H-4 | |
---|---|
Role | Helicopter |
National origin | Japan |
Manufacturer | GEN Corporation |
Status | Production suspended (2012) |
Number built | Prototypes only |
The GEN H-4 is a Japanese helicopter under development by GEN Corporation of Nagano. The aircraft is intended to be supplied as a kit for amateur construction. [1] [2]
The H-4 was designed to comply with the United States FAR 103 Ultralight Vehicles rules, including the category's maximum empty weight of 115 kg (254 lb). The aircraft has a standard empty weight of 70 kg (154 lb). It features two contra-rotating main rotors, a single-seat open cockpit without a windshield, four-wheeled landing gear and four twin-cylinder, air-cooled, two-stroke, 10 hp (7 kW) GEN 125-F engines to provide operational redundancy since the aircraft cannot autorotate in the event of a power failure. [1] [2]
The aircraft fuselage is a simple open frame with a seat mounted on it. Its two coaxial, contra-rotating two-bladed rotors have diameters of 4 m (13.1 ft). The main rotors are both of fixed pitch design, with no articulation in any axis. Steering is accomplished by pivoting the rotor head on a gimbal using a control handle, in a similar manner to a weight shift hang glider. Climb and descent is controlled by increasing and decreasing the throttle. The aircraft lacks a tail rotor, as the coaxial, contra-rotating main rotors produce zero net torque. Yawing motion is produced and controlled by electronic gyroscopically-controlled differential electric braking of the main rotors. With its empty weight of 70 kg (154 lb) and a gross weight of 220 kg (485 lb) the H-4 has a useful load of 150 kg (331 lb). With full fuel of 19 litres (4.2 imp gal; 5.0 US gal) the payload is 136 kg (300 lb). [1] [2]
The company indicated that it had suspended production plans by 2012 due to lack of dealers outside Japan and put the cost of a single H-4 at ¥7,500,000.00 (about US$80,887.59 in 2013). The company stated that it could build the aircraft economically only in lots of ten and at a discounted rate only in lots of one hundred. To facilitate future production, the company indicated that it was "looking for sponsors, investors and partners". [3]
On 29 June 2000, the prototype H-4, registered JX0076, was on a test flight at the company plant in Matsumoto-City, Nagano. The pilot was hovering, when the H-4 was hit by a wind gust and contacted the building, 40 m (131 ft) to the northwest and then impacted the ground. The pilot was injured and the airframe damaged. [4] [5]
Data from Bayerl, Tacke and helistart.com [1] [2] [6]
General characteristics
Performance
The Club ULM Rotor Ptenets-2 is a Russian ultralight aircraft, designed and produced by Club ULM Rotor of Kumertau, Bashkortostan. The aircraft is supplied complete and ready-to-fly.
The Airbet Girabet is a family of Spanish autogyros, designed and produced by Airbet of Barcelona. They are all supplied as complete ready-to-fly-aircraft.
The AutoGyro MT-03 is a German autogyro, designed and produced by AutoGyro GmbH of Hildesheim. The aircraft is supplied as a complete ready-to-fly-aircraft.
The Chayair Sycamore is a South African autogyro, designed and produced by Chayair of Musina. The aircraft is supplied as a kit for amateur construction or as a complete ready-to-fly-aircraft.
The ELA 07 is a series of Spanish autogyros, designed and produced by ELA Aviación of Córdoba, Andalusia. The aircraft are supplied complete and ready to fly.
The Gyro-Kopp-Ters Midnight Hawk is an American autogyro, designed by Bob and Arden Kopp and produced by their company, Gyro-Kopp-Ters of Lake City, Florida. The aircraft is supplied as a kit for amateur construction or as a complete ready-to-fly-aircraft.
The Gyro-Kopp-Ters Twin Eagle is an American autogyro, designed by Bob and Arden Kopp and produced by their company, Gyro-Kopp-Ters of Lake City, Florida. The aircraft is supplied as a kit for amateur construction or as a complete ready-to-fly-aircraft.
The GyroTec DF02 is a German autogyro, designed and produced by GyroTec Michael Obermaier of Wörth am Rhein. The DF02 is supplied as complete ready-to-fly-aircraft.
The Rotortec Cloud Dancer II is a German autogyro, designed by Jochen Steinbeck and produced by Rotortec of Görisried, Allgäu. The aircraft was first shown at AERO Friedrichshafen in 2009 and is supplied as a complete ready-to-fly-aircraft.
The Kinney HRH is an American helicopter that was designed by Robert Kinney and produced by Vortech, Inc in the form of plans for amateur construction. The aircraft was first shown at Sun 'n Fun in 2002.
The Phoenix Skyblazer is an American helicopter that was designed by the Nolan brothers and produced by Phoenix Rotorcraft of Fallston, Maryland and more recently Louisburg, North Carolina. When it was available the aircraft was supplied as a complete ready-to-fly-aircraft.
The Ace Magic is an Indian ultralight trike, designed by John Penry-Evans and produced by Ace Aviation of Tamil Nadu. The aircraft is supplied as a complete ready-to-fly-aircraft.
The Aviomania G2SA Genesis Duo is a Cypriot autogyro designed in 2007 by Nicolas Karaolides and produced by Aviomania of Larnaca. The aircraft is supplied as a complete ready-to-fly-aircraft or as a kit for amateur construction.
The Trixy Trixformer is an Austrian roadable aircraft autogyro/electric motorcycle designed and produced by Trixy Aviation Products of Dornbirn, introduced in 2014. The vehicle is supplied complete and ready-to-fly.
The Aero Eli Servizi Yo-Yo 222 is an Italian helicopter designed and produced by Aero Eli Servizi of L'Aquila. The aircraft is supplied complete and ready-to-fly.
The Dynali H3 EasyFlyer, now known as the Sport, is a Belgian helicopter designed and produced by the Dynali of the Thines district of Nivelles. The aircraft is supplied complete and ready-to-fly-aircraft or as a kit for amateur construction.
The EDM Aerotec CoAX 2D/2R is a series of German coaxial main rotor helicopters designed and produced by EDM Aerotec of Geisleden. The aircraft is supplied complete and ready-to-fly.
The Innovator Mosquito Air is a Canadian helicopter produced by Innovator Technologies of Rockyview, Alberta. The aircraft is supplied as a kit for amateur construction.
The IRI T22B is an Italian helicopter that was designed and produced by Italian Rotors Industries of Aprilia, Lazio. Now out of production, when it was available the aircraft was supplied complete and ready-to-fly.
The Rotorschmiede VA115 is a German helicopter, designed and produced by Rotorschmiede GmbH of Munich, introduced at the AERO Friedrichshafen airshow in 2015. The aircraft is supplied complete and ready-to-fly.