Jointed-boiler locomotive

Last updated January 20, 2024

A jointed-boiler locomotive was a variant of the Mallet articulated locomotive, in which a flexible coupling was introduced midway along the length of the boiler casing, which allowed the boiler to bend laterally when the locomotive was on curved track.

Six such locomotives, all of 2-6-6-2 wheel arrangement, were built for the Atchison, Topeka & Santa Fe Railroad in 1910 and 1911. The first one built, number 1157, was assembled by the AT&SF in their Topeka shops from two 2-6-2’s (numbers 1051 and 1125). All the rest were built new by Baldwin Locomotive Works.^[1]^[2]

Design

In a conventional Mallet, the rigid boiler is fixed to the rearmost of the two engine frames, with the front of the boiler supported on a sliding bearing over the pivoting front engine such that when the locomotive traverses a curved track, the front (smokebox) end of the boiler overhangs toward the outside of the curve. The jointed boiler, with the front half rigidly fixed to the front engine, eliminated this overhang. This new design was intended to reduce track wear, especially on curves where the outer rail carried a greater load, and to improve the riding characteristics of the locomotive.

Construction

The two boiler sections served different functions: The rearmost section with the firebox generated and superheated the steam. The forward section contained a reheater (for low-pressure steam serving the front engine), feedwater heater and smokebox. The large flexible joint in the boiler casing carried only combustion gases, at or slightly below atmospheric pressure. Steam and water to the front section were delivered by pipes external to the main casing, with pivoting elbows in high-pressure steam lines, and hoses in water lines, as flexible connections.^[2]

Two designs of the large flexible coupling were used:

A double ball joint assembly consisting of cast iron sleeves, fitted one within the other and provided with compression straps to keep the joints air-tight while allowing lateral movement.
A bellows joint, similar to a concertina, consisted of several pairs of concentric tapered steel rings, each riveted to its neighbor along alternating inside and outside edges. This design proved less successful because coal cinders would accumulate in the folds and force the seams open when the bellows was compressed. These were soon replaced with ball joints.

Performance

The locos worked well enough that they remained in service for 15 to 18 years, but the hoped-for improvements in riding and track wear were not as good as had been hoped. The complicated construction required high maintenance, and no further examples were built.^[3] Jointed boilers were however included in Baldwin's patented but unbuilt 1913 proposals for massive 2-8-8-8-8-2 quadruplex and 2-8-8-8-8-8-2 quintuplex locomotives.^[4]

Related Research Articles

A steam locomotive is a locomotive that provides the force to move itself and other vehicles by means of the expansion of steam. It is fuelled by burning combustible material to heat water in the locomotive's boiler to the point where it becomes gaseous and its volume increases 1,700 times. Functionally, it is a steam engine on wheels.

<span class="mw-page-title-main">Mallet locomotive</span> Articulated locomotive with compound steam power

A Mallet locomotive is a type of compound articulated steam locomotive, invented by the Swiss engineer Anatole Mallet (1837–1919).

Main components found on a typical steam locomotive include:

An articulated locomotive is a steam locomotive with one or more engine units that can move independently of the main frame. Articulation allows the operation of locomotives that would otherwise be too large to negotiate a railroad's curves, whether mainlines or special lines with extreme curvature such as logging, industrial, or mountain railways.

A Meyer locomotive is a type of articulated locomotive. The design was never as popular as the Garratt or Mallet locomotives. It can be best regarded as 19th Century competition for the early compound Mallet and also the Fairlie articulated designs. Most single cab modern trains are of a similar design such as power cars, freight diesel locomotives, and some passenger locomotives.

The LNER W1 No. 10000 was an experimental steam locomotive fitted with a high pressure water-tube boiler. Nigel Gresley was impressed by the results of using high-pressure steam in marine applications and so in 1924 he approached Harold Yarrow of shipyard and boilermakers Yarrow & Company of Glasgow to design a suitable boiler for a railway locomotive, based on Yarrow's design.

A triplex locomotive was a steam locomotive that divided the driving force on its wheels by using three pairs of cylinders to drive three sets of driving wheels. Any such locomotive will inevitably be articulated. All triplex locomotives built were of the Mallet type, but with an extra set of driving wheels under the tender. The concept was extended to locomotives with four, five or six sets of drive wheels. However, these locomotives were never built, except for one quadruplex locomotive in Belgium.

The South African Railways Class MA 2-6-6-0 of 1909 was a steam locomotive from the pre-Union era in the Natal Colony.

The South African Railways Class MC 2-6-6-0 of 1912 was a steam locomotive.

The South African Railways Class MD 2-6-6-2 of 1910 was a steam locomotive from the pre-Union era in Transvaal.

The South African Railways Class ME 2-6-6-2 of 1912 was a steam locomotive.

The South African Railways Class FC 2-6-2+2-6-2 of 1925 was an articulated steam locomotive.

The South African Railways Class HF 2-8-2+2-8-2 of 1927 was an articulated steam locomotive.

The South African Railways Class U 2-6-2+2-6-2 of 1927 was an articulated steam locomotive.

The South African Railways Class GH 4-6-2+2-6-4 of 1928 was an articulated steam locomotive.

The South African Railways Class GA 2-6-0+0-6-2 of 1921 was an articulated steam locomotive.

The South African Railways Class GM 4-8-2+2-8-4 of 1938 was an articulated steam locomotive.

The Cape Government Railways Kitson-Meyer 0-6-0+0-6-0 of 1903 was a South African steam locomotive from the pre-Union era in the Cape of Good Hope.

The MÁV class 601 is a class of Hungarian four cylinder Mallet -type locomotives, which was designed to haul long and very heavy cargo on very steep railway tracks. With their 22.5 meter length and 2200 KW power, they were the largest and most powerful steam locomotives which have ever built before the First World War in Europe.

A multiplex locomotive is a steam locomotive that divides the driving force on its wheels by using multiple pairs of cylinders to drive multiple driving wheel set groups. Such a locomotive will necessarily articulated if it has more than two sets of driving wheels. There were locomotive projects with three, four, five or six sets of drive wheels. However, these locomotives were never built, except for four triplex locomotives in the United States and one quadruplex locomotive in Belgium.

References

↑ J. Parker Lamb, “Perfecting the American Steam Locomotive”, Indiana University Press 2003, ISBN 0-253-34219-8
1 2 "Atchison, Topeka & Santa Fe 2-6-6-2 "Mallet Mogul" Locomotives in the USA". www.steamlocomotive.com.
↑ "The Jointed-Boiler Locomotives," Trains magazine, February 1945
↑ ”What Might Have Been,” Trains Magazine, August 1951

This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.

[1] J. Parker Lamb, “Perfecting the American Steam Locomotive”, Indiana University Press 2003, ISBN 0-253-34219-8

[auto-2] 1 2 "Atchison, Topeka & Santa Fe 2-6-6-2 "Mallet Mogul" Locomotives in the USA". www.steamlocomotive.com.

[3] "The Jointed-Boiler Locomotives," Trains magazine, February 1945

[4] ”What Might Have Been,” Trains Magazine, August 1951

[1]

[2]

[3]

[4]