Bristol Phoebus

Last updated

The Bristol Phoebus was an early turbojet engine developed by Bristol Engines. It was based on the gas generator core of the Bristol Proteus. The Phoebus was used for development but only a handful were made. [1] As with other Bristol engines, it took its name from classical mythology.

Contents

Origins

Bristol avoided gas turbine development work at first, as Roy Fedden considered that Bristol's limited wartime resources were already occupied with the enlarged generation of sleeve valve radial engines such as the Hercules and Centaurus then under development and that a useful turbojet engine was at least ten years away. This policy changed under Frank Owner and this became one of the reasons behind Fedden's falling out with Bristol and his departure from them in 1942. [2]

Bristol began gas turbine design work with Owner's 1943 proposal for a 4,000 hp (3,000 kW) turboprop, which became the more modest 2,000 hp (1,500 kW) Theseus. [3] Although the Theseus was manufactured, developed, type tested and actually flew, it never entered service.

Given Bristol's experience with large radials for heavy transport aircraft, they chose to address the same applications for their first turbine engines, thus chose turboprops rather than the turbojets for fast fighters which all the other manufacturers were developing. In late 1944 work began on another turboprop, the Proteus.

For the Bristol Type 172 fast jet bomber [4] and also with an eye to post-war developments and the likelihood of jet travel in fast airliners, Bristol had considered the need for a suitable pure turbojet engine. This B.E.10 engine, which would eventually become the Olympus, began as initial concepts in 1946. [5] [6] Bristol recognised that their lack so far of experience with pure-jet engines could be overcome by developing the core of the Proteus, the compressor, combustion chambers and first turbine, as a stand-alone jet engine. [1] In hindsight, the Phoebus compressor also gave valuable lessons for the design of the Proteus. [7]

Development

Existence of the Pheobus I[ sic ] and Proteus had been announced to the public by 4 September 1947, although no details were made available. [8] Details of the Proteus, and its relation to the Phoebus, did not appear until 1948, [9] and full details not for two years. [10]

To achieve the high design power of the Proteus it was designed with a high overall pressure ratio, using both axial and centrifugal compressors. A twelve stage axial compressor was followed by two centrifugal stages. Despite the widely-admired Theseus installation in the Hermes V and its four petal nacelle with good access for maintenance, the Proteus I was designed to be buried deep within the wing of the Bristol Brabazon or the Saunders-Roe Princess, [10] leading to its unusual reverse-flow layout, with two 180 degree turns in direction. The wing leading edge air inlets would feed air to the rear of the engine, forwards through the compressors, around an internal elbow and then rearwards again through the combustors and turbines. [11] The Proteus was an early free-turbine turboshaft, with separate turbines to drive the compressor and propeller. As a turbojet, the Phoebus did not require the second turbine and the first turbine could be used almost unchanged to produce the simpler jet engine. To achieve the design power needed for the Proteus, a mass-airflow rate of 40 lb/s (18 kg/s) at 10,000 rpm was required, with an overall pressure ratio of 9. [7] This was anticipated to give the Phoebus a thrust of 2,540 lbf (11.3 kN). [11]

The Phoebus made its first flight in February 1949. [12] An Avro Lincoln, RA643, was used, with the engine installed in the bomb bay. [1] [13] [14] Two air inlet elbows were provided at the sides of the bomb bay, with the jet exhaust angled steeply downwards. As the Phoebus used the same reverse-flow layout as the first Proteus, inlets from the side were appropriate.

Initial performance of both the Phoebus and Proteus was poor. A difficulty first encountered with the Phoebus was with the first centrifugal compressor stage. Airflow through it was so poor, owing to a mismatch with the axial compressor, that its effect was to reduce airflow, rather than compressing it. [7] Production engines abandoned this first stage compressor in favour of a better designed diffuser passage which recovered the mass flow, at the cost of dropping the pressure ratio to 5.35.

One of the first tasks for Stanley Hooker, who came to Bristol from Rolls-Royce in Derby at the start of 1949, [15] was to rework the Proteus. The work to totally redesign the Proteus 2 would be so substantial, and take so long, that the Phoebus became an irrelevance: no longer comparable as a prototype, and not worth redesigning to match the new turboprop. Nor did it show any promise for development as a turbojet in its own right, as Hooker was working on the BE.10, later to become the Olympus, which, unlike the troublesome Proteus, was a powerful and reliable success from the outset.

Development of the Phoebus had ceased by 1953, after a cost of £600,000. [16]

Related Research Articles

<span class="mw-page-title-main">Turboprop</span> Turbine engine driving an aircraft propeller

A turboprop engine is a turbine engine that drives an aircraft propeller.

Turbofan Airbreathing jet engine designed to provide thrust by driving a fan

The turbofan or fanjet is a type of airbreathing jet engine that is widely used in aircraft propulsion. The word "turbofan" is a portmanteau of "turbine" and "fan": the turbo portion refers to a gas turbine engine which achieves mechanical energy from combustion, and the fan, a ducted fan that uses the mechanical energy from the gas turbine to force air rearwards. Thus, whereas all the air taken in by a turbojet passes through the combustion chamber and turbines, in a turbofan some of that air bypasses these components. A turbofan thus can be thought of as a turbojet being used to drive a ducted fan, with both of these contributing to the thrust.

<span class="mw-page-title-main">Turbojet</span> Airbreathing jet engine, typically used in aircraft

The turbojet is an airbreathing jet engine, typically used in aircraft. It consists of a gas turbine with a propelling nozzle. The gas turbine has an air inlet which includes inlet guide vanes, a compressor, a combustion chamber, and a turbine. The compressed air from the compressor is heated by burning fuel in the combustion chamber and then allowed to expand through the turbine. The turbine exhaust is then expanded in the propelling nozzle where it is accelerated to high speed to provide thrust. Two engineers, Frank Whittle in the United Kingdom and Hans von Ohain in Germany, developed the concept independently into practical engines during the late 1930s.

Bristol Theseus 1940s British turboprop aircraft engine

The Theseus was the Bristol Aeroplane Company's first attempt at a gas-turbine engine design. A turboprop delivering just over 2,000 hp (1,500 kW) was chosen rather than compete with companies that were already developing turbojets. A heat exchanger to transfer waste heat from the exhaust to the compressor exit was necessary to meet a requirement for a fuel consumption comparable to a piston engine. The heat exchanger was abandoned after tests showed it had a high pressure loss and saved much less fuel than had been expected.

Bristol Proteus 1940s British turboprop aircraft engine

The Bristol Proteus was the Bristol Engine Company's first mass-produced gas turbine engine design, a turboprop that delivered just over 4,000 hp (3,000 kW). The Proteus was a reverse-flow gas turbine. Because the second turbine drove no compressor stages, but only the propeller, this engine was classified as a free-turbine. It powered the Bristol Britannia airliner, small naval patrol craft, hovercraft and electrical generating sets. It was also used to power a land-speed record car, the Bluebird-Proteus CN7. After the merger of Bristol with Armstrong Siddeley the engine became the Bristol Siddeley Proteus, and later the Rolls-Royce Proteus. The Proteus was to have been superseded by the Bristol Orion which would have given a Britannia a 75% increase in power for cruising faster.

Rolls-Royce Olympus Supersonic turbojet engine with afterburner

The Rolls-Royce Olympus was the world's second two-spool axial-flow turbojet aircraft engine design, first run in May 1950 and preceded only by the Pratt & Whitney J57, first-run in January 1950. It is best known as the powerplant of the Avro Vulcan and later models in the Concorde SST.

Pratt & Whitney J57

The Pratt & Whitney J57 is an axial-flow turbojet engine developed by Pratt & Whitney in the early 1950s. The J57 was the first 10,000 lbf (45 kN) thrust class engine in the United States. The J57/JT3C was developed into the J52 turbojet, the J75/JT4A turbojet, the JT3D/TF33 turbofan, and the XT57 turboprop. The J57 and JT3C saw extensive use on fighter jets, jetliners, and bombers for many decades.

<span class="mw-page-title-main">Allison J35</span>

The General Electric/Allison J35 was the United States Air Force's first axial-flow compressor jet engine. Originally developed by General Electric in parallel with the Whittle-based centrifugal-flow J33, the J35 was a fairly simple turbojet, consisting of an eleven-stage axial-flow compressor and a single-stage turbine. With the afterburner, which most models carried, it produced a thrust of 7,400 lbf (33 kN).

Rolls-Royce Derwent 1940s British turbojet aircraft engine

The Rolls-Royce RB.37 Derwent is a 1940s British centrifugal compressor turbojet engine, the second Rolls-Royce jet engine to enter production. It was an improved version of the Rolls-Royce Welland, which itself was a renamed version of Frank Whittle's Power Jets W.2B. Rolls-Royce inherited the Derwent design from Rover when they took over their jet engine development in 1943.

Rolls-Royce Clyde 1940s British turboprop aircraft engine

The Rolls-Royce RB.39 Clyde was Rolls-Royce's first purpose-designed turboprop engine and the first turboprop engine to pass its civil and military type-tests.

Metropolitan-Vickers F.2 Early turbojet engine

The Metropolitan-Vickers F.2 is an early turbojet engine and the first British design to be based on an axial-flow compressor. It was an extremely advanced design for the era, using a nine-stage axial compressor, annular combustor, and a two-stage turbine.

Bristol Orion 1950s British turboprop aircraft engine

The Bristol Orion aero engine was a two-shaft turboprop intended for use in later marks of the Bristol Britannia and the Canadair CL-44. Although the engine was built and underwent a development program, the BE.25 Orion project was cancelled in 1958 by the British Ministry of Supply in favour of the Rolls-Royce Tyne. In addition, interest in turboprop-powered aircraft was beginning to wane, because of the successful introduction of the Boeing 707 and Douglas DC-8 jetliners into airline service.

Heinkel HeS 8

The Heinkel HeS 8 was an early jet engine designed by Hans von Ohain while working at Heinkel. It was the first jet engine to be financially supported by the RLM, bearing the official name 109-001. Had development continued it would have been known as the Heinkel 001, but it does not appear this was used in practice.

<span class="mw-page-title-main">CFE CFE738</span>

The CFE CFE738 is a small turbofan engine aimed at the business/commuter jet market manufactured by the CFE Company, and is used on the Dassault Falcon 2000.

Rolls-Royce RB.50 Trent 1940s British turboprop aircraft engine

The Rolls-Royce RB.50 Trent was the first Rolls-Royce turboprop engine.

Rolls-Royce/Snecma Olympus 593 1960s British/French turbojet aircraft engine

The Rolls-Royce/Snecma Olympus 593 was an Anglo-French turbojet with reheat (afterburners), which powered the supersonic airliner Concorde. It was initially a joint project between Bristol Siddeley Engines Limited (BSEL) and Snecma, derived from the Bristol Siddeley Olympus 22R engine. Rolls-Royce Limited acquired BSEL in 1966 during development of the engine, making BSEL the Bristol Engine Division of Rolls-Royce.

<span class="mw-page-title-main">General Electric T31</span>

The General Electric T31 was the first turboprop engine designed and built in the United States.

Power Jets W.1

The Power Jets W.1 was a British turbojet engine designed by Frank Whittle and Power Jets. The W.1 was built under contract by British Thomson-Houston (BTH) in the early 1940s. It is notable for being the first British jet engine to fly, as the "Whittle Supercharger Type W1", powering the Gloster E.28/39 on its maiden flight at RAF Cranwell on 15 May 1941. The W.1 was superseded by the Power Jets W.2.

The Power Jets WU was a series of three very different experimental jet engines produced and tested by Frank Whittle and his small team in the late 1930s.

During World War 2, the Bristol Aero Engine part of the Bristol Aeroplane Company was pre-occupied with developing and manufacturing radial piston engines, such as the Bristol Hercules and the more powerful Bristol Centaurus. However, in 1944 the Company decided to form a Project Department to investigate the design of gas turbines. Initially the department was based at Tockington Manor, a large country house close to the main factory at Patchway, Bristol. A predominantly young team was formed and was initially tasked with studying turboprop engines.

References

    1. 1 2 3 Baxter, Alan (1990). Olympus - the first forty years. R-RHT. pp. 13–15. ISBN   0-9511710-9-7. Historical Series, Nº15.
    2. ↑ Gunston, Bill (1998). Fedden – the life of Sir Roy Fedden. R-RHT. p. 239. ISBN   1-872922-13-9. Historical Series, Nº26.
    3. ↑ R-RHT, Olympus, p. 10.
    4. ↑ Buttler, Tony (2003). British Secret Projects: Jet Bombers Since 1949 . Midland Publishing. p.  16. ISBN   1-85780-130-X.
    5. ↑ R-RHT, Olympus, p. 13.
    6. ↑ Porter, Andrew (2013). Transatlantic Betrayal. Amberley Publishing. pp. 115–117. ISBN   9781445624297.
    7. 1 2 3 Gunston, Bill (1986). "Bristol". World Encyclopedia of Aero Engines. London: Guild Publishing. pp. 34–35. ISBN   085059717X.
    8. ↑ "British Power Units". Flight : 250. 4 September 1947.
    9. ↑ "Review of 1948". Flight : 772. 30 December 1948.
    10. 1 2 "Bristol Proteus (and Phoebus)". Flight : 313. 8 September 1949.
    11. 1 2 "Designs Of A Decade". Flight : 561. 11 May 1951.
    12. ↑ "Some Outstanding Achievements of 1949". Flight : 455–456. 16 February 1950.
    13. ↑ "Phoebus test bed". Aviation Archive.
    14. ↑ "Ten Thousand Test Flights". Flight : 455–456. 5 April 1957.
    15. ↑ R-RHT, Olympus, p. 18.
    16. ↑ "Costs Reviewed: The Auditor-General on the Proteus, Theseus and Phoebus". Flight : 419. 3 April 1953.
    This page is based on this Wikipedia article
    Text is available under the CC BY-SA 4.0 license; additional terms may apply.
    Images, videos and audio are available under their respective licenses.