.325 Winchester Short Magnum

Last updated
.325 Winchester Short Magnum
WSSM and WSM.jpg
WSM and WSSM family of cartridges. From left to right: .223 WSSM, .243 WSSM, .25 WSSM, .270 WSM, 7 mm WSM, .300 WSM, .325 WSM.
TypeRifle
Place of originUnited States
Service history
In serviceNever issued
Production history
Designer Winchester
Designed2005
ManufacturerWinchester
Produced2005–present
Specifications
Parent case .300 Winchester Short Magnum
Case typeRebated-rimmed, bottleneck
Bullet diameter.323 in (8.2 mm)
Land diameter.315 in (8.0 mm)
Neck diameter.350 in (8.9 mm)
Shoulder diameter.538 in (13.7 mm)
Base diameter.555 in (14.1 mm)
Rim diameter.535 in (13.6 mm)
Case length2.100 in (53.3 mm)
Overall length2.860 in (72.6 mm)
Case capacity83  gr H2O (5.4 cm3)
Rifling twist1 in 10 in (254 mm)
Primer typeLarge rifle magnum
Maximum pressure (C.I.P.)63,091 psi (435.00 MPa)
Maximum pressure (SAAMI)65,000 psi (450 MPa)
Ballistic performance
Bullet mass/typeVelocityEnergy
180 gr (12 g) Ballistic Silvertip3,060 ft/s (930 m/s)3,743 ft⋅lbf (5,075 J)
200 gr (13 g) AccuBond CT2,950 ft/s (900 m/s)3,866 ft⋅lbf (5,242 J)
220 gr (14 g) Power-Point2,840 ft/s (870 m/s)3,941 ft⋅lbf (5,343 J)
Test barrel length: 24 in (610 mm)
Source(s): Winchester Ammunition

The .325 Winchester Short Magnum, commonly known as the 325 WSM, is an 8mm caliber rebated rim bottlenecked centerfire short magnum medium bore cartridge. The cartridge was introduced by Winchester Ammunition in 2005. [1] [2]

Contents

Introduced at the 2005 Shot Show in Las Vegas, NV, it is the largest member of the Winchester Short Magnum family of cartridges. The .325 WSM was intended for the hunting of medium and large bodied thin skinned dangerous and non-dangerous big game animals of Africa, Asia, Europe and North America. [3]

History & Origin

Since the introduction of the .300 WSM in 2000 there had been speculation that Winchester and Browning would release further cartridges based on the cartridge case of the .300 WSM. Then in 2001 Winchester announced the release of the .270 WSM and the 7mm WSM cartridges. The common wisdom indicated that Winchester would release a .33 caliber (8.38 mm) cartridge based on the .300 WSM case. However, Winchester surprised the shooting public in 2002 when they introduced the .223 WSSM and the .243 WSSM based on a further shortened WSM case followed by the .25 WSSM in 2003. [1]

The introduction of the .325 WSM in 2005 took the shooting public by surprise, as the 8mm caliber did not have a following in North America. Earlier introductions of 8mm cartridges in North America were met with failure, as the .30 caliber (7.62 mm) was generally considered the caliber of choice among American hunters. [1]

When introduced, Winchester offered the cartridge loaded with a 180 gr (12 g) Ballistic Silvertip at 3,060 ft/s (930 m/s) (SBST325S), a 200 gr (13 g) Combined Technologies Accubond at 2,950 ft/s (900 m/s) (S325WSMCT), and a 220 gr (14 g) Power-Point at 2,840 ft/s (870 m/s) (X325WSM). [1]

Cartridge design

The .325 WSM uses the .300 WSM case necked up to accept the 8mm bullet. The cartridge was influenced by the .404 Jeffery and contemporary cartridge designs calling for a short, fat cartridge operating at high pressures which could be cycled through a short action rifle. [4] The understanding was that such cartridges would provide greater efficiency and uniformity in burning the powder charge which in turn would promote a greater inherent accuracy of the cartridge. The rebated rim design allows for the cartridge to utilize actions chambered for rifles based on the .375 Holland & Holland bolt face diameter. [5]

The WSM case was designed to be loaded with .30 caliber (7.62mm) bullets. An aspect of the short, fat cartridge design is that it has a narrower acceptable caliber range than a longer cartridge case. It was for this reason that Winchester introduced the WSSM cartridge case to load sub .27 caliber (6.8mm) bullets. During the testing phase, Winchester had found that, when loaded with .33 caliber bullets, the WSM resulted in the loss of performance and settled for the 8mm caliber instead. Winchester determined that the .32 caliber was the largest caliber that provided a “magnum” level of performance in the WSM case.[ citation needed ]

Cartridge dimensions

The .325 Winchester Short Magnum has 5.39 ml (83 grain) H2O cartridge case capacity.

.325 WSM.jpg

.325 Winchester Short Magnum maximum C.I.P. cartridge dimensions. All sizes in millimetres (mm).

Americans would define the shoulder angle at alpha/2 ≈ 35 degrees. The common rifling twist rate for this cartridge is 254 mm (1 in 10 in), 4 grooves, Ø of the lands = 8.00 mm, Ø grooves = 8.20 mm, land width = 4.47 mm and the primer type is large rifle. [6]

According to the official C.I.P. (Commission Internationale Permanente pour l'Epreuve des Armes à Feu Portatives) rulings the .325 Winchester Short Magnum can handle up to 435 MPa (63,091 psi) piezo pressure. In C.I.P. regulated countries every rifle cartridge combo has to be proofed at 125% of this maximum C.I.P. pressure to certify for sale to consumers. [6]

The .325 Winchester Short Magnum is a Delta L problem cartridge, meaning it can present unexpected chambering and/or feeding problems. The Delta L problem article explains this problem in more detail. [6]

The German 8×68mm S cartridge introduced in 1939 is probably the closest ballistic twin of the .325 Winchester Short Magnum. The .325 Winchester Short Magnum is considerably shorter and fatter and has a more radical rebated rim, much steeper shoulder angle and a shorter neck (7.82 mm) than the 8×68mm S. This makes the 8×68mm S case with its 9.11 mm long neck better suited for loading long heavier bullets and due to its sleeker exterior shape bound to cycle more reliably in bolt-action rifles in extreme situations. On the other hand, the proportions of .325 Winchester Short Magnum promote good internal ballistic efficiency that allows the .325 Winchester Short Magnum to fire shorter lighter bullets at slightly higher muzzle velocities whilst using less propellant than the classically proportioned 8×68mm – that has 5.58 ml (86 grains) H2O cartridge case capacity.

Performance

The .325 WSM is an efficient, flat shooting 8mm magnum rifle cartridge. Bullet weights range from 125 to 250 gr (8.1 to 16.2 g). Performance is on par with the two other magnum cartridges: 8mm Remington Magnum and the German 8×68mmS cartridge with lighter weight bullets. However, these later two cartridges have a distinct edge of being able to seat long heavy 220 gr (14 g) bullets without encroaching upon the powder space. Due to the necessity of seating heavier longer bullets more deeply into the powder column due to the short design and maximum overall length of the .325 WSM cartridge, velocity drops off as bullet weight increases. This is particularly evident with mono-metal bullets such as Nosler's E-Tip bullets, and the Barnes X bullets. These bullets are constructed of copper, which is about 20% less density than that of a conventional lead bullet. The resulting mono-metal bullets are typically longer, which requires these bullets to be seated more deeply to meet standards set for the cartridge and allow reliable feeding and cycling of the cartridges in rifles.

8 mm cartridges compared

Maximum muzzle velocity comparison in % of the probably most proliferated European and American 8 mm rifle cartridges out of 650 mm (25.59 in) long barrels loaded with relatively light to heavy 8 mm bullets to their C.I.P. or SAAMI (Sporting Arms and Ammunition Manufacturers’ Institute) sanctioned maximum pressures.

Bullet weight gram (grain)8.23 g (127 gr)9.72 g (150 gr)11.34 g (175 gr)12.96 g (200 gr)14.26 g (220 gr)Case capacity (%)
7.92×57mm Mauser (8×57mm IS)100.0100.0100.0100.0100.0100.0
8×64mm S102.7102.7102.8102.9102.9110.3
.325 WSM108.7109.1109.0109.3111.1131.7
8×68mm S108.4108.5108.7110.5112.3136.5
8mm Rem. Mag.111.9112.3114.5115.3116.0157.1

This comparison is not totally objective since the 8mm Remington Magnum and .325 WSM operate at 448.16 MPa (65000 psi), the 8×68mm S at 440 MPa (63817 psi), the 8×64mm S at 405 MPa (58740 psi) and the 7.92×57mm Mauser at 390 MPa (56564 psi) maximum chamber pressure. Higher chamber pressure results in higher muzzle velocities.

Sporting Use

The .325 WSM should be considered primarily a hunting or sporting cartridge. It was intended to take medium and large bodied, dangerous thin skinned game up to 1,800 pounds (816 kg). Bullets of 180 gr or less are intended for smaller deer species such as white tail and mule deer, while those of 200 gr or more are intended for elk, moose and large bear. The .325 WSM being an 8mm cartridge could find favor among European hunters for elk (European moose), wild boar as its performance is similar to the vaunted 8×68mm S cartridge. The cartridge is useful for all including the largest bear species. Most outfitters recommend at least a .30 to .375 calibre magnum class cartridge (depending on the hunters recoil threshold) for the larger bear species such as the Alaskan brown bear and the polar bear. Due to the flat shooting and long range performance of the .325 WSM it is also a top performer for most African plains game such as kudu, nyala, wildebeest and zebra.

The .325 WSM has not made inroads in competitive shooting sports or military use. However, on the contrary to what some competitive shooters and sportsman believe, and as mentioned above, for reloaders there are quite an array of bullet sizes and shapes to choose from. Bullet weights from 125 gr to 250 gr are offered by premium bullet makers such as Nosler, Sierra, Barnes, Woodleigh, Swift, Hornady and other major manufactures.

Rifles

Winchester Ammunition's release of the .325 WSM was in conjunction with the release by FN Herstal of rifles chambered in the cartridge under the Browning and Winchester brand names. Originally, Winchester released the Ultimate Shadow, Camo Ultimate Shadow, Classic Featherweight, Classic Laminated, Super Grade RMEF (Rocky Mountain Elk Foundation) and Super Grade III in the 325 WSM while Browning chambered the 325 WSM in their A-Bolt, X-Bolt and BAR rifle lines.

Typical rifles for the WSM line of cartridges have barrels between 22–24 in (560–610 mm) which is less than the typical magnum rifle. The short action combined with short barrels allow for a lighter rifle than a standard magnum rifle which would be based on a standard action with a 26 in (660 mm) barrel.

See also

Related Research Articles

<span class="mw-page-title-main">.338 Lapua Magnum</span> Finnish rifle cartridge

The .338 Lapua Magnum is a rimless, bottlenecked, centerfire rifle cartridge. It was developed during the 1980s as a high-powered, long-range cartridge for military snipers. Due to its use in the War in Afghanistan and the Iraq War, the cartridge has become widely available.

<span class="mw-page-title-main">.308 Winchester</span> Rimless, centerfire, bottlenecked rifle cartridge

The .308 Winchester is a smokeless powder rimless bottlenecked rifle cartridge widely used for hunting, target shooting, police, military, and personal protection applications globally. It is similar, but not identical, to the 7.62×51mm NATO cartridge.

<span class="mw-page-title-main">.270 Winchester</span> Rifle cartridge

The .270 Winchester is a rifle cartridge developed by Winchester Repeating Arms Company in 1923 and it was unveiled in 1925 as a chambering for their bolt-action Model 54 to become arguably the flattest shooting cartridge of its day, only competing with the .300 Holland & Holland Magnum, also introduced in the same year.

<span class="mw-page-title-main">7.92×57mm Mauser</span> German military rifle cartridge

The 7.92×57mm Mauser is a rimless bottlenecked rifle cartridge. The 7.92×57mm Mauser cartridge was adopted by the German Empire in 1903–1905, and was the German service cartridge in both World Wars. In its day, the 7.92×57mm Mauser cartridge was one of the world's most popular military cartridges. In the 21st century it is still a popular sport and hunting cartridge that is factory-produced in Europe and the United States.

The .416 Rigby is a rifle cartridge designed in 1911 by London based gunmaker John Rigby & Company, for hunting dangerous game. It is the first cartridge to use a bullet of .416 inch diameter. The rifles, as built by John Rigby & Co., were initially made up on the Magnum Mauser 98 action, although in later years, some were made on standard length actions, a perfect example being the rifle used by legendary professional hunter Harry Selby. Other famous users of the cartridge were Commander David Enderby Blunt, John Taylor, and Jack O'Connor.

<span class="mw-page-title-main">.257 Weatherby Magnum</span> Rifle cartridge

The .257 Weatherby Magnum is a .257 caliber (6.53 mm) belted bottlenecked cartridge. It is one of the original standard length magnums developed by shortening the .375 H&H Magnum case to approx. 2.5 in (64 mm). Of the cartridges developed by Roy Weatherby, the .257 Weatherby Magnum was known to have been his favorite, and the cartridge currently ranks third in Weatherby cartridge sales, after the .30-378 Weatherby Magnum and the .300 Weatherby Magnum.

<span class="mw-page-title-main">.375 H&H Magnum</span> British rifle cartridge

The .375 H&H Magnum, also known as .375 Holland & Holland Magnum, is a medium-bore rifle cartridge introduced in 1912 by London based gunmaker Holland & Holland. The .375 H&H cartridge featured a belt to ensure the correct headspace, which otherwise might be unreliable, given the narrow shoulder of the cartridge case. The cartridge was designed to use cordite which was made in long strands – hence the tapered shape of the case, which, as a beneficial side effect also helped in smooth chambering and extraction from a rifle's breech.

<span class="mw-page-title-main">.300 Winchester Magnum</span> Rifle cartridge

The .300 Winchester Magnum is a belted, bottlenecked magnum rifle cartridge that was introduced by the Winchester Repeating Arms Company in 1963. The .300 Winchester Magnum is a magnum cartridge designed to fit in a standard rifle action. It is based on the .375 H&H Magnum, which has been blown out, shortened, and necked down to accept a .30 caliber (7.62 mm) bullet.

<span class="mw-page-title-main">7mm Remington Magnum</span> Rifle cartridge

The 7mm Remington Magnum rifle cartridge was introduced as a commercially available round in 1962, along with the new Remington Model 700 bolt-action rifle. It is a member of the belted magnum family that is directly derived from the venerable .375 H&H Magnum. The original purpose of the belted magnum concept taken from the .300 H&H Magnum and .375 H&H Magnum, was to provide precise headspace control, since the sloping shoulders, while easing cartridge extraction, were unsuitable for this purpose. Improved cartridge extraction reliability is desirable while hunting dangerous game, in particular when a fast follow-up shot is required. The 7mm Remington Magnum is based on the commercial .264 Winchester Magnum, .338 Winchester Magnum, and .458 Winchester Magnum, which were based on the same belted .300 H&H Magnum and .375 H&H Magnum cases, trimmed to nearly the same length as the .270 Weatherby Magnum.

<span class="mw-page-title-main">8mm Remington Magnum</span> Rifle cartridge

The 8mm Remington Magnum belted rifle cartridge was introduced by Remington Arms Company in 1978 as a new chambering for the model 700 BDL rifle. The 8mm Remington Magnum's parent case is the .375 H&H Magnum. It is a very long and powerful cartridge that cannot be used in standard length actions, such as those that accommodate the .30-06 Springfield.

<span class="mw-page-title-main">8×68mm S</span>

The 8×68mm S rebated rim bottlenecked centerfire rifle cartridge was developed in the 1930s by August Schüler of the August Schüler Waffenfabrik, Suhl, Germany as a magnum hunting cartridge that would just fit and function in standard-sized Mauser 98 bolt-action rifles. The bore has the same lands and grooves diameters as the German 7.92×57mm Mauser service cartridge. This is one of the early examples where a completely new rifle cartridge was developed by a gunsmith to fit a specific popular and widespread type of rifle.

The .260 Remington cartridge was introduced by Remington in 1997. Many wildcat cartridges based on the .308 Winchester case had existed for years before Remington standardized this round.

The 6.5×68mm rebated rim bottlenecked centerfire rifle cartridge and its sister cartridge the 8×68mm S were developed in the 1930s by August Schüler from the August Schüler Waffenfabrik, Suhl, Germany as magnum hunting cartridges that would just fit and function in standard-sized Mauser 98 bolt-action rifles. This is one of the early examples where a completely new rifle cartridge was developed by a gunsmith to fit a specific popular and widespread type of rifle.

The 9.3×64mm Brenneke is a rimless bottlenecked centerfire rifle cartridge designed in 1927 by German gunmaker Wilhelm Brenneke. It is suitable for hunting medium to large game animals in Africa, Asia, Europe, and North America.

<span class="mw-page-title-main">.416 Remington Magnum</span> Rifle cartridge

The .416 Remington Magnum is a .416 caliber (10.57 mm) cartridge of belted bottlenecked design. The cartridge was intended as a dangerous game hunting cartridge and released to the public in 1989. The cartridge uses the case of the 8 mm Remington Magnum as a parent cartridge. When the cartridge was released in 1988, author Frank C. Barnes considered the .416 Remington Magnum to be the "most outstanding factory cartridge introduced in decades".

The 8×64mm S is a rimless bottlenecked centerfire cartridge developed as a military service round for the German Army who never issued it. As is customary in European cartridges the 8 denotes the 8 mm bullet caliber and the 64 denotes the 64 mm (2.52 in) case length.

<span class="mw-page-title-main">.284 Winchester</span> US rifle cartridge

The .284 Winchester is a firearm cartridge, introduced by Winchester in 1963.

<span class="mw-page-title-main">6.5mm Creedmoor</span> Centerfire rifle cartridge

The 6.5mm Creedmoor (6.5×48mm), designated 6.5 Creedmoor by SAAMI, 6.5 Creedmoor by the C.I.P. or 6.5 CM or 6.5 CRDMR for short, is a centerfire rifle cartridge introduced by Hornady in 2007. It was developed by Hornady senior ballistics scientist Dave Emary in partnership with Dennis DeMille, the vice-president of product development at Creedmoor Sports, hence the name. The cartridge is a necked-down modification of the .30 Thompson Center.

The .450 Rigby is a rifle cartridge designed in 1994 by John Rigby & Co. for the hunting of large, thick-skinned dangerous game animals in Africa. The cartridge is based on the .416 Rigby necked up to accept a .458 in (11.6 mm) bullet and is intended for use in magazine rifles. The cartridge should not be confused with .450 Nitro Express which was introduced by Rigby in 1898, and is a rimmed cartridge intended for use in double rifles.

<span class="mw-page-title-main">.30 R Blaser</span>

The .30 R Blaser (7.62×68mmR) is a rimmed bottlenecked centerfire cartridge developed for hunting in 1991 by Gerhard Blenk, the then owner of Blaser Jagdwaffen GmbH and Dynamit Nobel which then owned RWS ammunition.

References

  1. 1 2 3 4 Staff Writer (22 November 2004). "New Winchester 325 WSM". Western Hunter. J & D Outdoor Communications. 6 (7).
  2. "Welcome to The Family — The 325 WSM" (Press release). Morgan, UT: Browning. FN Herstal. 1 Jan 2005.
  3. Hawks, Chuck (2005). "The .325 WSM". chuckhawks.com. GUNS AND SHOOTING ONLINE. Retrieved 8 March 2014.
  4. The .300 Winchester Short Magnum, Allan Jones - December 18, 2018, www.shootingtimes.com
  5. van Zwoll, Wayne (July 2012). "Short Magnum Thunder". Rifle Firepower. Harris Publications Inc.
  6. 1 2 3 "C.I.P. TDCC datasheet 325 WSM" (PDF). cip-bobp.org.