravans because the heat required to power them can be provided by a propane fuel burner, by a low-voltage DC electric heater or by a mains-powered electric heater. Absorption refrigerators can also be used to air-condition buildings using the waste heat from a gas turbine or water heater in the building. Using waste heat from a gas turbine makes the turbine very efficient because it first produces electricity, then hot water, and finally, air-conditioning—trigeneration.
Carpet cleaning is performed to remove stains, dirt, and allergens from carpets. Common methods include hot water extraction, dry-cleaning, and vacuuming.
Storage tanks are containers that hold liquids, compressed gases or mediums used for the short- or long-term storage of heat or cold. The term can be used for reservoirs, and for manufactured containers. The usage of the word tank for reservoirs is uncommon in American English but is moderately common in British English. In other countries, the term tends to refer only to artificial containers.
Water heat recycling is the use of a heat exchanger to recover energy and reuse heat from drain water from various activities such as dish-washing, clothes washing and especially showers. The technology is used to reduce primary energy consumption for water heating.
Pot washing is the process of cleaning low to heavily baked-on items off of restaurant kitchen food equipment, including pots, pans, trays, tubs and more.
A milking pipeline or milk pipeline is a component of a dairy farm animal-milking operation which is used to transfer milk from the animals to a cooling and storage bulk tank.
A parts washer is a piece of equipment used to remove contaminants or debris, such as dirt, grime, carbon, oil, grease, metal chips, cutting fluids, mold release agents, ink, paint, and corrosion from workpieces. Parts washers are used in new manufacturing and remanufacturing processes; they are designed to clean, degrease and dry bulk loads of small or large parts in preparation for assembly, inspection, surface treatment, packaging and distribution. Parts washers may be as simple as the manual "sink-on-a-drum" common to many auto repair shops, or they may be very complex, multi-stage units with pass-through parts handling systems. Parts washers are essential in maintenance, repair and remanufacturing operations as well, from cleaning fasteners, nuts, bolts and screws to diesel engine blocks and related parts, rail bearings, wind turbine gears boxes and automotive assemblies.
The Bender Machine Works in Hayward, Wisconsin, is a dairy equipment manufacturer that played a major role in the history of the dairy farming business in the United States from the 1950s to the 1980s, producing milk pipeline and milk transfer cart components, and washing/vacuum-releasing equipment.
Pumpable icetechnology (PIT) uses thin liquids, with the cooling capacity of ice. Pumpable ice is typically a slurry of ice crystals or particles ranging from 5 micrometers to 1 cm in diameter and transported in brine, seawater, food liquid, or gas bubbles of air, ozone, or carbon dioxide.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
