Clamper (electronics)

Last updated December 16, 2023

A clamper (or clamping circuit or clamp) is an electronic circuit that fixes either the positive or the negative peak excursions of a signal to a defined voltage by adding a variable positive or negative DC voltage to it.^[2] The clamper does not restrict the peak-to-peak excursion of the signal (clipping); it moves the whole signal up or down so as to place its peaks at the reference level.

A diode clamp (a simple, common type) consists of a diode, which conducts electric current in only one direction and prevents the signal exceeding the reference value; and a capacitor, which provides a DC offset from the stored charge. The capacitor forms a time constant with a resistor load, which determines the range of frequencies over which the clamper will be effective.

General function

A clamper will bind the upper or lower extreme of a waveform to a fixed DC voltage level. These circuits are also known as DC voltage restorers. Clampers can be constructed in both positive and negative polarities. When unbiased, clamping circuits will fix the voltage lower limit (or upper limit, in the case of negative clampers) to 0 volts. These circuits clamp a peak of a waveform to a specific DC level compared with a capacitively coupled signal, which swings about its average DC level.

The clamping network is one that will "clamp" a signal to a different DC level. The network must have a capacitor, a diode, and optionally a resistive element and/or load, but it can also employ an independent DC supply to introduce an additional shift. The magnitude of R and C must be chosen such that the time constant RC is large enough to ensure that the voltage across the capacitor does not discharge significantly during the interval the diode is nonconducting.

Types

Clamp circuits are categorised by their operation: negative or positive, and biased or unbiased. A positive clamp circuit (negative peak clamper) outputs a purely positive waveform from an input signal; it offsets the input signal so that all of the waveform is greater than 0 V. A negative clamp is the opposite of this—this clamp outputs a purely negative waveform from an input signal. A bias voltage between the diode and ground offsets the output voltage by that amount.

For example, an input signal of peak value 5 V (V_INpeak = 5 V) is applied to a positive clamp with a bias of 3 V (V_BIAS = 3 V), the peak output voltage will be:

V_OUTpeak = 2 × V_INpeak + V_BIAS

V_OUTpeak = 2 × 5 V + 3 V

V_OUTpeak = 13 V

(The peak to peak excursion remains at 10 V.)

Positive unbiased

A positive unbiased clamp.

In the negative cycle of the input AC signal, the diode is forward biased and conducts, charging the capacitor to the peak negative value of V_IN. During the positive cycle, the diode is reverse biased and thus does not conduct. The output voltage is therefore equal to the voltage stored in the capacitor plus the input voltage,^[3] so V_OUT = V_IN + V_INpeak. This is also called a Villard circuit.

Negative unbiased

A negative unbiased clamp

A negative unbiased clamp is the opposite of the equivalent positive clamp. In the positive cycle of the input AC signal, the diode is forward biased and conducts, charging the capacitor to the peak positive value of V_IN. During the negative cycle, the diode is reverse biased and thus does not conduct. The output voltage is therefore equal to the voltage stored in the capacitor plus the input voltage again, so V_OUT = V_IN − V_INpeak.

Positive biased

A positive biased voltage clamp is identical to an equivalent unbiased clamp but with the output voltage offset by the bias amount V_BIAS. Thus, V_OUT = V_IN + (V_INpeak + V_BIAS).

Negative biased

A negative biased voltage clamp is likewise identical to an equivalent unbiased clamp but with the output voltage offset in the negative direction by the bias amount V_BIAS. Thus, V_OUT = V_IN − (V_INpeak + V_BIAS).

Op-amp circuit

The figure shows an op-amp-based clamp circuit with a non-zero reference clamping voltage. The advantage here is that the clamping level is at precisely the reference voltage. There is no need to take into account the forward voltage drop of the diode (which is necessary in the preceding simple circuits as this adds to the reference voltage). The effect of the diode voltage drop on the circuit output will be divided down by the gain of the amplifier, resulting in an insignificant error. The circuit also has a great improvement in linearity at small input signals in comparison to the simple diode circuit and is largely unaffected by changes in the load.

Clamping for input protection

Clamping can be used to adapt an input signal to a device that cannot make use of or may be damaged by the signal range of the original input.

Principles of operation

During the first negative phase of the AC input voltage, the capacitor in a positive clamper circuit charges rapidly. As V_in becomes positive, the capacitor serves as a voltage doubler; since it has stored the equivalent of V_in during the negative cycle, it provides nearly that voltage during the positive cycle. This essentially doubles the voltage seen by the load. As V_in becomes negative, the capacitor acts as a battery of the same voltage of V_in. The voltage source and the capacitor counteract each other, resulting in a net voltage of zero as seen by the load.

Loading

For passive type clampers with a capacitor, followed by a diode in parallel with the load, the load can significantly affect performance. The magnitude of R and C are chosen so that the time constant, $\tau =RC$ , is large enough to ensure that the voltage across the capacitor does not discharge significantly during the diode's non-conducting interval. A load resistance that is too low (heavy load) will partially discharge the capacitor and cause the waveform peaks to drift off the intended clamp voltage. This effect is greatest at low frequencies. At a higher frequency, there is less time between cycles for the capacitor to discharge.

The capacitor cannot be made arbitrarily large to overcome load discharge. During the conducting interval, the capacitor must be recharged. The time taken to do this is governed by a different time constant, this time set by the capacitance and the internal impedance of the driving circuit. Since the peak voltage is reached in one quarter cycle and then starts to fall again, the capacitor must be recharged in a quarter cycle. This requirement calls for a low value of capacitance.

The two conflicting requirements for capacitance value may be irreconcilable in applications with a high driving impedance and low load impedance. In such cases, an active circuit must be used such as the op-amp circuit described above.

Biased versus non-biased

By using a voltage source and resistor, the clamper can be biased to bind the output voltage to a different value. The voltage supplied to the potentiometer will be equal to the offset from zero (assuming an ideal diode) in the case of either a positive or negative clamper (the clamper type will determine the direction of the offset). If a negative voltage is supplied to either positive or negative, the waveform will cross the x-axis and be bound to a value of this magnitude on the opposite side. Zener diodes can also be used in place of a voltage source and potentiometer, hence setting the offset at the Zener voltage.

Examples

Clamping circuits were common in analog television receivers. These sets have a DC restorer circuit, which returns the voltage of the video signal during the "back porch" of the line blanking (retrace) period to 0 V. Low-frequency interference, especially power line hum, induced onto the signal spoils the rendering of the image and, in extreme, cases causes the set to lose synchronization. This interference can be effectively removed via this method.

Related Research Articles

An amplifier, electronic amplifier or (informally) amp is an electronic device that can increase the magnitude of a signal. It is a two-port electronic circuit that uses electric power from a power supply to increase the amplitude of a signal applied to its input terminals, producing a proportionally greater amplitude signal at its output. The amount of amplification provided by an amplifier is measured by its gain: the ratio of output voltage, current, or power to input. An amplifier is defined as a circuit that has a power gain greater than one.

A multivibrator is an electronic circuit used to implement a variety of simple two-state devices such as relaxation oscillators, timers, latches and flip-flops. The first multivibrator circuit, the astable multivibrator oscillator, was invented by Henri Abraham and Eugene Bloch during World War I. It consisted of two vacuum tube amplifiers cross-coupled by a resistor-capacitor network. They called their circuit a "multivibrator" because its output waveform was rich in harmonics. A variety of active devices can be used to implement multivibrators that produce similar harmonic-rich wave forms; these include transistors, neon lamps, tunnel diodes and others. Although cross-coupled devices are a common form, single-element multivibrator oscillators are also common.

An operational amplifier is a DC-coupled high-gain electronic voltage amplifier with a differential input and, usually, a single-ended output. In this configuration, an op amp produces an output potential that is typically 100,000 times larger than the potential difference between its input terminals. The operational amplifier traces its origin and name to analog computers, where they were used to perform mathematical operations in linear, non-linear, and frequency-dependent circuits.

<span class="mw-page-title-main">Rectifier</span> Electrical device that converts AC to DC

A rectifier is an electrical device that converts alternating current (AC), which periodically reverses direction, to direct current (DC), which flows in only one direction. The reverse operation is performed by an inverter.

$<span class="mw-page-title-main">Voltage divider</span> Linear circuit that produces an output voltage that is a fraction of its input voltage$

In electronics, a voltage divider (also known as a potential divider) is a passive linear circuit that produces an output voltage (V_out) that is a fraction of its input voltage (V_in). Voltage division is the result of distributing the input voltage among the components of the divider. A simple example of a voltage divider is two resistors connected in series, with the input voltage applied across the resistor pair and the output voltage emerging from the connection between them.

A voltage multiplier is an electrical circuit that converts AC electrical power from a lower voltage to a higher DC voltage, typically using a network of capacitors and diodes.

A voltage doubler is an electronic circuit which charges capacitors from the input voltage and switches these charges in such a way that, in the ideal case, exactly twice the voltage is produced at the output as at its input.

The Cockcroft–Walton (CW) generator, or multiplier, is an electric circuit that generates a high DC voltage from a low-voltage AC or pulsing DC input. It was named after the British and Irish physicists John Douglas Cockcroft and Ernest Thomas Sinton Walton, who in 1932 used this circuit design to power their particle accelerator, performing the first artificial nuclear disintegration in history. They used this voltage multiplier cascade for most of their research, which in 1951 won them the Nobel Prize in Physics for "Transmutation of atomic nuclei by artificially accelerated atomic particles".

The precision rectifier is a configuration obtained with an operational amplifier in order to have a circuit behave like an ideal diode and rectifier. It is very useful for high-precision signal processing. With the help of a precision rectifier the high-precision signal processing can be done very easily.

This article illustrates some typical operational amplifier applications. A non-ideal operational amplifier's equivalent circuit has a finite input impedance, a non-zero output impedance, and a finite gain. A real op-amp has a number of non-ideal features as shown in the diagram, but here a simplified schematic notation is used, many details such as device selection and power supply connections are not shown. Operational amplifiers are optimised for use with negative feedback, and this article discusses only negative-feedback applications. When positive feedback is required, a comparator is usually more appropriate. See Comparator applications for further information.

A grid leak detector is an electronic circuit that demodulates an amplitude modulated alternating current and amplifies the recovered modulating voltage. The circuit utilizes the non-linear cathode to control grid conduction characteristic and the amplification factor of a vacuum tube. Invented by Lee De Forest around 1912, it was used as the detector (demodulator) in the first vacuum tube radio receivers until the 1930s.

A charge amplifier is an electronic current integrator that produces a voltage output proportional to the integrated value of the input current, or the total charge injected.

In electronics, a clipper is a circuit designed to prevent a signal from exceeding a predetermined reference voltage level. A clipper does not distort the remaining part of the applied waveform. Clipping circuits are used to select, for purposes of transmission, that part of a signal waveform which lies above or below the predetermined reference voltage level.

Ripple in electronics is the residual periodic variation of the DC voltage within a power supply which has been derived from an alternating current (AC) source. This ripple is due to incomplete suppression of the alternating waveform after rectification. Ripple voltage originates as the output of a rectifier or from generation and commutation of DC power.

<span class="mw-page-title-main">Test probe</span>

A test probe is a physical device used to connect electronic test equipment to a device under test (DUT). Test probes range from very simple, robust devices to complex probes that are sophisticated, expensive, and fragile. Specific types include test prods, oscilloscope probes and current probes. A test probe is often supplied as a test lead, which includes the probe, cable and terminating connector.

In the field of electronics, a technique where part of the output of a system is used at startup can be described as bootstrapping.

The single-ended primary-inductor converter (SEPIC) is a type of DC/DC converter that allows the electrical potential (voltage) at its output to be greater than, less than, or equal to that at its input. The output of the SEPIC is controlled by the duty cycle of the control switch (S1).

In electronics, a plate detector is a vacuum tube circuit in which an amplifying tube having a control grid is operated in a non-linear region of its grid voltage versus plate current transfer characteristic, usually near plate current cutoff, to demodulate amplitude modulated carrier signal. This differs from the grid leak detector, which utilizes the non-linearity of the grid voltage versus grid current characteristic for demodulation. It also differs from the diode detector, which is a two-terminal device.

In electronics, power amplifier classes are letter symbols applied to different power amplifier types. The class gives a broad indication of an amplifier's characteristics and performance. The first three classes are related to the time period that the active amplifier device is passing current, expressed as a fraction of the period of a signal waveform applied to the input. This metric is known as conduction angle (θ). A class A amplifier is conducting through all the period of the signal (θ=360°); Class B only for one-half the input period (θ=180°), class C for much less than half the input period (θ<180°). Class D amplifiers operate their output device in a switching manner; the fraction of the time that the device is conducting may be adjusted so a pulse-width modulation output can be obtained from the stage.

The diamond buffer or diamond follower is a four-transistor, two-stage, push-pull, translinear emitter follower, or less commonly source follower, in which the input transistors are folded, or placed upside-down with respect to the output transistors. Like any unity buffer, the diamond buffer does not alter the phase and magnitude of input voltage signal; its primary purpose is to interface a high-impedance voltage source with a low-impedance, high-current load. Unlike the more common compound emitter follower, where each input transistor drives the output transistor of the same polarity, each input transistor of a diamond buffer drives the output transistor of the opposite polarity. When the transistors operate in close thermal contact, the input transistors stabilize the idle current of the output pair, eliminating the need for a bias spreader.

References

↑ Martin Hartley Jones (1995). A Practical Introduction to Electronic Circuits. Cambridge University Press. p. 261. ISBN 978-0-521-47879-3.
↑ Makarov, Sergey N.; Ludwig, Reinhold; Bitar, Stephen J. (27 June 2016). Practical electrical engineering. Switzerland: Springer International. p. 827. ISBN 9783319211732. OCLC 953450203.
↑ Horowitz, Paul; Winfield, Hill (30 March 2015). The Art of Electronics Third Edition. New York: Cambridge University Press. p. 37. ISBN 9780521809269.
↑ S. P. Bali, Linear Integrated Circuits, p.279, Tata McGraw-Hill, 2008 ISBN 0-07-064807-7.