MW 50

Last updated

MW 50 (Methanol-Wasser 50) was a 50-50 mixture of methanol and water (German: Wasser) that was often sprayed into the supercharger of World War II aircraft engines primarily for its anti-detonation effect, allowing the use of increased boost pressures. Secondary effects were cooling of the engine and charge cooling. Higher boost was only effective at altitudes below the full-throttle height, where the supercharger could still provide additional boost pressure that was otherwise wasted, while the smaller secondary effects were useful even above that altitude.

Contents

Composition

MW 50 is something of a misnomer, as it is actually a mixture of three fluids: 50% methanol acting primarily to achieve optimum anti-detonant effect, secondarily as an anti-freeze; 49.5% water; and 0.5% Schutzöl 39, an oil-based anti-corrosion additive. The similar MW 30 increased the water to 69.5% and decreased methanol to 30%. [1] This increased the cooling performance but made it easier to freeze at -18 degrees C as opposed to -50 C for MW 50). As a result, this mixture was intended to be used for lower-altitude missions. EW 30 and EW 50 mixtures also existed, which substituted methanol with ethanol; in emergency, pure water could be used.

Effect

The effect of MW 50 injection could be dramatic. Simply turning on the system allowed the engine to pull in more air due to the charge cooling effect, boosting performance by about 100 hp (75 kW) on the BMW 801 and DB 605. However, the MW 50 also allowed the supercharger to be run at much higher boost levels as well, for a combined increase of 500 hp (370 kW). At sea level, this allowed the 1,600 hp (1,200 kW) engine to run at over 2,000 hp (1,500 kW). MW 50 was fully effective up to about 6,000 m (20,000 ft), above which it added only about 4% extra power, due largely to charge cooling.

Time limits

The increased power could be used for a maximum of 10 minutes at a time, much like the American war emergency power setting for their own aircraft, with at least five minutes between each application. [2] Aircraft generally carried enough MW 50 for about two ten-minute periods of use, allowing them to increase their climb rate and level speed in combat for interception missions.

Applications

Fittings for MW 50 first appeared on the BMW 801D in 1942, but it never went into production for this engine because the cylinder heads developed micro-cracks when MW 50 was used. Instead, the DB 605-engined later versions of the Messerschmitt Bf 109 were fitted with an MW 50 injection system, beginning in early 1944. Later engine designs all included the fittings as well, notably the Junkers Jumo 213, which relied on it to increase non-boosted performance and tune the supercharger for higher altitudes.

Other systems

MW 50 was not the only charge cooling system to be used by the Germans. Some engines dedicated to high altitude included an intercooler instead, as they would be needing the cooling for longer periods of time. The 801D also included the ability to spray gasoline into the supercharger [2] (the Erhöhte Notleistung [Increased Emergency Performance] system), in place of the MW 50. While this was not as effective, it did increase boost without the complexity of the additional tanking and plumbing. Additionally, many of the late-war engines also included a system for high-altitude boost, GM-1, which was intended to add oxygen to the fuel/air mix by injecting nitrous oxide into the supercharger [2] instead of employing higher boost levels – the Jumo 213E inverted V12 on the Ta 152H could "sprint" with both boost systems engaged to airspeeds of well over 560 km/h (350 mph) at low altitudes.

See also

Related Research Articles

Turbocharger Forced induction device for internal combustion engines

A turbocharger, colloquially known as a turbo, is a turbine-driven, forced induction device that increases an internal combustion engine's power output by forcing extra compressed air into the combustion chamber. This improvement over a naturally aspirated engine's power output is because the compressor can force more air—and proportionately more fuel—into the combustion chamber than atmospheric pressure alone.

Rolls-Royce Merlin Aircraft engine family by Rolls-Royce

The Rolls-Royce Merlin is a British liquid-cooled V-12 piston aero engine of 27-litres capacity. Rolls-Royce designed the engine and first ran it in 1933 as a private venture. Initially known as the PV-12, it was later called Merlin following the company convention of naming its piston aero engines after birds of prey.

BMW 801

The BMW 801 was a powerful German 41.8-litre (2,550 cu in) air-cooled 14-cylinder-radial aircraft engine built by BMW and used in a number of German Luftwaffe aircraft of World War II. Production versions of the twin-row engine generated between 1,560 and 2,000 PS. It was the most produced radial engine of Germany in World War II with more than 61,000 built.

Forced induction is the process of delivering compressed air to the intake of an internal combustion engine. A forced induction engine uses a gas compressor to increase the pressure, temperature and density of the air. An engine without forced induction is considered a naturally aspirated engine.

Junkers Jumo 205

The Junkers Jumo 205 aircraft engine was the most famous of a series of aircraft diesel engines that were the first, and for more than half a century, the only successful aviation diesel powerplants. The Jumo 204 first entered service in 1932. Later engines of this type comprised the experimental Jumo 206 and Jumo 208, with the Jumo 207 produced in some quantity for the Junkers Ju 86P and -R high-altitude reconnaissance aircraft, and the 46-meter wingspan, six-engined Blohm & Voss BV 222 Wiking flying boat. All three of these variants differed in stroke and bore and supercharging arrangements. In all, more than 900 of these engines were produced, in the 1930s and through most of World War II.

Junkers Jumo 222

The Jumo 222 was a German high-power multiple-bank in-line piston aircraft engine from Junkers, designed under the management of Ferdinand Brandner of the Junkers Motorenwerke.

Junkers Jumo 211

The Jumo 211 was a German inverted V-12 aircraft engine, Junkers Motoren's primary aircraft engine of World War II. It was the direct competitor to the Daimler-Benz DB 601 and closely paralleled its development. While the Daimler-Benz engine was mostly used in single-engined and twin-engined fighters, the Jumo engine was primarily used in bombers such as Junkers' own Ju 87 and Ju 88, and Heinkel's H-series examples of the Heinkel He 111 medium bomber. It was the most-produced German aero engine of the war, with almost 70,000 examples completed.

Packard V-1650 Merlin Piston aircraft engine

The Packard V-1650 Merlin is a version of the Rolls-Royce Merlin aircraft engine, produced under license in the United States by the Packard Motor Car Company. The engine was licensed to expand production of the Rolls-Royce Merlin for British use. The engine also filled a gap in the U.S. at a time when similarly-powered American-made engines were not available.

Bramo 323

The Bramo 323 Fafnir is a nine-cylinder radial aircraft engine of the World War II era. Based heavily on Siemens/Bramo's earlier experience producing the Bristol Jupiter under license, the Bramo 323 saw limited use.

GM-1 was a system for injecting nitrous oxide into aircraft engines that was used by the Luftwaffe in World War II. This increased the amount of oxygen in the fuel mixture, and thereby improved high-altitude performance. GM-1 was used on a number of modifications of existing fighter designs in order to counter the increasing performance of Allied fighters at higher altitudes.

Junkers Jumo 213

The Junkers Jumo 213 was a World War II-era V-12 liquid-cooled aircraft engine, a development of Junkers Motoren's earlier design, the Jumo 211. The design added two features, a pressurized cooling system that required considerably less cooling fluid which allowed the engine to be built smaller and lighter, and a number of improvements that allowed it to run at higher RPM. These changes boosted power by over 500 hp and made the 213 one of the most sought-after Axis engine designs in the late-war era.

Junkers Jumo 210

The Jumo 210 was Junkers Motoren's first production inverted V12 gasoline aircraft engine, first produced in the early-1930s. Depending on the version it produced between 610 and 730 PS and can be considered a counterpart of the Rolls-Royce Kestrel in many ways. Although originally intended to be used in almost all pre-war designs, rapid progress in aircraft design quickly relegated it to the small end of the power scale by the late 1930s. Almost all aircraft designs switched to the much larger Daimler-Benz DB 600, so the 210 was produced only for a short time before Junkers responded with a larger engine of their own, the Junkers Jumo 211.

Shvetsov ASh-82

The Shvetsov ASh-82 (M-82) is a Soviet 14-cylinder, two-row, air-cooled radial aircraft engine developed from the Shvetsov M-62. The M-62 was the result of development of the M-25, which was a licensed version of the Wright R-1820 Cyclone.

In internal combustion engines, water injection, also known as anti-detonant injection (ADI), can spray water into the incoming air or fuel-air mixture, or directly into the cylinder to cool certain parts of the induction system where "hot points" could produce premature ignition. In jet engines it increases engine thrust at low speeds and at takeoff.

Daimler-Benz DB 605 German aircraft engine

The Daimler-Benz DB 605 is a German aircraft engine built during World War II. Developed from the DB 601, the DB 605 was used from 1942 to 1945 in the Messerschmitt Bf 109 fighter, and the Bf 110 and Me 210C heavy fighters. The DB 610, a coupled "power system" powerplant comprising a pair of side-by-side configured examples of the DB 605, geared together in the front to turn a single output shaft — and which, like the similar DB 606 that it replaced, weighed 1,515 kg — was used in the A-3 and all A-5 variants of Germany's only operational heavy bomber, the Heinkel He 177A.

Daimler-Benz DB 603 German aircraft engine

The Daimler-Benz DB 603 was a German aircraft engine used during World War II. It was a liquid-cooled 12-cylinder inverted V12 enlargement of the DB 601, which was in itself a development of the DB 600. Production of the DB 603 commenced in May 1942, and with a 44.5 liter displacement figure, was the largest displacement inverted V12 aviation engine to be produced and used in front line aircraft of the Third Reich during World War II.

War Emergency Power (WEP) is an American term for a throttle setting on some World War II military aircraft engines. For use in emergency situations, it produced more than 100% of the engine's normal rated power for a limited amount of time, often about five minutes. Similar systems used by non-US forces are now often referred to as WEP as well, although they may not have been at the time, as with the German Luftwaffe's Notleistung and Soviet VVS' forsazh systems.

Supercharger Air compressor for an internal combustion engine

A supercharger is an air compressor that increases the pressure or density of air supplied to an internal combustion engine. This gives each intake cycle of the engine more oxygen, letting it burn more fuel and do more work, thus increasing the power output.

The Focke-Wulf Ta 254 was a proposed German development of the Ta 154 fighter, to have been produced by Focke-Wulf.

References

Notes

  1. Bridgeman 1989, p. 296.
  2. 1 2 3 Bridgeman 1989, p. 297.

Bibliography

  • Bridgman, L, (ed.) (1989) Jane's fighting aircraft of World War II. Crescent. ISBN   0-517-67964-7