Richmann's law

Last updated

Richmann's law, [1] [2] sometimes referred to as Richmann's rule, [3] Richmann's mixing rule, [4] Richmann's rule of mixture [5] or Richmann's law of mixture, [6] is a physical law for calculating the mixing temperature when pooling multiple bodies. [5] It is named after the Baltic German physicist Georg Wilhelm Richmann, who published the relationship in 1750, establishing the first general equation for calorimetric calculations. [7] [8]

Contents

Origin

Through experimental measurements, Wilhelm Richmann determined that the following relationship holds when water of different temperatures is mixed: [9]

It follows:

Initial Richman's law
(Eq.1)

Here and are the masses of the two mixture components, and are their respective initial temperatures, and is the mixture temperature.

This observation is called Richmann's law in the narrower sense and applies in principle to all substances of the same state of aggregation. [1] [9] According to this, the mixing temperature is the weighted arithmetic mean of the temperatures of the two initial components.

Richmann's rule of mixing can also be applied in reverse, for example, to the question of the ratio in which quantities of water of given temperatures must be mixed to obtain water of a desired temperature. Determining the quantities and required for this purpose, given a total quantity , is accomplished with the mixing cross. The corresponding formula, obtained from the above equation by rearrangement, is:

or .

For the mixing ratio, this gives:

.

The physical background of the mixing rule is the fact that the heat energy of a substance is directly proportional to its mass and its absolute temperature. The proportionality factor is the specific heat capacity, which depends on the nature of the substance, but which was not described until some time after Richmann's discovery by Joseph Black. Thus, the validity of the formula is limited to mixtures of the same substance, since it assumes a uniform specific heat capacity. [9] Another condition is that both components be uniformly warm everywhere and that there be no appreciable heat exchange with their other surroundings.

If one wants to mix two substances with different - but known - specific heat capacities, one can formulate the mixing rule more generally, as shown below.

General formulation

Under the condition that no change of aggregate state occurs and the system is closed, i.e., in particular, there is no heat exchange with the environment, the following holds:

Where and represent the specific enthalpy of the respective components.

If the specific heat capacities and can be assumed to be constant, this can be transformed to.

The formula resolved by the mixture temperature is then:

General Richman's law
(Eq.2)

In a wider sense this equation is also referred to as Richmann's law because it simply extends Richmann's established relationship to include the specific heat capacity, thus allowing the calculation of the mixing temperature of different substances. [2] [5] [10]

If the heat capacities are not constant over the entire temperature range, the above formula can be used with an average heat capacity for component :

.

In this formula, with or represents the specific heat capacity of the two components, which may be temperature dependent. Application of the formula may require an iterative procedure to determine the mixture temperature, since the average heat capacity is also temperature dependent.

Related Research Articles

<span class="mw-page-title-main">Enthalpy</span> Measure of energy in a thermodynamic system

Enthalpy is the sum of a thermodynamic system's internal energy and the product of its pressure and volume. It is a state function in thermodynamics used in many measurements in chemical, biological, and physical systems at a constant external pressure, which is conveniently provided by the large ambient atmosphere. The pressure–volume term expresses the work that was done against constant external pressure to establish the system's physical dimensions from to some final volume , i.e. to make room for it by displacing its surroundings. The pressure-volume term is very small for solids and liquids at common conditions, and fairly small for gases. Therefore, enthalpy is a stand-in for energy in chemical systems; bond, lattice, solvation, and other chemical "energies" are actually enthalpy differences. As a state function, enthalpy depends only on the final configuration of internal energy, pressure, and volume, not on the path taken to achieve it.

<span class="mw-page-title-main">Specific heat capacity</span> Heat required to increase temperature of a given unit of mass of a substance

In thermodynamics, the specific heat capacity of a substance is the amount of heat that must be added to one unit of mass of the substance in order to cause an increase of one unit in temperature. It is also referred to as massic heat capacity or as the specific heat. More formally it is the heat capacity of a sample of the substance divided by the mass of the sample. The SI unit of specific heat capacity is joule per kelvin per kilogram, J⋅kg−1⋅K−1. For example, the heat required to raise the temperature of 1 kg of water by 1 K is 4184 joules, so the specific heat capacity of water is 4184 J⋅kg−1⋅K−1.

<span class="mw-page-title-main">Partial pressure</span> Pressure of a component gas in a mixture

In a mixture of gases, each constituent gas has a partial pressure which is the notional pressure of that constituent gas as if it alone occupied the entire volume of the original mixture at the same temperature. The total pressure of an ideal gas mixture is the sum of the partial pressures of the gases in the mixture.

<span class="mw-page-title-main">Stefan–Boltzmann law</span> Physical law on the emissive power of black body

The Stefan–Boltzmann law, also known as Stefan's law, describes the intensity of the thermal radiation emitted by matter in terms of that matter's temperature. It is named for Josef Stefan, who empirically derived the relationship, and Ludwig Boltzmann who derived the law theoretically.

<span class="mw-page-title-main">Gas constant</span> Physical constant equivalent to the Boltzmann constant, but in different units

The molar gas constant is denoted by the symbol R or R. It is the molar equivalent to the Boltzmann constant, expressed in units of energy per temperature increment per amount of substance, rather than energy per temperature increment per particle. The constant is also a combination of the constants from Boyle's law, Charles's law, Avogadro's law, and Gay-Lussac's law. It is a physical constant that is featured in many fundamental equations in the physical sciences, such as the ideal gas law, the Arrhenius equation, and the Nernst equation.

<span class="mw-page-title-main">Speed of sound</span> Speed of sound wave through elastic medium

The speed of sound is the distance travelled per unit of time by a sound wave as it propagates through an elastic medium. More simply, the speed of sound is how fast vibrations travel. At 20 °C (68 °F), the speed of sound in air is about 343 m/s, or 1 km in 2.91 s or one mile in 4.69 s. It depends strongly on temperature as well as the medium through which a sound wave is propagating. At 0 °C (32 °F), the speed of sound in air is about 331 m/s.

<span class="mw-page-title-main">Planck's law</span> Spectral density of light emitted by a black body

In physics, Planck's law describes the spectral density of electromagnetic radiation emitted by a black body in thermal equilibrium at a given temperature T, when there is no net flow of matter or energy between the body and its environment.

<span class="mw-page-title-main">Gibbs free energy</span> Type of thermodynamic potential

In thermodynamics, the Gibbs free energy is a thermodynamic potential that can be used to calculate the maximum amount of work, other than pressure-volume work, that may be performed by a thermodynamically closed system at constant temperature and pressure. It also provides a necessary condition for processes such as chemical reactions that may occur under these conditions. The Gibbs free energy is expressed asWhere:

<span class="mw-page-title-main">Isobaric process</span> Thermodynamic process in which pressure remains constant

In thermodynamics, an isobaric process is a type of thermodynamic process in which the pressure of the system stays constant: ΔP = 0. The heat transferred to the system does work, but also changes the internal energy (U) of the system. This article uses the physics sign convention for work, where positive work is work done by the system. Using this convention, by the first law of thermodynamics,

<span class="mw-page-title-main">Equipartition theorem</span> Theorem in classical statistical mechanics

In classical statistical mechanics, the equipartition theorem relates the temperature of a system to its average energies. The equipartition theorem is also known as the law of equipartition, equipartition of energy, or simply equipartition. The original idea of equipartition was that, in thermal equilibrium, energy is shared equally among all of its various forms; for example, the average kinetic energy per degree of freedom in translational motion of a molecule should equal that in rotational motion.

In chemical thermodynamics, the fugacity of a real gas is an effective partial pressure which replaces the mechanical partial pressure in an accurate computation of chemical equilibrium. It is equal to the pressure of an ideal gas which has the same temperature and molar Gibbs free energy as the real gas.

In thermodynamics, the heat transfer coefficient or film coefficient, or film effectiveness, is the proportionality constant between the heat flux and the thermodynamic driving force for the flow of heat. It is used in calculating the heat transfer, typically by convection or phase transition between a fluid and a solid. The heat transfer coefficient has SI units in watts per square meter per kelvin (W/m2K).

The Clausius–Clapeyron relation, in chemical thermodynamics, specifies the temperature dependence of pressure, most importantly vapor pressure, at a discontinuous phase transition between two phases of matter of a single constituent. It is named after Rudolf Clausius and Benoît Paul Émile Clapeyron. However, this relation was in fact originally derived by Sadi Carnot in his Reflections on the Motive Power of Fire, which was published in 1824 but largely ignored until it was rediscovered by Clausius, Clapeyron, and Lord Kelvin decades later. Kelvin said of Carnot's argument that "nothing in the whole range of Natural Philosophy is more remarkable than the establishment of general laws by such a process of reasoning."

In classical thermodynamics, entropy is a property of a thermodynamic system that expresses the direction or outcome of spontaneous changes in the system. The term was introduced by Rudolf Clausius in the mid-19th century to explain the relationship of the internal energy that is available or unavailable for transformations in form of heat and work. Entropy predicts that certain processes are irreversible or impossible, despite not violating the conservation of energy. The definition of entropy is central to the establishment of the second law of thermodynamics, which states that the entropy of isolated systems cannot decrease with time, as they always tend to arrive at a state of thermodynamic equilibrium, where the entropy is highest. Entropy is therefore also considered to be a measure of disorder in the system.

The number of transfer units (NTU) method is used to calculate the rate of heat transfer in heat exchangers when there is insufficient information to calculate the log mean temperature difference (LMTD). Alternatively, this method is useful for determining the expected heat exchanger effectiveness from the known geometry. In heat exchanger analysis, if the fluid inlet and outlet temperatures are specified or can be determined by simple energy balance, the LMTD method can be used; but when these temperatures are not available either the NTU or the effectiveness NTU method is used.

In thermodynamics, a partial molar property is a quantity which describes the variation of an extensive property of a solution or mixture with changes in the molar composition of the mixture at constant temperature and pressure. It is the partial derivative of the extensive property with respect to the amount of the component of interest. Every extensive property of a mixture has a corresponding partial molar property.

<span class="mw-page-title-main">Volume (thermodynamics)</span> Extensive parameter used to describe a thermodynamic systems state

In thermodynamics, the volume of a system is an important extensive parameter for describing its thermodynamic state. The specific volume, an intensive property, is the system's volume per unit mass. Volume is a function of state and is interdependent with other thermodynamic properties such as pressure and temperature. For example, volume is related to the pressure and temperature of an ideal gas by the ideal gas law. The physical region covered by a system may or may not coincide with a control volume used to analyze the system.

In physical chemistry, there are numerous quantities associated with chemical compounds and reactions; notably in terms of amounts of substance, activity or concentration of a substance, and the rate of reaction. This article uses SI units.

<span class="mw-page-title-main">Entropy production</span> Development of entropy in a thermodynamic system

Entropy production is the amount of entropy which is produced during heat process to evaluate the efficiency of the process.

Heat transfer physics describes the kinetics of energy storage, transport, and energy transformation by principal energy carriers: phonons, electrons, fluid particles, and photons. Heat is thermal energy stored in temperature-dependent motion of particles including electrons, atomic nuclei, individual atoms, and molecules. Heat is transferred to and from matter by the principal energy carriers. The state of energy stored within matter, or transported by the carriers, is described by a combination of classical and quantum statistical mechanics. The energy is different made (converted) among various carriers. The heat transfer processes are governed by the rates at which various related physical phenomena occur, such as the rate of particle collisions in classical mechanics. These various states and kinetics determine the heat transfer, i.e., the net rate of energy storage or transport. Governing these process from the atomic level to macroscale are the laws of thermodynamics, including conservation of energy.

References

  1. 1 2 Heilbron, J. L. (2022). Elements of Early Modern Physics. [S.l.]: Univ of California Press. pp. 76–79. ISBN   978-0-520-30255-6. OCLC   1301900632.
  2. 1 2 "Final temperature of mixtures (Richmann's law)". tec-science. 2021-01-20. Retrieved 2022-10-31.
  3. Magie, William Francis (1905). Syllabus of a Course of Lectures on Physics. Princeton Press. pp. 149–152. OCLC   17986029.
  4. Verst, Lisa-Marie; Winkler, Gertrud; Lachenmeier, Dirk W. (2018-04-15). "Dispensing and serving temperatures of coffee-based hot beverages Exploratory survey as a basis for cancer risk assessment". Ernährungs Umschau. 65 (4): 65–66. doi:10.4455/eu.2018.014. ISSN   0174-0008.
  5. 1 2 3 Tillmann, Sebastian-T.; Bohn, Christian-A. (2015). "Simulation of Water Condensation based on a Thermodynamic Approach". In D. Bommes; T. Ritschel; T. Schultz (eds.). Vision, Modeling, and Visualization. The Eurographics Association. p. 128. doi:10.2312/VMV.20151267. ISBN   978-3-905674-95-8.
  6. Weiser, Ingo Felix; Mannens, Robby; Feuerhack, Andreas; Trauth, Daniel; Bergs, Thomas (2019). "An analytical approach for the determination of the temperature distribution in the cross section of a sheet metal caused by inductive heating". Procedia Manufacturing. 29: 358. doi: 10.1016/j.promfg.2019.02.148 . S2CID   140378514.
  7. Richmann, Willhelm (1750). Novi commentarii Academiae Scientiarum Imperialis Petropolitanae (in Latin).
  8. "Georg Wilhelm Richmann in Physik". Lernhelfer (Duden) (in German). Retrieved 2022-10-31.
  9. 1 2 3 Fraunberger, Fritz (1984). Das Experiment in der Physik : Ausgewählte Beispiele aus der Geschichte. Jürgen Teichmann. Wiesbaden. p. 59. ISBN   978-3-322-89449-6. OCLC   913628429.{{cite book}}: CS1 maint: location missing publisher (link)
  10. "Wärmeaustausch zwischen Körpern in Physik". Lernhelfer (Duden) (in German). Retrieved 2022-10-31.