This article's lead section contains information that is not included elsewhere in the article. If the information is appropriate for the lead of the article, this information should also be included in the body of the article.(August 2023) ( Learn how and when to remove this template message )
EGR valve the top of box on top of the inlet manifold of a Saab H engine in a 1987 Saab 90
In internal combustion engines, exhaust gas recirculation (EGR) is a nitrogen oxide (NOx) emissions reduction technique used in petrol/gasoline, diesel engines and some hydrogen engines.[1] EGR works by recirculating a portion of an engine's exhaust gas back to the engine cylinders. The exhaust gas displaces atmospheric air and reduces O2 in the combustion chamber. Reducing the amount of oxygen reduces the amount of fuel that can burn in the cylinder thereby reducing peak in-cylinder temperatures. The actual amount of recirculated exhaust gas varies with the engine operating parameters.
In the combustion cylinder, NOx is produced by high-temperature mixtures of atmospheric nitrogen and oxygen, and this usually occurs at cylinder peak pressure. In a spark-ignition engine, an ancillary benefit of recirculating exhaust gases via an external EGR valve is an increase in efficiency, as charge dilution allows a larger throttle position and reduces associated pumping losses. Mazda's turbocharged SkyActivgasoline direct injection engine uses recirculated and cooled exhaust gases to reduce combustion chamber temperatures, thereby permitting the engine to run at higher boost levels before the air-fuel mixture must be enriched to prevent engine knocking.[2]
In a gasoline engine, this inert exhaust displaces some amount of combustible charge in the cylinder, effectively reducing the quantity of charge available for combustion without affecting the air-fuel ratio. In a diesel engine, the exhaust gas replaces some of the excess oxygen in the pre-combustion mixture.[3] Because NOx forms primarily when a mixture of nitrogen and oxygen is subjected to high temperature, the lower combustion chamber temperatures caused by EGR reduces the amount of NOx that the combustion process generates. Gases re-introduced from EGR systems will also contain near equilibrium concentrations of NOx and CO; the small fraction initially within the combustion chamber inhibits the total net production of these and other pollutants when sampled on a time average. Chemical properties of different fuels limit how much EGR may be used. For example methanol is more tolerant to EGR than gasoline.[4]
History
The first EGR systems were crude; some were as simple as an orifice jet between the exhaust and intake tracts which admitted exhaust to the intake tract whenever the engine was running. Difficult starting, rough idling, reduced performance and lost fuel economy inevitably resulted.[5] By 1973, an EGR valve controlled by manifold vacuum opened or closed to admit exhaust to the intake tract only under certain conditions. Control systems grew more sophisticated as automakers gained experience; Volkswagen's "Coolant Controlled Exhaust Gas Recirculation" system of 1973 exemplified this evolution: a coolant temperature sensor blocked vacuum to the EGR valve until the engine reached normal operating temperature.[5] This prevented driveability problems due to unnecessary exhaust induction; NOx forms under elevated temperature conditions generally not present with a cold engine. Moreover, the EGR valve was controlled, in part, by vacuum drawn from the carburetor's venturi, which allowed more precise constraint of EGR flow to only those engine load conditions under which NOx is likely to form.[6] Later, backpressuretransducers were added to the EGR valve control to further tailor EGR flow to engine load conditions. Most modern engines now need exhaust gas recirculation to meet NOx emissions standards. However, recent innovations have led to the development of engines that do not require them. The 3.6 Chrysler Pentastar engine is one example that does not require EGR.[7]
The exhaust gas contains water vapor and carbon dioxide which both have lower heat capacity ratio than air. Adding exhaust gas therefore reduces pressure and temperature during the isentropic compression in the cylinder, thereby lowering the adiabatic flame temperature.
In a typical automotive spark-ignited (SI) engine, 5% to 15% of the exhaust gas is routed back to the intake as EGR. The maximum quantity is limited by the need of the mixture to sustain a continuous flame front during the combustion event; excessive EGR in poorly set up applications can cause misfires and partial burns. Although EGR does measurably slow combustion, this can largely be compensated for by advancing spark timing. The impact of EGR on engine efficiency largely depends on the specific engine design, and sometimes leads to a compromise between efficiency and NOx emissions. In certain types of situations, a properly operating EGR can theoretically increase the efficiency of gasoline engines via several mechanisms:
Reduced throttle losses. The addition of inert exhaust gas into the intake system means that for a given power output, the throttle plate must be opened further, resulting in increased inlet manifold pressure and reduced throttling losses.[8]
Reduced heat rejection. Lowered peak combustion temperatures not only reduces NOx formation, it also reduces the loss of thermal energy to combustion chamber surfaces, leaving more available for conversion to mechanical work during the expansion stroke.
Reduced chemical dissociation. The lower peak temperatures result in more of the released energy remaining as sensible energy near Top Dead Center (TDC), rather than being bound up (early in the expansion stroke) in the dissociation of combustion products. This effect is minor compared to the first two.
EGR is typically not employed at high loads because it would reduce peak power output. This is because it reduces the intake charge density. EGR is also omitted at idle (low-speed, zero load) because it would cause unstable combustion, resulting in rough idle.
Since the EGR system recirculates a portion of exhaust gases, over time the valve can become clogged with carbon deposits, which will prevent it from operating properly. Clogged EGR valves can sometimes be cleaned, but replacement is necessary if the valve is faulty.
Because diesel engines depend on the heat of compression to ignite their fuel, they are fundamentally different from spark-ignited engines. The physical process of diesel-fuel combustion is such that the most complete combustion occurs at the highest temperatures. Unfortunately, the production of nitrogen oxides (NOx) increases at high temperatures. The goal of EGR is thus to reduce NOx production by reducing the combustion temperatures.
In modern diesel engines, the EGR gas is usually cooled with a heat exchanger to allow the introduction of a greater mass of recirculated gas. However, uncooled EGR designs do exist; these are often referred to as hot-gas recirculation (HGR). Cooled EGR components are exposed to repeated, rapid changes in temperatures, which can cause coolant leak and catastrophic engine failure.[9][10]
Unlike spark-ignition engines, diesel engines are not limited by the need for a contiguous flamefront. Furthermore, since diesels always operate with excess air, they benefit (in terms of reduced NOx output) from EGR rates as high as 50%. However, a 50% EGR rate is only suitable when the diesel engine is at idle, since this is when there is otherwise a large excess of air.
Because modern diesel engines often have a throttle, EGR can reduce the need for throttling, thereby eliminating this type of loss in the same way that it does for spark-ignited engines. In a naturally aspirated (i.e. nonturbocharged) engine, such a reduction in throttling also reduces the problem of engine oil being sucked past the piston rings into the cylinder and causing oil-derived carbon deposits there. (This benefit only applies to nonturbocharged engines.)
In diesel engines in particular, EGR systems come with serious drawbacks, one of which is a reduction in engine longevity. For example, because the EGR system routes exhaust gas directly back into the cylinder intake without any form of filtration, this exhaust gas contains carbon particulates. And, because these tiny particles are abrasive, the recirculation of this material back into the cylinder increases engine wear. This is so because these carbon particles will blow by the piston rings (causing piston-cylinder-interface wear in the process) and then end up in the crankcase oil, where they will cause further wear throughout the engine simply because their tiny size passes through typical oil filters. This enables them to be recirculated indefinitely (until the next oil change takes place).[11]
Exhaust gas—which consists largely of nitrogen, carbon dioxide, and water vapor—has a higher specific heat than air, so it still serves to lower peak combustion temperatures. However, adding EGR to a diesel reduces the specific heat ratio of the combustion gases in the power stroke. This reduces the amount of power that can be extracted by the piston, thereby reducing the thermodynamic efficiency.
EGR also tends to reduce the completeness of fuel combustion during the power stroke. This is plainly evident by the increase in particulate emissions that corresponds to an increase in EGR.[12][13]
Particulate matter (mainly carbon and also known as soot) that is not burned in the power stroke represents wasted energy. Because of stricter regulations on particulate matter (PM), the soot-increasing effect of EGR required the introduction of further emission controls in order to compensate for the resulting PM emission increases. The most common soot-control device is a diesel particulate filter (DPF) installed downstream of the engine in the exhaust system. This captures soot but causes a reduction in fuel efficiency due to the back pressure created.
Diesel particulate filters come with their own set of very specific operational and maintenance requirements. Firstly, as the DPF captures the soot particles (which are made far more numerous due to the use of EGR), the DPF itself progressively becomes loaded with soot. This soot must then be burned off, either actively or passively.
At sufficiently high temperatures, the nitrogen dioxide component of NOx emissions is the primary oxidizer of the soot caught in the DPF at normal operating temperatures. This process is known as passive regeneration, and it is only partially effective at burning off the captured soot. And, especially at high EGR rates, the effectiveness of passive regeneration is further reduced. This, in turn, necessitates periodic active regeneration of the DPF by burning diesel fuel directly in the oxidation catalyst in order to significantly increase exhaust-gas temperatures through the DPF to the point where PM is incinerated by the residual oxygen in the exhaust.
Because diesel fuel and engine oil both contain nonburnable (i.e. metallic and mineral) impurities, the incineration of soot (PM) in the DPF leaves behind a residue known as ash. For this reason, after repeated regeneration events, eventually the DPF must either be physically removed and cleaned in a special external process, or it must be replaced.
As noted earlier, the feeding of the low-oxygen exhaust gas into the diesel engine's air intake engenders lower combustion temperatures, thereby reducing emissions of NOx. By replacing some of the fresh air intake with inert gases EGR also allows the engine to reduce the amount of injected fuel without compromising ideal air-fuel mixture ratio, therefore reducing fuel consumption in low engine load situation (for ex. while the vehicle is coasting or cruising). Power is not reduced by EGR at any times, as EGR is not employed in high load engine situations. This allows engines to still deliver maximum power when needed, but lower fuel consumption despite large cylinder volume when partial load is sufficient to meet the power needs of the car and the driver.
EGR has nothing to do with oil vapor re-routing from a positive crankcase ventilation system (PCV) system, as the latter is only there to reduce oil vapor emissions, and can be present on engines with or without any EGR system. However, the tripartite mixture resulting from employing both EGR and PCV in an engine (i.e. exhaust gas, fresh air, and oil vapour) can cause the buildup of sticky tar in the intake manifold and valves. This mixture can also cause problems with components such as swirl flaps, where fitted. (These problems, which effectively take the form of an undesirable positive-feedback loop, will worsen as the engine ages. For example, as the piston rings progressively wear out, more crankcase oil will get into the exhaust stream. Simultaneously, more fuel and soot and combustion byproducts will gain access to the engine oil.)
The end result of this recirculation of both exhaust gas and crankcase oil vapour is again an increase in soot production, which however is effectively countered by the DPF, which collects these and in the end will burn those unburnt particles during regeneration, converting them into CO2 and water vapour emissions, that - unlike NOx gases - have no negative health effects.[14]
Modern cooled EGR systems help reduce engine wear by using the waste heat recouped from the recirculated gases to help warm the coolant and hence the engine block faster to operating temperature. This also helps lower fuel consumption through reducing the time after cold starts during which the engine controller has to inject somewhat larger amounts of fuel into the cylinders to counter the effects of fuel vapor condensation on cylinder walls and lowered combustion effectiveness because of the engine block still being below ideal operating temperature. Lowering combustion temperatures also helps reducing the oxidization of engine oil, as the most significant factor affecting that is exposure of the oil to high temperatures.[15]
Although engine manufacturers have refused to release details of the effect of EGR on fuel economy, the EPA regulations of 2002 that led to the introduction of cooled EGR were associated with a 3% drop in engine efficiency, thus bucking the trend of a 0.5% annual increase.[16]
Heywood, John B., "Internal Combustion Engine Fundamentals," McGraw Hill, 1988.
van Basshuysen, Richard, and Schäfer, Fred, "Internal Combustion Engine Handbook," SAE International, 2004.
"Bosch Automotive Handbook," 3rd Edition, Robert Bosch GmbH, 1993.
Alger, Terry (2010). "Clean and Cool"(PDF). Technology Today. 31 (2). San Antonio, Texas: Southwest Research Institute: 10–13. ISSN1528-431X. Retrieved 8 April 2017.
Sileghem, Louis; Van De Ginste, Maarten; Sierens, Roger; Verhelst, Sebastian; Vancoillie, Jeroen (2011). "Methanol as a Fuel for Modern Spark-Ignition Engines: Efficiency Study". Department of Flow, Heat and Combustion Mechanics. Ghent, Belgium: Ghent University. Retrieved 19 March 2019– via Research Gate.
Related Research Articles
In engineering, the Miller cycle is a thermodynamic cycle used in a type of internal combustion engine. The Miller cycle was patented by Ralph Miller, an American engineer, U.S. patent 2,817,322 dated Dec 24, 1957. The engine may be two- or four-stroke and may be run on diesel fuel, gases, or dual fuel. It uses a supercharger to offset the performance loss of the Atkinson cycle.
A two-strokeengine is a type of internal combustion engine that completes a power cycle with two strokes of the piston in one revolution of the crankshaft. A four-stroke engine requires four strokes of the piston to complete a power cycle in two crankshaft revolutions. In a two-stroke engine, the end of the combustion stroke and the beginning of the compression stroke happen simultaneously, with the intake and exhaust functions occurring at the same time.
A four-strokeengine is an internal combustion (IC) engine in which the piston completes four separate strokes while turning the crankshaft. A stroke refers to the full travel of the piston along the cylinder, in either direction. The four separate strokes are termed:
Intake: Also known as induction or suction. This stroke of the piston begins at top dead center (T.D.C.) and ends at bottom dead center (B.D.C.). In this stroke the intake valve must be in the open position while the piston pulls an air-fuel mixture into the cylinder by producing a partial vacuum in the cylinder through its downward motion.
Compression: This stroke begins at B.D.C, or just at the end of the suction stroke, and ends at T.D.C. In this stroke the piston compresses the air-fuel mixture in preparation for ignition during the power stroke (below). Both the intake and exhaust valves are closed during this stage.
Combustion: Also known as power or ignition. This is the start of the second revolution of the four stroke cycle. At this point the crankshaft has completed a full 360 degree revolution. While the piston is at T.D.C. the compressed air-fuel mixture is ignited by a spark plug or by heat generated by high compression, forcefully returning the piston to B.D.C. This stroke produces mechanical work from the engine to turn the crankshaft.
Exhaust: Also known as outlet. During the exhaust stroke, the piston, once again, returns from B.D.C. to T.D.C. while the exhaust valve is open. This action expels the spent air-fuel mixture through the exhaust port.
A catalytic converter is an exhaust emission control device which converts toxic gases and pollutants in exhaust gas from an internal combustion engine into less-toxic pollutants by catalyzing a redox reaction. Catalytic converters are usually used with internal combustion engines fueled by gasoline or diesel, including lean-burn engines, and sometimes on kerosene heaters and stoves.
The Duramax V8 engine is a family of 6.6-liter diesel V8 engines produced by DMAX, a wholly owned subsidiary of General Motors in Moraine, Ohio. The Duramax block and heads are supplied from reliable vendors of General Motors. This engine was initially installed in 2001 Chevrolet and GMC trucks, and has since become an option in pickups, vans, and medium-duty trucks. In 2006, production at Moraine was reportedly limited to approximately 200,000 engines per year. On May 9, 2007, DMAX announced the production of the 1,000,000th Duramax V8 at its Moraine facility, followed by the 2,000,000th on March 24, 2017.
Power Stroke, also known as Powerstroke or PowerStroke, is the name used by a family of diesel engines for trucks produced by Ford Motor Company and Navistar International for Ford products since 1994. Along with its use in the Ford F-Series, applications include the Ford E-Series, Ford Excursion, and Ford LCF commercial truck. The name was also used for a diesel engine used in South American production of the Ford Ranger.
Engine braking occurs when the retarding forces within an internal combustion engine are used to slow down a motor vehicle, as opposed to using additional external braking mechanisms such as friction brakes or magnetic brakes.
Diesel exhaust is the gaseous exhaust produced by a diesel type of internal combustion engine, plus any contained particulates. Its composition may vary with the fuel type or rate of consumption, or speed of engine operation, and whether the engine is in an on-road vehicle, farm vehicle, locomotive, marine vessel, or stationary generator or other application.
Lean-burn refers to the burning of fuel with an excess of air in an internal combustion engine. In lean-burn engines the air–fuel ratio may be as lean as 65:1. The air / fuel ratio needed to stoichiometrically combust gasoline, by contrast, is 14.64:1. The excess of air in a lean-burn engine emits far less hydrocarbons. High air–fuel ratios can also be used to reduce losses caused by other engine power management systems such as throttling losses.
Gasoline direct injection (GDI), also known as petrol direct injection (PDI), is a mixture formation system for internal combustion engines that run on gasoline (petrol), where fuel is injected into the combustion chamber. This is distinct from manifold injection systems, which inject fuel into the intake manifold.
Homogeneous Charge Compression Ignition (HCCI) is a form of internal combustion in which well-mixed fuel and oxidizer are compressed to the point of auto-ignition. As in other forms of combustion, this exothermic reaction produces heat that can be transformed into work in a heat engine.
In internal combustion engines, water injection, also known as anti-detonant injection (ADI), can spray water into the incoming air or fuel-air mixture, or directly into the combustion chamber to cool certain parts of the induction system where "hot points" could produce premature ignition. In jet engines — particularly early turbojets or engines in which it is not practical or desirable to have an afterburner — water injection may be used to increase engine thrust, particularly at low-altitudes and at takeoff.
A diesel particulate filter (DPF) is a device designed to remove diesel particulate matter or soot from the exhaust gas of a diesel engine.
The Mitsubishi 6B3 engine is a range of all-alloy piston V6 engines developed by Mitsubishi Motors. Currently, only one engine has been developed, a 3.0 L (2,998 cc) V6 first introduced in the North American version of the second generation Mitsubishi Outlander which debuted in October 2006.
Engine efficiency of thermal engines is the relationship between the total energy contained in the fuel, and the amount of energy used to perform useful work. There are two classifications of thermal engines-
Internal combustion and
External combustion engines.
A hydrogen internal combustion engine vehicle (HICEV) is a type of hydrogen vehicle using an internal combustion engine. Hydrogen internal combustion engine vehicles are different from hydrogen fuel cell vehicles. Instead, the hydrogen internal combustion engine is simply a modified version of the traditional gasoline-powered internal combustion engine. The absence of carbon means that no CO2 is produced, which eliminates the main greenhouse gas emission of a conventional petroleum engine.
The Cummins X-series engine is an Inline (Straight)-6 diesel engine produced by Cummins for heavy duty trucks and motorcoaches, replacing the N14 in 2001 when emissions regulations passed by the EPA made the engine obsolete. Originally called the "Signature" series engine, the ISX uses the "Intellect System" to further improve the engine. This engine is widely used in on highway and vocational trucks and is available in power ranging from 430 hp all the way to 620 hp 2050 lb-ft. The QSX is the off-highway version of the ISX with the Q standing for Quantum. The QSX is used for industrial, marine, oil & gas and other off-highway applications. Cummins also produced a 650 hp and 1950 lb-ft version for the RV market.
The SRM Engine Suite is an engineering software tool used for simulating fuels, combustion and exhaust gas emissions in internal combustion engine applications. It is used worldwide by leading IC engine development organisations and fuel companies. The software is developed, maintained and supported by CMCL Innovations, Cambridge, U.K.
Mitsubishi MCA stands for Mitsubishi Clean Air, a moniker used in Japan to identify vehicles built with emission control technology. The term was first introduced in Japan, with later introductions internationally. The technology first appeared in January 1973 on the Mitsubishi 4G32A gasoline-powered inline four cylinder engine installed in all Mitsubishi vehicles using the 4G32 engine, and the Saturn-6 6G34 six-cylinder gasoline-powered engine installed in the Mitsubishi Debonair. The technology was installed so that their vehicles would be in compliance with Japanese Government emission regulations passed in 1968.
An internal combustion engine is a heat engine in which the combustion of a fuel occurs with an oxidizer in a combustion chamber that is an integral part of the working fluid flow circuit. In an internal combustion engine, the expansion of the high-temperature and high-pressure gases produced by combustion applies direct force to some component of the engine. The force is typically applied to pistons, turbine blades, a rotor, or a nozzle. This force moves the component over a distance, transforming chemical energy into kinetic energy which is used to propel, move or power whatever the engine is attached to.
↑ Sileghem & Van De Giste, 2011. Quote: "The results on the Audi-engine indicate that methanol is more EGR tolerant than gasoline, due to its higher flame speed. An EGR tolerance of 27% was found when methanol was used. The efficiencies of the methanol-fueled engine obtained with EGR are higher to those obtained with throttled stoichiometric operation."
1 2 Rosen (Ed.), Erwin M. (1975). The Peterson automotive troubleshooting & repair manual. Grosset & Dunlap, Inc. ISBN978-0-448-11946-5.
↑ Alger, 2010. Quote: "Recent studies performed by engineers at Southwest Research Institute (SwRI) have examined the role that exhaust gas recirculation (EGR) can play in reducing, or even eliminating, these sources of inefficiency in gasoline engines. In internally funded research, they determined that EGR can improve the fuel consumption of both direct-injected and port-injected gasoline engines by reducing pumping losses, mitigating knock, cooling the exhaust and eliminating the need for fuel enrichment."
↑ Dennis A., Garner C., Taylor D. (1999). The Effect of EGR on Diesel Engine Wear, SAE 1999-01-0839, In-Cylinder Diesel Particulate and NOx Control 1999
↑ Nagel, John (2002). Diesel Engine and Fuel System Repair, ISBN0130929816.
↑ Bennett, Sean (2004). Medium/Heavy Duty Truck Engines, Fuel & Computerized Management Systems 2nd Edition, ISBN1401814999.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
