Infrared Data Association

Last updated
Infrared Data Association
AbbreviationIrDA
Formation1994 [1]
Type Non-profit organisation consisting of multiple special interest groups

The Infrared Data Association (IrDA) is an industry-driven interest group that was founded in 1994 [1] by around 50 companies. IrDA provides specifications for a complete set of protocols for wireless infrared communications, and the name "IrDA" also refers to that set of protocols. The main reason for using the IrDA protocols had been wireless data transfer over the "last one meter" using point-and-shoot principles. Thus, it has been implemented in portable devices such as mobile telephones, laptops, cameras, printers, and medical devices. The main characteristics of this kind of wireless optical communication are physically secure data transfer, line-of-sight (LOS) and very low bit error rate (BER) that makes it very efficient.

Contents

Specifications

IrDA protocol stack Irda protocol stack basic.png
IrDA protocol stack

IrPHY

The mandatory IrPHY (Infrared Physical Layer Specification) is the physical layer of the IrDA specifications. It comprises optical link definitions, modulation, coding, cyclic redundancy check (CRC) and the framer. Different data rates use different modulation/coding schemes:

Further characteristics are:

The frame size depends on the data rate mostly and varies between 64  B and 64 kB. Additionally, bigger blocks of data can be transferred by sending multiple frames consecutively. This can be adjusted with a parameter called "window size" (1–127). Finally, data blocks up to 8 MB can be sent at once. Combined with a low bit error rate of generally <10−9, that communication could be very efficient compared to other wireless solutions.

IrDA transceivers communicate with infrared pulses (samples) in a cone that extends at least 15 degrees half angle off center. The IrDA physical specifications require the lower and upper limits of irradiance such that a signal is visible up to one meter away, but a receiver is not overwhelmed with brightness when a device comes close. In practice, there are some devices on the market that do not reach one meter, while other devices may reach up to several meters. There are also devices that do not tolerate extreme closeness. The typical sweet spot for IrDA communications is from 5 to 60 cm (2.0 to 23.6 in) away from a transceiver, in the center of the cone. IrDA data communications operate in half-duplex mode because while transmitting, a device's receiver is blinded by the light of its own transmitter, and thus full-duplex communication is not feasible. The two devices that communicate simulate full-duplex communication by quickly turning the link around. The primary device controls the timing of the link, but both sides are bound to certain hard constraints and are encouraged to turn the link around as fast as possible.

IrLAP

The mandatory IrLAP (Infrared Link Access Protocol) is the second layer of the IrDA specifications. It lies on top of the IrPHY layer and below the IrLMP layer. It represents the data link layer of the OSI model.

The most important specifications are:

On the IrLAP layer the communicating devices are divided into a "primary device" and one or more "secondary devices". The primary device controls the secondary devices. Only if the primary device requests a secondary device to send, is it allowed to do so.

IrLMP

The mandatory IrLMP (Infrared Link Management Protocol) is the third layer of the IrDA specifications. It can be broken down into two parts. First, the LM-MUX (Link Management Multiplexer), which lies on top of the IrLAP layer. Its most important achievements are:

Second, the LM-IAS (Link Management Information Access Service), which provides a list, where service providers can register their services so other devices can access these services by querying the LM-IAS.

Tiny TP

The optional Tiny TP (Tiny Transport Protocol) lies on top of the IrLMP layer. It provides:

IrCOMM

The optional IrCOMM (Infrared Communications Protocol) lets the infrared device act like either a serial or parallel port. It lies on top of the IrLMP layer.

OBEX

The optional OBEX (Object Exchange) provides the exchange of arbitrary data objects (e.g., vCard, vCalendar or even applications) between infrared devices. It lies on top of the Tiny TP protocol, so Tiny TP is mandatory for OBEX to work.

IrLAN

The optional IrLAN (Infrared Local Area Network) provides the possibility to connect an infrared device to a local area network. There are three possible methods:

As IrLAN lies on top of the Tiny TP protocol, the Tiny TP protocol must be implemented for IrLAN to work.

IrSimple

IrSimple achieves at least four to ten times faster data transmission speeds by improving the efficiency of the infrared IrDA protocol. A 500 KB normal picture from a cell phone can be transferred within one second. [2]

IrSimpleShot

One of the primary targets of IrSimpleShot (IrSS) is to allow the millions of IrDA-enabled camera phones to wirelessly transfer pictures to printers, printer kiosks and flat-panel TVs.

Infrared Financial Messaging

Infrared Financial Messaging (IrFM) is a wireless payment standard developed by the Infrared Data Association. It was thought to be logical because of the excellent privacy of IrDA, which does not pass through walls.

Power meters

Many modern (2021) implementations are used for semi-automated reading of power meters. This high-volume application is keeping IrDA transceivers in production. Lacking specialized electronics, many power meter implementations utilize a bit-banged SIR phy, running at 9600 BAUD using a minimum-width pulse (i.e. 3/16 of a 115.2KBAUD pulse) to save energy. To drive the LED, a computer-controlled pin is turned on and off at the right time. Cross-talk from the LED to the receiving PIN diode is extreme, so the protocol is half-duplex. To receive, an external interrupt bit is started by the start bit, then polled a half-bit time after following bits. A timer interrupt is often used to free the CPU between pulses. Power meters' higher protocol levels abandon IrDA standards, typically using DLMS/COSEM instead. With IrDA transceivers (a package combining an IR LED and PIN diode), even this crude IrDA SIR is extremely resistant to external optical noise from incandescents, sunlight, etc.

Reception

IrDA was popular on PDAs, laptops and some desktops [3] from the late 1990s [4] through the early 2000s. [5] [6] However, it has been displaced by other wireless technologies such as Bluetooth, [7] and Wi-Fi, favored because they don't need a direct line of sight and can therefore support hardware like mice and keyboards. It is still used in some environments where interference makes radio-based wireless technologies unusable.

An attempt was made to revive IrDA around 2005 [8] with IrSimple protocols by providing sub-1-second transfers of pictures between cell phones, printers, and display devices. IrDA hardware was still less expensive and didn't share the same security problems encountered with wireless technologies such as Bluetooth. For example, some Pentax DSLRs (K-x, K-r) incorporated IrSimple for image transfer and gaming. [9]

See also

Related Research Articles

<span class="mw-page-title-main">Bluetooth</span> Short-range wireless technology standard

Bluetooth is a short-range wireless technology standard that is used for exchanging data between fixed and mobile devices over short distances and building personal area networks (PANs). In the most widely used mode, transmission power is limited to 2.5 milliwatts, giving it a very short range of up to 10 metres (33 ft). It employs UHF radio waves in the ISM bands, from 2.402 GHz to 2.48 GHz. It is mainly used as an alternative to wired connections to exchange files between nearby portable devices and connect cell phones and music players with wireless headphones.

<span class="mw-page-title-main">IEEE 802.11</span> Wireless network standard

IEEE 802.11 is part of the IEEE 802 set of local area network (LAN) technical standards, and specifies the set of medium access control (MAC) and physical layer (PHY) protocols for implementing wireless local area network (WLAN) computer communication. The standard and amendments provide the basis for wireless network products using the Wi-Fi brand and are the world's most widely used wireless computer networking standards. IEEE 802.11 is used in most home and office networks to allow laptops, printers, smartphones, and other devices to communicate with each other and access the Internet without connecting wires. IEEE 802.11 is also a basis for vehicle-based communication networks with IEEE 802.11p.

Data communication, including data transmission and data reception, is the transfer of data, transmitted and received over a point-to-point or point-to-multipoint communication channel. Examples of such channels are copper wires, optical fibers, wireless communication using radio spectrum, storage media and computer buses. The data are represented as an electromagnetic signal, such as an electrical voltage, radiowave, microwave, or infrared signal.

<span class="mw-page-title-main">Fast Ethernet</span> Ethernet standards that carry data at the nominal rate of 100 Mbit/s

In computer networking, Fast Ethernet physical layers carry traffic at the nominal rate of 100 Mbit/s. The prior Ethernet speed was 10 Mbit/s. Of the Fast Ethernet physical layers, 100BASE-TX is by far the most common.

In the seven-layer OSI model of computer networking, the physical layer or layer 1 is the first and lowest layer: the layer most closely associated with the physical connection between devices. The physical layer provides an electrical, mechanical, and procedural interface to the transmission medium. The shapes and properties of the electrical connectors, the frequencies to transmit on, the line code to use and similar low-level parameters, are specified by the physical layer.

Zigbee is an IEEE 802.15.4-based specification for a suite of high-level communication protocols used to create personal area networks with small, low-power digital radios, such as for home automation, medical device data collection, and other low-power low-bandwidth needs, designed for small scale projects which need wireless connection. Hence, Zigbee is a low-power, low-data-rate, and close proximity wireless ad hoc network.

<span class="mw-page-title-main">Medium access control</span> Service layer in IEEE 802 network standards

In IEEE 802 LAN/MAN standards, the medium access control (MAC), also called media access control, is the layer that controls the hardware responsible for interaction with the wired or wireless transmission medium. The MAC sublayer and the logical link control (LLC) sublayer together make up the data link layer. The LLC provides flow control and multiplexing for the logical link, while the MAC provides flow control and multiplexing for the transmission medium.

OBEX is a communication protocol that facilitates the exchange of binary objects between devices. It is maintained by the Infrared Data Association but has also been adopted by the Bluetooth Special Interest Group and the SyncML wing of the Open Mobile Alliance (OMA). One of OBEX's earliest popular applications was in the Palm III. This PDA and its many successors use OBEX to exchange business cards, data, even applications.

In telecommunications and computing, bit rate is the number of bits that are conveyed or processed per unit of time.

IEEE 802.15.4 is a technical standard which defines the operation of a low-rate wireless personal area network (LR-WPAN). It specifies the physical layer and media access control for LR-WPANs, and is maintained by the IEEE 802.15 working group, which defined the standard in 2003. It is the basis for the Zigbee, ISA100.11a, WirelessHART, MiWi, 6LoWPAN, Thread, Matter and SNAP specifications, each of which further extends the standard by developing the upper layers which are not defined in IEEE 802.15.4. In particular, 6LoWPAN defines a binding for the IPv6 version of the Internet Protocol (IP) over WPANs, and is itself used by upper layers like Thread.

<span class="mw-page-title-main">Profibus</span> Communications protocol

Profibus is a standard for fieldbus communication in automation technology and was first promoted in 1989 by BMBF and then used by Siemens. It should not be confused with the Profinet standard for Industrial Ethernet. Profibus is openly published as type 3 of IEC 61158/61784-1.

RS-485, also known as TIA-485(-A) or EIA-485, is a standard, originally introduced in 1983, defining the electrical characteristics of drivers and receivers for use in serial communications systems. Electrical signaling is balanced, and multipoint systems are supported. The standard is jointly published by the Telecommunications Industry Association and Electronic Industries Alliance (TIA/EIA). Digital communications networks implementing the standard can be used effectively over long distances and in electrically noisy environments. Multiple receivers may be connected to such a network in a linear, multidrop bus. These characteristics make RS-485 useful in industrial control systems and similar applications.

The media-independent interface (MII) was originally defined as a standard interface to connect a Fast Ethernet medium access control (MAC) block to a PHY chip. The MII is standardized by IEEE 802.3u and connects different types of PHYs to MACs. Being media independent means that different types of PHY devices for connecting to different media can be used without redesigning or replacing the MAC hardware. Thus any MAC may be used with any PHY, independent of the network signal transmission medium.

<span class="mw-page-title-main">Wireless USB</span> Wireless radio communication protocol

Wireless USB (Universal Serial Bus) is a short-range, high-bandwidth wireless radio communication protocol created by the Wireless USB Promoter Group, which is intended to increase the availability of general USB-based technologies. It is unrelated to Wi-Fi and different from the Cypress Wireless USB offerings. It was maintained by the WiMedia Alliance which ceased operations in 2009. Wireless USB is sometimes abbreviated as WUSB, although the USB Implementers Forum discouraged this practice and instead prefers to call the technology Certified Wireless USB to distinguish it from the competing UWB standard.

Autonegotiation is a signaling mechanism and procedure used by Ethernet over twisted pair by which two connected devices choose common transmission parameters, such as speed, duplex mode, and flow control. In this process, the connected devices first share their capabilities regarding these parameters and then choose the highest performance transmission mode they both support.

Consumer IR, consumer infrared, or CIR is a class of devices employing the infrared portion of the electromagnetic spectrum for wireless communications. CIR ports are commonly found in consumer electronics devices such as television remote controls, PDAs, laptops, computers, and video game controllers.

IQRF is a technology for wireless packet-oriented communication via radio frequency (RF) in sub-GHz ISM bands. It is intended for general use where wireless connectivity is needed, either point-to-point or in complex networks, e.g. for telemetry, industrial control, automation of buildings and cities and Internet of Things. Fully open functionality depends solely on a user-specific application.

CAN FD is a data-communication protocol used for broadcasting sensor data and control information on 2 wire interconnections between different parts of electronic instrumentation and control system. This protocol is used in modern high performance vehicles.

References

  1. 1 2 "About IrDA". Archived from the original on 2004-06-10.
  2. ↑ http://irdajp.info/irsimple.html Archived 2013-04-12 at the Wayback Machine IrDA IrSimple Specifications (Infrared Data Association - irda.org)
  3. ↑ "PC Mag". 3 April 2001.
  4. ↑ Beaulieu, Mark (2002). Wireless Internet Applications and Architecture: Building Professional Wireless Applications Worldwide. ISBN   9780201733549.
  5. ↑ "Enterprise PDA phones reviewed". ZDNet .
  6. ↑ "HP iPAQ h6300 Pocket PC review: HP iPAQ h6300 Pocket PC". CNET . Archived from the original on 2023-05-31.
  7. ↑ Lewis, Barry D.; Davis, Peter T. (27 October 2004). Wireless Networks for Dummies. ISBN   9780764579776.
  8. ↑ "Irdajp.info".
  9. ↑ http://www.pentaximaging.com/about-us.aspx?p=press&pid=PENTAXANNOUNCESK-rDIGITALSLRANDNEW35MMLENS20100908174223 Archived 2011-09-27 at the Wayback Machine Pentax K-r

Further reading

Official

Other

This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.