Ferrari 326 MI

Last updated
Ferrari 326 MI
1958-06-29 500 miglia Monza Ferrari 326 MI Hill.jpg
Constructor Ferrari
Designer(s) Carlo Chiti
Vittorio Jano
Technical specifications [1] [2] [3]
Chassis Tubular steel spaceframe
Suspension (front) independent double wishbones, coil springs, hydraulic shock absorbers, anti-roll bar
Suspension (rear) De Dion axle, twin radius arms, coil springs, telescopic shock absorbers
Axle track F: 1,240 mm (48.8 in)
R: 1,240 mm (48.8 in)
Wheelbase 2,220 mm (87.4 in)
Engine Dino 3,210.12 cc (195.9 cu in) 65° V6 naturally-aspirated front-engine, longitudinally mounted
Transmission 3-speed manual transmission
Tyres F: 6.00 x 16
R: 8.00 x 16
Firestone
Competition history
Notable entrants Scuderia Ferrari
Notable drivers Flag of the United States.svg Phil Hill
Debut1958 Race of Two Worlds
EntriesRacesWins Podiums
1100

The Ferrari 326 MI (also known as the 296 MI) was a single-seater manufactured by Ferrari in 1958. It was a one-off race car purpose-built for the second edition of the 500 Miles of Monza. It was one of the two special cars created to compete with American race cars on an Italian race track. Following the naming convention, "326" stood for 3.2-litre, 6-cylinder engine. The "MI" suffix stood for "Monza-Indianapolis". [1] [2]

Contents

Development

The Race of Two Worlds was a short-lived race where the European and American single seaters and sports cars could compete. At Autodromo Nazionale Monza, the organisers prepared special banked curves on a paved oval track in the Indianapolis 500 style. [4] It was the fastest race at that time with a highest speed recorded at 284 km/h (176.5 mph), compared to a record of 235 km/h (146 mph) at the 1958 Indianapolis 500. [2]

Ferrari entered three cars in this race to Indycar regulations. Two of them were specially engineered for the 500 Miles of Monza. The second purpose-built racer after the 412 MI used a modified 246 F1 chassis, featuring a Ferrari-built Dino V6 engine, enlarged to 3.2-litres and was named the 326 MI. The engine was derived from the Dino race car with the largest capacity possible by its crankshaft at 90 mm (3.5 in) of stroke. Ferrari also chose to use the Firestone tyres, just as Americans did. Ferrari was in contract with Belgian Englebert but those tyres were not suitable for a high speed Monza track. [5] [4]

Specifications

Engine and transmission

The 326 MI used a Dino 65° V6 engine, mounted longitudinally in the front. The internal measurements were 87 by 90 mm (3.4 by 3.5 in) of bore and stroke and the resulting total capacity was 3,210.12 cc (3.2 L; 195.9 cu in). It was the biggest capacity and the longest stroke of any Dino V6 in history. With a compression ratio of 10:1, it could produce a maximum power of 330 PS (243 kW; 325 hp) at 7250 rpm. The engine was of a DOHC configuration with two valves per cylinder. Fuel feed was by three Weber 50DCN carburettors. The lubrication system was of a dry sump type. [1] Racing transmission had only three forward speeds. [6]

Chassis and suspension

The 326 MIs tubular steel chassis was derived from the contemporary Ferrari 246 F1 race car with necessary modifications. The front suspension was independent with double unequal-length wishbones, coil springs and hydraulic shock absorbers. At the rear there was a De Dion tube with twin radius arms and coil springs, aided by telescopic shock absorbers. Brakes were of a drum type and fuel tank had a capacity of 166 litres. [1] [3]

Racing

For the 1958 edition of the Race of Two Worlds the Ferrari 326 MI #14 was initially assigned Luigi Musso as a driver. But because Musso had to relieve Mike Hawthorn in the 412 MI #12, Phil Hill was reassigned as a replacement for the 326 MI. Phil Hill's Ferrari was decidedly underpowered and could not match the leading cars. The 326 MI qualified at fourteenth place for the starting grid with a qualification average speed of 259.1 km/h (161 mph). [7] [4]

In the first heat of the actual race, after completing only eleven laps, Phil Hill had to retire due to ignition problems. The sole race of the 326 MI was cut short by a broken magneto. Phil Hill then served as a support for the other Ferrari team with the 412 MI, and in the two remaining heats relieved both drivers. That team finished the race at a third place overall. [8] [7] [4]

The Race of Two Worlds was cancelled and not organised again for the 1959 season. [7]

See also

Other Race of Two Worlds race cars:

Related Research Articles

<span class="mw-page-title-main">Dino (automobile)</span> Motor vehicle

Dino was a marque best known for mid-engined, rear-drive sports cars produced by Ferrari from 1957 to 1976. The marque came into existence in late 1956 with a front-engined Formula Two racer powered by a brand new Dino V6 engine. The name Dino was used for some models with engines smaller than 12 cylinders, it was an attempt by the company to offer a relatively low-cost sports car. The Ferrari name remained reserved for its premium V12 and flat-12 models until 1976, when "Dino" was retired in favour of full Ferrari branding.

<span class="mw-page-title-main">Ferrari Lampredi engine</span> Motor vehicle engine

The Ferrari Lampredi engine was a naturally aspirated all aluminum 60° V12 engine produced between 1950 and 1959. Inline-4 and Inline-6 variants for racing were derived from it.

<span class="mw-page-title-main">Giancarlo Baghetti</span> Italian racing driver

Giancarlo Baghetti was a Formula One driver who raced for the Ferrari, Automobili Turismo e Sport, BRM, Brabham and Lotus teams.

<span class="mw-page-title-main">Ferrari 375 F1</span>

After finding only modest success with the supercharged 125 F1 car in Formula One, Ferrari decided to switch for 1950 to the naturally aspirated 4.5-litre formula for the series. Calling in Aurelio Lampredi to replace Gioacchino Colombo as technical director, Enzo Ferrari directed that the company work in stages to grow and develop an entirely new large-displacement V12 engine for racing.

<span class="mw-page-title-main">Ferrari 195 S</span> Motor vehicle

The Ferrari 195 S was a sports racing car produced by Ferrari in 1950. It was an improved version of the 166 MM. The 195 S won Mille Miglia, Coppa della Toscana and Giro delle Calabria.

<span class="mw-page-title-main">Ferrari 250 S</span> Motor vehicle

The Ferrari 250 S was a sports racing car produced by Ferrari in 1952. It was the first in the long lineage of Ferrari 250 road and race cars powered by a ubiquitous 3.0-litre Colombo V12 engine. In 1952 the 250 S won the Mille Miglia and 12 Hours of Pescara. At the Le Mans, the same year, it clocked the fastest race lap time. Only a single example was produced.

<span class="mw-page-title-main">Ferrari Monza</span> Motor vehicle

The Ferrari Monza is one of a series of cars built by Ferrari. In the early 1950s, Ferrari shifted from using the compact Gioacchino Colombo-designed V12 engine in its smallest class of sports racers to a line of four-cylinder engines designed by Aurelio Lampredi. Inspired by the success of the light and reliable 2.5 L 553 F1 car, the four-cylinder sports racers competed successfully through the late 1950s, culminating with the famed 500 Mondial and 750 Monza.

<span class="mw-page-title-main">Race of Two Worlds</span>

The Race of Two Worlds, also known as the 500 Miglia di Monza, was an automobile race held at the Autodromo Nazionale Monza, Italy in 1957 and again in 1958. It was intended as an exhibition event, allowing American teams from the United States Auto Club (USAC) National Championship to compete directly against teams from the Formula One World Championship based in Europe. The two types of cars competed on the banked oval at Monza which had been completed in 1955. Due to the similarity to the Indianapolis Motor Speedway, where the USAC teams ran the Indianapolis 500, the event earned the nickname Monzanapolis.

<span class="mw-page-title-main">Ferrari 250 Monza</span> Motor vehicle

The Ferrari 250 Monza was a sports racing car produced by Ferrari in 1954. It was a combination of a stretched chassis and body from the line of inline-four-engined racers with an ubiquitous 3.0-litre Colombo V12 engine.

<span class="mw-page-title-main">Ferrari 335 S</span> Motor vehicle

The Ferrari 335 S was a sports racing car produced by Italian manufacturer Ferrari in 1957. The car was a direct response to the Maserati 450S which with its 4.5-litre engine was threatening to overpower the 3.8-litre 315 S and 3.5-litre 290 MM. Four cars were produced in total.

<span class="mw-page-title-main">Ferrari Jano engine</span> Motor vehicle engine

Vittorio Jano designed a new 60° V12 engine for sports car racing for Ferrari. This new engine, introduced in 1956, combined elements of both Colombo and Lampredi engines with new features. Engine architecture was more of Lampredi school but retained smaller Colombo internal measurements. Jano moved to Ferrari along with his designs for the Lancia D50 in 1955 and went on to design not only a new V12 but also a family of the Dino V6 engines soon after. Some of the technical ideas came from the Jano's Lancia V8 DOHC engine, intended for Formula One. This family of engines replaced Lampredi inline-4s known from Ferrari Monza line and went on to win many international races and titles for Ferrari. The design team comprised Jano as well as Vittorio Bellentani, Alberto Massimino, and Andrea Fraschetti.

<span class="mw-page-title-main">Ferrari 376 S</span> Motor vehicle

The Ferrari 376 S was a sports racing car produced by Ferrari in 1955. It was the first raced Ferrari powered by a new Aurelio Lampredi-designed inline-6 engine, created as a larger alternative to the inline-4 series of engines used in the Ferrari Monza race cars. The intention behind the development of this model was the 1955 Mille Miglia race. It was yet another attempt by Ferrari to match the new Mercedes-Benz 300 SLR in competition. All of the created cars were further converted into a bigger capacity models.

<span class="mw-page-title-main">Ferrari 735 LM</span> Motor vehicle

The Ferrari 735 LM was a sports racing car produced by Ferrari in 1955. It was the second raced Ferrari, powered by an Aurelio Lampredi-designed inline-6 engine, created as a larger displacement evolution to the engines used in the Ferrari Monza race cars.

<span class="mw-page-title-main">Ferrari 290 S</span> 1957 sports car

The Ferrari 290 S was a sports racing car produced by Ferrari in 1957. It was a development of an earlier 290 MM race car that won the 1956 Mille Miglia. The 290 S was the first sports car manufactured by Ferrari to be powered by a DOHC V12 engine. Its career was very short but it served as an important milestone in the Jano V12-powered lineage.

<span class="mw-page-title-main">Ferrari 412 MI</span>

The Ferrari 412 MI was a single-seater produced by Italian manufacturer Ferrari in 1958. It was a one-off purpose-built racer for the second edition of the 500 Miles of Monza to compete against American race cars. The 412 MI scored a pole position and finished the race on a third place, which was the best European-entry result. As per naming convention "412" stood for 4-litre, 12-cylinder engine. The "MI" suffix stood for "Monza-Indianapolis".

<span class="mw-page-title-main">Dino 206 S</span> Motor vehicle

The Dino 206 S is a sports prototype produced by Ferrari in 1966–1967 under the Dino marque. Ferrari intended to produce at least fifty examples for homologation by the CSI in the Sport 2.0 L Group 4 category. As only 18 were made, the car had to compete in the Prototype 2.0-litre class instead. In spite of this handicap the Dino 206 S took many class wins. The 206 S was the last of the Dino sports racing cars and simultaneously the most produced.

<span class="mw-page-title-main">Ferrari SP</span> Series of Italian sports prototype racing cars produced by Ferrari during the early 1960s

The Ferrari SP was a series of Italian sports prototype racing cars produced by Ferrari during the early 1960s. All featured a rear mid-engine layout, a first for a Ferrari sports car. Major racing accolades include the 1962 European Hill Climb Championship, two overall Targa Florio victories, in 1961 and 1962, and "1962 Coupe des Sports" title.

<span class="mw-page-title-main">Maserati 420M/58</span>

The Maserati 420M/58Eldorado was a single-seater manufactured by Maserati in 1958. It was a one-off race car purpose-built for the second edition of the 500 Miles of Monza. It was the first single-seater in Europe to be sponsored by a brand not attached to an automobile industry. The internal Maserati classification was the Tipo 4, behind the 250F variants, and also referred to as the 420/M/58 for 4.2-litre displacement, Monoposto or a single-seater in Italian and 1958 year, or simply as the "Eldorado".

<span class="mw-page-title-main">Ferrari 412 S</span> Motor vehicle

The Ferrari 412 S was a unique sports racing car produced by Ferrari in 1958. The 412 S combined Ferrari's most powerful V12 engine to date with a one-off experimental racing chassis. It was also incorrectly called as the 412 MI due to being built around an engine from the 500 Miles of Monza racer. The car was created specifically for John von Neumann to take on the American racing cars Scarabs in SCCA racing. Its famed drivers included Phil Hill and Richie Ginther.

References

  1. 1 2 3 4 "Ferrari 326 MI". formula1.ferrari.com. Retrieved 13 October 2019.
  2. 1 2 3 Acerbi, Leonardo (2012). Ferrari: All The Cars. Haynes Publishing. p. 123.
  3. 1 2 "Specification 326 MI". ferrari-collection.net. Retrieved 13 October 2019.
  4. 1 2 3 4 Laban, Brian (2005). The Ultimate History of Ferrari. Parragon. pp. 162–163.
  5. Nye, Doug (2004). Dino: The Little Ferrari. MotorBooks/MBI Publishing Company. p. 39. ISBN   0-7603-2010-1.
  6. "326 MI". mitorosso.com. Retrieved 13 October 2019.
  7. 1 2 3 Eaton, Godfrey (1983). Ferrari: The Road And Racing Cars. Haynes Publishing. pp. 90–92.
  8. "1958 500 Miglia di Monza Heat 1". champcarstats.com. Retrieved 13 October 2019.

Bibliography