Hammer drill

Last updated
A corded hammer drill next to a drill bit and a chuck key Hammer drill-1.jpg
A corded hammer drill next to a drill bit and a chuck key

A hammer drill, also known as a percussion drill or impact drill, is a power tool used chiefly for drilling in hard materials. [1] [2] It is a type of rotary drill with an impact mechanism that generates a hammering motion. The percussive mechanism provides a rapid succession of short hammer thrusts to pulverize the material to be bored, so as to provide quicker drilling with less effort. If a hammer drill's impact mechanism can be switched off, the tool can be used like a conventional drill to also perform tasks such as screwdriving.

Contents

Function

Hammer drills have a cam-action or percussion hammering mechanism, in which two sets of toothed gears mechanically interact with each other to hammer while rotating the drill bit. With cam-action drills, the chuck has a mechanism whereby the entire chuck and bit move forward and backward on the axis of rotation.

This type of drill is often used with or without the hammer action, but it is not possible to use the hammer action alone as it is the rotation over the cams which causes the hammer motion. A hammer drill has a specially designed clutch that allows it to not only spin the drill bit, but also to punch it in and out (along the axis of the bit).

The actual distance the bit travels in and out and the force of its blow are both very small, and the hammering action is very rapid—thousands of "BPM" (blows per minute) [3] or "IPM" (impacts per minute). Although each blow is of relatively low force, these thousands of blows per minute are more than adequate to break up concrete or brick, using the masonry drill bit's carbide wedge to pulverize it for the spiral flutes to whisk away.

For this reason, a hammer drill drills much faster than a regular drill through concrete, brick, and thick lumber. In standardized drilling speed tests, the most effective hammer drills improve drilling speeds by upwards of 30% compared to completing the same task with the hammer mode disabled. [4] Hammer drills are increasingly powered by cordless technology.

Use

Holes in hard materials are needed for anchor bolts, concrete screws and wall plugs. Hammer drills are not typically used for production construction drilling, but rather for occasional drilling of holes into concrete, masonry or stone. They are also used to drill holes in concrete footings to pin concrete wall forms and to drill holes in concrete floors to pin wall framing. SDS rotary drills are more commonly used as dedicated masonry drilling tools in construction.

Hammer drills almost always have a lever or switch that locks off the special "hammer clutch," turning the tool into a conventional drill for wood or metal work. Hammer drills are more expensive and more bulky than regular drills, but are preferable for applications where the material to be drilled—concrete block or wood studs—is unknown. For example, an electrician mounting an electrical box to a wall would be able to use the same hammer drill to drill into either wood studs (hammer disabled) or masonry walls (hammer enabled).

History

Ancient China's principal drilling technique, [5] percussive drilling, was invented during the Han dynasty. The process involved two to six men jumping on a lever at rhythmic intervals to raise a heavy iron bit attached to long bamboo cables from a bamboo derrick. [6] [7] [8] Utilizing cast iron bits [9] and tools constructed of bamboo, the early Chinese were able to use percussion drilling to drill holes to a depth of 3,000 ft (910 m). The construction of large wells took more than two to three generations of workers to complete. [10] The cable tool drilling machines developed by the early Chinese involved raising and dropping a heavy string of drilling tools to crush through rocks into diminutive fragments. [11] In addition, the Chinese also used a cutting head secured to bamboo rods to drill to depths of 915 m (3,002 ft). [12] The raising and dropping of the bamboo drill strings allowed the drilling machine to penetrate less dense and unconsolidated rock formations. [13]

The origin of the first hammer drill is a matter of contention. German company Fein patented a Bohrmaschine mit elektro-pneumatischem Schlagwerk ("drill with electro-pneumatic striking mechanism") in 1914. German company Bosch produced the first "Bosch-Hammer" around 1932 in mass production. The US company Milwaukee Electric Tool Corporation states that in 1935, it was selling a lightweight 1⁄4 in (6.4 mm) electric hammer drill (cam-action). [14]

Hand-cranked percussion drills were made in the UK in the mid-twentieth century. [15]

See also

Related Research Articles

<span class="mw-page-title-main">Well drilling</span> Method of extracting a natural resource

Well drilling is the process of drilling a hole in the ground for the extraction of a natural resource such as ground water, brine, natural gas, or petroleum, for the injection of a fluid from surface to a subsurface reservoir or for subsurface formations evaluation or monitoring. Drilling for the exploration of the nature of the material underground is best described as borehole drilling.

A power tool is a tool that is actuated by an additional power source and mechanism other than the solely manual labor used with hand tools. The most common types of power tools use electric motors. Internal combustion engines and compressed air are also commonly used. Tools directly driven by animal power are not generally considered power tools.

<span class="mw-page-title-main">Drill</span> Tool used to create holes

A drill is a tool used for making round holes or driving fasteners. It is fitted with a bit, either a drill or driver chuck. Hand-operated types are dramatically decreasing in popularity and cordless battery-powered ones proliferating due to increased efficiency and ease of use.

<span class="mw-page-title-main">Drill string</span> Drill pipe that transmits drilling fluid

A drill string on a drilling rig is a column, or string, of drill pipe that transmits drilling fluid and torque to the drill bit. The term is loosely applied to the assembled collection of the smuggler pool, drill collars, tools and drill bit. The drill string is hollow so that drilling fluid can be pumped down through it and circulated back up the annulus.

<span class="mw-page-title-main">Drill bit</span> Type of cutting tool

Drill bits are cutting tools used in a drill to remove material to create holes, almost always of circular cross-section. Drill bits come in many sizes and shapes and can create different kinds of holes in many different materials. In order to create holes drill bits are usually attached to a drill, which powers them to cut through the workpiece, typically by rotation. The drill will grasp the upper end of a bit called the shank in the chuck.

<span class="mw-page-title-main">Jackhammer</span> Pneumatic tool

A jackhammer is a pneumatic or electro-mechanical tool that combines a hammer directly with a chisel. It was invented by William McReavy, who then sold the patent to Charles Brady King. Hand-held jackhammers are generally powered by compressed air, but some are also powered by electric motors. Larger jackhammers, such as rig-mounted hammers used on construction machinery, are usually hydraulically powered. These tools are typically used to break up rock, pavement, and concrete.

Dremel is a multinational brand of power tools, focusing on home improvement and hobby applications. Dremel is known primarily for its rotary tools, such as the Dremel 3000, 4000 and 8200 series, which are similar to the pneumatic die grinders used in the metalworking industry by tool or moldmakers. Dremel later expanded its product range and now produces butane tools, benchtop and hand-held saws and oscillating tools. The company was purchased by Robert Bosch GmbH in 1993, and is now a division of the Robert Bosch Tool Corporation.

<span class="mw-page-title-main">Drilling rig</span> Integrated system to drill wells

A drilling rig is an integrated system that drills wells, such as oil or water wells, or holes for piling and other construction purposes, into the earth's subsurface. Drilling rigs can be massive structures housing equipment used to drill water wells, oil wells, or natural gas extraction wells, or they can be small enough to be moved manually by one person and such are called augers. Drilling rigs can sample subsurface mineral deposits, test rock, soil and groundwater physical properties, and also can be used to install sub-surface fabrications, such as underground utilities, instrumentation, tunnels or wells. Drilling rigs can be mobile equipment mounted on trucks, tracks or trailers, or more permanent land or marine-based structures. The term "rig" therefore generally refers to the complex equipment that is used to penetrate the surface of the Earth's crust.

<span class="mw-page-title-main">Reciprocating saw</span> Type of machine powered saw

A reciprocating saw is a type of machine-powered saw in which the cutting action is achieved through a push-and-pull ("reciprocating") motion of the blade. The original trade name Sawzall is often used in the United States, where Milwaukee Electric Tool first produced a tool of this type in 1951.

<span class="mw-page-title-main">Chuck (engineering)</span> Clamp used to hold an object with radial symmetry, especially a cylinder

A chuck is a specialized type of clamp used to hold an object with radial symmetry, especially a cylinder. In a drill, a mill and a transmission, a chuck holds the rotating tool; in a lathe, it holds the rotating workpiece.

The shank is the end of a drill bit grasped by the chuck of a drill. The cutting edges of the drill bit contact the workpiece, and are connected via the shaft with the shank, which fits into the chuck. In many cases a general-purpose arrangement is used, such as a bit with cylindrical shaft and shank in a three-jaw chuck which grips a cylindrical shank tightly. Different shank and chuck combination can deliver improved performance, such as allowing higher torque, greater centering accuracy, or moving the bit independently of the chuck, with a hammer action.

<span class="mw-page-title-main">Milwaukee Electric Tool</span> Power tool manufacturer

Milwaukee Electric Tool Corporation, known more commonly as Milwaukee Tool, is a multi-national company that develops, manufactures, and markets power tools, hand tools, tool accessories, tool storage, and personal protective equipment. Milwaukee Tool was last sold in 2005 for $626.6 million to the Hong Kong-based Techtronic Industries, also known as TTI Group. The company is now a subsidiary of TTI Group alongside brands like AEG, Ryobi, Hoover, Dirt Devil, and Vax. In 2022, $206 million was invested in Wisconsin research and development facilities.

<span class="mw-page-title-main">Impact wrench</span> Socket wrench power tool

An impact wrench is a socket wrench power tool designed to deliver high torque output with minimal exertion by the user, by storing energy in a rotating mass, then delivering it suddenly to the output shaft. It was invented by Robert H. Pott of Evansville, Indiana.

<span class="mw-page-title-main">Impact driver</span> Hand tool for loosening threaded fasteners, with a powerful intermittent action

An impact driver is a tool that delivers a strong, sudden rotational force and forward thrust. The force can be delivered either by striking with a hammer in the case of manual impact drivers, or mechanically in the case of powered impact drivers.

<span class="mw-page-title-main">Makita</span> Japanese manufacturer of power tools

Makita Corporation is a Japanese manufacturer of power tools. Founded on March 21, 1915, it is based in Anjō, Japan and operates factories in Brazil, China, Japan, Mexico, Romania, the United Kingdom, Germany, United Arab Emirates, Thailand, Canada, and the United States. Annual sales were equivalent to $3.1 billion in 2012.

<span class="mw-page-title-main">Well</span> Excavation or structure to provide access to groundwater

A well is an excavation or structure created in the ground by digging, driving, or drilling to access liquid resources, usually water. The oldest and most common kind of well is a water well, to access groundwater in underground aquifers. The well water is drawn up by a pump, or using containers, such as buckets or large water bags that are raised mechanically or by hand. Water can also be injected back into the aquifer through the well. Wells were first constructed at least eight thousand years ago and historically vary in construction from a simple scoop in the sediment of a dry watercourse to the qanats of Iran, and the stepwells and sakiehs of India. Placing a lining in the well shaft helps create stability, and linings of wood or wickerwork date back at least as far as the Iron Age.

<span class="mw-page-title-main">Automatic center punch</span>

An automatic center punch is a hand tool used to produce a dimple in a workpiece. It performs the same function as an ordinary center punch but without the need for a hammer. When pressed against the workpiece, it stores energy in a spring, eventually releasing it as an impulse that drives the punch, producing the dimple. The impulse provided to the point of the punch is quite repeatable, allowing for uniform impressions to be made.

<span class="mw-page-title-main">Down-the-hole drill</span> Jackhammer-like tip for drilling deep into rock

A down-the-hole drill, usually called DTH by most professionals, is basically a jackhammer screwed on the bottom of a drill string. The fast hammer action breaks hard rock into small cuttings and dust that are evacuated by a fluid. The DTH hammer is one of the fastest ways to drill hard rock. The system is thought to have been invented independently by Stenuick Frères in Belgium and Ingersoll Rand in the USA in the mid-1950s.

<span class="mw-page-title-main">Rotary hammer</span>

A rotary hammer, also called rotary hammer drill is a power tool that can perform heavy-duty tasks such as drilling and chiseling hard materials. It is similar to a hammer drill in that it also pounds the drill bit in and out while it is spinning. However, rotary hammers use a piston mechanism instead of a special clutch. This causes them to deliver a much more powerful hammer blow, making it possible to drill bigger holes much faster. Most rotary hammers have three settings: drill mode, hammer drill or just hammer, so they can act as a mini jackhammer.

<span class="mw-page-title-main">Ice drilling</span> Method of drilling through ice

Ice drilling allows scientists studying glaciers and ice sheets to gain access to what is beneath the ice, to take measurements along the interior of the ice, and to retrieve samples. Instruments can be placed in the drilled holes to record temperature, pressure, speed, direction of movement, and for other scientific research, such as neutrino detection.

References

  1. ↑ "Definition of percussion drill in English". Oxford Dictionaries . Oxford University Press. Archived from the original on September 8, 2018. Retrieved September 8, 2018.
  2. ↑ "Impact drill". DIY Knowledge. Archived from the original on September 8, 2018. Retrieved September 8, 2018.
  3. ↑ "Cordless Hammer Driver Drill XPH11 Instruction Manual" (PDF). Makita. p. 2. Archived (PDF) from the original on 15 April 2018. Retrieved 15 April 2018. Blows per minute. High (2): 0 - 25,500 /min; Low: 0 - 7,500 /min
  4. ↑ "Drills Drilling Speed Test Results - DIY Gear Reviews". 2023-10-03. Retrieved 2023-10-23.
  5. ↑ Akku Schlagbohrschrauber
  6. ↑ Smil, Vaclav (2006). Transforming the Twentieth Century: Technical Innovations and Their Consequences. Oxford University Press (published April 4, 2006). ISBN   978-0195168754.
  7. ↑ Smil, Vaclav (2010). Why America Is Not a New Rome . The MIT Press. pp.  96. ISBN   978-0262195935.
  8. ↑ Weissenbacher, Manfred (2009). Sources of Power: How Energy Forges Human History by Manfred Weissenbacher. Praeger. p. 362.
  9. ↑ Iron in China
  10. ↑ Han, Gang; Dusseault, Maurice B.; Detournay, Emmanuel; Thomson, Bradley J.; Zacny, Kris (2009). "2". Principles of Drilling and Excavation (PDF). Wiley (published August 31, 2009). p. 60. Archived from the original (PDF) on July 13, 2019.
  11. ↑ "Cable Tool Drilling". Seismic Water Finder.
  12. ↑ Manning, John C. (1996). Applied Principles of Hydrology. Prentice Hall. p. 250. ISBN   978-0135655320.
  13. ↑ "Cable Tool Drilling". Seismic Water Finder.
  14. ↑ "History of Milwaukee". Milwaukee Tool. Retrieved 17 February 2014.
  15. ↑ "Hammer drill hand powered drill working example 70 yrs old!". YouTube .
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.