signals, views to, turntable, railway, clock, signal box/signal cabin/switch house/mechanical points (rail), signal mast, machinery/plant/equipment – transport – rail, views from
Location of Railway Signal Cabin and Turntable in Queensland
Show map of Queensland
Railway Signal Cabin and Turntable, Ipswich (Australia)
The three-storey timber signal cabin at Ipswich containing an 1881 McKenzie and Holland mechanical interlocking signal frame and the nearby locomotive turntable and semaphore signal were once important components of the Ipswich railway station infrastructure.[1]
The first railway in Queensland started from Ipswich, a provincial centre, rather than the capital Brisbane, because it was thought that river transport adequately linked Brisbane and Ipswich and that the major need was to improve transport between Ipswich and the productive Darling Downs agricultural region. Work started in early 1864 and the first section of line, from Ipswich to Grandchester, was opened in 1865, gradually extending to the Darling Downs and eventually further west. Ipswich and Brisbane were linked by rail in 1875.[1]
Although the Ipswich railway workshops were at North Ipswich, the railway station was in the centre of the town, on the southern side of the Bremer River. The line from the station passed over a combined rail/road bridge across the river. It then passed through the workshops, continued beside the river, crossed Mihi Creek and on to Grandchester and the Darling Downs.[1]
There have been three railway stations at Ipswich, all situated close to the same site. The first was immediately south of the Bremer River Bridge and opened on 31 July 1865. When the extension from Ipswich to Sherwood in Brisbane opened on 5 October 1874, space did not allow a direct connection and the trains had to reverse. Trains from Brisbane had to pass the junction then reversed in, while those from Toowoomba could run straight into the station but had to reverse out before continuing to Brisbane. When the Ipswich deviation was opened on 26 April 1875 it provided a direct line through Ipswich.[1]
Where more than one train uses a railway line it is important to avoid train movements that may result in a collision. Early methods to prevent this included a Staff and Ticket relay system where a physical token was carried on the train and was passed to the next train travelling in the opposite direction before it could proceed. An Electric Staff functioning as part of an electronic system was introduced later, but operated on much the same principle. With the ongoing growth of the rail network, and where train movements have become more frequent and complex, the further evolution of safeworking has seen the development of Centralised Train Control (CTC). This is a system where the signals and points controlling movement are operated from a remote computer location. Within Queensland Rail other forms of train control are now replacing or augmenting this system also.[1]
An interlocked yard is a railway yard where semaphore or coloured light signals are controlled in such a way that signals cannot be set to proceed unless the points that operate in conjunction with the signals are correctly set. A mechanical interlocking device is a system of rods, sliding bars and levers that are configured so that points cannot be changed in conflict, thus preventing movements that may cause a collision or other accident.[1]
The earliest designs used various ingenious and patented methods to interlock the levers. Stevens & Sons invented a tappet system that later became almost universal but didn't renew their patent so that this system was adopted by many other manufacturers.[1]
McKenzie and Holland (originally McKenzie, Clunes & Holland) were one of the earliest signalling contractors in Britain and supplied many railway companies, though few of these mechanisms now survive. In 1873 they introduced a new design of lever frame that would set the style of all frames to come. A dogleg on the shape of the levers allowed them to stand upright in the frame when in the normal position, which made them easier for a signalman to use. The locking mechanism was known as cam and soldier rotary locking and remained in use for many years, although later models refined the design.[1]
At the Sydney International Exhibition in Sydney in 1880, Arthur Orpen Herbert, the Commissioner for Queensland Railway, was impressed by a display of McKenzie and Holland interlocking machines. The New South Wales Government bought the equipment on display, using it for the first installation in Australia. Queensland ordered the same equipment for Roma Street and Ipswich stations and this arrived in October 1881. Although the interlocking mechanism was a major factor in ensuring safety at busy stations, traffic on much of Queensland's railway lines was insufficient to warrant the installation of the expensive machinery required and most lines obtained safeworking by staff and ticket or a similar system. The fact that the only mechanism installed in Queensland outside Brisbane was at Ipswich suggests a high level of traffic at Ipswich and its importance as a railway centre.[1]
At Ipswich, a contract was immediately let for a signal cabin and the interlocking was completed in late 1883. The design of this first cabin is unknown, but signal cabins in Australia have followed precedents that proved successful overseas and the current signal box generally resembles elevated cabins built by McKenzie and Holland in Britain. On 12 August 1895 a contract was let to W. Chaplain to build a new signal cabin and this is the cabin now in place. It controlled train movements between Thomas Street and East Ipswich railway stations and to the Railway Workshops across the river. The cabin is unusual in being three, rather than two storeys high, its location making this necessary, so that the signalman could see over the top of the bridge and also the main line to the west.[1]
A contract to build a new station on the through line, in a cutting, was let to Henry Wyman on 9 March 1886. This opened on 17 October 1887. This station had one through platform with dock platforms at either end. Extensive alterations were planned and began in 1914. It was intended to include a new station building west of the original station on the through alignment between West and Waghorn Streets, though this was not built. Work completed included a subway in line with West Street, a new platform and the foundations for the proposed station. A new 60-foot (18m) turntable was installed as part of these alterations in 1921, replacing a 41-foot (12m) turntable that was too short to accommodate the new locomotives. Electropneumatic signalling and interlocking was to be installed, but was installed at Gympie instead, so that Ipswich retained its mechanical interlocking system. A third railway station was eventually built in 1974.[1]
The other major feature remaining from the railway infrastructure is a locomotive turntable. Ipswich station was unusual for a major station in having only a single line, as the double track main line between Brisbane and Toowoomba was slewed to pass through the station, which only had one through platform face, other platforms being dead ends. A turntable provides for the rotation of locomotives, being a section of line mounted on a rotating platform with the operating mechanism beneath. As part of the station yard alterations in 1921, a new 60-foot (18m) turntable was provided near the elevated signal cabin, replacing the old 41-foot (12m) turntable that was too short for modern steam locomotives. An English Cowan Sheldon and Co Ltd no 10297 motor that was installed in 1957 operates it.[1]
Diesel electric locomotives replaced steam locomotives on Queensland railways during the 1960s, with Ipswich being the last fully dedicated steam locomotive depot in southern Queensland. They could travel in either direction without turning so that turntables became unnecessary and many turntables and fork lines have been removed, so that they are now uncommon. The turntable at Ipswich was in use for both steam and diesel a locomotive when many locomotive hauled trains terminated there. The turntable is still a part of QR operations and is still used for turning steam locomotives.[1]
Although Ipswich was only the second station in Queensland to have mechanical interlocking installed, it was retained long after its withdrawal from Roma Street. The technology became obsolete, as electrical interlocking or electro-pneumatic systems replaced mechanical interlocking. Computerised Centralised Traffic Control signalling systems that allow control of trains, generally from a single dedicated location up to several hundred kilometres away, now control most of the network.[1]
The section of railway yard containing the signal cabin and turntable has been isolated from the railway station by the development of a large modern shopping centre. The signal cabin was de-commissioned in 1995.[1]
Positioned on the former main line leading to the Ipswich Railway Workshops is a semaphore signal and mast to the north of the signal cabin, which is now a rare surviving example in Queensland on the main line.[1]
Description
The elevated timber signal cabin and adjacent turntable are situated close together to the east of the bridge across the Bremer River and are faced on three sides by the exterior walls of a large shopping centre.[1]
The elevated signal cabin is a rectangular timber structure three storeys high. It has a gabled roof clad in corrugated iron sheeting with a timber finial at each end. The cabin houses a 55-lever T-bar interlocking machine by MacKenzie and Holland. The top level houses the signal levers and good visibility is provided for the signalman by banks of windows to each side. The machinery to which the levers are connected is below and single windows light the two lower levels.[1]
An external staircase on the north side gives access to a door on the second level and leads to a narrow landing on the top floor, which is shaded by a roof. The structure contains a pericope for signalmen to obtain a view under the adjoining vehicular bridges over the rail corridor. There is a Synchrome Electric clock on the northern elevation. There is also a semaphore signal mast to the north of the signal cabin.[1]
The turntable is situated to the north east of the signal cabin. It is a standard 60-foot (18m) table with pneumatic motor, originally powered by the Westinghouse air brake pump and system on the steam locomotive.[1]
Heritage listing
Railway Signal Cabin and Turntable was listed on the Queensland Heritage Register on 27 May 2005 having satisfied the following criteria.[1]
The place is important in demonstrating the evolution or pattern of Queensland's history.
The Railway Signal Cabin with its mechanically interlocked signalling system and Turntable for positioning and turning steam locomotives are evidence of the development of rail transport in Queensland. As the earliest such interlocking system outside the capital, it demonstrates the importance of Ipswich as a railway centre when the establishment of a railway network was seen as the key to encouraging wider settlement in Queensland and providing reliable transport for people, goods and raw materials between the coastal cities and the productive interior regions.[1]
The place demonstrates rare, uncommon or endangered aspects of Queensland's cultural heritage.
The McKenzie and Holland mechanism for controlling signals, and consequently train movements, was installed in 1883 as one of only two in Queensland, the other being at Roma Street in Brisbane and which has not survived. It is now rare in Australia, as very few signal boxes survive with mechanical interlocking systems in place, particularly of such an early date.[1]
The place is important in demonstrating the principal characteristics of a particular class of cultural places.
The elevated signal cabin is the largest and best surviving example of its type, which is now rare in Queensland, as is the turntable and the semaphore signal. The signal frame is the second largest ever used in Queensland.[1]
The place is important in demonstrating a high degree of creative or technical achievement at a particular period.
The interlocking system, semaphore signal and the locomotive turntable are good examples of an obsolete technology that was vital to the safe operation of the railway and were technically sophisticated at the time of their commissioning. The signal cabin demonstrates the characteristics of its type well, being elevated and positioned to provide commanding sightlines for the signalman. The top level has banks of windows to provide a good view and lighting. This level houses the lever frame and the level below contains the mechanism. The turntable is a good example of its type, being operational and recently serviced, and in its original location.[1]
The McKenzie and Holland interlocking frame represents the most advanced technology available in its field at the time of its manufacture and made a major contribution to the safety of rail travel.[1]
Related Research Articles
The South Tynedale Railway is a preserved, 2 ft narrow gauge heritage railway in Northern England and at 875ft is England's second highest narrow gauge railway after the Lynton and Barnstaple Railway in north Devon. The South Tynedale line runs from Alston in Cumbria, down the South Tyne Valley, via Gilderdale, Kirkhaugh and Lintley, then across the South Tyne, Gilderdale and Whitley Viaducts to Slaggyford in Northumberland.
A railway signal is a visual display device that conveys instructions or provides warning of instructions regarding the driver’s authority to proceed. The driver interprets the signal's indication and acts accordingly. Typically, a signal might inform the driver of the speed at which the train may safely proceed or it may instruct the driver to stop.
On a rail transport system, signalling control is the process by which control is exercised over train movements by way of railway signals and block systems to ensure that trains operate safely, over the correct route and to the proper timetable. Signalling control was originally exercised via a decentralised network of control points that were known by a variety of names including signal box, interlocking tower and signal cabin. Currently these decentralised systems are being consolidated into wide scale signalling centres or dispatch offices. Whatever the form, signalling control provides an interface between the human signal operator and the lineside signalling equipment. The technical apparatus used to control switches (points), signals and block systems is called interlocking.
The Watercress Line is the marketing name of the Mid-Hants Railway, a heritage railway in Hampshire, England, running 10 miles (16 km) from New Alresford to Alton where it connects to the National Rail network. The line gained its popular name in the days when it was used to transport locally grown watercress to markets in London. The railway currently operates regular scheduled services, along with dining trains, real ale trains and numerous special events throughout the year.
In railway signalling, an interlocking is an arrangement of signal apparatus that prevents conflicting movements through an arrangement of tracks such as junctions or crossings. In North America, a set of signalling appliances and tracks interlocked together are sometimes collectively referred to as an interlocking plant or just as an interlocking. An interlocking system is designed so that it is impossible to display a signal to proceed unless the route to be used is proven safe.
Automatic Warning System (AWS) is a railway safety system used in railways around the world. It provides a train driver with an audible indication of whether the next signal they are approaching is clear or at caution. Depending on the upcoming signal state, the AWS will either produce a 'horn' sound, or a 'bell' sound. If the train driver fails to acknowledge a warning indication, an emergency brake application is initiated by the AWS. However if the driver correctly acknowledges the warning indication by pressing an acknowledgement button, then a visual 'sunflower' is displayed to the driver, as a reminder of the warning.
Archer Park Railway Museum is a heritage-listed former railway station and now transport museum at Denison Street, Rockhampton, Rockhampton Region, Queensland, Australia. It was built from 1897 to 1908. It was known as Archer Park railway station and Rockhampton Central railway station. It was added to the Queensland Heritage Register on 21 October 1992.
The Connington South rail crash occurred on 5 March 1967 on the East Coast Main Line near the village of Conington, Huntingdonshire, England. Five passengers were killed and 18 were injured.
Mechanical railway signalling installations rely on lever frames for their operation to interlock the signals, track locks and points to allow the safe operation of trains in the area the signals control. Usually located in the signal box, the levers are operated either by the signalman or the pointsman.
The Swanley New Barn Railway is a 7+1⁄4 in gauge railway located in Swanley Park, Swanley, Kent, United Kingdom. It is signalled throughout with the signals being controlled from New Barn Station which also serves as a terminus.
A signalman or signaller is an employee of a railway transport network who operates the points and signals from a signal box in order to control the movement of trains.
Summit railway station was at the summit of the Wairarapa Line over the Rimutaka Ranges in the Wellington region of New Zealand’s North Island and was where trains were marshalled for a descent down the Rimutaka Incline or for Fell locomotives to be extricated from a train that had ascended the Incline. The station was between Kaitoke and Cross Creek stations on the Wairarapa Line. The station was bypassed when the Rimutaka Tunnel was opened.
Cross Creek railway station was the base of operations for the Rimutaka Incline, a Fell railway over the Remutaka Ranges, and part of the original Wairarapa Line between Upper Hutt and Featherston in the Wellington region of New Zealand's North Island. The station was between Pigeon Bush and Summit stations on the Wairarapa Line. The station was bypassed when the Rimutaka Tunnel was opened.
The Bennett Brook Railway is a 2 ft narrow gauge tourist oriented railway operated by the West Australian Light Railway Preservation Association and is located within the boundaries of Whiteman Park, 19 kilometres (12 mi) from Perth.
Ledbury Signal Box is a typical Great Western Railway traditional lever frame signal box which remains in daily use at Ledbury Station, Herefordshire, England on the railway line from Worcester to Hereford.
Toowoomba railway station is a heritage-listed railway station on the Western line at Russell Street, Toowoomba, Toowoomba Region, Queensland, Australia. It serves the city of Toowoomba, which is the junction for the Western, Main and Southern lines. The station has one platform with a passing loop, opening in 1867. It was designed by FDG Stanley and built in 1873 by R. Godsall. It was added to the Queensland Heritage Register on 21 October 1992.
Murphys Creek Railway Complex is a heritage-listed railway yard on the Main Line railway at Odin Street, Murphys Creek, Queensland, Australia. It was built from 1921 to c. 1949. It is also known as Murphys Creek Locomotive Water Tank & Tower. It was added to the Queensland Heritage Register on 24 September 1999.
Bremer River Rail Bridge is a heritage-listed railway bridge at off Bremer Street, North Ipswich, City of Ipswich, Queensland, Australia. It was built from 1865 to 1915. It was added to the Queensland Heritage Register on 11 December 2006.
The Cairns-to-Kuranda Railway is a heritage-listed railway line from the Cairns Region to the Shire of Mareeba, both in Queensland, Australia. It commences at Redlynch, a suburb of Cairns and travels up the Great Dividing Range to Kuranda within the Shire of Mareeba on the Atherton Tableland. It was built from 1913 to 1915 by Queensland Railways. Components of it include Stoney Creek Bridge, the Rail Bridge over Christmas Creek, Kuranda railway station, and Surprise Creek Rail Bridge. It was added to the Queensland Heritage Register on 21 August 1992. The railway is used to operate a tourist rail service, the Kuranda Scenic Railway. It forms part of the Tablelands railway line.
The Signals, Crane and Subway are heritage-listed railway infrastructure at Charters Towers railway station, Enterprise Road, Charters Towers, Charters Towers Region, Queensland, Australia. They were added to the Queensland Heritage Register on 30 October 2008.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
