Dead pedal

Last updated

In an automobile, the dead pedal, often also called a footrest, is typically a non-moving piece of rubber or metal that the driver is supposed to rest their foot on when driving. Although the dead pedal serves no mechanical function in the car, many car manufacturers opt to implement it because it provides a number of ergonomic benefits to the driver. In manual transmission cars, the dead pedal is designed to promote a smoother actuation of the clutch by keeping the driver's foot in the same plane as the pedal. [1] Automatic transmission cars can also benefit from the dead pedal because it prevents fatigue by offering a stable inclined surface on which the driver can place their foot. Even if a car does not have a dead pedal installed, there are a variety of aftermarket accessories that can be installed.

Contents

History

The dead pedal was not a staple component in the original design of automobile pedals. Cars such as the original Ford Model T, 1908, did not have dead pedals and had an upright pedal system. The dead pedal was developed to prevent the accidental actuation of the clutch or brake, also known as left-foot braking, by providing an alternative surface to rest the foot on. The dead pedal became more important with time as stronger and faster cars were developed because the left foot must push against the floor to brace the driver's body. Racing cars and civilian cars with manual transmission systems will have the dead pedal. Cars equipped with an automatic transmission may also have a dead pedal.

Function

The dead pedal serves two main purposes in cars.

The dead pedal provides an inclined surface for the driver's left foot. This allows the driver to brace when maneuvering without accidentally engaging the brakes. This helps the driver maintain more control over the vehicle. [2] It also prevents wear on the brake or clutch pedal because even if no additional pressure is put on these pedals, the constant contact and abrasion of the driver's foot will wear away at the surface of pedals. In automatic cars, the dead pedal is normally just a rubber step placed on the floor of the car. In racing cars, the dead pedal is used to cut down the response time in activating the clutch and is integral to the smooth actuation of the clutch. It is typically an actual pedal located to the left of the clutch. The dead pedal allows for the racer or driver to keep the left foot on the same plane as the clutch, thus making the transition between them smoother and faster. However, the dead pedal still serves no function to the car itself. There have been attempts to advance the dead pedal technology by making it modular [3] and by making it serve a function as an engine regulator. [4]

Type

Footrests

The most common and widely available, these dead pedals come in the form of footrests that are put on the car floor. They come in many forms: some are metal plates, some are rubber pads, and some are simply a raised area of the car floor.

Dummy pedals

These are fake pedals that don't actually serve a function but are still a native part of the car's pedal system. These can be found in some race cars. [1]

Implementation

Dead pedals have never been a required addition to standard automobile pedal sets. This is because the advantages of having a dead pedal are most commonly associated with manual transmission cars. Furthermore, cars with left side drive often have a natural footrest because of the wheel well so it is more common to find the right-side drive cars with dead pedals. However, the dead pedal promotes safe driving habits by serving as a place for drivers to place their foot and prevent accidental left foot braking. It is not recommended to brake with the left foot because it is less confusing when switching between automatic and manual transmission cars. Resting one's foot on the brake pedal may also accidentally light up the brake lights when the vehicle is not decelerating.

The use of the dead pedal is particularly prevalent in right-hand drive markets where the door's bulkhead cannot be used to rest the left foot, for example in the Renault Mégane.

This area may also include other features not associated with direct operation of the vehicle, for instance, a foot button for control of the lights or radio. On certain models of Mercedes-Benz and Volvo vehicles, the parking brake is a pedal located here.

Related Research Articles

<span class="mw-page-title-main">Clutch</span> Mechanical device that connects and disconnects two rotating shafts or other moving parts

A clutch is a mechanical device that allows the output shaft to be disconnected from the rotating input shaft. The clutch's input shaft is typically attached to a motor, while the clutch's output shaft is connected to the mechanism that does the work.

Left-foot braking is the technique of using the left foot to operate the brake pedal in an automobile, leaving the right foot dedicated to the throttle pedal. It contrasts with the practice of using the left foot to operate the clutch pedal, leaving the right foot to share the duties of controlling both brake and gas pedals.

<span class="mw-page-title-main">Cruise control</span> System that automatically controls the speed of a motor vehicle

Cruise control is a system that automatically controls the speed of an automobile. The system is a servomechanism that takes over the car's throttle to maintain a steady speed set by the driver.

<span class="mw-page-title-main">Automatic transmission</span> Type of motor vehicle transmission that automatically changes gear ratio as the vehicle moves

An automatic transmission is a multi-speed transmission used in motor vehicles that does not require any input from the driver to change forward gears under normal driving conditions. Vehicles with internal combustion engines, unlike electric vehicles, require the engine to operate in a narrow range of rates of rotation, requiring a gearbox, operated manually or automatically, to drive the wheels over a wide range of speeds.

<span class="mw-page-title-main">Transmission (mechanical device)</span> Drivetrain transmitting propulsion power

A transmission is a mechanical device which uses a gear set—two or more gears working together—to change the speed or direction of rotation in a machine. Many transmissions have multiple gear ratios, but there are also transmissions that use a single fixed-gear ratio.

<span class="mw-page-title-main">Manual transmission</span> Motor vehicle manual gearbox; stick shift

A manual transmission (MT), also known as manual gearbox, standard transmission, or stick shift, is a multi-speed motor vehicle transmission system, where gear changes require the driver to manually select the gears by operating a gear stick and clutch.

<span class="mw-page-title-main">Freewheel</span> Mechanism which disconnects a driveshaft from a faster-rotating driven shaft

In mechanical or automotive engineering, a freewheel or overrunning clutch is a device in a transmission that disengages the driveshaft from the driven shaft when the driven shaft rotates faster than the driveshaft. An overdrive is sometimes mistakenly called a freewheel, but is otherwise unrelated.

A semi-automatic transmission is a multiple-speed transmission where part of its operation is automated, but the driver's input is still required to launch the vehicle from a standstill and to manually change gears. Semi-automatic transmissions were almost exclusively used in motorcycles and are based on conventional manual transmissions or sequential manual transmissions, but use an automatic clutch system. But some semi-automatic transmissions have also been based on standard hydraulic automatic transmissions with torque converters and planetary gearsets.

<span class="mw-page-title-main">Drive by wire</span> Automotive technology

Drive by wire or DbW technology in the automotive industry is the use of electronic or electro-mechanical systems in place of mechanical linkages that control driving functions. The concept is similar to fly-by-wire in the aviation industry. Drive-by-wire may refer to just the propulsion of the vehicle through electronic throttle control, or it may refer to electronic control over propulsion as well as steering and braking, which separately are known as steer by wire and brake by wire, along with electronic control over other vehicle driving functions.

<span class="mw-page-title-main">Direct-shift gearbox</span> Type of dual-clutch transmission

A direct-shift gearbox is an electronically controlled, dual-clutch, multiple-shaft, automatic gearbox, in either a transaxle or traditional transmission layout, with automated clutch operation, and with fully-automatic or semi-manual gear selection. The first dual-clutch transmissions were derived from Porsche in-house development for the Porsche 962 in the 1980s.

<span class="mw-page-title-main">Preselector gearbox</span> Type of manual transmission

A preselector gearbox is a type of manual transmission mostly used on passenger cars and racing cars in the 1930s, in buses from 1940–1960 and in armoured vehicles from the 1930s to the 1970s. The defining characteristic of a preselector gearbox is that the gear shift lever allowed the driver to "pre-select" the next gear, usually with the transmission remaining in the current gear until the driver pressed the "gear change pedal" at the desired time.

Hill-holder is a motor vehicle device that holds the brake until the clutch is at the friction point, making it easier for a stationary vehicle to start uphill. By holding the brake in position while the vehicle is put into gear, it prevents rollback. It was invented by Wagner Electric and manufactured by Bendix Brake Company in South Bend, Indiana.

<span class="mw-page-title-main">Parking brake</span> Secondary automotive braking system

In road vehicles, the parking brake, also known as a handbrake or emergency brake (e-brake), is a mechanism used to keep the vehicle securely motionless when parked. Parking brakes often consist of a pulling mechanism attached to a cable which is connected to two wheel brakes. In most vehicles, the parking brake operates only on the rear wheels, which have reduced traction while braking. The mechanism may be a hand-operated lever, a straight pull handle located near the steering column, or a foot-operated pedal located with the other pedals.

A transmission control unit (TCU), also known as a transmission control module (TCM), or a gearbox control unit (GCU), is a type of automotive ECU that is used to control electronic automatic transmissions. Similar systems are used in conjunction with various semi-automatic transmissions, purely for clutch automation and actuation. A TCU in a modern automatic transmission generally uses sensors from the vehicle, as well as data provided by the engine control unit (ECU), to calculate how and when to change gears in the vehicle for optimum performance, fuel economy and shift quality.

<span class="mw-page-title-main">Gear stick</span> Lever used for shifting gears manually

A gear stick, gear lever, gearshift or shifter, more formally known as a transmission lever, is a metal lever attached to the transmission of an automobile. The term gear stick mostly refers to the shift lever of a manual transmission, while in an automatic transmission, a similar lever is known as a gear selector. A gear stick will normally be used to change gear whilst depressing the clutch pedal with the left foot to disengage the engine from the drivetrain and wheels. Automatic transmission vehicles, including hydraulic automatic transmissions, automated manual and older semi-automatic transmissions, like VW Autostick, and those with continuously variable transmissions, do not require a physical clutch pedal.

<span class="mw-page-title-main">Non-synchronous transmission</span> Form of manual transmission

A non-synchronous transmission, also called a crash gearbox, is a form of manual transmission based on gears that do not use synchronizing mechanisms. They require the driver to manually synchronize the transmission's input speed and output speed.

<span class="mw-page-title-main">Line lock</span> Vehicle braking technology

A line lock is a device that allows the front brakes to lock independently of the rear brakes via a switch. The device is an electric solenoid that controls a valve which allows the brakes to be controlled individually. This allows the front brakes to be locked and the rear brakes to be open, and allows the driver to spin the rear wheels without wasting the rear brakes. This method is referred to as line lock and is popular among enthusiasts who like to do burnouts.

<span class="mw-page-title-main">Motorcycle transmission</span> Transmission for motorcycle applications

A motorcycle transmission is a transmission created specifically for motorcycle applications. They may also be found in use on other light vehicles such as motor tricycles and quadbikes, go-karts, offroad buggies, auto rickshaws, mowers, and other utility vehicles, microcars, and even some superlight racing cars.

<span class="mw-page-title-main">Adapted automobile</span> Automobile adapted for ease of use by disabled people

An adapted automobile is an automobile adapted for ease of use by people with disabilities. Automobiles, whether cars or vans, can be adapted for a range of physical disabilities.

<span class="mw-page-title-main">Car controls</span> Car parts used to control the vehicle

Car controls are the components in automobiles and other powered road vehicles, such as trucks and buses, used for driving and parking.

References

  1. 1 2 "What is a Dead Pedal? (with picture)". Wiki Motors. 2023-10-05.
  2. ↑ "What every motorist should know". www.driving-school.com.au. Archived from the original on 29 April 2007. Retrieved 13 January 2022.
  3. ↑ U.S. patent 6,318,786
  4. ↑ U.S. patent 6,347,680
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.