LED stage lighting is a stage lighting technology that uses light-emitting diodes (LEDs) as a light source. LED instruments are an alternative to traditional stage lights which use halogen lamp or high-intensity discharge lamps. Like other LED instruments, they have high light output with lower power consumption.
LED stage lights come in three main types. PAR cans, striplights [1] and 'moving head' types[ citation needed ]. In LED PAR cans, a round printed circuit board with LEDs mounted on is used in place of a PAR lamp. Moving head types can either be a bank of LEDs mounted on a yoke or more conventional moving head lights with the bulb replaced with an LED bank.[ citation needed ]
In fact, there is no such thing as an LED PAR can - it is a misnomer possibly attributed to Chinese manufacturers[ citation needed ]. As there is no Parabolic Aluminised Reflector in an LED 'PAR', they would be more accurately referred to as 'LED flood lights'.
Many LED fixtures are now made using a small number of high-output diodes that allow the beam to be focused on a "hard edge", allowing full use of gobo/beam effects.
LED instruments can and have been used to replace any conventional lighting fixture, and some shows, such as Radiohead's 2008 tour, have used only LED lighting instruments. [2] However, most shows use LEDs only for lighting cycloramas, or as top, side or back light. They can also be used as 'audience blinders' (lights pointed directly at the audience from a low angle).
LED instruments can contain a number of different coloured LEDs, often red, green and blue, and different light output colours can be achieved by adjusting the intensity of each LED color group. LED instruments should have a long service life relative to other options, without the expense of colour gel or replacement lamps.
LED instruments are increasingly used for live music events, most notably festivals where they are more visible than conventional lighting under daylight. LED instruments were prominently used for the Live Earth festival as they are regarded as more environmentally friendly as fixture for fixture they use far less power than other lighting.
Another advantage of LED instruments is that they can be controlled directly using DMX and do not require additional dimmers; the intensity of the LEDs being adjusted by circuitry on board the fixture. Because of their low power consumption several units can be daisy chained to one power supply. [3]
Due to low heat output, LED instruments can be used in areas where the high amount of heat conventional stage fixtures put off would not be ideal. For this reason, LED instruments are used to light ice sculptures, especially when lighting the sculptures from within. [4]
 |  |
| A comparison of two American DJ 64 LED Pro fixtures vs a single PAR-54 GE 300 watt medium flood incandescent. | |
LED instruments cannot be used to create a hard-edged beam, which is needed for gobos and other effects which require the use of an ellipsoidal reflector spotlight, [3] though LED fixtures are now made that through the use of a small number of high-output diodes now allow the beam to be focused to a "hard edge", allowing full use of gobo/beam effects. Because color mixing is done using three or more colors of LEDs, mixed colors will have multiple edges to shadows where different colors are showing; however, several manufacturers have introduced instruments that group three or more LEDs behind a single lens to make the multiple shadow lines less noticeable.
Stage lighting is the craft of lighting as it applies to the production of theater, dance, opera, and other performance arts. Several different types of stage lighting instruments are used in this discipline. In addition to basic lighting, modern stage lighting can also include special effects, such as lasers and fog machines. People who work on stage lighting are commonly referred to as lighting technicians or lighting designers.
A halogen lamp is an incandescent lamp consisting of a tungsten filament sealed in a compact transparent envelope that is filled with a mixture of an inert gas and a small amount of a halogen, such as iodine or bromine. The combination of the halogen gas and the tungsten filament produces a halogen-cycle chemical reaction, which redeposits evaporated tungsten on the filament, increasing its life and maintaining the clarity of the envelope. This allows the filament to operate at a higher temperature than a standard incandescent lamp of similar power and operating life; this also produces light with higher luminous efficacy and color temperature. The small size of halogen lamps permits their use in compact optical systems for projectors and illumination. The small glass envelope may be enclosed in a much larger outer glass bulb, which has a lower temperature, protects the inner bulb from contamination, and makes the bulb mechanically more similar to a conventional lamp.
Lighting or illumination is the deliberate use of light to achieve practical or aesthetic effects. Lighting includes the use of both artificial light sources like lamps and light fixtures, as well as natural illumination by capturing daylight. Daylighting is sometimes used as the main source of light during daytime in buildings. This can save energy in place of using artificial lighting, which represents a major component of energy consumption in buildings. Proper lighting can enhance task performance, improve the appearance of an area, or have positive psychological effects on occupants.
A flashlight or electric torch, usually shortened to torch, is a portable hand-held electric lamp. Formerly, the light source typically was a miniature incandescent light bulb, but these have been displaced by light-emitting diodes (LEDs) since the early 2000s. A typical flashlight consists of the light source mounted in a reflector, a transparent cover to protect the light source and reflector, a battery, and a switch, all enclosed in a case.
Bicycle lighting is illumination attached to bicycles whose purpose above all is, along with reflectors, to improve the visibility of the bicycle and its rider to other road users under circumstances of poor ambient illumination. A secondary purpose is to illuminate reflective materials such as cat's eyes and traffic signs. A third purpose may be to illuminate the roadway so that the rider can see the way ahead. Serving the latter purposes require much more luminous flux and thus more power.
Ellipsoidal reflector spot is the name for a type of stage lighting instrument, named for the ellipsoidal reflector used to collect and direct the light through a barrel that contains a lens or lens train. The optics of an ERS instrument are roughly similar to those of a 35 mm slide projector.
In stage lighting, an ellipsoidal reflector floodlight, better known as a scoop, is a large, simple lighting fixture with a dome-like reflector, large high-wattage lamp and no lens. It consists almost entirely of a lamp in the center of a big curved metal dome that acts as a reflector. The result is a wide, soft-edged pool of light good for general lighting. However, since scoop lights do not have a mechanism for cutting down the size of their beam, they are rarely used for more specific lighting needs.
A light fixture, light fitting, or luminaire is an electrical lighting device containing one or more light sources, such as lamps, and all the accessory components required for its operation to provide illumination to the environment. All light fixtures have a fixture body and one or more lamps. The lamps may be in sockets for easy replacement—or, in the case of some LED fixtures, hard-wired in place.
A parabolic aluminized reflector lamp is a type of electric lamp that is widely used in commercial, residential, and transportation illumination. It produces a highly directional beam. Usage includes theatrical lighting, locomotive headlamps, aircraft landing lights, and residential and commercial recessed lights.
Intelligent lighting refers to lighting that has automated or mechanical abilities beyond those of conventional, stationary illumination. Although the most advanced intelligent lights can produce extraordinarily complex effects, the intelligence lies with the human lighting designer, control system programmer, or the lighting operator, rather than the fixture itself. For this reason, intelligent lighting (ILS) is also known as automated lighting, moving lights, moving heads, or simply movers.
Stage lighting instruments are used in stage lighting to illuminate theatrical productions, concerts, and other performances taking place in live performance venues. They are also used to light television studios and sound stages.
In theatre, an electrician is a person who works with the various aspects of lighting. Some of the positions among electricians include the lighting supervisor, master electrician, deck electrician, light board operator, moving light programmer, followspot operator, as well as simply electricians. This group is generally known as the "Electrics" Department or LX Department.
A grow light is an electric light that can help plants grow. Grow lights either attempt to provide a light spectrum similar to that of the sun, or to provide a spectrum that is more tailored to the needs of the plants being cultivated. Outdoor conditions are mimicked with varying colour temperatures and spectral outputs from the grow light, as well as varying the intensity of the lamps. Depending on the type of plant being cultivated, the stage of cultivation, and the photoperiod required by the plants, specific ranges of spectrum, luminous efficacy and color temperature are desirable for use with specific plants and time periods.
An LED lamp or LED light is an electric light that produces light using light-emitting diodes (LEDs). LED lamps are significantly more energy-efficient than equivalent incandescent lamps and fluorescent lamps. The most efficient commercially available LED lamps have efficiencies exceeding 200 lumens per watt (lm/W) and convert more than half the input power into light. Commercial LED lamps have a lifespan several times longer than both incandescent and fluorescent lamps.
The SeaChanger Color Engine is an electro-mechanical device that is used to control light color in entertainment-industry lighting applications. The unit employs four overlapped color filter wheels, inserted into a light beam near its source, to produce colored light. This is in contrast to color scrollers, which insert color filter ribbons into a light beam. The color engine, which was released by Ocean Thin Films in 2005, is designed to fit into the Source Four lighting instrument made by Electronic Theatre Controls.
Vari-Lite is a brand of automated, variable-colour stage lighting systems. Their intelligent lighting fixtures are commonly used in theatre, concerts, television, film and corporate events.
An LED street light or road light is an integrated light-emitting diode (LED) light fixture that is used for street lighting.
DJ lighting is a variant of stage lighting that is used by mobile DJs and in nightclubs. DJ lighting is generally used by mobile disco DJs and in most modern nightclubs and many late-night bars.
Stage lighting accessories are components manufactured for conventional (non-automated) stage lighting instruments. Most conventional fixtures are designed to accept a number of different accessories designed to assist in the modification of the output. These accessories are intended to either provide relatively common functionality not originally provided in a fixture, or to extend the versatility of a lighting instrument by introducing features. Other accessories have been designed to overcome limitations or difficulties some fixtures present in specific applications.
A dive light is a light source carried by an underwater diver to illuminate the underwater environment. Scuba divers generally carry self-contained lights, but surface supplied divers may carry lights powered by cable supply.