Rubber pad forming

Last updated
Rubber pad forming process, 1: bottom of the press. 2: lower die. 3: sheet metal. 4: rubber pad. 5: top of the press. Rubber press animation.gif
Rubber pad forming process, 1: bottom of the press. 2: lower die. 3: sheet metal. 4: rubber pad. 5: top of the press.

Rubber pad forming (RPF) is a metalworking process where sheet metal is pressed between a die and a rubber block, made of polyurethane. Under pressure, the rubber and sheet metal are driven into the die and conform to its shape, forming the part. The rubber pads can have a general purpose shape, like a membrane. Alternatively, they can be machined in the shape of die or punch.

Contents

Rubber pad forming is a deep drawing technique that is ideally suited for the production of small and medium-sized series. Deep drawing makes it possible to deform sheet metal in two directions, which offers great benefits in terms of function integration, weight reduction, cleanability and such.

The disadvantage of regular deep drawing is that expensive tools consisting of an upper and lower mold are needed. Once these tools have been made, the variable costs are low, which makes regular deep drawing very suitable for large and very large numbers of products.

Technique

In the rubber pad forming process only a milled lower die is required on which a metal plate is placed. Afterwards, the shape of the lower die is pressed in the plate with the rubber mold. In most cases, the contour, hole patterns and the like will be cut with a 3D laser cutter.

Rubber pad press formed product Rubberpers Product.png
Rubber pad press formed product

The simplicity of the rubber press tool causes tooling costs to be around 85 to 90% lower than those of regular deep drawing while the variable costs are higher. This combination makes rubber pad pressing very suitable for smaller and medium-sized series (up to 5,000-10,000 pieces per year), even though traditional cutting, lace, welding, finishing etc. is used more due to the unfamiliarity with rubber pad forming.

Rubber pad forming has been used in production lines for many years. Up to 60% of all sheet metal parts in the aerospace industry are fabricated using this process. The most relevant applications are indeed in the aerospace field. [1] It is frequently used in prototyping shops and for the production of kitchenware. [2] For a decade, rubber pad pressing has developed greatly into a widely used technology for many industrial applications.

Pressing power

8000 tons rubber pad press 8000 Ton Pers.jpg
8000 tons rubber pad press

Enormous pressing forces are required for the rubber presses to work. In the Netherlands there are several rubber pad presses, of which the largest one has a press force of no less than 8,000 tons with a maximum surface area of 1.10x2.20m, these presses are used for very diverse industrial applications.[ citation needed ]

Worldwide, presses are in use up to about 14,000 tonnes.[ citation needed ]

Pros and cons

In summary, the benefits of rubber pad pressing are:

And the disadvantages:

Definition

Rubber pad forming can be accomplished in many different ways, and as technology has advanced, so have the applications for this simple process. In general, an elastic upper die, usually made of rubber, is connected to a hydraulic press. A rigid lower die, often called a form block, provides the mold for the sheeted metal to be formed to. Because the upper (male) die can be used with separate lower (female) dies, the process is relatively cheap and flexible. The worked metal is not worn as quickly as in more conventional processes such as deep drawing, [3] however, rubber pads exert less pressure in the same circumstances as non-elastic parts, which may lead to less definition in forming, and rubber pads wear more quickly than steel parts. [3]

The Guerin process

The Guerin process, also called Guerin Stamping, is a manufacturing process used in the shaping of sheet metals. It is the oldest and most basic of the production rubber-pad forming processes. [3] It was developed in the late 1930s by Henry Guerin, an employee of the Douglas Aircraft Co. in California. Thereafter, it was used extensively by all major aircraft manufacturers to shape the many complex shapes inherent in the design of aircraft. [4]

Variants and similar processes

Related Research Articles

<span class="mw-page-title-main">Powder metallurgy</span> Process of sintering metal powders

Powder metallurgy (PM) is a term covering a wide range of ways in which materials or components are made from metal powders. PM processes are sometimes used to reduce or eliminate the need for subtractive processes in manufacturing, lowering material losses and reducing the cost of the final product. This occurs especially often with small metal parts, like gears for small machines. Some porous products, allowing liquid or gas to permeate them, are produced in this way. They are also used when melting a material is impractical, due to it having a high melting point, or an alloy of two mutually insoluble materials, such as a mixture of copper and graphite.

A die is a specialized machine tool used in manufacturing industries to cut and/or form material to a desired shape or profile. Stamping dies are used with a press, as opposed to drawing dies and casting dies which are not. Like molds, dies are generally customized to the item they are used to create.

<span class="mw-page-title-main">Extrusion</span> Process of pushing material through a die to create long symmetrical-shaped objects

Extrusion is a process used to create objects of a fixed cross-sectional profile by pushing material through a die of the desired cross-section. Its two main advantages over other manufacturing processes are its ability to create very complex cross-sections; and to work materials that are brittle, because the material encounters only compressive and shear stresses. It also creates excellent surface finish and gives considerable freedom of form in the design process.

Thermoforming is a manufacturing process where a plastic sheet is heated to a pliable forming temperature, formed to a specific shape in a mold, and trimmed to create a usable product. The sheet, or "film" when referring to thinner gauges and certain material types, is heated in an oven to a high-enough temperature that permits it to be stretched into or onto a mold and cooled to a finished shape. Its simplified version is vacuum forming.

<span class="mw-page-title-main">Vacuum forming</span> Thermoforming of plastic material

Vacuum forming is a simplified version of thermoforming, where a sheet of plastic is heated to a forming temperature, stretched onto a single-surface mould, and forced against the mould by a vacuum. This process can be used to form plastic into permanent objects such as turnpike signs and protective covers. Normally draft angles are present in the design of the mould to ease removal of the formed plastic part from the mould.

<span class="mw-page-title-main">Sheet metal</span> Metal formed into thin, flat pieces

Sheet metal is metal formed into thin, flat pieces, usually by an industrial process.

<span class="mw-page-title-main">Hydroforming</span> Method of shaping metal through pressurized water

Hydroforming is a means of shaping ductile metals such as aluminium, brass, low alloy steel, and stainless steel into lightweight, structurally stiff and strong pieces. One of the largest applications of cost-effective hydroforming is the automotive industry, which makes use of the complex shapes made possible by hydroforming to produce stronger, lighter, and more rigid unibody structures for vehicles. This technique is particularly popular with the high-end sports car industry and is also frequently employed in the shaping of aluminium tubes for bicycle frames.

<span class="mw-page-title-main">Compression molding</span> Method of molding

Compression molding is a method of molding in which the molding material, generally preheated, is first placed in an open, heated mold cavity. The mold is closed with a top force or plug member, pressure is applied to force the material into contact with all mold areas, while heat and pressure are maintained until the molding material has cured; this process is known as compression molding method and in case of rubber it is also known as 'Vulcanisation'. The process employs thermosetting resins in a partially cured stage, either in the form of granules, putty-like masses, or preforms.

Spin casting, also known as centrifugal rubber mold casting (CRMC), is a method of utilizing inertia to produce castings from a rubber mold. Typically, a disc-shaped mold is spun along its central axis at a set speed. The casting material, usually molten metal or liquid thermoset plastic, is then poured in through an opening at the top-center of the mold. The filled mold then continues to spin as the metal solidifies.

This article is a list of terms commonly used in the practice of metalworking – the science, art, industry, and craft of shaping metal.

<span class="mw-page-title-main">Stamping (metalworking)</span> Forming metal sheets with a stamping press

Stamping is the process of placing flat sheet metal in either blank or coil form into a stamping press where a tool and die surface forms the metal into a net shape. Stamping includes a variety of sheet-metal forming manufacturing processes, such as punching using a machine press or stamping press, blanking, embossing, bending, flanging, and coining. This could be a single stage operation where every stroke of the press produces the desired form on the sheet metal part, or could occur through a series of stages.

<span class="mw-page-title-main">Bending (metalworking)</span> Metalworking to produce a V-, U- or channel shape

Bending is a manufacturing process that produces a V-shape, U-shape, or channel shape along a straight axis in ductile materials, most commonly sheet metal. Commonly used equipment include box and pan brakes, brake presses, and other specialized machine presses. Typical products that are made like this are boxes such as electrical enclosures and rectangular ductwork.

<span class="mw-page-title-main">Deep drawing</span> Metalworking process

Deep drawing is a sheet metal forming process in which a sheet metal blank is radially drawn into a forming die by the mechanical action of a punch. It is thus a shape transformation process with material retention. The process is considered "deep" drawing when the depth of the drawn part exceeds its diameter. This is achieved by redrawing the part through a series of dies.

Metal bellows are elastic vessels that can be compressed when pressure is applied to the outside of the vessel, or extended under vacuum. When the pressure or vacuum is released, the bellows will return to its original shape, provided the material has not been stressed past its yield strength. They are used both for their ability to deform under pressure and to provide a hermetic seal that allows movement.

Hot pressing is a high-pressure, low-strain-rate powder metallurgy process for forming of a powder or powder compact at a temperature high enough to induce sintering and creep processes. This is achieved by the simultaneous application of heat and pressure.

Hot metal gas forming (HMGF) is a method of die forming in which a metal tube is heated to a pliable state, near to but below its melting point, then pressurized internally by a gas in order to form the tube outward into the shape defined by an enclosing die cavity. The high temperatures allow the metal to elongate, or stretch, to much greater degrees without rupture than are possible in previously utilized cold and warm forming methods. In addition, the metal can be formed into finer details and requires less overall forming force than traditional methods.

Formability is the ability of a given metal workpiece to undergo plastic deformation without being damaged. The plastic deformation capacity of metallic materials, however, is limited to a certain extent, at which point, the material could experience tearing or fracture (breakage).

<span class="mw-page-title-main">Metal spinning</span> Metalworking process

Metal spinning, also known as spin forming or spinning or metal turning most commonly, is a metalworking process by which a disc or tube of metal is rotated at high speed and formed into an axially symmetric part. Spinning can be performed by hand or by a CNC lathe.

<span class="mw-page-title-main">Liquid Impact Forming</span> Metalworking process

Liquid Impact Forming is a metalworking process in which the combined use of a stamping press and a liquid medium forms the desired shape on the workpiece. This technique is a synthesis of two metalworking processes; stamping (metalworking) and hydroforming. It is especially suited for the cold forming of tubular structural parts in automotive, railroad and aerospace industries.

References