 | This article needs additional citations for verification .(January 2021) |
An oil catch tank or oil catch can is a device that is fitted into the cam/crankcase ventilation system on a car. Installing an oil catch tank (can) aims to reduce the amount of oil vapors re-circulated into the intake of the engine.
During normal operation of a car engine, some vapors from the cylinder pass by the piston rings and down into the crankcase. Without ventilation this can pressurize the crankcase and cause issues such as lack of piston ring sealing and damaged oil seals.
To avoid this, manufacturers created a crankcase ventilation system. Originally this was often a very basic setup where a filter was placed on the top of the cam case and the pressure and vapors were vented to atmosphere. This was deemed unacceptable as it allowed fumes and oil mist to be vented out into the atmosphere which caused pollution. It could also cause issues for the occupants of the car as it could be drawn into the inside of the car, which was often unpleasant.
Around 1961 a new design was created. This design routed the crank breather into the intake of the car. This meant that the vapors and oil mist could be burnt and expelled out of the car through the exhaust. Not only was this more pleasant for the car occupants it also meant that oil mist was not released into the air or onto the road in the case of draft tube ventilation systems.
There are two issues that can be caused by routing the crank breather into the intake system of an engine.
The main issue is with the buildup of oil inside the intake piping and manifold. During the normal operation of an engine the excess blow-by and oil vapors from the crank case are allowed to enter the intake system. The oil mist cools and layers the inside of the intake piping and manifold. Over time this layer can build up and thick sludge can accumulate.
This has been made worse with the introduction of the exhaust gas recirculation (EGR) system on more modern cars. The oil vapors can mix with the re-circulated exhaust gasses and soot which then builds up on the intake manifold and valves etc. This layer over time hardens and thickens repeatedly. It will then begin to clog up the throttle body, swirl flaps, or even the intake valves on direct injected engines. [1] [ verification needed ]
Having a buildup of sludge can cause lower performance due to the limiting effect it has on the air flow to the engine. If the buildup becomes excessive on the throttle body it can cause poor idling as it can block the air flow whilst the throttle plate is shut.
Fitting a catch tank (can) will reduce the amount of oil vapor reaching the intake tract and combustion chamber. Without the oil vapor the soot from the EGR valve will not congeal so much on the intake which will keep the intake from becoming clogged.
Another issue that has been raised as a possible problem with allowing oil vapor into the intake is the chance of pre-detonation (Knock) caused by the oil vapor exploding during the compression cycle of the engine. This has become more of an issue as more and more cars have started to run high boost levels and high compression ratios. The higher the compression and boost the more likely the oil is to start to burn (Pre-Detonate) Fitting an oil catch tank (can) in the breather pipe will stop the oil vapors from reaching the combustion chamber. This will reduce the knock effect.
An oil catch tank (can) is fitted in line of the crank case breather system. It is placed in between the breather outlet and the intake system. As the crank vapors pass through the catch tank (can) the oil droplets, un-burnt fuel, and water vapor condense and settle in the tank. This stops them from reaching the intake and causing the issues mentioned above.
The best type of catch tank (can) will often have some sort of media inside such as a fine metal mesh or Brillo pad style metal which will create a much larger surface area for the vapors to condense.
Over time the catch tank (can) will fill up with the excess oil and will need to be drained. This is often done by opening a drain plug on the bottom of the tank.
A two-strokeengine is a type of internal combustion engine that completes a power cycle with two strokes of the piston during one power cycle, this power cycle being completed in one revolution of the crankshaft. A four-stroke engine requires four strokes of the piston to complete a power cycle during two crankshaft revolutions. In a two-stroke engine, the end of the combustion stroke and the beginning of the compression stroke happen simultaneously, with the intake and exhaust functions occurring at the same time.
In internal combustion engines, exhaust gas recirculation (EGR) is a nitrogen oxide (NOx) emissions reduction technique used in petrol/gasoline, diesel engines and some hydrogen engines. EGR works by recirculating a portion of an engine's exhaust gas back to the engine cylinders. The exhaust gas displaces atmospheric air and reduces O2 in the combustion chamber. Reducing the amount of oxygen reduces the amount of fuel that can burn in the cylinder thereby reducing peak in-cylinder temperatures. The actual amount of recirculated exhaust gas varies with the engine operating parameters.
The GM Ecotec engine, also known by its codename L850, is a family of all-aluminium inline-four engines, displacing between 1.4 and 2.5 litres. Confusingly, the Ecotec name was also applied to the final DOHC derivatives of the previous GM Family II engine, the architecture was substantially re-engineered for this new Ecotec application produced since 2000. This engine family replaced the GM Family II engine, the GM 122 engine, the Saab H engine, and the Quad 4 engine. It is manufactured in multiple locations, to include Spring Hill Manufacturing, in Spring Hill, Tennessee while the engine block and cylinder heads are cast at Saginaw Metal Casting Operations in Saginaw, Michigan.
The LA engines are a family of pushrod OHV small block 90° V-configured gasoline engines built by Chrysler Corporation. They were factory-installed in passenger vehicles, trucks and vans, commercial vehicles, marine and industrial applications from 1964 through 1991 (318) & 1992 (360). Their combustion chambers are wedge-shaped, rather than polyspherical, as in the predecessor A engine, or hemispherical in the Hemi. LA engines have the same 4.46 in (113 mm) bore spacing as the A engines.
The Chrysler 1.8, 2.0, and 2.4 are inline-4 engines designed originally for the Dodge and Plymouth Neon compact car. These engines were loosely based on their predecessors, the Chrysler 2.2 & 2.5 engine, sharing the same 87.5 mm (3.44 in) bore. The engine was developed by Chrysler with input from the Chrysler-Lamborghini team that developed the Chrysler/Lamborghini Formula 1 V12 engine in the early 1990s.
The LH engine was a series of V6 engines developed by Chrysler Corporation for its LH platform cars. It is a 60-degree V6 designed for front-wheel drive applications, later adapted to rear-wheel drive ones. The 2.7 liter LH engine is based on the SOHC 3.5 L engine, though bore spacing, cylinder bore, stroke, and assembly site are different.
Engine braking occurs when the retarding forces within an internal combustion engine are used to slow down a motor vehicle, as opposed to using additional external braking mechanisms such as friction brakes or magnetic brakes.
In automotive engineering, an inlet manifold or intake manifold is the part of an engine that supplies the fuel/air mixture to the cylinders. The word manifold comes from the Old English word manigfeald and refers to the multiplying of one (pipe) into many.
Manifold vacuum, or engine vacuum in an internal combustion engine is the difference in air pressure between the engine's intake manifold and Earth's atmosphere.
In a piston engine, the crankcase is the housing that surrounds the crankshaft. In most modern engines, the crankcase is integrated into the engine block.
The Toyota S Series engines are a family of straight-4 petrol or CNG engines with displacement from 1.8 L to 2.2 L produced by Toyota Motor Corporation from January 1980 to August 2007. The series has cast iron engine blocks and aluminium cylinder heads.
A crankcase ventilation system removes unwanted gases from the crankcase of an internal combustion engine. The system usually consists of a tube, a one-way valve and a vacuum source.
The Mitsubishi 6B3 engine is a range of all-alloy piston V6 engines developed by Mitsubishi Motors. Currently, only one engine has been developed, a 3.0 L (2,998 cc) V6 first introduced in the North American version of the second generation Mitsubishi Outlander which debuted in October 2006.
The following outline is provided as an overview of and topical guide to automobiles:
Cox model engines are used to power small model airplanes, model cars and model boats. They were in production for more than 60 years between 1945 and 2006. The business is named for founder Leroy M. Cox. He started L.M. Cox Manufacturing Co. Inc, which later became Cox Hobbies Inc., then Cox Products, before being sold to Estes Industries, when it became Cox Models. On February 7, 2009, Estes Industries stopped producing Cox engines and sold all of their remaining inventory – mainly spare parts – to several private buyers from Canada and the US. One of the new owners of the remaining Cox engine and parts inventory has launched a website with an online store.
Mitsubishi MCA stands for Mitsubishi Clean Air, a moniker used in Japan to identify vehicles built with emission control technology. The term was first introduced in Japan, with later introductions internationally. The technology first appeared in January 1973 on the Mitsubishi 4G32A gasoline-powered inline four cylinder engine installed in all Mitsubishi vehicles using the 4G32 engine, and the Saturn-6 6G34 six-cylinder gasoline-powered engine installed in the Mitsubishi Debonair. The technology was installed so that their vehicles would be in compliance with Japanese Government emission regulations passed in 1968.
An internal combustion engine is a heat engine in which the combustion of a fuel occurs with an oxidizer in a combustion chamber that is an integral part of the working fluid flow circuit. In an internal combustion engine, the expansion of the high-temperature and high-pressure gases produced by combustion applies direct force to some component of the engine. The force is typically applied to pistons, turbine blades, a rotor, or a nozzle. This force moves the component over a distance, transforming chemical energy into kinetic energy which is used to propel, move or power whatever the engine is attached to.