Fiat ESVs (Experimental Safety Vehicle) are a small series of prototypes built by Fiat in the early 1970s, intended for research on passive safety features.
In Spring 1971, Fiat starts a project to research passive safety of small (up to 1,200lb, 540kg) and middle class cars (up to 1,800lb, 820kg). In that year, the Fiat 500 has a 23.3% market share in Italy, and thus is an important factor in the safety on the Italian roads.[1] In the same year, the American organization NHSB - National Highway Safety Bureau (later known as National Highway Traffic Safety Administration, NHTSA) launches a competition reserved for American manufacturers, for the construction of an entirely new vehicle, intended to guarantee maximum passive safety.
At the end of 1971, only two American manufacturers, which do not even produce automobiles, have applied to the NHSB competition. Given the lack of interest, it is decided to extend the offer to all global manufacturers. In 1972, the American manufacturers Ford and General Motors as well as Fiat, Daimler-Benz, Volkswagen, Nissan and Honda join this initiative.
These ESV cars are designed on the basis of the specifications established during the various conferences held around the world: January 1971 in Paris, France; September 1971 in Sindelfingen, Germany; July 1972 in Washington DC; March 1973 in Kyoto, Japan and June 1974, in London, England.[2]
Fiat is the only manufacturer in the NHSB project to present one model each in three different weight categories. They stand out with very visible black protection of the front and rear of the cars, and have the ESV logo and a number indicating the weight of the vehicle in pounds, as prescribed in the American specifications.[1]
The main safety test requirements of this project are protection of the passengers in:
a frontal or rear collision against a barrier at 80km/h (50mph)
a collision against a pole, frontal or at the rear, at 80km/h (50mph)
a lateral collision against a pole at a speed of 24km/h (15mph)
As main differences with the standard cars they are based on, the three Fiat ESVs have in common: a reinforced inner skeleton, big polyurethane bumpers (in two versions: one developed by Pirelli with air chambers, the other filled with foam)[4] at both ends with matching side protection strips, and a padded interior. The weight increase varies between 43% for the largest model and 50% for the smallest model. Also the production cost goes up, between 37% and 43%.[5] Due to the higher weight, the cars all need a larger engine than standard, and the fuel consumption increases. Also the suspension is enforced and the wheels and tires are a size bigger than standard.
In all, Fiat produces 47 ESV vehicles between 1972 and 1974, at a total cost of 4.5 billion Lire (40-50 million euros).[6] None of the experimental models designed by Fiat (or the other companies participating in this automotive safety experiment) makes it to mass production, but many elements can be seen on production models in the years to follow. Examples of the Fiat ESVs are the shock absorbing bumpers, fuel tank behind the rear seat and reinforced passenger cell with side impact protection bars in the doors of the Fiat 131, introduced in 1974 for Europe and in 1975 for the USA.[7]
Most of the Fiat ESVs are scrapped, but three are kept and are on display at the Heritage HUB in Turin, Italy.
Fiat ESV 1500
Fiat ESV 1500
The ESV 1500 project commences before the NHSB invitation to join the program. It is derived from the Fiat 500, with rear engine and rear-wheel drive, and is presented at the 1972 convention in Washington DC. Originally, it weighs no more than the targeted 680kg (1,500lb), with styling done by the engineers, who borrow certain elements from the yet-to-be-released Fiat 126. After the presentation, Fiat updates the experimental model for the 1973 presentation in Kyoto as the first versions would not pass the frontal pole collision test.
The extra reinforcements mean that the eventual prototype weighs 780kg (1,720lb). This means it is above the target of 1,500lb (680kg). Because of its weight, it is fitted with an enlarged engine: 600 cc instead of 500 cc. One of the safety features that Fiat also tests in the ESV 1500, is the use of airbags, among other restraint systems. The conclusion is that at that time, there is no satisfactory restraint system for speeds of 50mph (80km/h) for a car of this size, including airbags.[5] In total, thirteen ESV 1500 prototypes are built.[8][9]
Fiat ESV 2000
Fiat ESV 2000
The ESV 2000 is first presented in 1973, in Kyoto. It has five doors and front wheel drive; it is derived from the 128. The engine displacement is 1300 cc instead of 1100 cc, because the car weighs 360kg (794lb) more than the standard model. For the styling of this car, Fiat Centro Stile is asked to make the proposals. While the original Fiat 128 is not marketed with five doors Fiat decides to add a tailgate for the ESV 2000 to provide an additional emergency exit.
Also, the windshield is deeply curved so it sits further from the front occupants' heads than in the 128, without any change in the position and rake of the original A-pillars. The roof is slightly raised from the B-pillar aft, to allow for an extra strong roll-over bar.[10] Finally, the spare wheel is moved from the engine bay to the trunk and the fuel tank is moved forward from below the trunk to right behind the passenger compartment. In testing, the concessions to the styling of the car that the Centro Stile wanted, turn out to have negative consequences for the crash test results. Twenty examples of the ESV 2000 are built.
Fiat ESV 2500
Fiat ESV 2500
The ESV 2500 is based on the Fiat 124 and has a front engine with rear wheel drive. In terms of weight, it is almost twice the 124, and it would also cost much more, thus making it unviable on the market. Although the shape of the car remains that of a three box sedan, the ESV 2500 gets a tailgate like the ESV 2000. Also here the windshield is curved compared to the original, and the fuel tank is moved to a safer position right behind the passenger compartment.[11]
Notes and references
1 2 Montabone, Oscar (October 26–29, 1971). Report on the Second International Technical Conference on Experimental Safety Vehicles. Sindelfingen, Germany: Department of Transportation, National Highway Traffic Safety Administration. pp.2/157–2/184.
↑ Bernabò, Ferruccio (1973-03-10). "Vetture – sicurezza Conferenza a Kyoto" [Vehicles – safety conference in Kyoto]. La Stampa (in Italian). Vol.107, no.59. p.17.
↑ Kuipers, Hans (1973). Veiligheidsauto's[Safety cars]. Grote Alken (in Dutch). Vol.650. Uitgeverij De Alk bv. p.70. ISBN90-6013-650-0.
1 2 Montanari, Vittorio (March 13–16, 1973). Report on the Fourth International Technical Conference on Experimental Safety Vehicles. Kyoto, Japan: Department of Transportation, National Highway Traffic Safety Administration. pp.2/443–2/475.
The Fiat 128 is a transverse front-engine, front wheel drive small family car manufactured and marketed by Fiat from 1969 to 1985 as a two- or four-door sedan, three- or five-door station wagon as well as two- or three-door coupé. The 128 running gear and engine, reconfigured for a mid-engined layout, were used in the Fiat X1/9 sports car.
The Fiat X1/9 is an Italian two-seater mid-engined sports car designed by Bertone and manufactured by Fiat from 1972–1982 and subsequently by Gruppo Bertone from 1982–1989.
The Fiat 127 is a supermini car produced by Italian car manufacturer Fiat from 1971 to 1983. It was introduced in 1971 as the replacement for the Fiat 850. Production of the 127 in Italy ended in 1983 following the introduction of its replacement, the Fiat Uno, although the nameplate continued to be used on cars imported from Brazil.
The Fiat 124 is a small family car manufactured and marketed by Italian company Fiat between 1966 and 1974. The saloon superseded the Fiat 1300 and spawned station wagon, four-seater coupé, and two-seater convertible variants.
The Fiat 500 is an economy / city car that was manufactured and marketed by Fiat Automobiles from 1957 until 1975. It was sold as a two-door semi-convertible or saloon car and as a three-door panel van or estate car.
The Fiat Ritmo is a small, front-engine, front-wheel drive family car manufactured and marketed by Fiat, launched in April 1978 at the Turin Motor show and offered in 3- and 5-door hatchback and cabriolet body styles – from 1978 to 1988 with two facelifts.
The Fiat 131 is a family car manufactured and marketed by Fiat from 1974 to 1984 after its debut at the 1974 Turin Motor Show. Available as a two-door and four-door saloon and 5-door estate across a single generation, the 131 succeeded the Fiat 124.
The Fiat 600 is a small, rear-engined city car and economy family car made by Italian carmaker Fiat from 1955 to 1969 — offered in two-door fastback sedan and four-door Multipla mini MPV body styles. The 600 is considered a pop icon of the Italian economic miracle, and the three-row seating Multipla, though diminutive and odd-looking, is seen as one the first mass-produced minivans.
The Fiat 1100 is a small family car produced from 1953 until 1969 by the Italian manufacturer Fiat. It was an all-new unibody replacement for the Fiat 1100 E, which descended from the pre-war, body-on-frame Fiat 508 C Balilla 1100. The 1100 was changed steadily and gradually until being replaced by the new Fiat 128 in 1969. There were also a series of light commercial versions of the 1100 built, with later models called the Fiat 1100T, which remained in production until 1971. The Fiat 1100 D also found a long life in India, where Premier Automobiles continued to build the car until the end of 2000.
The Fiat Regata is an automobile produced by Italian automaker Fiat from 1983 until 1990. The Regata name was used for the sedan and station wagon versions of the Fiat Ritmo hatchback, corresponding to the post-facelift Ritmo. The Regata was offered with a choice of three petrol and two diesel engines, although Fiat's Argentinean operations installed other engines from later Fiat models as production there continued until 1995.
The Volvo VESC, the Volvo Experimental Safety Car, was a concept car made by Volvo to showcase a number of innovative passenger safety features. It was unveiled in 1972 at the Geneva Motor Show.
The FSO Polonez is a motor vehicle that was developed in Poland in collaboration with Fiat and produced by Fabryka Samochodów Osobowych from 1978 to 2002. It was based on the Polski Fiat 125p platform with a new hatchback design by Zbigniew Watson, Walter de Silva and Giorgetto Giugiaro. It was available in body styles that included two- and four-door compact-sized cars, station wagons, as well as commercial versions as pickup truck, cargo van, and ambulance. Production totaled more than one million units, excluding the pickup truck and van variants. The Polonez was marketed in other nations and was popular in its domestic market until Poland joined the European Union in 2004.
A side collision is a vehicle crash where the side of one or more vehicles is impacted. These crashes typically occur at intersections, in parking lots, and when two vehicles pass on a multi-lane roadway.
The Fiat 1400 and Fiat 1900 are passenger cars produced by Italian automotive manufacturer Fiat from 1950 to 1958 and from 1952 to 1959 respectively. The two models shared body and platform, but while the 1.4-litre 1400 was Fiat's intermediate offering, the upmarket 1900 had an enlarged 1.9-litre engine and more luxurious trim and equipment, to serve as flagship in the manufacturer's range.
The Fiat 518, also called Fiat Ardita, was a model of car produced by Italian car manufacturer Fiat between 1933 and 1938. The name "Ardita" was also used on the six-cylinder engined and more expensive Fiat Ardita 2500 or 527.
The Fiat 1800 and 2100 are six-cylinder automobiles produced by Italian manufacturer Fiat between 1959 and 1968. Both models were introduced in 1959. A four-cylinder 1500-cc version, the 1500L, was added to the range in 1963, when the 2100 was replaced by the larger engined 2300. The 1800/2100 were designed by Fiat's own Dante Giacosa.
The Fiat 1500 was a six-cylinder car produced by the Fiat from 1935 to 1950. It was one of the first cars tested in a wind tunnel, following the Chrysler Airflow produced one year earlier. The streamlined styling achieved an aerodynamic efficiency unequalled before it in a touring car and disproved the thesis aerodynamic cars would not sell.
Sipani Automobiles Ltd. was an Indian car manufacturer established in 1973, located in Bangalore. They mainly manufactured subcompact cars with fibreglass bodies. They also took over Auto Tractors Limited in 1991 and manufactured diesel engines and tractors in the old ATL factory in Pratapgarh, Uttar Pradesh.
The Fiat 1100 is a small family car produced from 1937 to 1953 by the Italian car manufacturer Fiat. It was introduced in 1937 as Fiat 508 C or Balilla 1100, as a replacement for the Fiat 508 Balilla. Under the new body the 508 C had more modern and refined mechanicals compared to the 508, including independent front suspension and an enlarged overhead valve engine. In 1939 it was updated and renamed simply Fiat 1100. The 1100 was produced in three consecutive series—1100, 1100 B and 1100 E—until 1953, when it was replaced by the all-new, unibody Fiat 1100/103.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
