List of specialist Churchill tank variants

Last updated

This is a list of specialist variants of the Churchill tank .

Contents

Churchill Oke

A Churchill Mark II or Mark III with a flamethrower. Developed for the amphibious raid on Dieppe in 1942, the Oke flamethrowing tank was named after its designer, Major J.M. Oke. The design was basically a Churchill tank fitted with the Ronson flamethrower equipment. A tank containing the flame fuel was fitted at the rear, with a pipe from it leading to the fixed angle mounting on the front hull to the left, leaving the hull machine gun unobstructed. Three (named "Boar", "Beetle" and "Bull") were present in the first wave at Dieppe; they were quickly lost, [1] and abandoned.

Assault Vehicle Royal Engineers

Churchill AVRE with fascine on tilt-forward cradle. This particular example is a post-WW2 AVRE on the MK VII chassis. Churchill VII AVRE With Fascine.jpg
Churchill AVRE with fascine on tilt-forward cradle. This particular example is a post-WW2 AVRE on the MK VII chassis.

Proposed by a Canadian engineer as a result of experience from the Dieppe Raid, [2] the Assault Vehicle Royal Engineers (AVRE) was a Churchill Mark III or IV equipped with the "Mortar, Recoiling Spigot, Mark II" (or Petard), a spigot mortar [lower-alpha 1] that throws the 230 mm (9.1 in) [3] 40 lb (18 kg) Bomb Demolition Number 1 ("Flying dustbin") with a 28-pound high-explosive warhead. The Petard, developed by MD1, was designed for the quick levelling of fortifications. The Petard was reloaded by traversing the turret to point front, slightly to the left, with the barrel directly over the co-driver's sliding hatch. The regular two piece co-driver's hatch was plated over, and a small sliding hatch was installed to allow access to the Petard. [4] The Petard barrel would then be 'broken' vertically, and the co-driver would slide open his hatch. The co-driver would then push the projectile into the barrel. [5] The barrel would then be closed, the Petard traversed back down, and the turret rotated back to its original position. [4] The co-driver's hands were briefly exposed during the process.

AVRE 230mm Petard Mortar and its ammunition (projectile standing on its flat nose, with tail facing up, at right) The 29cm Petard spigot mortar on a Churchill AVRE of 79th Squadron, 5th Assault Regiment, Royal Engineers, under command of 3rd Infantry Division, 29 April 1944. A 40lb bomb can be seen on the right. H38001.jpg
AVRE 230mm Petard Mortar and its ammunition (projectile standing on its flat nose, with tail facing up, at right)

The AVRE could also be equipped with numerous other attachments, such as the Small Box Girder bridge, which was carried at the front of the tank and laid across ditches or narrow rivers up to 30 feet wide, and the Canadian Indestructible Roller Device (CIRD), [6] which was used to protect the tracks of a tank from mines. It could also carry fascines, which are large bundles of wood carried on the front of the tank and dropped into trenches to help the Churchill cross over them, devices to place explosive charges against obstacles, and bobbins: massive reels of canvas on drums that were unrolled in front of the Churchill to help it over soft terrain. They were used during the invasion of Normandy to help the Churchill over soft sand, [2] and also served to leave a trackway for following vehicles.

By the time of the invasion of France in June 1944, 180 AVREs had been converted. They were first deployed in Normandy by the 79th Armoured Division on D-Day. [2] They were extremely successful and served until the end of the war. A further 574 followed. [7] While the driver came from the Royal Armoured Corps, the five other crew were drawn from the Royal Engineers. One of the RE crew was a demolitions NCO sapper responsible for priming the "Flying dustbin" and who led the crew when they dismounted from the tank to place demolition charges ("Wade" charges).

Other versions that did not see active service were equipped with anti-mine ploughs, mine rollers, or special demolition charges to destroy reinforced concrete walls. [2]

Post-war, new Churchill AVREs were developed on the basis of a modified Churchill Mk VII armed with a breech-loading low velocity 165mm Royal Ordnance L9 demolition gun that fired a HESH round with about 40 lb (18 kg) of C4 explosive. The name of the AVRE was later changed to "Armoured Vehicle Royal Engineers".

Armoured Recovery Vehicle

Churchill ARV Mk II with front jib erected Tanks and Afvs of the British Army 1939-45 KID2482.jpg
Churchill ARV Mk II with front jib erected

Two marks of armoured recovery vehicle were built from the Churchill

Mk I – A turretless Mk I with a jib that could be fitted at front or rear. Production began in early 1942 [7]

Mk II – A Churchill Mark III or Mark IV with a fixed turret/superstructure with a dummy gun. It was equipped for recovering other tanks from the battlefield. It mounted a front jib with a 7.5 ton capacity, a rear jib rated for 15 ton and a winch that could pull 25 tons. [7] With just a three-man crew, there was enough room to carry the crew of the tank being recovered. Armament was a single Besa machine gun.

Armoured Ramp Carrier

A Churchill tank of the North Irish Horse crossing the Senio in Italy on two stacked Churchill ARKs, April 1945 Churchill ARKs in Italy April 1945 IWM NA 23920.jpg
A Churchill tank of the North Irish Horse crossing the Senio in Italy on two stacked Churchill ARKs, April 1945
Churchill Ark Mk II (UK Pattern) Armoured Ramp Carrier 02.jpg
Churchill Ark Mk II (UK Pattern)

The Armoured Ramp Carrier (ARK) was a turretless Churchill with ramps at either end and trackways along the body to form a mobile bridge. Fifty of these were built on Mark II and Mark IV Churchills. [7] The Link Ark or Twin Ark was two ARKs used side by side to give a wide crossing. The ramps on these were folding types giving a longer, 65 ft (20 m), crossing. [8] The Twin-ARK was used for the post-war Conqueror heavy tank.

Ark Mk II had a wider, 4 ft (1.2 m) instead of the usual 2 ft (0.61 m), trackway on the left side so narrower vehicles could also use the ARK. These were conversions of the Ark Mark I in mid-1944. The "Italian Pattern" Ark Mk II ( initially called "Octopus") was produced in Italy using US ramps on Churchill Mk III chassis and did not have trackways on the tank itself (vehicles drove on the tank's tracks). [9]

"Lakeman Ark" was an experimental design for attacking very high obstacles. It was a turreted Churchill with the trackways built above the height of the turret, and long ramps at the rear. [10]

Bridgelayers

A Churchill bridgelayer of 51st Royal Tank Regiment in action during a demonstration in the Mezzano area, 30 March 1945. The British Army in Italy 1945 NA23553.jpg
A Churchill bridgelayer of 51st Royal Tank Regiment in action during a demonstration in the Mezzano area, 30 March 1945.

The British already had experience of bridge-laying tanks with the Valentine tank and the Covenanter tank, and began work on a Churchill-based bridge-layer in 1942. The bridge ("Bridge, Tank, 30 ft, No.2 "), which could support a tank of 60 tons or be used by Class 40 wheeled traffic, was carried on top of a turretless Mk III or Mk VI chassis. When the obstacle was reached, an arm (driven by hydraulics in the tank) pivoted at the front of the tank and placed the bridge in position. The Churchill Mk VII was used with the No. 3 bridge from 1945 to 1946. [11]

Bridges could also be deployed by the Churchill. "Skid Bailey" was a bridge formed from Bailey bridge parts on skids that was moved into position by one or two Churchill AVREs. Usual use was to bridge cratered roads while under fire.

The "Mobile Bailey Bridge" was a complete bridge suitable for class 40 traffic spanning a 70–80 ft (21–24 m) gap. The bridge itself was 150 ft (46 m) long with 10 ft (3.0 m) ramps at either end. This would be assembled at a safe distance from the gap and then pushed to the site by a Churchill AVRE with another aiding by towing from the front; the middle of the bridge was supported by Orolo unpowered tracked roller units. At the site the AVRE pushed the bridge out over the gap and then disconnected itself. [12] [11]

The "Mobile Brown Bridge" was an improvement on the Mobile Bailey. Named after a Canadian Royal Engineer in Italy, the Bailey bridge was carried on a Churchill which had its turret removed while an AVRE carried and pushed the rear of the bridge. With the first Churchill in position the AVRE would push the bridge out over the gap; an extra 20 ft tail on the bridge acted as a counterweight while the bridge was put in position.

The "Mobile Dalton Bridge", named after an RE officer, was a 140 ft (43 m) long Bailey bridge that was carried on an ARK while a second AVRE pushed. The process was the similar to the Brown Bridge. When the ARK reached the near side of the gap, it stopped and the AVRE pushed the bridge (riding on rollers on the top of the ARK) out over the gap. Once the far end of the bridge was on solid ground the AVRE disengaged and the ARK backed out under the bridge. [11]

Churchill Crocodile

The flame projector on the Churchill Crocodile was in the hull machine gun ball-mount in the hull front plate leaving the main gun unaffected Churchill Crocodile.JPG
The flame projector on the Churchill Crocodile was in the hull machine gun ball-mount in the hull front plate leaving the main gun unaffected

The Churchill Crocodile was a Churchill VII that was converted by replacing the hull machine gun with a flamethrower projector. The fuel, and the compressed gas to drive it, was in an armoured wheeled trailer towed behind. It could fire several one second bursts out to a distance of over 150 yards. The Crocodile was one of "Hobart's Funnies" – another vehicle used by the 79th Armoured Division. A working example can still be seen at the Cobbaton Combat Collection in North Devon.[ citation needed ]

The combination of projector and trailer was produced as a kit that could be fitted to a Churchill; no more than 800 kits were produced. [13] )

Gun Carrier, 3-inch, Mk I, Churchill (A22D)

Churchill Gun Carrier in Dorset, 25 March 1943 The British Army in the United Kingdom 1939-45 H28352.jpg
Churchill Gun Carrier in Dorset, 25 March 1943

Coming out of a General Staff request in 1941 to investigate fitting high velocity large calibre guns on infantry and cruiser tanks specifically for use against German tanks. [14] Of the infantry tanks, neither the Churchill nor Valentine could mount a turret with a high velocity gun larger than the 6-pounder, but it was proposed that a fixed superstructure could carry a larger gun with limited traverse. The QF 3-inch 20 cwt anti-aircraft gun had been replaced by the 3.7-inch gun so these were selected and Vauxhall was provided with 100 guns and given the task of producing the vehicle.

The design used a fixed square thick plate superstructure with the gun in a ball mount low in the front next to the driver. The front was 88 mm (3.5 in), sides 76 mm (3.0 in) with overall weight of 39 tons. Internal stowage included a provision for 12 HE explosive rounds as well as the AP ones. [15]

As an anti-tank gun, the 3-inch gun had a maximum range of 12,000 yards and was a bit more effective than the 57 mm QF 6-pounder at 1,000 yards but less than the 76.2 mm QF 17-pounder under development. [16]

The pilot vehicles were ready for testing in early 1942 and found to be satisfactory. However, in order not to impede production of the Churchill (with the 6-pounder gun) the order was reduced to 24 vehicles. Vauxhall, the main designer and lead manufacturer of the Churchill was already set up for full production of the Gun Carrier with parts and armour ordered and complained with the result that the full order was re-instated before being cut back to 50. [17] [14] The 50 were built between July and November 1942 during which they were the subject of debate about whether they were artillery or tanks. The decision came down in favour of tank, and the Department of Tank Design asked for some changes; by that point in production these could not be incorporated. [17] The prototype was built by Vauxhall and had a T-number, the other 49 by Beyer, Peacock & Company in Manchester, got WD numbers with an S prefix, the same as self-propelled guns. [16] Requirements and tactics had in the meanwhile changed again to focus on the general purpose 75mm gun in the Churchill and a smaller proportion of 17-pounder tanks in use, of which work on the Cruiser Mk VIII Challenger was making progress.

None are known to have been used in combat as the 17-pounder anti-tank gun gave the British the necessary firepower. Some had the gun removed and converted to the "Snake" mine-clearing line charge device and used for trials and training of that in 1942–43. [17] [14]

One unrestored survivor is held at The Tank Museum, it had been used at Lydd Ranges as a target. [18]

Churchill Flail FV3902 or Toad

A 1950s mine-clearing flail tank built on a Churchill chassis using a Rolls-Royce Meteor engine to drive the flails. [19] [20]

Goat

A chargelayer, like the Double Onion device.

Great Eastern Ramp

A much larger, longer and higher trackway ramp than the ARK for crossing 60 ft (18 m). The 25-foot-long front ramps were launched into position with rockets. [10] Ten built and two delivered in 1945 but not used in action. [21]

Kangaroo

A postwar Churchill Kangaroo viewed from the left rear Churchill Kangaroo tank.jpg
A postwar Churchill Kangaroo viewed from the left rear

The Churchill Kangaroo was a turretless Churchill hull converted to an armoured personnel carrier.

Notes

  1. with a spigot mortar the round fits over a solid rod, in this case 29mm diameter, rather than inside a mortar barrel

Related Research Articles

<span class="mw-page-title-main">Tank destroyer</span> Type of armoured fighting vehicle designed to engage and destroy enemy tanks

A tank destroyer, tank hunter or tank killer is a type of armoured fighting vehicle, predominantly intended for anti-tank duties. They are typically armed with a direct fire artillery gun, also known as a self-propelled anti-tank gun, or missile launcher, also called an anti-tank missile carrier. The vehicles are designed specifically to engage and destroy enemy tanks, often with limited operational capacities.

<span class="mw-page-title-main">Military engineering vehicle</span> Battlefield support vehicle

A military engineering vehicle is a vehicle built for construction work or for the transportation of combat engineers on the battlefield. These vehicles may be modified civilian equipment or purpose-built military vehicles. The first appearance of such vehicles coincided with the appearance of the first tanks, these vehicles were modified Mark V tanks for bridging and mine clearance. Modern military engineering vehicles are expected to fulfill numerous roles such as; bulldozer, crane, grader, excavator, dump truck, breaching vehicle, bridging vehicle, military ferry, amphibious crossing vehicle, and combat engineer section carrier.

<span class="mw-page-title-main">Matilda II</span> British Army tank of World War II

The Infantry Tank Mark II, better known as the Matilda, is a British infantry tank of the Second World War.

<span class="mw-page-title-main">Churchill tank</span> British heavy infantry tank

The Tank, Infantry, Mk IV (A22) Churchill was a British infantry tank used in the Second World War, best known for its heavy armour, large longitudinal chassis with all-around tracks with multiple bogies, its ability to climb steep slopes, and its use as the basis of many specialist vehicles. It was one of the heaviest Allied tanks of the war.

<span class="mw-page-title-main">Centurion (tank)</span> British main battle tank

The Centurion was the primary British Army main battle tank of the post-World War II period. Introduced in 1945, it is widely considered to be one of the most successful post-war tank designs, remaining in production into the 1960s, and seeing combat into the 1980s. The chassis was adapted for several other roles, and these variants have remained in service. It was a very popular tank with good armour, mobility, and a powerful main armament.

<span class="mw-page-title-main">Valentine tank</span> British infantry tank

The Tank, Infantry, Mk III, Valentine was an infantry tank produced in the United Kingdom during World War II. More than 8,000 of the type were produced in eleven marks, plus various specialised variants, accounting for approximately a quarter of wartime British tank production. The many variants included riveted and welded construction, petrol and diesel engines and a progressive increase in armament. It was supplied in large numbers to the USSR and built under licence in Canada. It was used extensively by the British in the North African campaign. Developed by Vickers, it proved to be both strong and reliable.

<span class="mw-page-title-main">Cromwell tank</span> British WWII cruiser tank

The Cromwell tank, officially Tank, Cruiser, Mk VIII, Cromwell (A27M), was one of the series of cruiser tanks fielded by Britain in the Second World War. Named after the English Civil War-era military leader Oliver Cromwell, the Cromwell was the first tank put into service by the British to combine high speed from a powerful, reliable engine and reasonable armour. The intended dual-purpose high velocity gun could not be fitted in the turret, so a medium velocity dual purpose gun was fitted instead. Further development of the Cromwell combined with a high velocity gun led to the Comet tank.

<span class="mw-page-title-main">Crusader tank</span> British WWII cruiser tank

Crusader, in full "Tank, Cruiser Mk VI, Crusader", also known by its General Staff number A.15, was one of the primary British cruiser tanks during the early part of the Second World War. Over 5,000 tanks were manufactured and they made important contributions to the British victories during the North African campaign. The Crusader tank would not see active service beyond Africa but the chassis of the tank was modified to create anti-aircraft, fire support, observation, communication, bulldozer and recovery vehicle variants.

<span class="mw-page-title-main">Cruiser Mk I</span> British cruiser tank

The Tank, Cruiser, Mk I (A9) was a British cruiser tank of the interwar period. It was the first cruiser tank: a fast tank designed to bypass the main enemy lines and engage the enemy's lines of communication, as well as enemy tanks. The Cruiser Mk II was a more heavily armoured adaptation of the Mark I, developed at much the same time.

<span class="mw-page-title-main">Cruiser Mk II</span> British cruiser tank

The Tank, Cruiser, Mk II (A10), was a cruiser tank developed alongside the A9 cruiser tank, and was intended to be a heavier, infantry tank version of that type. In practice, it was not deemed suitable for the infantry tank role and was classified as a "heavy cruiser". It served briefly in World War II.

<span class="mw-page-title-main">Cruiser tank</span> Tank

The cruiser tank was a British tank concept of the interwar period for tanks designed as modernised armoured and mechanised cavalry, as distinguished from infantry tanks. Cruiser tanks were developed after medium tank designs of the 1930s failed to satisfy the Royal Armoured Corps. The cruiser tank concept was conceived by Giffard Le Quesne Martel, who preferred many small light tanks to swarm an opponent, instead of a few expensive and unsatisfactory medium tanks. "Light" cruiser tanks carried less armour and were correspondingly faster, whilst "heavy" cruiser tanks had more armour and were slightly slower.

<span class="mw-page-title-main">Infantry tank</span> Tank

The infantry tank was a tank concept developed by the United Kingdom and France in the years leading up to World War II. Infantry tanks were designed to support infantrymen in an attack. To achieve this, the vehicles were generally heavily armoured to allow them to operate in close concert with infantry even under heavy fire. The extra armour came at the expense of speed, which was not an issue when supporting relatively slow-moving foot soldiers.

<span class="mw-page-title-main">Hobart's Funnies</span> Modified tanks first used in the Normandy Landings

Hobart's Funnies is the nickname given to a number of specialist armoured fighting vehicles derived from tanks operated during the Second World War by units of the 79th Armoured Division of the British Army or by specialists from the Royal Engineers.

<span class="mw-page-title-main">Covenanter tank</span> British WWII cruiser tank

The Cruiser tank Mk V or A13 Mk III Covenanter was a British cruiser tank of the Second World War. The Covenanter was the first cruiser tank design to be given a name. Designed by the London, Midland and Scottish Railway as a better-armoured replacement for the Cruiser Mark IV, it was ordered into production in 1939 before pilot models were built. Problems with the design became apparent only after production was under way.

<span class="mw-page-title-main">AEC Armoured Car</span> British heavy armoured car

AEC Armoured Car is the name of a series of British heavy armoured cars built by the Associated Equipment Company (AEC) during the Second World War.

<span class="mw-page-title-main">79th Armoured Division (United Kingdom)</span> Military unit

The 79th Armoured Division was a specialist armoured division of the British Army created during the Second World War. The division was created as part of the preparations for the Normandy invasion on 6 June 1944, D-Day.

<span class="mw-page-title-main">Ram tank</span> Canadian medium tank

The Tank, Cruiser, Ram was a cruiser tank designed and built by Canada in the Second World War, based on the U.S. M3 Medium tank chassis. Due to standardization on the American Sherman tank for frontline units, it was used exclusively for training purposes and was never used in combat as a gun tank. The chassis was used for several other combat roles however, such as a flamethrower tank, observation post and armoured personnel carrier.

<span class="mw-page-title-main">Churchill Crocodile</span> Infantry tank/Flame tank

The Churchill Crocodile was a British flame-throwing tank of late Second World War. It was a variant of the Tank, Infantry, Mk IV (A22) Churchill Mark VII, although the Churchill Mark IV was initially chosen to be the base vehicle.

<span class="mw-page-title-main">Armoured Vehicle Royal Engineers</span> Series of armored military engineering vehicles

Armoured Vehicle Royal Engineers (AVRE), also known as Assault Vehicle Royal Engineers, is the title given to a series of armoured military engineering vehicles operated by the Royal Engineers (RE) for the purpose of protecting engineers during frontline battlefield operations.

<span class="mw-page-title-main">Tanks of New Zealand</span> Use of tanks by the New Zealand Army

The New Zealand Army use of tanks from after the First World War, through the interwar period, the Second World War, the Cold War and to the present day has been limited, but there is some history. The New Zealand armed forces developed in the early twentieth century but served alongside the British and other Empire and Commonwealth nations in World War I and World War II.

References

  1. Perrett p16
  2. 1 2 3 4 "Tank Infantry A22B Churchill Mark III AVRE (E1988.88)". tankmuseum.org. The Tank Museum. Retrieved 5 May 2016.
  3. Armoured Archives. "AVRE 230MM - Fact Checking". YouTube . Archived from the original on 7 July 2022.[ user-generated source ]
  4. 1 2 "Churchill AVRE - Spigot Mortar". armourinfocus.co.uk. Armour in Focus. Retrieved 8 May 2016.
  5. Chamberlain and Ellis p 205
  6. "Churchill AVRE". armourinfocus.co.uk. Armour in Focus. Retrieved 8 May 2016.[ permanent dead link ]
  7. 1 2 3 4 Chamberlain & Ellis (1969) p70
  8. "Assault bridging and equipment". Royal Engineers Museum. Archived from the original on 25 June 2010.
  9. Chamberlain & Ellis (1969) p70-71
  10. 1 2 Chamberlain & Ellis (1969) p73
  11. 1 2 3 AFV Profile 20
  12. Chamberlain & Ellis (1969) p72-73
  13. Delaforce p. 71
  14. 1 2 3 Chamberlain & Ellis, 1969. p68-69
  15. Fletcher 2019 p32-33
  16. 1 2 Fletcher 2019 p32
  17. 1 2 3 White, 1983
  18. Chris Copson (17 February 2024). Evolution of The Churchill Tank | "No Damn Good"?. The Tank Museum. Event occurs at 21:47-22:00, 22:12-22:18. Retrieved 23 February 2024 via Youtube.
  19. Flails for minefield clearance and specifications and acceptance of Churchill Flail (FV 3902), War Office, 1955, WO 32/17394
  20. "The Churchill Toad arrives – to say goodbye". Milweb.
  21. Chris Shillito. "Churchill Great Eastern Ramp". Armourinfocus.co.uk. Retrieved 6 March 2010.