SANS 164

Last updated
SANS 164-1 (old, left) and -2 (new, right) sockets SANS 164-1 & 164-2 sockets.jpg
SANS 164-1 (old, left) and -2 (new, right) sockets

South African National Standard 164: Plugs and socket outlets for household and similar purposes for use in South Africa is the South African Bureau of Standards' standard for domestic AC power plugs and sockets. As a former British colony, South Africa's electricity standards are of British derivation, and it uses 220/230 V at 50 Hz AC. [1]

However, while the UK changed over to the rectangular-pin BS 1363 plug after World War II, South Africa has retained the older round-pin BS 546 style. [2] This round-pin style was current in both the UK and South Africa when South Africa gained independence in 1931. [3]

Consequently, through much of the rest of the 20th century, both the smaller BS 546 5 ampere plug and socket, [4] and the larger BS 546 15 ampere plug and socket, [4] remained commonly in use in South Africa until the SANS 164-1 and SANS 164-2 standards were strictly defined in 1992. In 1994 these two new modern SANS 164 standards were implemented. [2] Through the 1980s and into the 1990s the SANS 164-1/BS 546 15 ampere standard was largely in the process of replacing the smaller BS 546 5 ampere standard, [2] and thus it became the most prominently utilised standard from 1994 on.

South Africa has adopted the IEC 60906-1 plug and socket as SANS 164-2 in 1992. More recently however it has been selected by the South African Government as the "preferred standard" in 2013, and is being pushed to slowly replace the SANS 164-1/BS 546 15 ampere standard. [5] Although the sockets are compatible with the Europlugs, which are already in common use as SANS 164-5, and Brazil has adopted a modified form of the same IEC 60906-1 standard, South Africa is the first country to adopt the IEC 60906-1 standard directly and implement it. [6]

The standard is divided into seven parts: [4]

SANS 164-0: General and Safety Requirements [7] [8]
This incorporates IEC 60884 for definitions and general requirements. First implemented in 2006, [9] it effectively replaces an earlier separate standard set by the South African Bureau of Standards (SABS for short) for plug and socket safety (SABS 1664). [10] [11]
SANS 164-1 and -3 (BS 546) plugs BS 546 Plugs - 15A 5A 2A.png
SANS 164-1 and -3 (BS 546) plugs

SANS 164-1: Conventional System, 16 A 250 V [12] [13]
16A SANS 164-1 travel adaptor. To be used in "Type M" sockets. Type M travel adaptor.jpg
16A SANS 164-1 travel adaptor. To be used in "Type M" sockets.
This is identical to the BS 546 15 ampere plug and socket, although in South Africa it is rated for 16 A for compatibility with the IEC 60898 standard current ratings. By 1992 [14] the BS 546 15 ampere system had been codified by the SABS as SANS 164-1. This standard remains in effect today [13] and it is the most commonly used plug and socket system currently in use in South Africa. However, after a transition period of 10 to 20 years, it is planned that SANS 164-2 will replace SANS 164-1 as the dominant standard. [15] [6]
This plug-and-socket system is equivalent to the IEC " Plug Type M " system. [16]

SANS 164-2: Conventional System, 16 A 250 V [17] [18]
This specifies the IEC 60906-1 plug system, both 2-pin unearthed and 3-pin earthed. Codified by the SABS as a South African standard since 1992, [14] it was designated the "preferred standard" in 2013. [5] Since 2015, South Africa has been in a planned transition period lasting 10 to 20 years (till either 2025 or 2035) to replace SANS 164-1 with SANS 164-2 as the dominant plug and socket system. [15] [6] The sockets are compatible with the SANS 164-5 Europlug which is also currently in common use in South Africa.
This plug-and-socket system is equivalent to the IEC " Plug Type N " system. [19]

SANS 164-3: Conventional System, 6 A 250 V [20] [21]
This is identical to the BS 546 5 ampere plug and socket, although it is rated for 6 A in South Africa for compatibility with the IEC 60898 standard current ratings. This standard was first codified by the SABS in 2006. [22] Although the SABS standard was only defined in 2006, plugs and sockets of this form are normally only found in older installations of South African households, as both the BS 546 5 ampere (equivalent to SANS 164-3) and the BS 546 15 ampere (equivalent to SANS 164-1) were common in South Africa until 1992, when SANS 164-1 became the dominant standard for most household applications. [14] Thus, plugs and sockets of the SANS 164-3/BS 546 5 ampere type are not commonly seen in households in South Africa anymore, having largely been replaced by SANS 164-1 in the early 1990s.
This plug-and-socket system is equivalent to the IEC " Plug Type D " system. [23]

SANS 164-4: Dedicated System, 16 A 250 V [24] [25]
These plugs and sockets, unique to South Africa, [2] are similar to the SANS 164-1 connectors, but have the earth pin flattened on one side to prevent conventional plugs from being inserted into dedicated sockets. Dedicated plugs are, however, compatible with conventional sockets. This standard was first codified by the SABS in 2006. [22]
These receptacles are commonly used for uninterruptible, isolated or otherwise filtered power. They come in three varieties, with corresponding colours. Although the standard does not define their use, some are common: [2]
  • Red, flat on top: Generic "special power", commonly used for computers and other electronics
  • Blue, flat rotated 53° clockwise: commonly used for uninterruptible power
  • Black, flat rotated 53° counterclockwise: commonly used for transformer-isolated power

SANS 164-5: Two-pole, non-rewireable plugs, 2,5 A 250 V AC, with cord, for connection of class II equipment [26] [27]
These plugs are identical to the CEE7/16 Alternative II Europlug. Only plugs are defined; they are to be used with SANS 164-2 or 164-6 sockets. [4] This standard was first codified in South Africa by the SABS in 2006. [22]
This plug is equivalent to the plug defined by the IEC as " Plug Type C " (Europlug). [28]

SANS 164-6: Two-pole systems, 16 A 250 V AC, for connection of class II equipment [29] [30]
These plugs are the CEE-7/17 unearthed type, compatible with CEE 7/1 (unearthed), CEE 7/3 (Schuko), and CEE 7/5 (French style) sockets. Corresponding unearthed sockets are also defined, which include features to prevent the insertion of earthed CEE 7/4, 7/6 and 7/7 plugs. South Africa resolves the problem with Schuko's unreliable earthing by forbidding its use on devices which require earthing. [31] This standard was first codified in South Africa by the SABS in 2006. [22]

The last two categories allow many European electrical devices to be imported directly.

Images

Related Research Articles

<span class="mw-page-title-main">British Standards</span> Standards produced by BSI Group

British Standards (BS) are the standards produced by the BSI Group which is incorporated under a royal charter and which is formally designated as the national standards body (NSB) for the UK. The BSI Group produces British Standards under the authority of the charter, which lays down as one of the BSI's objectives to:

Set up standards of quality for goods and services, and prepare and promote the general adoption of British Standards and schedules in connection therewith and from time to time to revise, alter and amend such standards and schedules as experience and circumstances require.

<span class="mw-page-title-main">DC connector</span> Electrical connector for carrying DC power

A DC connector is an electrical connector for supplying direct current (DC) power.

<span class="mw-page-title-main">IEC 60320</span> Set of standards for AC power connectors used on domestic appliances on the appliance side

IEC 60320 Appliance couplers for household and similar general purposes is a set of standards from the International Electrotechnical Commission (IEC) specifying non-locking connectors for connecting power supply cords to electrical appliances of voltage not exceeding 250 V (a.c.) and rated current not exceeding 16 A. Different types of connector are specified for different combinations of current, temperature and earthing requirements. Unlike IEC 60309 connectors, they are not coded for voltage; users must ensure that the voltage rating of the equipment is compatible with the mains supply. The standard uses the term coupler to encompass connectors on power cords and power inlets and outlets built into appliances.

<span class="mw-page-title-main">Schuko</span> Type of AC power plug and socket

"Schuko" refers to a plug/socket system used in much of Europe and in many countries east of there. It is a registered trademark referring to a system of AC power plugs and sockets that is defined as "CEE 7/3" (sockets) and "CEE 7/4" (plugs). A Schuko plug features two round pins of 4.8 mm diameter for the line and neutral contacts, plus two flat contact areas on the top and bottom side of the plug for protective earth (ground). The socket has a predominantly circular recess which is 17.5 mm deep with two symmetrical round apertures and two earthing clips on the sides of the socket positioned to ensure that the earth is always engaged before live pin contact is made. Schuko plugs and sockets are symmetric AC connectors. They can be mated in two ways, therefore line can be connected to either pin of the appliance plug. As with most types of European sockets, Schuko sockets can accept Europlugs. Schuko plugs are considered a very safe design when used with Schuko sockets, but they can also mate with other sockets to give an unsafe result.

AC power plugs and sockets connect electric equipment to the alternating current (AC) mains electricity power supply in buildings and at other sites. Electrical plugs and sockets differ from one another in voltage and current rating, shape, size, and connector type. Different standard systems of plugs and sockets are used around the world.

<span class="mw-page-title-main">IEC 60309</span> International standard for industrial plugs

IEC 60309 is a series of international standards from the International Electrotechnical Commission (IEC) for "plugs, socket-outlets and couplers for industrial purposes". They are also referred to as "pin & sleeve" connectors in North America or as "CeeForm" connectors in the entertainment industry. The maximum voltage allowed by the standard is 1000 V DC or AC; the maximum current, 800 A; and the maximum frequency, 500 Hz. The ambient temperature range is −25 °C to 40 °C.

<span class="mw-page-title-main">Mains electricity by country</span>

Mains electricity by country includes a list of countries and territories, with the plugs, voltages and frequencies they commonly use for providing electrical power to low voltage appliances, equipment, and lighting typically found in homes and offices. Some countries have more than one voltage available. For example, in North America the supply to most premises is split-phase, with 240 volts between phases and 120 volts between either phase and neutral. Most sockets are connected to 120 V and neutral. By connecting across the phases, 240 V is available for large appliances. Often different sockets are mandated for different voltage or current levels.

<span class="mw-page-title-main">Industrial and multiphase power plugs and sockets</span>

Industrial and multiphase plugs and sockets provide a connection to the electrical mains rated at higher voltages and currents than household plugs and sockets. They are generally used in polyphase systems, with high currents, or when protection from environmental hazards is required. Industrial outlets may have weatherproof covers, waterproofing sleeves, or may be interlocked with a switch to prevent accidental disconnection of an energized plug. Some types of connectors are approved for hazardous areas such as coal mines or petrochemical plants, where flammable gas may be present.

<span class="mw-page-title-main">Europlug</span> Type of electrical plug

The Europlug is a flat, two-pole, round-pin domestic AC power plug, rated for voltages up to 250 V and currents up to 2.5 A. It is a compromise design intended to connect low-power Class II appliances safely to the many different forms of round-pin domestic power socket used across Europe. However, it is not compatible with the rectangular-pin BS 1363 sockets found in Cyprus, Gibraltar, Singapore, Malaysia, United Arab Emirates, Hong Kong, Ireland, Malta and the United Kingdom. Europlugs are non-rewirable and must be supplied attached to a power cord.

<span class="mw-page-title-main">IEC 60906-1</span>

IEC 60906-1 is an international standard designed "to provide a standard for a safe, compact and practical 16 A 250 V AC system of plugs and socket-outlets that could be accepted by many countries as their national standard, even if not in the near future." The standard was originally published by the International Electrotechnical Commission in 1986; the current edition is ed2.0 published in 2009. Although it is almost identical to the Swiss SEV 1011 T12 plug for 10 A 250 V a.c. standardised in 1937, its dimensions are slightly different and its polarization is flipped. As of July 2014, only South Africa has introduced a standard based closely on IEC 60906-1. Brazil used it as the basis for its NBR 14136 standard, but this is not compatible with IEC 60906-1. In 2017 the European Union (EU) published recommendations advising against the harmonisation of domestic plug and socket systems in the EU.

<span class="mw-page-title-main">AS/NZS 3112</span> AC power plug and socket used in Australia and New Zealand

AS/NZS 3112 is the harmonised Australian and New Zealand standard for AC power plugs (male) and sockets (female). The standard is used in Australia, Argentina, New Zealand, Fiji, Tonga, Solomon Islands, Papua New Guinea and several other Pacific island countries. The International Electrotechnical Commission (IEC) "world plugs" Web site calls this plug Type I.

GOST 7396 is a series of Soviet and later Russian standards that specify basic dimensions and safety requirements for power plugs and sockets used in Russia and other former Soviet Republics, as well as for export to markets that use American or British plugs.

<span class="mw-page-title-main">IEC 62196</span> International standards for vehicle charging technology

IEC 62196Plugs, socket-outlets, vehicle connectors and vehicle inlets – Conductive charging of electric vehicles is a series of international standards that define requirements and tests for plugs, socket-outlets, vehicle connectors and vehicle inlets for conductive charging of electric vehicles and is maintained by the technical subcommittee SC 23H “Plugs, Socket-outlets and Couplers for industrial and similar applications, and for Electric Vehicles” of the International Electrotechnical Commission (IEC).

<span class="mw-page-title-main">AC power plugs and sockets: British and related types</span> AC power plug type

Plugs and sockets for electrical appliances not hardwired to mains electricity originated in the United Kingdom in the 1870s and were initially two-pin designs. These were usually sold as a mating pair, but gradually de facto and then official standards arose to enable the interchange of compatible devices. British standards have proliferated throughout large parts of the former British Empire.

<span class="mw-page-title-main">Type 2 connector</span> Electric vehicle charging connector in Europe

The IEC 62196 Type 2 connector is used for charging electric vehicles, mainly within Europe, as it was declared standard by the EU. Based on widespread red IEC 60309 three phase plugs with five pins, which come in different diameters according to maximum current, a single size was selected, as maximum possible power will be communicated to the car via two additional communication pins and by a simple resistor coding within the cable. The onboard charger inside the car has to limit the current accordingly.

Today there are approximately 20 types in common use around the world, and many obsolete socket types are still found in older buildings.

CEE 7 is a standard for alternating-current plugs and sockets. First published in 1951 by the former International Commission on the Rules for the Approval of Electrical Equipment (IECEE), it unified standards produced by several continental European countries. The 2nd edition was published in 1963 and last updated in March 1983. It remains available from the IEC, but they state that "this standard shall not be used alone, it is to be used in addition to IEC 60884-1".

<span class="mw-page-title-main">SN 441011</span> Swiss standard for AC power plugs and sockets

SN 441011, until 2019 SEV 1011, is the Swiss national standard for AC power plug for domestic use and similar purposes. The plug SN 441011 Type 12 and the socket SN 441011 Type 13 are also known internationally as Type J.

<span class="mw-page-title-main">Type 3 connector</span> Electric vehicle charging connector in Europe

The IEC 62196 Type 3 connector is used for charging battery electric vehicles, mainly within France and Italy, as it was one of three AC plug standards described in IEC 62196-2. The Type 3 connector comes in two physical formats, Type 3A for single-phase (230V) and Type 3C for single- and three-phase (400V) alternating current (AC) power. Both have since been superseded by the Type 2 connector, the latter adopted as sole connector in 2013 by the European Union. The Type 1 connector is the corresponding AC connector standard used in North America, Japan, and South Korea.

References

  1. ↑ "Power plug, socket & mains voltage in South Africa". WorldStandards.eu. Retrieved 2022-09-25.
  2. 1 2 3 4 5 Oud, Oof. "South Africa: overview of types of plugs and sockets". Digital Museum of Plugs and Sockets. Retrieved 2017-05-21.
  3. ↑ Herrman, John (2009-10-29). "Giz Explains: Why Every Country Has a Different F#$%ing Plug". Gizmodo . Retrieved 2017-05-22.
  4. 1 2 3 4 "SANS 164 standards: a working group perspective" (PDF). Vector: 66–68. April 2008.
  5. 1 2 Blaine, Sue (2014-01-28). "SA to switch to new, safer plugs". Business Day Live. Archived from the original on 2014-10-22.
  6. 1 2 3 Sanderson, Sertan (14 February 2014). "South Africa to switch over to new electric plug standard". The South African. Retrieved 2017-05-22.
  7. ↑ Africa, Standards South (2006). Plug and socket-outlet systems for household and similar purposes for use in South Africa Part 0: General and safety requirements (PDF) (1 ed.). Standards South Africa. ISBN   0-626-17847-9. SANS 164-0:2006.
  8. ↑ SANS 164-0:2017. SABS. 2017. ISBN   978-0-626-34135-0 . Retrieved 2 March 2018.
  9. ↑ "Catalog: Numerical List of Standards" (PDF). SABS.co.za . 2013. p. 641. Retrieved 2 March 2018.
  10. ↑ "Catalog: Withdrawn Standards" (PDF). SABS.co.za . 2013. p. 57. Retrieved 2 March 2018.
  11. ↑ "Catalog: Numerical List of Standards" (PDF). SABS.co.za . 2013. p. 595. Retrieved 2 March 2018.
  12. ↑ Africa, Standards South (2006). Plug and socket-outlet systems for household and similar purposes for use in South Africa Part 1: Conventional system, 16 A 250 V a.c. (PDF) (5 ed.). Standards South Africa. ISBN   0-626-17837-1. SANS 164-1:2006.
  13. 1 2 SANS 164-1:2016. SABS. 2016. ISBN   978-0-626-32182-6 . Retrieved 2 March 2018.
  14. 1 2 3 "Catalog: Numerical List of Standards" (PDF). SABS.co.za . 2013. p. 102. Retrieved 2 March 2018.
  15. 1 2 Akabor, Nafisa (24 January 2014). "SA to get new electrical sockets, plugs". TechCentral. Retrieved 2017-05-22.
  16. ↑ "Plug Type M". IEC.ch . Retrieved 2 March 2018.
  17. ↑ Africa, Standards South (2006). Plug and socket-outlet systems for household and similar purposes for use in South Africa Part 2: IEC system, 16 A 250 V a.c. (PDF) (3 ed.). Standards South Africa. ISBN   0-626-17849-5. SANS 164-2:2006.
  18. ↑ SANS 164-2:2012. SABS. 2012. ISBN   978-0-626-34906-6 . Retrieved 2 March 2018.
  19. ↑ "Plug Type N". IEC.ch . Retrieved 2 March 2018.
  20. ↑ Africa, Standards South (2007). Plug and socket-outlet systems for household and similar purposes for use in South Africa Part 3: Conventional system, 6 A 250 V a.c. (1.1 ed.). Standards South Africa. ISBN   978-0-626-20796-0. SANS 164-3:2007.
  21. ↑ SANS 164-3:2017. SABS. 2017. ISBN   978-0-626-34150-3 . Retrieved 2 March 2018.
  22. 1 2 3 4 "Catalog: Numerical List of Standards" (PDF). SABS.co.za . 2013. p. 642. Retrieved 2 March 2018.
  23. ↑ "Plug Type D". IEC.ch . Retrieved 2 March 2018.
  24. ↑ Africa, Standards South (2007). Plug and socket-outlet systems for household and similar purposes for use in South Africa Part 4: Dedicated system, 16 A 250 V a.c. (1.1 ed.). Standards South Africa. ISBN   978-0-626-20797-7. SANS 164-4:2007.
  25. ↑ SANS 164-4:2017. SABS. 2017. ISBN   978-0-626-34134-3 . Retrieved 2 March 2018.
  26. ↑ Africa, Standards South (2008). Plug and socket-outlet systems for household and similar purposes for use in South Africa Part 5: Two-pole, non-rewireable plugs, 2,5 A 250 V a.c., with cord, for connection of class II equipment (1.1 ed.). Standards South Africa. ISBN   978-0-626-20853-0. SANS 164-5:2008.
  27. ↑ SANS 164-5:2007. SABS. 2007. ISBN   978-0-626-36264-5 . Retrieved 2 March 2018.
  28. ↑ "Plug Type C". IEC.ch . Retrieved 2 March 2018.
  29. ↑ Africa, Standards South (2008). Plug and socket-outlet systems for household and similar purposes for use in South Africa Part 6: Two-pole systems, 16 A 250 V a.c., for connection of class II equipment (1.1 ed.). Standards South Africa. ISBN   978-0-626-21785-3. SANS 164-6:2008.
  30. ↑ SANS 164-6:2017. SABS. 2017. ISBN   978-0-626-34906-6 . Retrieved 2 March 2018.
  31. ↑ VC 8008 2010. Government Gazette. 19 November 2010. p. 42. Retrieved 2 March 2018– via Archive.org.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.