Edition (printmaking)

Last updated November 14, 2021

In printmaking, an edition is a number of prints struck from one plate, usually at the same time. This may be a limited edition , with a fixed number of impressions produced on the understanding that no further impressions (copies) will be produced later, or an open edition limited only by the number that can be sold or produced before the plate wears. Most modern artists produce only limited editions, normally signed by the artist in pencil, and numbered as say 67/100 to show the unique number of that impression and the total edition size.

Original or reproduction?

An important and often confused distinction is that between editions of original prints, produced in the same medium as the artist worked (e.g., etching, or lithography), and reproduction prints (or paintings), which are photographic reproductions of the original work, essentially in the same category as a picture in a book or magazine, though better printed and on better paper. These may be marketed as "limited editions" with investment potential (which is rarely realized), and even signed and numbered by the artist. Some knowledge is often required to tell the difference.

Development of the concept

One of the main reasons for the development of printmaking was the desire of artists to make more money from their work by selling multiple copies; printmaking satisfies this motive. The production of multiple copies also tends to reduce production costs and market price when compared to a single or unique image. Until the 19th century, in the period of the Old master print the concept of an edition did not really apply to prints, unlike books. Prints were often run off as demand allowed, and often worn-out plates were reworked by the original artist or another, to produce a new state. The art market attempts to distinguish between "lifetime impressions" and "late impressions", which were produced after the death of the artist. This can be done to some extent by the study of the paper involved, and its watermark, and the condition of the plate as revealed by the printed image. But it remains a difficult area.

The aquatints of Goya, which are done in a technique that wears out quickly on the plate, were the first important prints to be published initially in limited editions, which however were not signed or numbered. In fact the plates survived, and since Goya's death several further editions have been published, showing a progressive and drastic decline in quality of the image, despite some rework. Because of this and other cases, "posthumous editions" produced after the death of an artist, and obviously not signed by him, are usually far less sought after. The plates of later prints are often "cancelled" by defacing the image, with a couple of impressions of the cancelled plate taken to document it. This is now expected by collectors and investors, who want the prints they buy to retain their value.

Modern practice

Prints by artists today may potentially retain their financial value as art (i.e., as an appreciating investment) because they are created by an artistic process rather than by a strictly mechanical one, and may become scarce because the number of multiples is limited. In Rembrandt's time, the limit on the size of an edition was practical: a plate degrades through use, putting an upper limit on the number of images to be struck. Plates can be reworked and restored to some degree, but it is generally not possible to create more than a thousand prints from any process except lithography or woodcut. A few hundred is a more practical upper limit, and even that allows for significant variation in the quality of the image. In drypoint, 10 or 20 may be the maximum number of top-quality impressions possible.

Today, artists will sometimes refer to a print as a "one-off," meaning that the artist has made a unique print and no reproductions of it from the original matrix, often not even a proof. In this category one sometimes finds monotypes, monoprints, collagraphs, altered prints with collage or chine colle additions, or even hand-colored prints. There remain artists who are strong advocates of "artist's prints" which are conceived, printed, signed, and given the edition number 1/1 by the artist.

Numbering

Because of the variation in quality, lower-numbered prints in an edition are sometimes favored as superior, especially with older works where the image was struck until the plate wore out. However the numbering of impressions in fact may well not equate at all to the sequence in which they were printed, and may often be the reverse of it.

In later times, printmakers recognized the value of limiting the size of an edition and including the volume of the edition in the print number (e.g., "15/30" for the 15th print in an edition of 30). Tight controls on the process to limit or eliminate variation in quality have become the norm. In monotyping, a technique where only two impressions at most can be taken, prints may be numbered 1/1, or marked "unique". Artists usually print an edition much smaller than the plate allows, both for marketing reasons and to keep the edition comfortably within the lifespan of the plate. Specific steps may also be taken to strengthen the plate, such as electroplating intaglio images, which uses an electric process to put a very thin coat of a stronger metal onto a plate of a weaker metal.

The conventions for numbering prints are well-established, a limited edition is normally hand signed and numbered by the artist, typically in pencil, in the form (e.g.): 14/100. The first number is the number of the print itself. The second number is the number of overall prints the artist will print of that image. The lower the second number is, the more valuable and collectible the limited editions are likely to be, within whatever their price range is. Other marks may indicate that a print has been made in addition to the numbered prints of an edition. Artist's proofs are marked "A. P." or "P/A", sometimes E. A. or E. d'A. (épreuve d'artiste); monoprints and uniquely hand-altered prints are marked "unique"; prints that are given to someone or are for some reason unsuitable for sale are marked "H. C." or "H/C", meaning "hors de commerce", not for sale. These are usually prints reserved for the publisher, like Artist's Proofs. The printer is also often allowed to retain some proof impressions; these are marked "P. P." Finally, a master image may be printed against which the members of the edition are compared for quality: these are marked as "bon à tirer" or "BAT" ("good to print" in French). In all, the number of the main edition can represent 50% or less of the total number of good impressions taken.^[1]

Professional artist printmakers will sometimes limit an edition to several artist's proof copies, including a "bon a tirer" print and then one unique copy designated as a "one-off" or "1/1" or "one/off".

Consumer protection laws

In the United States limited editions are regulated under state consumer protections laws. California became the first state to regulate the sale of limited edition art prints with the "California Print Law" of 1971.^[2]^[3] The state of Illinois later expanded on the California statute.^[4] However, it was not until 1986 that more comprehensive provisions, still in place today, were enacted with the passage of the "Georgia Print Law". That law became the template for statutes subsequently enacted by other states.^[4]^[5] The Georgia Print Law written by (former) State Representative Chesley V. Morton, became effective July 1, 1986.^[5] The law requires art dealers, artists, or auctioneers to supply information to perspective purchasers about the nature of the print, the number of prints and editions (including HC editions) produced, and the involvement (if any) of the artist in the creation of the print. The penalty for violation of the law ranges from simple reimbursement to treble damages, in the case of a willful violation. Those found to be in violation of the law are also liable for court costs, expenses, and attorney fees. The law applies to works of art valued at more than $100.00 (not including frame). Charitable organizations are specifically exempt from the provision of the law. The statute of limitations is one year after discovery, and, if discovery of the violation is not made within three years of the sale, then the purchaser’s remedies are extinguished.^[4]

Related Research Articles

Printmaking is the process of creating artworks by printing, normally on paper, but also on fabric, wood, metal, and other surfaces. "Traditional printmaking" normally covers only the process of creating prints using a hand processed technique, rather than a photographic reproduction of a visual artwork which would be printed using an electronic machine ; however, there is some cross-over between traditional and digital printmaking, including risograph. Except in the case of monotyping, all printmaking processes have the capacity to produce identical multiples of the same artwork, which is called a print. Each print produced is considered an "original" work of art, and is correctly referred to as an "impression", not a "copy". However, impressions can vary considerably, whether intentionally or not. Master printmakers are technicians who are capable of printing identical "impressions" by hand. Historically, many printed images were created as a preparatory study, such as a drawing. A print that copies another work of art, especially a painting, is known as a "reproductive print".

Mezzotint is a printmaking process of the intaglio family. It was the first tonal method to be used, enabling half-tones to be produced without using line- or dot-based techniques like hatching, cross-hatching or stipple. Mezzotint achieves tonality by roughening a metal plate with thousands of little dots made by a metal tool with small teeth, called a "rocker". In printing, the tiny pits in the plate retain the ink when the face of the plate is wiped clean. This technique can achieve a high level of quality and richness in the print.

Monotyping is a type of printmaking made by drawing or painting on a smooth, non-absorbent surface. The surface, or matrix, was historically a copper etching plate, but in contemporary work it can vary from zinc or glass to acrylic glass. The image is then transferred onto a sheet of paper by pressing the two together, usually using a printing-press. Monotypes can also be created by inking an entire surface and then, using brushes or rags, removing ink to create a subtractive image, e.g. creating lights from a field of opaque colour. The inks used may be oil or water-based. With oil-based inks, the paper may be dry, in which case the image has more contrast, or the paper may be damp, in which case the image has a 10 percent greater range of tones.

Drypoint is a printmaking technique of the intaglio family, in which an image is incised into a plate with a hard-pointed "needle" of sharp metal or diamond point. In principle, the method is practically identical to engraving. The difference is in the use of tools, and that the raised ridge along the furrow is not scraped or filed away as in engraving. Traditionally the plate was copper, but now acetate, zinc, or plexiglas are also commonly used. Like etching, drypoint is easier to master than engraving for an artist trained in drawing because the technique of using the needle is closer to using a pencil than the engraver's burin.

Aquatint is an intaglio printmaking technique, a variant of etching that produces areas of tone rather than lines. For this reason it has mostly been used in conjunction with etching, to give both lines and shaded tone. It has also been used historically to print in colour, both by printing with multiple plates in different colours, and by making monochrome prints that were then hand-coloured with watercolour.

An artist's proof is an impression of a print taken in the printmaking process to see the current printing state of a plate while the plate is being worked on by the artist. A proof may show a clearly incomplete image, often called a working proof or trial impression, but in modern practice is usually used to describe an impression of the finished work that is identical to the numbered copies. There can also be printer's proofs which are taken for the printer to see how the image is printing, or are final impressions the printer is allowed to keep; but normally the term "artist's proof" would cover both cases.

Digital printing is a method of printing from a digital-based image directly to a variety of media. It usually refers to professional printing where small-run jobs from desktop publishing and other digital sources are printed using large-format and/or high-volume laser or inkjet printers.

The bibliographical definition of an edition includes all copies of a book printed “from substantially the same setting of type,” including all minor typographical variants.

The terms special edition, limited edition, and variants such as deluxe edition, or collector's edition, are used as a marketing incentive for various kinds of products, originally published products related to the arts, such as books, prints, recorded music and films, and videogames, but now including clothing, cars, fine wine, and whisky, among other products. A limited edition is restricted in the number of copies produced, although in fact the number may be very low or very high. Suzuki (2008) defines limited edition products as those “sold in a state that makes them difficult to obtain because of companies limiting their availability to a certain period, quantity, region, or channel". A special edition implies there is extra material of some kind included. The term is frequently used on DVD film releases, often when the so-called "special" edition is actually the only version released.

Intaglio is the family of printing and printmaking techniques in which the image is incised into a surface and the incised line or sunken area holds the ink. It is the direct opposite of a relief print where the parts of the matrix that make the image stand above the main surface.

Monoprinting is a type of printmaking where the intent is to make unique prints, that may explore an image serially. Other methods of printmaking create editioned multiples, the monoprint is editioned as 1 of 1. There are many techniques of mono-printing, in particular the monotype. Printmaking techniques which can be used to make mono-prints include lithography, woodcut, and etching.

The etching revival was the re-emergence and invigoration of etching as an original form of printmaking during the period approximately from 1850 to 1930. The main centres were France, Britain and the United States, but other countries, such as the Netherlands, also participated. A strong collector's market developed, with the most sought-after artists achieving very high prices. This came to an abrupt end after the 1929 Wall Street crash wrecked what had become a very strong market among collectors, at a time when the typical style of the movement, still based on 19th-century developments, was becoming outdated.

Master E. S. is an unidentified German engraver, goldsmith, and printmaker of the late Gothic period. He was the first major German artist of old master prints and was greatly copied and imitated. The name assigned to him by art historians, Master E. S., is derived from the monogram, E. S., which appears on eighteen of his prints. The title, Master, is used for unidentified artists who operated independently. He was probably the first printmaker to place his initials on his work.

An old master print is a work of art produced by a printing process within the Western tradition. The term remains current in the art trade, and there is no easy alternative in English to distinguish the works of "fine art" produced in printmaking from the vast range of decorative, utilitarian and popular prints that grew rapidly alongside the artistic print from the 15th century onwards. Fifteenth-century prints are sufficiently rare that they are classed as old master prints even if they are of crude or merely workmanlike artistic quality. A date of about 1830 is usually taken as marking the end of the period whose prints are covered by this term.

In printmaking, a state is a different form of a print, caused by a deliberate and permanent change to a matrix such as a copper plate or woodblock.

A facsimile is a copy or reproduction of an old book, manuscript, map, art print, or other item of historical value that is as true to the original source as possible. It differs from other forms of reproduction by attempting to replicate the source as accurately as possible in scale, color, condition, and other material qualities. For books and manuscripts, this also entails a complete copy of all pages; hence, an incomplete copy is a "partial facsimile". Facsimiles are sometimes used by scholars to research a source that they do not have access to otherwise, and by museums and archives for media preservation and conservation. Many are sold commercially, often accompanied by a volume of commentary. They may be produced in limited editions, typically of 500–2,000 copies, and cost the equivalent of a few thousand United States dollars. The term "fax" is a shortened form of "facsimile" though most faxes are not reproductions of the quality expected in a true facsimile.

Artist's multiple is a series of identical art objects produced or commissioned by artist according to his or her idea, usually a signed limited edition made specifically for selling.

Chesley V. Morton is an American stockbroker, securities arbitrator, and former member of the Georgia House of Representatives.

À la poupée is a largely historic intaglio printmaking technique for making colour prints by applying different ink colours to a single printing plate using ball-shaped wads of cloth, one for each colour. The paper has just one run through the press, but the inking needs to be carefully re-done after each impression is printed. Each impression will usually vary at least slightly, and sometimes very significantly.

In printmaking, surface tone, or surface-tone, is produced by deliberately or accidentally not wiping all the ink off the surface of the printing plate, so that parts of the image have a light tone from the film of ink left. Tone in printmaking meaning areas of continuous colour, as opposed to the linear marks made by an engraved or drawn line. The technique can be used with all the intaglio printmaking techniques, of which the most important are engraving, etching, drypoint, mezzotint and aquatint. It requires individual attention on the press before each impression is printed, and is mostly used by artists who print their own plates, such as Rembrandt, "the first master of this art", who made great use of it.

References

↑ "Art Terms: Printmaking". Art Cellar Exchange.
↑ "California Code, Civil Code - CIV § 1740". FindLaw. Retrieved March 2, 2019.
↑ "Grogan-Beall v. Ferdinand Roten Galleries, Inc. (1982)". JUSTIA USA Law. Retrieved March 2, 2019.
1 2 3 "Introduction" (PDF). ArtsGeorgia. Archived from the original (PDF) on 2013-06-17. Retrieved 2013-05-04.
1 2 Gignilliat, William R. (1986). Handbook on the Georgia print law. Atlanta: GVLA. pp. 1–122. ASIN B00072LAHS.

External links

What is a print? from the International Fine Art Printers Association

This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.

[1] "Art Terms: Printmaking". Art Cellar Exchange.

[2] "California Code, Civil Code - CIV § 1740". FindLaw. Retrieved March 2, 2019.

[3] "Grogan-Beall v. Ferdinand Roten Galleries, Inc. (1982)". JUSTIA USA Law. Retrieved March 2, 2019.

[Print-4] 1 2 3 "Introduction" (PDF). ArtsGeorgia. Archived from the original (PDF) on 2013-06-17. Retrieved 2013-05-04.

[Gignilliat-5] 1 2 Gignilliat, William R. (1986). Handbook on the Georgia print law. Atlanta: GVLA. pp. 1–122. ASIN B00072LAHS.

[1]

[2]

[3]

[4]

[5]