Bennerley Viaduct (originally Ilkeston Viaduct[1] and known informally as the Iron Giant[2]) is a former railway bridge, now a foot and cycle bridge, between Ilkeston, Derbyshire, and Awsworth, Nottinghamshire, in central England. It was completed in 1877 and carried the Great Northern Railway's (GNR) Derbyshire Extension over the River Erewash, which forms the county boundary, and its wide, flat valley. The engineer was Samuel Abbott, who worked under Richard Johnson, the GNR's chief engineer. The site required a bespoke design as the ground would not support a traditional masonry viaduct due to extensive coal mining. The viaduct consists of 16 spans of wrought iron, lattice truss girders, carried on 15 wrought iron piers which are not fixed to the ground but are supported by brick and ashlar bases. The viaduct is 60 feet (18 metres) high, 26 feet (8 metres) wide between the parapets, and over a quarter of a mile (400 metres) long. It was once part of a chain of bridges and embankments carrying the railway for around two miles (three kilometres) across the valley but most of its supporting structures were demolished when the line closed in 1968. The only similar surviving bridge in the United Kingdom is Meldon Viaduct in Devon.
The viaduct opened in January 1878. Its working life was uneventful except for minor damage inflicted by a Zeppelin bombing raid during the First World War. Plans to demolish the viaduct failed because of the cost of dismantling the ironwork and it became a listed building in 1974. After closure, the viaduct received little maintenance and fell into disrepair. Railway Paths, a walking and cycling charity, acquired it for preservation in 2001 but work faltered due to a lack of funding. The viaduct was listed on the Heritage at Risk Register in 2007 and the 2020 World Monuments Watch for its condition and lack of use. A detailed survey was undertaken in 2016 and funding for restoration work was secured in 2019. The work included rebuilding an embankment to allow step-free access. It opened to the public as part of a cycling and walking route in January 2022.
The route involved significant civil engineering works. The Midland Railway already occupied the most obvious paths and so the GNR had to take a more difficult route, which required multiple bridges, tunnels, and viaducts. Among several branches from the main route, one diverged just east of Awsworth and continued north up the Erewash Valley; another served Bennerley Ironworks (since demolished). Bennerley Viaduct was built immediately south of the ironworks site, which is roughly mid-way between Nottingham and Derby. It was the second-largest engineering work on the GNR's East Midlands routes after the Giltbrook Viaduct on the Awsworth branch, which was a more traditional brick viaduct and demolished after the line's closure.[6][7]
Bennerley was one of several wrought iron viaducts built in the period after cast iron fell out of favour for bridge building following the 1847 Dee Bridge disaster, but before steel became commonplace.[3] The crossing of the River Erewash and its wide, flat valley required a bespoke solution—the valley is boggy and undermined by extensive coal workings which were poorly mapped. The ground would not have been able to support a conventional brick or masonry structure. Thus, Bennerley Viaduct was designed to be lightweight to minimise the load on the foundations.[8][9]
The viaduct was designed by Samuel Abbott, a Nottinghamshire-born engineer and the GNR's resident engineer on the Derbyshire Extension, with input from Richard Johnson, the GNR's chief engineer. Abbot and Johnson were also responsible for Handyside Bridge and Friar Gate Bridge in Derby, further west on the same line. The contractor was Benton and Woodiwiss, and the wrought iron was supplied by Eastwood Swingler & Company of Derby.[3][8][10]
Technical drawings of the viaduct, published in The Engineer
Description
Bennerley Viaduct seen from the valley floor on the Nottinghamshire side after reopening
According to Graeme Bickerdike, writing in 2016 in the magazine Rail Engineer, the design was based on the Viaduc de Busseau[fr], opened in 1864, in central France.[11] The bridge deck consists of 16 spans, each 77 feet (23 metres) long and formed from four 8-foot (2.4-metre) deep wrought-iron Warren lattice truss girders braced together horizontally and vertically. The trusses support a series of transverse iron troughs at 2-foot-4-inch (0.71-metre) centres.[1][11][12] Because of the corrugated surface provided by the troughs, the volume of track ballast required was half that of a traditional flat-decked bridge.[13][14] The rails were not fixed to the bridge deck, instead lying directly on the ballast. The bridge deck is enclosed by low wrought-iron latticework parapets.[3][8][11]
The spans are supported on 15 evenly spaced piers of the same height, 56 feet (17 metres). The piers rest on concrete foundations but are not bolted down. They are held in place by blue brick and ashlar bases, which were built around them. The lack of fixity allows slight movement of the structure to compensate for the ground conditions. Any misalignment of the tracks could be rectified by repacking the ballast.[3][8][1][13] The piers are formed of 12 wrought-iron tubular columns, each constructed from four quadrant pieces riveted together.[1] The tubes are arranged in four groups of three. The centre-most two groups consist of a central vertical column with a slightly inclined column either side of it longitudinally; in the two outermost groups the central columns are offset transversely as raking columns to provide lateral support. The tube groups are braced together horizontally and vertically at four stages.[8][1]
The viaduct is 1,421 feet (433 metres) long (over a quarter of a mile), 60 feet (18 metres) above the valley floor in the centre, and 26 feet (8 metres) wide between the parapets. Both ends of the viaduct are supported on brick piers.[3][8] The structure provides a constant 1:100 gradient; the Awsworth end is 15 feet (4.6 metres) higher than the Ilkeston end.[15] It was once the central (and longest) part of a roughly 2-mile (3.2-kilometre) section of raised line over the Erewash Valley. The valley was approached on embankments at each end. At the western (Ilkeston) end, another iron bridge, supported on Bennerley Viaduct's western pier, continues the line of the viaduct across the Erewash Valley line (built by the Midland Railway and still in use); that bridge is a plate girder structure at a 15-degree skew. A brick bridge continued the line over the Erewash Canal towards Derby but this was demolished after the railway's closure. The terminating brick pier at the eastern (Awsworth) end was built into an embankment on which the line continued towards Nottingham. The embankments were also demolished, though stubs remain at both ends and between the viaduct and the canal.[8][13][16] Aside from the demolition of its surrounding structures, the viaduct survives in a largely unaltered state.[8] The Erewash Valley is largely flat, making Bennerley Viaduct the dominant feature in the landscape. The only nearby patch of high ground is Ilkeston town centre, around two miles (three kilometres) to the south.[17]
Features of the viaduct
The latticework parapet where the viaduct crosses the River Erewash
The corrugated bridge deck (seen before the viaduct was converted to a foot and cycle bridge)
The underside of the bridge deck, showing the multiple trusses that make up each segment
The bottom of a pier, showing the concrete and brick base
History
Construction on the viaduct began with the foundations in May 1876 and the work was completed 18 months later in November 1877. The railway line opened in January 1878. The viaduct's operational life was largely uneventful.[8][11]
On 31 January 1916, nine Zeppelin airships of the German Airship Naval Division conducted a bombing raid over the English Midlands known as the Great Midlands Raid. One of these airships, the L.20 (LZ 59), dropped seven high-explosive bombs in the vicinity of Bennerley Viaduct. One landed just to the north of the viaduct on the Midland Railway line at Bennerley Junction, destroying a signal box on the Midland line. One pier of the viaduct was hit by shrapnel, causing superficial damage; the marks are still visible on one of the piers.[11][18]
In the 1960s, the British railway industry, which had been nationalised in the 1950s, was in decline and the Derbyshire Extension was considered unnecessarily duplicative. Passenger services were withdrawn in 1964 and Bennerley Viaduct closed altogether, along with the rest of the line, in 1968 as a result of the Beeching cuts. Most of the other structures carrying the line across the valley were demolished. A contractor was appointed to demolish Bennerley Viaduct but wrought iron cannot be cut up using conventional metal-cutting equipment and it would therefore have to be dismantled piece by piece. The cost was deemed prohibitive and the viaduct remained in situ.[8][4][11][19]
Bennerley Viaduct became part of the closed-line estate, a group of redundant railway structures maintained by the railway authorities to ensure they did not pose a risk to the public. The derelict land around the bridge became a wildlife haven, though the area also attracted anti-social behaviour and there were several incidents involving people attempting to climb the piers and falling off.[20] As a result of the privatisation of British Rail in the 1990s, the viaduct became part of the Historical Railways Estate (or Burdensome Estate), managed by BRB (Residuary) Limited. By that time, there were advanced plans for a conservation group to take ownership of it.[21] In 2001, Railway Paths Ltd, a sister charity of Sustrans formed to conserve redundant railway structures and convert them into walking and cycling paths, purchased the viaduct from BRB (Residuary).[22][23]
Restoration
The bridge deck in 2023, following conversion for pedestrians and cyclists; the raised parapets are where the structure crosses the active railway.
The viaduct was designated a Grade II listed building in 1974, later upgraded to Grade II*. It is listed for its architectural interest, rarity, constructional interest, and completeness. Listed status provides legal protection from demolition or unsympathetic modification.[8] British Rail applied for planning permission to demolish the viaduct in 1975 and 1980, partly due to persistent trespass—there were several incidents of people injuring themselves after falling from the viaduct—but both applications were rejected.[11][23] The viaduct received little maintenance after 1986 and fell into disrepair. Repair and conservation schemes were mooted but with little progress.[19] In 2007, the viaduct was added to the Heritage at Risk Register as its condition had deteriorated to the point that it was in danger of irreparable damage,[24][25] and it was the only site in the United Kingdom on the 2020 World Monuments Watch, a list published by the World Monuments Fund to highlight heritage sites "in need of urgent action that demonstrate the potential to trigger social change through conservation".[23][26]
A detailed condition survey was undertaken in 2016, following volunteer work to clear vegetation from the bases of the piers. The survey revealed the viaduct to be in generally good condition. It noted corrosion to the ends of the troughs on the bridge deck, damage to brickwork from frost weathering, and missing rivets among the minor defects.[11] In 2017, the Heritage Lottery Fund gave an initial grant to promote engagement and interpretation, which led to the formation of the Friends of Bennerley Viaduct, a community group which works alongside Railway Paths on the restoration and preservation of the viaduct. An application for further Heritage Lottery funding to enable the viaduct to be opened to the public was rejected at the end of 2017, leaving it with an uncertain future.[23][27] In 2019 Historic England offered £120,000 to cover a funding shortfall, allowing restoration work to begin the following year.[28] Ben Robinson, Historic England's Principal Advisor for Heritage at Risk, said "The importance of this viaduct cannot be underplayed. [It is] a stunning example of the genius of British engineering".[29]
The work included repairs to the ironwork, the bases of the piers, and abutments and partial reconstruction of the parapets at the eastern end. The embankment at the western end was rebuilt to provide ramped access from the Erewash Canal towpath and steps were built from the eastern end with a wheel trough alongside for bicycles.[22][29] The viaduct twice featured on the television series The Architecture the Railways Built, once in the inaugural episode in 2020 and once during the restoration work.[30][31][32] It opened to walkers and cyclists on 13 January 2022 after the completion of work costing £1.7 million, which was contributed by Railway Paths, the Railway Heritage Trust, and others.[19] In January 2023, funding was awarded towards creating ramped access from the Awsworth end.[33]
Appreciation and influence
One of the piers at the western end; the River Erewash is just behind the next pier.
The only other surviving wrought-iron lattice viaduct in the United Kingdom is Meldon Viaduct, near Okehampton, in Devon. Meldon is significantly taller but less than half the length.[3][8][34][35] The railway historians Gordon Biddle and O. S. Nock described Bennerley as "by far the more attractive" of the two.[36] Meldon Viaduct has been significantly altered since it was built, whereas Bennerley is essentially unchanged.[8]Belah Viaduct in Cumbria had a similar design but was demolished shortly after its closure in 1962.[21] Another wrought-iron bridge was Crumlin Viaduct, once Britain's tallest, in South Wales. This too was demolished in the 1960s despite efforts to preserve it.[9][37]
Gregory Beecroft, a senior project surveyor for the British Rail Property Board, described Bennerley Viaduct in a contribution for a 1997 book as "among the least impressive" of several metal viaducts that once stood on the British railway network, contrasting it in particular with Belah Viaduct. He believed that "in retrospect, it is a pity that the resources now to be devoted to Bennerley could not have been used to preserve Belah Viaduct.[...] Belah Viaduct closed in 1962, when we were less conscious of our railway heritage, and it was demolished not long after".[21] Historic England calls Bennerley Viaduct "an outstanding survival of the mature phase of development of the railway network in England, demonstrating the confidence of railway engineers in seeking solutions to specific engineering challenges".[8] The journalist Matthew Parris (formerly a Derbyshire MP) visited during restoration work in 2021, and wrote in a column for The Times: "It is, on one view, a hideous thing; and on another a precious and remarkable monument to early railway engineering".[38]
The author D. H. Lawrence grew up in the Erewash Valley and used it as a backdrop to many of his works. He references Bennerley Viaduct in several, most prominently in the novel Sons and Lovers, which includes the lines "There was a faint rattling noise. Away to the right the train, like a luminous caterpillar, was threading across the night. The rattling ceased. 'She's over the viaduct. You'll just do it.'"[20][38]
Sir Thomas Bouch was a British railway engineer. He was born in Thursby, near Carlisle, Cumberland, and lived in Edinburgh. As manager of the Edinburgh and Northern Railway he introduced the first roll-on/roll-off train ferry service in the world. Subsequently as a consulting engineer, he helped develop the caisson and popularised the use of lattice girders in railway bridges. He was knighted after the successful completion of the first Tay Railway Bridge, but his reputation was destroyed by the subsequent Tay Bridge disaster, in which 75 people are believed to have died as a result of defects in design, construction and maintenance, for all of which Bouch was held responsible. He died within 18 months of being knighted.
Ilkeston is a town in the Borough of Erewash, Derbyshire, England, on the River Erewash, from which the borough takes its name, with a population at the 2011 census of 38,640. Its major industries, coal mining, iron working and lace making/textiles, have now all but disappeared.
Langley Mill railway station on the Erewash Valley Line serves the large village of Langley Mill and the towns of Heanor in Derbyshire and Eastwood in Nottinghamshire, England. The station is 12 miles (19 km) north of Nottingham.
Awsworth is a village and civil parish in the Borough of Broxtowe, Nottinghamshire, England. Its population of 2,266 in the 2001 census and 2,204 in that of 2011, further decreasing to 2,166 for the 2021 census. It is a component of the Greater Nottingham area, between Kimberley, Nottinghamshire and Ilkeston, Derbyshire. It has been a civil parish since 1894.
The Derbyshire and Staffordshire extension of the Great Northern Railway was an English railway network built by the GNR to get access to coal resources in the area to the north and west of Nottingham. The Midland Railway had obstructed the GNR in its attempts to secure a share of the lucrative business of transporting coal from the area, and in frustration the GNR built the line. The line was forked: it reached Pinxton in 1875 and a junction with the North Staffordshire Railway at Egginton, approaching Burton on Trent in 1878. The line cut through Derby, resulting in considerable demolition of housing there.
The Erewash Valley Line is a railway line in England, running from Long Eaton, located between Nottingham and Derby, and Clay Cross, near Chesterfield. The southern part was opened by the Midland Railway in 1847 as far as Codnor Park, where it connected to established ironworks, and soon after, a line to Pinxton and Mansfield.
Awsworth railway station was a former railway station in Awsworth, Nottinghamshire. It was opened by the Great Northern Railway on its Derbyshire and Staffordshire Extension in 1875–6.
Eastwood and Langley Mill railway station is a former railway station serving the town of Eastwood and the village of Langley Mill in Derbyshire, England. It was opened by the Great Northern Railway on its Derbyshire Extension in 1875–6.
Ilkeston North railway station was a railway station in Ilkeston, Derbyshire. It was opened by the Great Northern Railway on its Derbyshire Extension in 1878 and closed in 1964.
Giltbrook Viaduct was a railway viaduct built in the Erewash Valley between Awsworth and Giltbrook in Nottinghamshire.
Ilkeston Junction and Cossall railway station was a railway station which served the town of Ilkeston in Derbyshire, England.
Ilkeston Town railway station was a railway station which served the town of Ilkeston in Derbyshire, England. It was opened in 1847 by the Midland Railway.
Handyside Bridge, also known as Derwent Bridge, is a former railway bridge in Darley Abbey, Derbyshire, England which was converted to a foot bridge in 1976 following closure of the railway in 1968.
Meldon Viaduct is a disused railway viaduct crossing the West Okement River at Meldon, 2.5 miles (4.0 km) south-west of Okehampton, on the edge of Dartmoor in Devon, South West England. This truss bridge was constructed from wrought iron, instead of stone or brick arches. It opened in 1874 for a single track; in 1879 its width was doubled for a second track. Although regular services were withdrawn in 1968, the bridge was used for shunting by a local quarry. In the 1990s the remaining single track was removed.
Broadbottom Viaduct is a railway viaduct that spans the River Etherow between Derbyshire and Greater Manchester in England. Originally of wooden construction supported by stone piers, the timber was replaced first with wrought iron box girders, less than 20 years after the viaduct's opening, later followed by steel trusses and more supporting piers.
Friar Gate Bridge, was made by Andrew Handyside & Co is a railway bridge at the end of Friar Gate in the centre of Derby in the East Midlands of England. It was made by Andrew Handyside & Co whose foundry was close to Derby's Handyside Bridge over the River Derwent. The bridge is a remnant of the GNR Derbyshire and Staffordshire Extension ; it formed the approach to Derby Friargate railway station. It is a grade II listed building.
Richard Johnson, MICE was a British railway engineer, latterly chief engineer for the Great Northern Railway (GNR).
Ilkeston is a town and unparished area in the Borough of Erewash in Derbyshire, England. The town and surrounding area contain 29 listed buildings that are recorded in the National Heritage List for England. Of these, one is listed at Grade I, the highest of the three grades, three are at Grade II*, the middle grade, and the others are at Grade II, the lowest grade. The Erewash Canal passes through the area, and the listed buildings associated with it are two bridges and two locks. The other listed buildings include churches and a chapel, a church tower, houses, a museum, the town hall, two factories, a drinking fountain, a brick kiln, a library, cemetery buildings, two cinemas, a school, a railway viaduct, and two war memorials.
Wolverton Viaduct is a railway bridge carrying the West Coast Main Line over the River Great Ouse to the north of Wolverton, part of the Milton Keynes, in south-eastern England. Built in 1838 for the London and Birmingham Railway (L&BR) to the designs of Robert Stephenson, it was the largest viaduct on the L&BR's route. It is in the centre of Wolverton Embankment, itself the largest on the line. It has six brick arches and covers a distance of 660 feet, reaching a maximum height of 57 feet above the river, and terminating in substantial abutments which contain decorative arches. The viaduct and embankment feature in drawings by John Cooke Bourne. Several contemporary commentators likened Stephenson's bridges to Roman aqueducts. Modern engineers and railway historians observed that Wolverton Viaduct is not as innovative or impressive as some that followed but nonetheless praised its visual impact.
Samuel Abbott, MICE was a British railway engineer, born in Calverton, Nottinghamshire on 28 March 1842 and died in Buenos Aires on 17 May 1890. Samuel Abbott was the general manager of the Buenos Aires Great Southern Railway at the time of his death.
References
Bibliography
Barton, Barry (2016). Civil Engineering Heritage: East Midlands. Lincoln: Ruddock's. ISBN9780904327243.
Beecroft, Gregory (1997). "How British Rail Property Board manages the closed-line estate". In Burman, Peter; Stratton, Michael (eds.). Conserving the Railway Heritage. Abingdon: Routledge. ISBN9780419212805.
Biddle, Gordon (2011). Britain's Historic Railway Buildings: A Gazetteer of Structures (Seconded.). Hersham: Ian Allan. ISBN9780711034914.
Biddle, Gordon; Nock, O. S. (1983). The Railway Heritage of Britain: 150 Years of Railway Architecture and Engineering. London: Sheldrake Press. ISBN9780718123550.
Cossons, Neil; Trinder, Barrie (2002). The Iron Bridge: Symbol of the Industrial Revolution (Seconded.). Chichester: Phillimore. ISBN9781860772306.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
