The British Rail Class 150 Sprinter is a class of diesel multiple-unit passenger trains, developed and built by British Rail Engineering Limited at York Carriage Works between 1984 and 1987 for use on regional services across Great Britain. The type is a second-generation design, built to more modern standards and based on BR's Mark 3 body design for longer-distance services. It was developed alongside the lower-cost Pacers, which were built using bus parts, for use on short-distance services.[13] Two prototype units were built, followed by 135 production units in two batches. Subsequently, further members of the Sprinter family were developed and introduced to service, including the Class 155, Class 156, Class 158 and Class 159.
By the beginning of the 1980s, British Rail (BR) was operating a large fleet of first-generation DMUs of various designs.[13] While formulating its long-term strategy for this sector of its operations, BR planners recognised that there would be considerable costs incurred by undertaking refurbishment programmes necessary for the continued use of these ageing multiple units, particularly due to the necessity of handling and removing hazardous materials such as asbestos. In light of the high costs involved in retention, planners examined the prospects for the development and introduction of a new generation of DMUs to succeed the first generation.[10]
In the concept stage, two separate approaches were devised, one involving a so-called railbus that prioritised the minimisation of both initial (procurement) and ongoing (maintenance and operational) costs, while the second was a more substantial DMU that could deliver better performance than the existing fleet, particularly on long-distance services.[10] The initial specification developed for the latter type was relatively ambitious for the era, calling for a maximum speed of 90mph (140km/h), a rate of acceleration comparable to contemporary EMUs, the ability to couple/work in multiple with existing EMUs, facilitate through-access for passengers, feature pressure ventilation, the ability to assist another failed unit, and to comprise either a three or four-car consist.[10]
This specification led to the development of the experimental British Rail Class 210diesel-electric multiple unit. However, to deliver the performance specified, it was found that relatively expensive equipment had to be used, particularly to provide sufficient speed, acceleration, and through-passenger access; it also had maintainability problems due to space limitations. Despite these shortcomings, it was recognised that a production fleet that was assembled from proven components would possess both a greater reliability level and lower maintenance costs; it was forecast to achieve an availability rate of 85 percent.[10] As such, the type had sufficiently demonstrated a promising reduction in maintenance costs was achievable, especially once initial teething problems were dealt with, as well as the wider value represented by a new generation of DMUs in the reduction of ongoing costs for BR.[10]
By 1983, experience with the Class 210 had influenced planners to favour the procurement of a new generation of DMUs, but also to adopt a new set of specifications somewhat less demanding than the prior set.[10] Specifically, it was decided to lower the top speed from 90 to 75mph (145 to 121km/h), as testing had shown that the higher rate brought no perceptible improvement in journey times due to the typically short distances between the stations that the type was intended to serve. Furthermore, it was determined that a propulsion system delivering 7hp (5.2kW) per tonne would deliver sufficient acceleration.[10] The requests for compatibility with other rolling stock were eliminated, although auto-coupling and auto-connecting functionality were added. In addition to a good ride quality, the specification included a sound level of 90dB when at full speed, an operational range of 1,000 miles (1,600km), and an interval between major overhauls of five years or 350,000 miles (560,000km).[10]
In comparison to the previous generation of DMUs, which typically used a pair of engines for each power car, the new generation DMU would use only a single engine per car; sufficient cooling was also provided that even with one failed engine, a two-car unit could continue to perform typical services without incurring a major performance deficit.[10] From an operational perspective, it was intended that the DMU could be assembled akin to building blocks, comprising between two and four cars that may or may not be outfitted with various passenger amenities such as toilets and luggage spaces.[10]
Initially formalised as a business specification, these requirements were transferred into a relatively broad technical specification that avoided any specifics other than those deemed essential for compatibility purposes. Thereafter, it was issued to various rolling-stock manufacturers for a competitive tender.[10] As part of this process, these manufacturers submitted bids to construct an initial series of three-car prototypes as demonstration units. A relatively constrained timetable of 18months from the date of order to delivery of these prototypes was also specified; this has been blamed for restricting manufacturers to existing industrial practices for their submissions.[10]
In response to the specification, several submissions were received by BR. The bid submitted by British Rail Engineering Limited (BREL) was heavily based on its successful Class 455 EMU, sharing its body and the majority of its running gear, albeit equipped with two different power trains. The railway engineering company Metro-Cammell also bid, offering its own design that employed rivetted aluminium construction; this feature was credited with enabling a meaningful reduction in weight over conventional methods.[10] BR officials quickly opted to proceed with a pair of prototypes from both BREL and Metro-Cammell, issuing orders to these manufacturers thenceforth.[10]
Design
The Class 150 is a two- or three-car commuter diesel multiple unit. The steel bodyshell is shared with the Class 455 suburban EMU, with doors at 1/3 and 2/3. With the exception of units 150001 and 150002 in their original prototype configurations, each vehicle in the unit is powered by an underframe-mounted 14.01-litre (855-cubic-inch)Cummins six-cylinder turbo-diesel engine that develops 213kW (286hp). The engine drives a Voith T211r hydrokinetic transmission that in turn drives both axles on the inner bogie via a Cardan shaft and Gmeinder GM 180 final drive unit.[14] The design speed is 75mph (121km/h). The majority of units are formed of a DMS (Driving Motor Second - numbered 57xxx) vehicle and a DMSL (Driving Motor Second Lavatory - numbered 52xxx) vehicle. Both vehicles are single class while the DMSL contains the toilet. The two prototype units were built as three-car sets with the addition of a MS (Motor Second) vehicle. In common with other non-intercity stock of the time, the trains lack air conditioning, ventilation being provided though opening hopper windows. As built, passenger seating was in a 3+2 configuration.
The second batch of production vehicles featured a new cab with gangway connection along with a revised interior.
During 1984, BREL constructed a pair of prototype three-car Class 150/0 units, numbered 150001 and 150002; the first unit was delivered to BR only 15 months following the date of order.[10] 150001 was fitted with Cummins engines and Voith hydraulic transmission, and 150002 was fitted with Perkins (Rolls-Royce) engines and a fully automatic gearbox developed by the Self-Changing Gears company.[15] Other than the power train, the two units were identical.[10]
The design specifications of the prototypes were similar to the later production units, but they were to remain as the only Class 150s to be built as three-car units. Additional three-car units were created later by re-marshalling a 150/2 car in the middle of a 150/1 set, but only the prototypes had purpose-built centre cars without driving cabs. Both cab doors are air-operated, unlike the Class 150/1 production model, but seen later on in the 150/2 variant.[citation needed]
150002 proved to be the worse of the two for reliability, and was consequently chosen for use as the testbed for the Class 158, being re-geared to a maximum speed of 90mph (140km/h) and fitted with Cummins engines and Voith transmission, and with a Class 158 interior. One car was fitted with the Class 151 Twin Disc 'hot-shift' transmission, which it used successfully, once the control software was sorted out. To distinguish this unit, it was reclassified as the Class 154. It has since been returned to the standard configuration and reverted to its original number. Both prototypes were still in service with London Midland until 2011. 150001 entered service with First Great Western in January 2012, with 150002 to follow after refurbishment and re-livery. 150001 & 150002 then operated for Great Western Railway. 150001 was based at Bristol's St. Phillips Marsh Depot, primarily working the Bristol Parkway-Weston Super Mare route. 150002 was based at Exeter St. Davids Depot and mainly operated the Riviera Line alongside Class 143 Pacers. In April 2020, both units transferred to Northern's Newton Heath Depot. Both units have since entered into service, initially being used mainly on the Manchester Victoria - Todmorden - Blackburn diagram, and subsequently on Rochdale - Manchester - Bolton - Clitheroe services.
At the same time that BREL built the 150/0s, Metro-Cammell built two prototype Class 151 units at its Washwood Heath plant.[note 4] The two types of unit were exhaustively tested, with a view to placing further orders for the more successful. These tests revealed that the Class 150 had exceptional ride quality, as well as fully meeting the 50 percent engine-out performance requirements.[10] In the event, the two Class 150 units proved to be more reliable and, as a result, an order for 50 two-car units was placed with BREL.
The driving cab layout varies substantially between the subclasses.
This second batch of fifty units was classified as Class 150/1 and numbered in the range 150101-150. Like the prototype units, they did not have the front-end gangway connections which allowed passengers to move between two units that were working in multiple. Originally based at Derby Etches Park depot, these units were introduced in 1985, mainly concentrated around Birmingham and Manchester, and in later years restricted mainly to commuter services.[citation needed]
The final batch of 85 two-car units was built with front-end gangway connections. These units were classified as Class 150/2 and numbered in the range 150201-285. They were used on longer-distance services. The end gangways make them very similar in appearance to the Class 317/2 and Class 455/7 and 455/9 EMUs, also based on the Mark 3 bodyshell.
Some of the Class 150/2 units were later disbanded, and the vehicles were used to make some of the Birmingham and Manchester-based Class 150/1 units into three-car sets. The units in Manchester were later returned to their original configuration, but the Birmingham-based units were renumbered into the 1500xx range by subtracting 100 from the previous number (e.g. 150103 became 150003). This also gave the operational advantage of there being an extra set of passenger door controls within the train for use by the conductor, making it easier to collect revenue without having to run the full length of the unit between stations.[citation needed]
When introduced, the Class 150s had unique interior door open/close buttons. In the north of England, they were square and blue. In the south of Scotland they were yellow in colour and lit up turquoise when enabled. The button lit up bright yellow in the south of England. The illumination feature was intended to aid visually impaired people, although they did not meet the subsequent standards set out by disability regulations that were later introduced, because they had no raised braille and were too small for some disabled people to reasonably locate.[citation needed] During the 2000s, these blue buttons were replaced across the fleet by the standard EAO series 56 'easy to see, easy to press' raised circular door button, with braille writing for the visually impaired, over a yellow surround to comply with the Rail Vehicle Accessibility Regulations.[16]
One further unit was built specifically for testing duties. Originally numbered in the Class 180 series, the unit is now in the departmental Class 950 series, numbered 950001 and carries the yellow Network Rail livery.[citation needed]
The performance of the Class 150 was such that BR decided to procure similar trains for the Provincial fleet, such as the Class 156 and Class 158 for longer regional routes, replacing a significant portion of the locomotive-hauled stock previously operated by BR.[10]
After privatisation, North Western Trains (which was later taken over by First Group and re-branded First North Western shortly afterwards) and Arriva Trains Northern operated Class 150/1 and 150/2s on their routes. The North Western Trains units underwent refurbishment by Hunslet-Barclay in Kilmarnock. The Arriva Trains Northern trains did not. When Northern Rail took over, both the former FNW and ATN Class 150s were transferred to Newton Heath depot, Manchester, with the former North Western Trains Class 158s taking the 150s' places at Northern's Neville Hill depot (Leeds).[17] All Northern 150s contain high-density 2+3 seating. During late 2011, Northern Rail received various ex London Midland 150/1s and 150/2s when the brand-new Class 172 units entered service in the Midlands. This enabled Northern Rail to increase capacity on its most overcrowded services.
In 2015, the then-new Northern franchise (Northern) announced that 24 of their Class 150 units would be reformed into three-car units by March 2019. The three-car sets would be used on routes including the Penistone Line and Leeds to Goole, though this did not end up happening.[18] The current operator, Northern Trains received the Angel Trains 150/0s, previously leased to GWR, on 1 April 2020.
GWR previously operated the two prototype three-car Class 150/0 units, which had transferred from London Midland and replaced the Class 165 and 166Turbo units which were being used on the Reading to Basingstoke Line, which allowed the Turbo units to reinforce Thames Valley services.[19][20] 150001 had entered service in January 2012. The two prototype units later cascaded down to the West fleet in response to the Class 387s taking over from the Class 165s and 166s on the London Paddington to Didcot Parkway services, hence releasing Turbos to take over on the Reading to Basingstoke Line again. Until the end of their operation by GWR, the two 150/0s were based at St Phillips Marsh depot in Bristol and were used on local services around Bristol and Exeter. In April 2020, they transferred to Northern Trains.[citation needed]
Following privatisation, Wales & Borders continued to use the fleet of Class 150 units on branch-line services as well as on the commuter services around Cardiff known as the Valley Lines and the Vale of Glamorgan Line. The units transferred to Arriva Trains Wales in December 2003, with more later acquired for the reopened Ebbw Vale line. All of the ATW units were transferred to KeolisAmey Wales on 14 October 2018 and all KeolisAmey Wales units were transferred to Transport for Wales Rail on 7 February 2021.
In 2010, London Midland ordered Class 172 replacements for its Class 150s. It initially hoped to retain some of the 150s as additional capacity, although they were also wanted by First Great Western and Northern Rail.[21] London Midland was expected to lose all of its Class 150s, but a change in plan saw it retain three Class 150 units as additional capacity, following a statement from the Department for Transport on 10 August 2011. However, London Midland lost two Class 153s to First Great Western as a result.[21]
In July 2023, three Class 150/1s, 150137, 150139 and 150141, were transferred from Northern Trains to London Northwestern Railway for use on the Marston Vale line, after the Class 230s in use on the line were withdrawn from use in December 2022 due to maintenance concerns after the company who maintained the units, Vivarail, went into administration.[22][23] The Class 150s entered service with LNR on 20 November 2023.[24]
Anglia Railways named all bar one unit (150245) of its fleet after famous local figures. On 1 April 2004, Anglia Railways became part of the new 'One' franchise. The Class 150 units were transferred to Arriva Trains Wales (no. 150245) and Central Trains (all other units), having been replaced by Class 156 units from Central Trains.
Silverlink/London Overground
Silverlink liveried, London Overground operated Class 150/1 Sprinter at Gospel Oak in 2008
National Express operated the North London Railways franchise from 1997 under the Silverlink brand. They had eight Class 150s; seven were cascaded from Central Trains following delivery of new Turbostar units in 2000, to replace the ageing fleet of Class 117 and Class 121 units. The eighth unit, no. 150121, was transferred to Silverlink in late 2005.[citation needed]
All units had names.[26][failed verification] The majority of the names are references to the Marston Vale Line on which they operated during Silverlink's franchise: Leslie Crabbe was a long-standing railway employee, who worked on the route; Richard Crane is the chairman of the Bletchley to Bedford Rail Users Association who has campaigned for the line to be retained and expanded.[27] Three of the names (marked with an asterisk) were inherited from the previously incumbent Class 121 units. All the units were then transferred to GWR in 2010 before being transferred again to Arriva Rail North in 2018, and their names are no longer applied.
By the end of October 2010, all London Overground's Class 150/1s had been replaced by a new fleet of eight two-car Class 172 units operating exclusively on the Gospel Oak to Barking Line. Their final use was on 28 October 2010, when unit 150128 formed the 19:02 Barking to Gospel Oak service. The six units were cascaded to First Great Western, together with nine of the London Midland fleet.[28]
Vehicles 52209 and 52212, from units 150209 and 150212 respectively, were scrapped after being damaged in accidents (see §Accidents and incidents)[note 6]
150261 – The Tarka Line – The First 25 Years 1989–2014 (denamed)
150275 – The Yorkshire Regiment – Yorkshire Warrior
Accidents and incidents
On 15 December 1987, 150212 collided with an engineer's crane near Seamer West signal box in North Yorkshire.[36] Carriage 52212 scrapped, 57212 married with 57209 to form 150209.[34]
On 11 November 1988, 150209 derailed at St Helens Central, Merseyside. The train struck the abutment of an overbridge, crushing the leading cab and killing the driver. Sixteen passengers sustained minor injuries.[37] Carriage 52209 scrapped, 57209 married with 57212.[34]
On 12 July 2012, 150217 collided with cattle at Letterston, Pembrokeshire, and was derailed. There were no injuries amongst the 30 passengers and crew on the train.[38]
On 7 November 2015, units 150133 and 150204 formed a passenger train that was derailed near Knaresborough due to a signalman's error.[41][42]
On 3 April 2016, 150219 collided with a stationary InterCity 125 train at Plymouth. Thirty-five people were injured, and both trains were damaged.[43][44][45]
On 3 September 2017, 150217 collided with a tree near Llanbradach in Caerphilly, Wales, at around 10pm. Three people were injured and five fire crews were in attendance.[46]
On 7 February 2018, 150203 divided on the approach to Leeds. There were no injuries, but passengers had to be evacuated across the tracks.[47][48]
On 31 January 2019, 150234 derailed in a low speed derailment at Penryn shortly before 1pm. No injuries were reported. A reduced service was run on the line between Truro and Falmouth until the unit was removed.[49]
On 15 October 2019, 150245 collided with a fallen tree near Spittal, Pembrokeshire and was severely damaged.[50]
On 27 August 2021, 150271 collided with the outrigger of a crane lorry that was obstructing the line at Penistone.[51]
On 26 November 2021, 150284 collided with a fallen tree and was derailed at Balderton, Cheshire.[52]
On 22 May 2022, a train formed of 150240, 150242 and 150279 struck a mini digger near Craven Arms, causing a fuel leak, igniting a fire under one of the carriages. Two units were severely damaged.[53][54]
Notes
↑ The 150/0 Cummins- and Rolls-Royce-powered DMSL and DMS vehicles are described by variations of the relevant master diagrams as the vehicles are otherwise identical, but the MS vehicles have different diagrams because there are significant differences in the seating layout between them.[2]
↑ 150/2 vehicles have bodyshells that are 189.5mm (7.46in) shorter than those of preceding subclasses, to allow for the protrusion of the front gangway. All vehicles of all subclasses have an overall length of 20.060m (65ft 9.8in) when their respective gangway portions are included.[2]
↑ Throughway width of 1,010mm (3ft 4in) for 150/0 vehicles, 1,130mm (3ft 8in) for 150/1 and /2 vehicles.[2]
↑ Further information about the testing and early days of the 150 prototypes with links to the 151s and 154 DMUs at "Class 150 Sprinter Prototype". Archived from the original on 22 August 2006. Retrieved 14 August 2006.
↑ Originally Class 150/1 units 150116, 150112, 150117, and 150147 respectively. 'New' units 150003 and 150004 have vehicles 57209 and 57212 respectively (made available after their matching vehicles from units 150209 and 150212 were scrapped), while unit 150223 was split to provide vehicles 52223 and 57223 for new units 150005 and 150006.[30]
↑ The undamaged matching vehicles, 57209 and 57212, were first formed into a 'replacement' unit 150209, then separated and inserted into First Great Western units 150925 and 150926 respectively in 2012,[34] then removed and in 2021 inserted into units 150116 and 150112 to form 'new' three-car units 150003 and 150004 for Northern Trains.[30]
↑ The previous name, Bletchley Seven, referred to the original fleet of seven Class 150/1 units in the Silverlink fleet.
Related Research Articles
Pacer was the operational name of the British Rail Classes 140, 141, 142, 143 and 144 diesel multiple unit railbuses, built between 1980 and 1987. They were inexpensively developed using a passenger body based on the Leyland National bus on top of a chassis based on the HSFV1 research vehicle. The railbuses were intended as a short-term solution to a shortage of rolling stock, with a lifespan of no more than 20 years. As modernised replacements were lacking, the Pacer fleet remained in service on some lines until 2021 – 37 years after their introduction in 1984.
The British Rail Class 156 Super Sprinter is a diesel multiple unit passenger train. A total of 114 sets were built between 1987 and 1989 for British Rail by Metro-Cammell's Washwood Heath works. They were built to replace elderly first-generation DMUs and locomotive-hauled passenger trains.
The British Rail Class 170 Turbostar is a British diesel multiple unit (DMU) passenger train designed and built by Adtranz, and later by Bombardier Transportation, at Derby Litchurch Lane Works.
The British Rail Class 158Express Sprinter is a diesel multiple unit (DMU) passenger train. It is a member of the Sprinter series of regional trains, produced as a replacement for British Rail's first generation of DMUs; of the other members, the Class 159 is almost identical to the Class 158, having been converted from Class 158 to Class 159 in two batches to operate express services from London Waterloo to the West of England.
The British Rail Class 153 Super Sprinter are single-coach railcars converted from two-coach Class 155 diesel multiple units in the early 1990s. The class was intended for service on rural branch lines, either where passenger numbers do not justify longer trains or to boost the capacity on services with high passenger volume.
The British Rail Class 121 is a single-car double-ended diesel multiple unit. 16 driving motor vehicles were built from 1960, numbered 55020–55035. These were supplemented by ten single-ended trailer vehicles, numbered 56280–56289. They have a top speed of 70 mph (113 km/h), with slam-doors, and vacuum brakes. The driving motor vehicles were nicknamed "Bubble Cars" by some enthusiasts.
The British Rail Class 116 diesel multiple units were built by BR Derby from 1957 to 1961. Introduced as part of the British Railways Modernisation Plan in the mid 1950s, as with other first generation DMUs the 116 was intended to replace steam trains and reduce costs across the rail network. Alongside Metro-Cammell, BR Derby had prior experience with DMUs, having developed a Lightweight Unit, and so was awarded a contract for a new design.
The British Rail Class 323 is a class of electric multiple unit (EMU) passenger train built by Hunslet Transportation Projects and Holec. All 43 units were built from 1992 through to 1995, although mock-ups and prototypes were built and tested in 1990 and 1991.
The British Rail Class 321 is a class of electric multiple unit (EMU) passenger train built by British Rail Engineering Limited's York Carriage Works in three batches between 1988 and 1991 for Network SouthEast and Regional Railways. The class uses alternating current (AC) overhead electrification. The design was successful and led to the development of the similar Class 320 and Class 322.
The Marston Vale line is the line between Bletchley and Bedford in England, a surviving remnant of the former Varsity Line between Oxford and Cambridge, most of which was closed in the late 1960s. The line is sponsored by the Marston Vale community rail partnership. The line is to be adopted and upgraded as part of East West Rail, a project underway to re-establish the Oxford–Cambridge route.
The British Rail Class 144Pacer is a diesel multiple unit (DMU) passenger train built at Derby between 1986 and 1987. British Rail, seeking to procure improved derivatives of the earlier Class 141, placed an order with the manufacturers British Rail Engineering Limited (BREL) and Walter Alexander to construct their own variant, the Class 144. A total of 23 units were constructed. All units have now retired from mainline service, though the majority of the units have been acquired for preservation on heritage railways and in other uses. As of December 2022, 19 out of the 23 units have been purchased following withdrawal for this purpose, of which 14 units are in operational condition.
The British Rail Class 142 Pacer are diesel multiple-unit passenger trains built for British Rail (BR) from 1985 to 1987. They were built with a high level of commonality with the widely-used Leyland National bus. They are part of the Pacer family of railbuses. The last set was withdrawn from service in 2020.
The British Rail Class 43 (HST) is the TOPS classification used for the InterCity 125 High Speed Train diesel-electric power cars, built by British Rail Engineering Limited from 1975 to 1982, and in service in the UK since 1976.
The British Rail Class 143 is a diesel multiple-unit railbus, part of the Pacer family of passenger trains introduced between 1985 and 1986.
The British Rail Class 155 is a diesel multiple unit passenger train. These DMUs were built by Leyland Bus at Workington between 1987 and 1988 as part of BR's replacement of its ageing first-generation diesel fleet. 42 units were originally built, of which only 7 remain; the other 35 units were converted to Class 153 railcars.
The British Rail Class 151 was a prototype class of diesel multiple unit (DMU) developed and constructed by the British railway equipment manufacturer Metro Cammell. It was designed primarily to serve as a successor to the earlier first-generation "Heritage" DMUs operated by the British Rail (BR).
The Sprinter is a family of diesel multiple unit trains in use on the British railway system. They were built in the 1980s and early-1990s by British Rail Engineering Limited (BREL), Metro-Cammell and Leyland. Sprinters operate in almost every part of Great Britain, from rural branch lines to commuter expresses into major cities.
The British Rail Class 172 is a British diesel multiple unit (DMU) passenger train from the Turbostar family, built by Bombardier Transportation's Derby Litchurch Lane Works for use on inner-suburban passenger services. The class is currently operated by West Midlands Railway.
Diesel multiple units and railcars are trains, usually with passenger accommodation, that do not require a locomotive. Railcars can be single cars, while in multiple units cars are marshalled together with a driving position either end. As of December 2010, 23 percent of the rail passenger cars used on Network Rail are part of a diesel multiple unit.
The British Rail Class 230 D-Train is a diesel-electric multiple unit, diesel-battery electric multiple unit or battery electric multiple unit built by rolling stock manufacturer Vivarail for the British rail network. The units are converted from old London Underground D78 Stock, originally manufactured in 1980 by Metro-Cammell, and have been assigned the designation of Class 230 under TOPS.
↑ Bevan Brittan LLC (26 March 2014). The Northern Interim Franchise Agreement(PDF). London: Department for Transport. M-10204941-1. Archived(PDF) from the original on 4 January 2015. Retrieved 22 April 2015.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
