Technique used for timing symbols on a digital interface
Source-Synchronous clocking refers to a technique used for timing symbols on a digital interface. Specifically, it refers to the technique of having the transmitting device send a clock signal along with the data signals. The timing of the unidirectional data signals is referenced to the clock (often called the strobe) sourced by the same device that generates those signals, and not to a global clock (i.e. generated by a bus master). Compared to other digital clocking topologies like system-synchronous clocks, where a global clock source is fed to all devices in the system, a source-synchronous clock topology can attain far higher speeds.
A reason that source-synchronous clocking is useful is that it has been observed that all of the circuits within a given semiconductor device experience roughly the same process-voltage-temperature (PVT) variation. This means signal propagation delay experienced by the data through a device tracks the delay experienced by the clock through that same device over PVT. This advantage allows higher speed operation as compared to the traditional technique of providing the clock from a third device to both the transmitter and the receiver. Another benefit is that higher complexity data-recovery or clock-data-recovery circuits (such as PLLs) are not required when this technique is used.
Or rather than higher clock speeds, large systems that take advantage of source-synchronous clocking can have the benefit of a higher tolerance of PVT variation of its individual components.
Timing Analysis
Synchronous logic elements such as flip-flops have static timing criteria that must be satisfied in order for them to work correctly. In a system-synchronous clock topology where a skew-aligned clock is fed to all devices, the criteria are
A source-synchronous clock topology eliminates two of these factors, and . The former is eliminated since both clock and data signals are driven by identical flip-flops on the same silicon at the same temperature and voltage, thereby equalizing the seen by both clock and data. The latter is eliminated for the same reason - since the clock and data are driven by identical devices and (ideally) connected with wires of equal length, the skew between clock and data is greatly reduced. For this reason, can be reduced significantly. Since frequency is inversely proportional to clock period, the clock frequency increases as a result.
Drawbacks
One drawback of using source-synchronous clocking is the creation of a separate clock-domain at the receiving device, namely the clock-domain of the strobe generated by the transmitting device. This strobe clock-domain is often not synchronous to the core clock domain of the receiving device. For proper operation of the received data with other data already present in the device, an additional stage of synchronization logic is required to transfer the received data into the core clock-domain of the receiving device. This stage can often be found alongside source synchronous logic. This usually results in greater system complexity compared to globally clocked systems, but the benefits are generally much greater than this increase in complexity.
Implementation Variations
In bi-directional data transfer buses, two opposing unidirectional strobes can be sent from each device. Often the strobe is free running in this case. That is, the strobe continues to toggle whether there is data being transferred or not.
Another variation is the sharing of the same bus to transfer the strobe. In this case the strobe can only be transferred by the device that is sending the data and may require transmission of pre-ambles and post-ambles to indicate the start and end of the strobes. (Example: DDR2).
In large ASICs or processors, multiple strobes and data groups (data bits that are associated to the same strobe) may exist between the same two devices to account for the slightly different PVT variations in different regions of the same die.
Double Data Rate Synchronous Dynamic Random-Access Memory is a double data rate (DDR) synchronous dynamic random-access memory (SDRAM) class of memory integrated circuits used in computers. DDR SDRAM, also retroactively called DDR1 SDRAM, has been superseded by DDR2 SDRAM, DDR3 SDRAM, DDR4 SDRAM and DDR5 SDRAM. None of its successors are forward or backward compatible with DDR1 SDRAM, meaning DDR2, DDR3, DDR4 and DDR5 memory modules will not work on DDR1-equipped motherboards, and vice versa.
Low-voltage differential signaling (LVDS), also known as TIA/EIA-644, is a technical standard that specifies electrical characteristics of a differential, serial signaling standard. LVDS operates at low power and can run at very high speeds using inexpensive twisted-pair copper cables. LVDS is a physical layer specification only; many data communication standards and applications use it and add a data link layer as defined in the OSI model on top of it.
In electronics and especially synchronous digital circuits, a clock signal is an electronic logic signal which oscillates between a high and a low state at a constant frequency and is used like a metronome to synchronize actions of digital circuits. In a synchronous logic circuit, the most common type of digital circuit, the clock signal is applied to all storage devices, flip-flops and latches, and causes them all to change state simultaneously, preventing race conditions.
In telecommunication and data transmission, serial communication is the process of sending data one bit at a time, sequentially, over a communication channel or computer bus. This is in contrast to parallel communication, where several bits are sent as a whole, on a link with several parallel channels.
Serial Peripheral Interface (SPI) is a de facto standard for synchronous serial communication, used primarily in embedded systems for short-distance wired communication between integrated circuits.
JTAG is an industry standard for verifying designs of and testing printed circuit boards after manufacture.
Synchronous and asynchronous transmissions are two different methods of transmission synchronization. Synchronous transmissions are synchronized by an external clock, while asynchronous transmissions are synchronized by special signals along the transmission medium.
Asynchronous circuit is a sequential digital logic circuit that does not use a global clock circuit or signal generator to synchronize its components. Instead, the components are driven by a handshaking circuit which indicates a completion of a set of instructions. Handshaking works by simple data transfer protocols. Many synchronous circuits were developed in early 1950s as part of bigger asynchronous systems. Asynchronous circuits and theory surrounding is a part of several steps in integrated circuit design, a field of digital electronics engineering.
Clock skew is a phenomenon in synchronous digital circuit systems in which the same sourced clock signal arrives at different components at different times due to gate or, in more advanced semiconductor technology, wire signal propagation delay. The instantaneous difference between the readings of any two clocks is called their skew.
In electronics, metastability is the ability of a digital electronic system to persist for an unbounded time in an unstable equilibrium or metastable state. In digital logic circuits, a digital signal is required to be within certain voltage or current limits to represent a '0' or '1' logic level for correct circuit operation; if the signal is within a forbidden intermediate range it may cause faulty behavior in logic gates the signal is applied to. In metastable states, the circuit may be unable to settle into a stable '0' or '1' logic level within the time required for proper circuit operation. As a result, the circuit can act in unpredictable ways, and may lead to a system failure, sometimes referred to as a "glitch". Metastability is an instance of the Buridan's ass paradox.
Static timing analysis (STA) is a simulation method of computing the expected timing of a synchronous digital circuit without requiring a simulation of the full circuit.
The Wishbone Bus is an open source hardware computer bus intended to let the parts of an integrated circuit communicate with each other. The aim is to allow the connection of differing cores to each other inside of a chip. The Wishbone Bus is used by many designs in the OpenCores project.
In integrated circuit design, dynamic logic is a design methodology in combinational logic circuits, particularly those implemented in metal–oxide–semiconductor (MOS) technology. It is distinguished from the so-called static logic by exploiting temporary storage of information in stray and gate capacitances. It was popular in the 1970s and has seen a recent resurgence in the design of high-speed digital electronics, particularly central processing units (CPUs). Dynamic logic circuits are usually faster than static counterparts and require less surface area, but are more difficult to design. Dynamic logic has a higher average rate of voltage transitions than static logic, but the capacitive loads being transitioned are smaller so the overall power consumption of dynamic logic may be higher or lower depending on various tradeoffs. When referring to a particular logic family, the dynamic adjective usually suffices to distinguish the design methodology, e.g. dynamic CMOS or dynamic SOI design.
In digital electronic design a clock domain crossing (CDC), or simply clock crossing, is the traversal of a signal in a synchronous digital circuit from one clock domain into another. If a signal does not assert long enough and is not registered, it may appear asynchronous on the incoming clock boundary.
Quad data rate is a communication signaling technique wherein data are transmitted at four points in the clock cycle: on the rising and falling edges, and at two intermediate points between them. The intermediate points are defined by a second clock that is 90° out of phase from the first. The effect is to deliver four bits of data per signal line per clock cycle.
The front panel data port (FPDP) is a bus that provides high speed data transfer between two or more VMEbus boards at up to 160 Mbit/s with low latency. The FPDP bus uses a 32-bit parallel synchronous bus wired with an 80-conductor ribbon cable.
GDDR3 SDRAM is a type of DDR SDRAM specialized for graphics processing units (GPUs) offering less access latency and greater device bandwidths. Its specification was developed by ATI Technologies in collaboration with DRAM vendors including Elpida Memory, Hynix Semiconductor, Infineon and Micron. It was later adopted as a JEDEC standard.
An incremental encoder is a linear or rotary electromechanical device that has two output signals, A and B, which issue pulses when the device is moved. Together, the A and B signals indicate both the occurrence of and direction of movement. Many incremental encoders have an additional output signal, typically designated index or Z, which indicates the encoder is located at a particular reference position. Also, some encoders provide a status output that indicates internal fault conditions such as a bearing failure or sensor malfunction.
In computing, a logic block or configurable logic block (CLB) is a fundamental building block of field-programmable gate array (FPGA) technology. Logic blocks can be configured by the engineer to provide reconfigurable logic gates.
The Advanced eXtensible Interface (AXI) is an on-chip communication bus protocol and is part of the Advanced Microcontroller Bus Architecture specification (AMBA). AXI had been introduced in 2003 with the AMBA3 specification. In 2010, a new revision of AMBA, AMBA4, defined the AXI4, AXI4-Lite and AXI4-Stream protocols. AXI is royalty-free and its specification is freely available from ARM.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
