Pistonless pump

Last updated September 28, 2022

A pistonless pump is a type of pump designed to move fluids without any moving parts other than three chamber valves.

Introduction

NASA have developed a low-cost rocket-fuel pump which has comparable performance to a turbopump at 80–90% lower cost.^[1] Perhaps the most difficult barrier to entry in the liquid rocket business is the turbopump. A turbopump design requires a large engineering effort and is expensive to manufacture and test. Starting a turbopump-fed rocket engine is a complex process, requiring a careful synchronisation of many valves and subsystems. In fact, Beal aerospace tried to avoid the issue entirely by building a huge pressure feed booster. Their booster never flew, but the engineering behind it was sound and, if they had a low cost pump at their disposal, they might be competing against Boeing. This pump saves up to 90% of the mass of the tanks as compared to a pressure-fed system. This pump has really proved to be a boon for rockets. By using this pump, the rocket does not have to carry such a heavy load and can travel with very high speed.^[2]

Working cycle

The cycle is as follows:

The fluid enters and fills the chamber from the inlet valve. The outlet and pressurant valves are closed.
The inlet valve closes, the outlet and pressurant valves open. The presurant forces the fluid through the outlet valve.
As the chamber empties, the presurant valve closes and the inlet valve opens, followed by the outlet valve closing.
The cycle is repeated.

Pumping rate

Rocket engines requires a tremendous amount of fuel at high pressure. Often the pump costs more than the thrust chamber. One way to supply fuel is to use the expensive turbopump mentioned above, another way is to pressurize fuel tank. Pressurizing a large fuel tank requires a heavy, expensive tank. However suppose instead of pressurizing the entire tank, the main tank is drained into a small pump chamber which is then pressurized. To achieve steady flow, the pump system consists of two pump chambers such that each one supplies fuel for half of each cycle. The pump is powered by pressurized gas which acts directly on the fluid. For each half of the pump system, a chamber is filled from the main tank under low pressure and at a high flow rate, then the chamber is pressurized, and then the fluid is delivered to the engine at a moderate flow rate under high pressure. The chamber is then vented and cycle repeats. The system is designed so that the inlet flow rate is higher than the outlet flow rate. This allows time for one chamber to be vented, refilled and pressurized while the other is being emptied. A bread board pump has been tested and it works great. A high version has been designed and built and is pumping at 20 gpm and 550 psi.

Application in rocketry

It is most commonly used^{[ citation needed ]} to supply propellants to rocket engines. In this configuration there are often two pumps working in opposite cycles to ensure a constant flow of propellants to the engine.

The pump has the advantage over a pressure-fed system in that the tanks can be much lighter. Compared to a turbopump the pistonless pump is a much simpler design and has less stringent design tolerances.

Advantages

Nearly all of the hardware in this pump consists of pressure vessels, so the weight is low. There are fewer than 10 moving parts, and no lubrication issues which might cause problems with other pumps. The design and construction of this pump is straight forward and no precision parts are required. This device has advantage over standard turbopumps in that the weight is about the same, the unit, engineering and test costs are less and the chance for catastrophic failure is lower. This pump has the advantage over pressure-fed designs in that the weight of the complete rocket is much less, and the rocket is much safer because the tanks of rocket fuel do not need to be at high pressure. The pump could be started after being stored for an extended period with high reliability. It can be used to replace turbopumps for rocket booster option or it can be used to replace high pressure tanks for deep space propulsion. It can also be used for satellite orbit changes and station keeping.

Disadvantages

The pistonless pumps also has some disadvantages, such as:

They cannot pump to higher pressure than drive gas (area ratio is 1:1).
They cannot use either a staged combustion or expander cycle.
A gas generator cycle is also difficult to integrate with the pistonless pump.
The generated gas must be chemically compatible with both the propellants.
This gas generator lowers the Ignition start period of the engine.

Related Research Articles

A turbopump is a propellant pump with two main components: a rotodynamic pump and a driving gas turbine, usually both mounted on the same shaft, or sometimes geared together. They were initially developed in Germany in the early 1940s. The purpose of a turbopump is to produce a high-pressure fluid for feeding a combustion chamber or other use.

A hybrid-propellant rocket is a rocket with a rocket motor that uses rocket propellants in two different phases: one solid and the other either gas or liquid. The hybrid rocket concept can be traced back to the early 1930s.

A rocket engine uses stored rocket propellants as the reaction mass for forming a high-speed propulsive jet of fluid, usually high-temperature gas. Rocket engines are reaction engines, producing thrust by ejecting mass rearward, in accordance with Newton's third law. Most rocket engines use the combustion of reactive chemicals to supply the necessary energy, but non-combusting forms such as cold gas thrusters and nuclear thermal rockets also exist. Vehicles propelled by rocket engines are commonly called rockets. Rocket vehicles carry their own oxidiser, unlike most combustion engines, so rocket engines can be used in a vacuum to propel spacecraft and ballistic missiles.

The expander cycle is a power cycle of a bipropellant rocket engine. In this cycle, the fuel is used to cool the engine's combustion chamber, picking up heat and changing phase. The now heated and gaseous fuel then powers the turbine that drives the engine's fuel and oxidizer pumps before being injected into the combustion chamber and burned.

RP-1 (alternatively, Rocket Propellant-1 or Refined Petroleum-1) is a highly refined form of kerosene outwardly similar to jet fuel, used as rocket fuel. RP-1 provides a lower specific impulse than liquid hydrogen (LH₂), but is cheaper, is stable at room temperature, and presents a lower explosion hazard. RP-1 is far denser than LH₂, giving it a higher energy density (though its specific energy is lower). RP-1 also has a fraction of the toxicity and carcinogenic hazards of hydrazine, another room-temperature liquid fuel.

A liquid-propellant rocket or liquid rocket utilizes a rocket engine that uses liquid propellants. Liquids are desirable because they have a reasonably high density and high specific impulse (I_sp). This allows the volume of the propellant tanks to be relatively low. It is also possible to use lightweight centrifugal turbopumps to pump the rocket propellant from the tanks into the combustion chamber, which means that the propellants can be kept under low pressure. This permits the use of low-mass propellant tanks that do not need to resist the high pressures needed to store significant amounts of gasses, resulting in a low mass ratio for the rocket.

The Aerojet Rocketdyne RS-25, also known as the Space Shuttle Main Engine (SSME), is a liquid-fuel cryogenic rocket engine that was used on NASA's Space Shuttle and is currently used on the Space Launch System (SLS).

The J-2 is a liquid-fuel cryogenic rocket engine used on NASA's Saturn IB and Saturn V launch vehicles. Built in the U.S. by Rocketdyne, the J-2 burned cryogenic liquid hydrogen (LH2) and liquid oxygen (LOX) propellants, with each engine producing 1,033.1 kN (232,250 lb_f) of thrust in vacuum. The engine's preliminary design dates back to recommendations of the 1959 Silverstein Committee. Rocketdyne won approval to develop the J-2 in June 1960 and the first flight, AS-201, occurred on 26 February 1966. The J-2 underwent several minor upgrades over its operational history to improve the engine's performance, with two major upgrade programs, the de Laval nozzle-type J-2S and aerospike-type J-2T, which were cancelled after the conclusion of the Apollo program.

The Rocketdyne H-1 is a 205,000 lbf (910 kN) thrust liquid-propellant rocket engine burning LOX and RP-1. The H-1 was developed for use in the S-I and S-IB first stages of the Saturn I and Saturn IB rockets, respectively, where it was used in clusters of eight engines. After the Apollo program, surplus H-1 engines were rebranded and reworked as the Rocketdyne RS-27 engine with first usage on the Delta 2000 series in 1974. The RS-27 variant is also used on the Delta II and Delta III.

The staged combustion cycle is a power cycle of a bipropellant rocket engine. In the staged combustion cycle, propellant flows through multiple combustion chambers, and is thus combusted in stages. The main advantage relative to other rocket engine power cycles is high fuel efficiency, measured through specific impulse, while its main disadvantage is engineering complexity.

The pressure-fed engine is a class of rocket engine designs. A separate gas supply, usually helium, pressurizes the propellant tanks to force fuel and oxidizer to the combustion chamber. To maintain adequate flow, the tank pressures must exceed the combustion chamber pressure.

<span class="mw-page-title-main">Aerojet M-1</span> Largest rocket engine to be designed

The Aerojet M-1 was the largest and most powerful liquid-hydrogen-fueled liquid-fuel rocket engine to be designed and component-tested. It was originally developed during the 1950s by the US Air Force. The M-1 offered a baseline thrust of 6.67 MN and an immediate growth target of 8 MN. If built, the M-1 would have been larger and more efficient than the famed F-1 that powered the first stage of the Saturn V rocket to the Moon.

The YF-75 is a liquid cryogenic rocket engine burning liquid hydrogen and liquid oxygen in a gas generator cycle. It is China's second generation of cryogenic propellant engine, after the YF-73, which it replaced. It is used in a dual engine mount in the H-18 third stage of the Long March 3A, Long March 3B and Long March 3C launch vehicles. Within the mount, each engine can gimbal individually to enable thrust vectoring control. The engine also heats hydrogen and helium to pressurize the stage tanks and can control the mixture ratio to optimize propellant consumption.

The YF-77 is China's first cryogenic rocket engine developed for booster applications. It burns liquid hydrogen fuel and liquid oxygen oxidizer using a gas generator cycle. A pair of these engines powers the LM-5 core stage. Each engine can independently gimbal in two planes. Although the YF-77 is ignited prior to liftoff, the LM-5's four strap-on boosters provide most of the initial thrust in an arrangement similar to the European Vulcain on the Ariane 5 or the Japanese LE-7 on the H-II.

This article briefly describes the components and systems found in jet engines.

<span class="mw-page-title-main">Cryogenic rocket engine</span> Type of rocket engine which uses liquid fuel stored at very low temperatures

A cryogenic rocket engine is a rocket engine that uses a cryogenic fuel and oxidizer; that is, both its fuel and oxidizer are gases which have been liquefied and are stored at very low temperatures. These highly efficient engines were first flown on the US Atlas-Centaur and were one of the main factors of NASA's success in reaching the Moon by the Saturn V rocket.

Fastrac was a turbo pump-fed, liquid rocket engine. The engine was designed by NASA as part of the low cost X-34 Reusable Launch Vehicle (RLV) and as part of the Low Cost Booster Technology project. This engine was later known as the MC-1 engine when it was merged into the X-34 project.

TM65 is a rocket engine developed by Copenhagen Suborbitals. TM65 uses Ethanol and liquid oxygen as propellants in a pressure-fed power cycle.

<span class="mw-page-title-main">XLR81</span>

The Bell Aerosystems Company XLR81 was an American liquid-propellant rocket engine, which was used on the Agena upper stage. It burned UDMH and RFNA fed by a turbopump in a fuel rich gas generator cycle. The turbopump had a single turbine with a gearbox to transmit power to the oxidizer and fuel pumps. The thrust chamber was all-aluminum, and regeneratively cooled by oxidizer flowing through gun-drilled passages in the combustion chamber and throat walls. The nozzle was a titanium radiatively cooled extension. The engine was mounted on a hydraulic actuated gimbal which enabled thrust vectoring to control pitch and yaw. Engine thrust and mixture ratio were controlled by cavitating flow venturis on the gas generator flow circuit. Engine start was achieved by solid propellant start cartridge.

Autogenous pressurization is the use of self-generated gaseous propellant to pressurize liquid propellant in rockets. Traditional liquid-propellant rockets have been most often pressurized with other gases, such as helium, which necessitates carrying the pressurant tanks along with the plumbing and control system to use it. Autogenous pressurization has been operationally used on the Titan 34D and the Space Shuttle. Autogenous pressurization is planned to be used on the SLS, Starship, New Glenn, Terran 1, ACES upper-stage and Rocket Lab's Neutron rocket.

References

↑ "Successful NASA Rocket Fuel Pump Tests Pave Way for 3-D Printed Demonstrator Engine". nasa.gov. 27 August 2015. Retrieved 3 April 2020.
↑ Starkey, Ryan (2014). "Development of a Pistonless Rocket Engine Pump Suborbital Flight Test Demonstrator". ResearchGate. doi:10.2514/6.2014-3784.