Non ideal compressible fluid dynamics

Last updated
Non-monotone evolution of the Mach number M in the divergent section of a supersonic nozzle. The fluid is siloxane MM (hexamethyldisiloxane,
C
6
H
18
OSi
2
{\displaystyle {\ce {C6H18OSi2}}}
) evolving in the non-ideal gasdynamic regime. Non-ideal nozzle 01.png
Non-monotone evolution of the Mach number M in the divergent section of a supersonic nozzle. The fluid is siloxane MM (hexamethyldisiloxane, ) evolving in the non-ideal gasdynamic regime.

Non ideal compressible fluid dynamics (NICFD), or non ideal gas dynamics, is a branch of fluid mechanics studying the dynamic behavior of fluids not obeying ideal-gas thermodynamics. It is for example the case of dense vapors, supercritical flows and compressible two-phase flows. With the term dense vapors, we indicate all fluids in the gaseous state characterized by thermodynamic conditions close to saturation and the critical point. [1] Supercritical fluids feature instead values of pressure and temperature larger than their critical values, [2] whereas two-phase flows are characterized by the simultaneous presence of both liquid and gas phases. [3]

Contents

In all these cases, the fluid requires to be modelled as a real gas, since its thermodynamic behavior considerably differs from that of an ideal gas, which by contrast appears for dilute thermodynamic conditions. The ideal-gas law can be employed in general as a reasonable approximation of the fluid thermodynamics for low pressures and high temperatures. Otherwise, intermolecular forces and dimension of fluid particles, which are neglected in the ideal-gas approximation, become relevant and can significantly affect the fluid behavior. [4] This is extremely valid for gases made of complex and heavy molecules, which tend to deviate more from the ideal model. [5]

While the fluid dynamics of compressible flows in ideal conditions is well-established and is characterized by several analytical results, [6] when non-ideal thermodynamic conditions are considered, peculiar phenomena possibly occur. This is particularly valid in supersonic conditions, namely for flow velocities larger than the speed of sound in the fluid considered. All typical features of supersonic flows are affected by non-ideal thermodynamics, resulting in both quantitative and qualitative differences with respect to the ideal gas dynamics. [7]

Non-ideal thermodynamics

Compressibility factor Z for different values of reduced pressure and temperature. Compressibility factor generalized diagram.png
Compressibility factor Z for different values of reduced pressure and temperature.

For dilute thermodynamic conditions, the ideal-gas equation of state (EoS) provides sufficiently accurate results in modelling the fluid thermodynamics. This occurs in general for low values of reduced pressure and high values of reduced temperature, where the term reduced refers to the ratio of a certain thermodynamic quantity and its critical value. For some fluids such as air, the assumption of considering ideal conditions is perfectly reasonable and it is widely used. [6]

On the other hand, when thermodynamic conditions approach condensation and the critical point or when high pressures are involved, real-gas models are needed in order to capture the real fluid behavior. In these conditions, in fact, intermolecular forces and compressibility effects come into play. [4]

A measure of the fluid non-ideality is given by the compressibility factor , [8] defined as

where

The compressibility factor is a dimensionless quantity which is equal to 1 for ideal gases and deviates from unity for increasing levels of non-ideality. [9]

Several non-ideal models exist, from the simplest cubic equations of state (such as the Van der Waals [4] [10] and the Peng-Robinson [11] models) up to complex multi-parameter ones, including the Span-Wagner equation of state. [12] [13]

State-of-the-art equations of state are easily accessible through thermodynamic libraries, such as FluidProp or the open-source software CoolProp. [14]

Non-ideal gasdynamic regimes

The dynamic behavior of compressible flows is governed by the dimensionless thermodynamic quantity , which is known as the Landau derivative or fundamental derivative of gas dynamics [15] [16] and is defined as

where

From a mathematical point of view, the Landau derivative is a non-dimensional measure of the curvature of isentropes in the pressure-volume thermodynamic plane. From a physical point of view, the definition of tells that the speed of sound increases with pressure in isentropic transformations for values of , while, by contrast, it decreases with pressure for .

Based on the value of , three gas dynamic regimes can be defined: [16]

Ideal gasdynamic regime

In the ideal regime, the usual ideal-gas behavior is qualitatively recovered. For an ideal gas, in fact, the value of the Landau derivative reduces to the constant value , where is the heat capacity ratio. By definition, is the ratio between the constant pressure and the constant volume specific heats, so it is larger than 1, leading to a value of larger than 1 too. [6]

In this regime, only quantitative differences with respect to the ideal model are encountered. The flow evolution in fact depends on total, or stagnation, thermodynamic conditions. For example, the Mach number evolution of an ideal gas in a supersonic nozzle depends only on the heat capacity ratio (namely on the fluid) and on the exhaust-to-stagnation pressure ratio. [6] Considering real-gas effects, instead, even fixing the fluid and the pressure ratio, different total states yield different Mach profiles. [17]

Typically, for single-phase fluids made of simple molecules, only the ideal gasdynamic regime can be reached, even for thermodynamic conditions very close to saturation. It is for example the case of diatomic or triatomic molecules, such as nitrogen or carbon dioxide, which can only experience small departure from the ideal behavior. [5]

Non-ideal classical gasdynamic regime

Reduced pressure-volume thermodynamic diagram for siloxane fluid MM (hexamethyldisiloxane,
C
6
H
18
OSi
2
{\displaystyle {\ce {C6H18OSi2}}}
), including the liquid-vapor saturation curve, some isentropes and some isolines of the fundamental derivative of gas dynamics
G
{\displaystyle \Gamma }
. The non-ideal gas region (
0
<
G
<
1
{\displaystyle 0<\Gamma <1}
) is shown close to the saturation curve. MM pv plane 03.png
Reduced pressure-volume thermodynamic diagram for siloxane fluid MM (hexamethyldisiloxane, ), including the liquid-vapor saturation curve, some isentropes and some isolines of the fundamental derivative of gas dynamics . The non-ideal gas region () is shown close to the saturation curve.

For fluids with high molecular complexity, state-of-the-art thermodynamic models predict values of in the single-phase region close to the saturation curve, where the speed of sound is largely sensitive to density variations along isentropes. [18] Such fluids belong to different classes of chemical compounds, including hydrocarbons, siloxanes and refrigerants. [5] [18]

In the non-ideal regime, even qualitative differences with respect to ideal gasdynamics can be found, meaning that the flow evolution can be strongly different for varying total conditions. The most peculiar phenomenon of the non-ideal regime is the decrease of the Mach number in isentropic expansions occurring in the supersonic regime, namely processes in which the fluid density decreases. [19] Indeed, for an ideal gas expanding isentropically in a converging-diverging nozzle, the Mach number increases monotonically as the density decreases. [6] By contrast, for flows evolving in the non-ideal regime, a non-monotone Mach number evolution is possible in the divergent section, whereas the density reduction remains monotonic (see figure in the lead section). This particular phenomenon is governed by the quantity , which is a non-dimensional measure of the Mach number derivative with respect to density in isentropic processes: [19]

where

From the definition of , the Mach number increases with density for flow conditions featuring values of . Indeed, this is possible only for values of , that is in the non-ideal regime. However, this is not a sufficient condition for the non-monotone Mach number to appear, since a sufficiently large value of is also required. In particular, supersonic conditions () are necessary. [19]

An analogous effect is encountered in the expansion around rarefactive ramps: for suitable thermodynamic conditions, the Mach number downstream of the ramp can be lower than the one upstream. [20] By contrast, in oblique shock waves, the post-shock Mach number can be larger than the pre-shock one. [21]

Non-classical gas-dynamic regime

Finally, fluids with an even higher molecular complexity can exhibit non-classical behavior in the single-phase vapor region near saturation. They are called Bethe-Zel’dovich-Thompson (BZT) fluids, from the name of physicists Hans Bethe, [22] Yakov Zel'dovich, [23] and Philip Thompson, [24] [25] who first worked on these kinds of fluids.

For thermodynamic conditions lying in the non-classical regime, the non-monotone evolution of the Mach number in isentropic expansions can be found even in subsonic conditions. In fact, for values of , positive values of can be reached also in subsonic flows (). In other words, the non-monotone Mach number evolution is also possible in the convergent section of an isentropic nozzle. [25]

Moreover, a peculiar phenomenon of the non-classical regime is the so-called inverted gas-dynamics. In the classical regime, expansions are smooth isentropic processes, while compressions occur through shock waves, which are discontinuities in the flow. If gas-dynamics is inverted, the opposite occurs, namely rarefaction shock waves are physically admissible and compressions occur through smooth isentropic processes. [24]

As a consequence of the negative value of , two other peculiar phenomena can occur for BZT fluids: shock splitting and composite waves. Shock splitting occurs when an inadmissible pressure discontinuity evolves in time by generating two weaker shock waves. [26] [27] Composite waves, instead, are referred to as phenomena in which two elementary waves propagate as a single entity. [7] [28]

Experimental evidence of a non-classical gas-dynamic regime is not available yet. The main reasons are the complexity of performing experiments in such challenging thermodynamic conditions and the thermal stability of these very complex molecules. [29]

Applications

Compressible flows in non-ideal conditions are encountered in several industrial and aerospace applications. They are employed for example in Organic Rankine Cycles (ORC) [30] and supercritical carbon dioxide (sCO2) systems [31] for power production. In the aerospace field, fluids in conditions close to saturation can be used as oxiders in hybrid rocket motors or for surface cooling of rocket nozzles. [32] Gases made of molecules of high molecular mass can be used in supersonic wind tunnels instead of air to obtain higher Reynolds numbers. [33] Finally, non-ideal flows find application in fuels transportation at high-speed and in Rapid Expansion of Supercritical Solutions (RESS) of CO2 for particles generation or extraction of chemicals. [34]

Organic Rankine cycles

ORC turbogenerator at the LUT University in Lappenranta, Finland. ORC power plant.JPG
ORC turbogenerator at the LUT University in Lappenranta, Finland.

Usual Rankine cycles are thermodynamic cycles that employ water as a working fluid to produce electric power from thermal sources. [36] In Organic Rankine cycles, by contrast, water is substituted by molecularly complex organic compounds. Since the vaporization temperature of these kinds of fluids is lower than that of water at atmospheric pressure, low-to-medium temperature sources can be exploited allowing for heat recovery, for example, from biomass combustion, industrial waste heat, or geothermal heat. [37] For these reasons, ORC technology belongs to the class of renewable energies.

For the design of mechanical components, such as turbines, working in ORC plants, it is fundamental to take into account typical non-ideal gas-dynamic phenomena. In fact, the single-phase vapor at the inlet of an ORC turbine stator usually evolves in the non-ideal thermodynamic region close to the liquid-vapor saturation curve and critical point. Moreover, due to the high molecular mass of the complex organic compounds employed, the speed of sound in these fluids is low compared to that of air and other simple gases. Therefore, turbine stators are very likely to involve supersonic flows even if rather low flow velocities are reached. [38] High supersonic flows can produce large losses and mechanical stresses in the turbine blades due to the occurrence of shock waves, which cause a strong pressure raise. [39] However, when working fluids of the BZT class are employed, expander performances could be improved by exploiting some non-classical phenomena. [40] [41]

Supercritical carbon dioxide cycles

When carbon dioxide is held above its critical pressure (73.773 bar) [42] and temperature (30.9780 °C), [42] it can behave both as a gas and as a liquid, that is it expands to fill entirely its container like a gas but has a density similar to that of a liquid.

Supercritical CO2 is chemically stable, very cheap, and non-flammable, making it suitable as a working fluid for transcritical cycles. [43] For example, it is employed in domestic water heat pumps, which can reach high efficiencies. [43]

Moreover, when used in power generation plants that employ Brayton and Rankine cycles, it can improve efficiency and power output. Its high density enables a strong reduction in turbomachines dimensions, still ensuring the high efficiency of these components. Simpler designs can therefore be adopted, while steam turbines require multiple turbine stages, which necessarily yield larger dimensions and costs. [44]

By contrast, mechanical components within sCO2 Brayton cycles, especially turbomachinery and heat exchangers, suffer from corrosion. [45]

See also

Related Research Articles

<span class="mw-page-title-main">Mach number</span> Ratio of speed of an object moving through fluid and local speed of sound

The Mach number, often only Mach, is a dimensionless quantity in fluid dynamics representing the ratio of flow velocity past a boundary to the local speed of sound. It is named after the Czech physicist and philosopher Ernst Mach.

<span class="mw-page-title-main">Shock wave</span> Propagating disturbance

In physics, a shock wave, or shock, is a type of propagating disturbance that moves faster than the local speed of sound in the medium. Like an ordinary wave, a shock wave carries energy and can propagate through a medium but is characterized by an abrupt, nearly discontinuous, change in pressure, temperature, and density of the medium.

<span class="mw-page-title-main">Compressibility</span> Measure of the relative volume change of a fluid or solid as a response to a pressure change

In thermodynamics and fluid mechanics, the compressibility is a measure of the instantaneous relative volume change of a fluid or solid as a response to a pressure change. In its simple form, the compressibility may be expressed as

Compressible flow is the branch of fluid mechanics that deals with flows having significant changes in fluid density. While all flows are compressible, flows are usually treated as being incompressible when the Mach number is smaller than 0.3. The study of compressible flow is relevant to high-speed aircraft, jet engines, rocket motors, high-speed entry into a planetary atmosphere, gas pipelines, commercial applications such as abrasive blasting, and many other fields.

<span class="mw-page-title-main">Rankine–Hugoniot conditions</span> Concept in physics

The Rankine–Hugoniot conditions, also referred to as Rankine–Hugoniot jump conditions or Rankine–Hugoniot relations, describe the relationship between the states on both sides of a shock wave or a combustion wave in a one-dimensional flow in fluids or a one-dimensional deformation in solids. They are named in recognition of the work carried out by Scottish engineer and physicist William John Macquorn Rankine and French engineer Pierre Henri Hugoniot.

de Laval nozzle Pinched tube generating supersonic flow

A de Laval nozzle is a tube which is pinched in the middle, making a carefully balanced, asymmetric hourglass shape. It is used to accelerate a compressible fluid to supersonic speeds in the axial (thrust) direction, by converting the thermal energy of the flow into kinetic energy. De Laval nozzles are widely used in some types of steam turbines and rocket engine nozzles. It also sees use in supersonic jet engines.

In fluid dynamics, the pressure coefficient is a dimensionless number which describes the relative pressures throughout a flow field. The pressure coefficient is used in aerodynamics and hydrodynamics. Every point in a fluid flow field has its own unique pressure coefficient, Cp.

<span class="mw-page-title-main">Bulk modulus</span> Resistance of a material to uniform pressure

The bulk modulus of a substance is a measure of the resistance of a substance to bulk compression. It is defined as the ratio of the infinitesimal pressure increase to the resulting relative decrease of the volume.

<span class="mw-page-title-main">Heat capacity ratio</span> Thermodynamic quantity

In thermal physics and thermodynamics, the heat capacity ratio, also known as the adiabatic index, the ratio of specific heats, or Laplace's coefficient, is the ratio of the heat capacity at constant pressure to heat capacity at constant volume. It is sometimes also known as the isentropic expansion factor and is denoted by γ (gamma) for an ideal gas or κ (kappa), the isentropic exponent for a real gas. The symbol γ is used by aerospace and chemical engineers.

<span class="mw-page-title-main">Oblique shock</span> Shock wave that is inclined with respect to the incident upstream flow direction

An oblique shock wave is a shock wave that, unlike a normal shock, is inclined with respect to the direction of incoming air. It will occur when a supersonic flow encounters a corner that effectively turns the flow into itself and compresses. The upstream streamlines are uniformly deflected after the shock wave. The most common way to produce an oblique shock wave is to place a wedge into supersonic, compressible flow. Similar to a normal shock wave, the oblique shock wave consists of a very thin region across which nearly discontinuous changes in the thermodynamic properties of a gas occur. While the upstream and downstream flow directions are unchanged across a normal shock, they are different for flow across an oblique shock wave.

Rayleigh flow refers to frictionless, non-adiabatic flow through a constant area duct where the effect of heat addition or rejection is considered. Compressibility effects often come into consideration, although the Rayleigh flow model certainly also applies to incompressible flow. For this model, the duct area remains constant and no mass is added within the duct. Therefore, unlike Fanno flow, the stagnation temperature is a variable. The heat addition causes a decrease in stagnation pressure, which is known as the Rayleigh effect and is critical in the design of combustion systems. Heat addition will cause both supersonic and subsonic Mach numbers to approach Mach 1, resulting in choked flow. Conversely, heat rejection decreases a subsonic Mach number and increases a supersonic Mach number along the duct. It can be shown that for calorically perfect flows the maximum entropy occurs at M = 1. Rayleigh flow is named after John Strutt, 3rd Baron Rayleigh.

Choked flow is a compressible flow effect. The parameter that becomes "choked" or "limited" is the fluid velocity.

<span class="mw-page-title-main">Prandtl–Meyer expansion fan</span> Phenomenon in fluid dynamics

A supersonic expansion fan, technically known as Prandtl–Meyer expansion fan, a two-dimensional simple wave, is a centered expansion process that occurs when a supersonic flow turns around a convex corner. The fan consists of an infinite number of Mach waves, diverging from a sharp corner. When a flow turns around a smooth and circular corner, these waves can be extended backwards to meet at a point.

In fluid dynamics, a moving shock is a shock wave that is travelling through a fluid medium with a velocity relative to the velocity of the fluid already making up the medium. As such, the normal shock relations require modification to calculate the properties before and after the moving shock. A knowledge of moving shocks is important for studying the phenomena surrounding detonation, among other applications.

<span class="mw-page-title-main">Prandtl–Meyer function</span>

In aerodynamics, the Prandtl–Meyer function describes the angle through which a flow turns isentropically from sonic velocity (M=1) to a Mach (M) number greater than 1. The maximum angle through which a sonic flow can be turned around a convex corner is calculated for M = . For an ideal gas, it is expressed as follows,

Fanno flow is the adiabatic flow through a constant area duct where the effect of friction is considered. Compressibility effects often come into consideration, although the Fanno flow model certainly also applies to incompressible flow. For this model, the duct area remains constant, the flow is assumed to be steady and one-dimensional, and no mass is added within the duct. The Fanno flow model is considered an irreversible process due to viscous effects. The viscous friction causes the flow properties to change along the duct. The frictional effect is modeled as a shear stress at the wall acting on the fluid with uniform properties over any cross section of the duct.

Volume viscosity is a material property relevant for characterizing fluid flow. Common symbols are or . It has dimensions, and the corresponding SI unit is the pascal-second (Pa·s).

The Cauchy number (Ca) is a dimensionless number in continuum mechanics used in the study of compressible flows. It is named after the French mathematician Augustin Louis Cauchy. When the compressibility is important the elastic forces must be considered along with inertial forces for dynamic similarity. Thus, the Cauchy Number is defined as the ratio between inertial and the compressibility force in a flow and can be expressed as

Isentropic nozzle flow describes the movement of a gas or fluid through a narrowing opening without an increase or decrease in entropy.

<span class="mw-page-title-main">High pressure jet</span>

A high pressure jet is a stream of pressurized fluid that is released from an environment at a significantly higher pressure than ambient pressure from a nozzle or orifice, due to operational or accidental release. In the field of safety engineering, the release of toxic and flammable gases has been the subject of many R&D studies because of the major risk that they pose to the health and safety of workers, equipment and environment. Intentional or accidental release may occur in an industrial settings like natural gas processing plants, oil refineries and hydrogen storage facilities.

References

  1. Callen, Herbert B. (1985). Thermodynamics and an introduction to thermostatistics (2nd ed.). New York: J. Wiley & Sons. pp. 255–261. ISBN   978-0-471-86256-7.
  2. Schlosky, Kevin M. (1989). "Supercritical phase transitions at very high pressure". Journal of Chemical Education. 66 (12): 989. Bibcode:1989JChEd..66..989S. doi:10.1021/ed066p989. ISSN   0021-9584.
  3. Faghri, Amir; Zhang, Yuwen (2006-01-01), Faghri, Amir; Zhang, Yuwen (eds.), "Two-Phase Flow and Heat Transfer", Transport Phenomena in Multiphase Systems, Boston: Academic Press, pp. 853–949, doi:10.1016/b978-0-12-370610-2.50016-7, ISBN   978-0-12-370610-2, S2CID   98384899 , retrieved 2023-07-06
  4. 1 2 3 Waals, J. D. van der; Rowlinson, John Shipley (1988). On the continuity of the gaseous and liquid states. Studies in statistical mechanics. Amsterdam: North-Holland. ISBN   978-0-444-87077-3.
  5. 1 2 3 Colonna, P.; Guardone, A. (2006). "Molecular interpretation of nonclassical gas dynamics of dense vapors under the van der Waals model". Physics of Fluids. 18 (5): 056101–056101–14. Bibcode:2006PhFl...18e6101C. doi:10.1063/1.2196095. ISSN   1070-6631.
  6. 1 2 3 4 5 Thompson, Philip A. (1972). Compressible-fluid dynamics. Advanced engineering series. New York: McGraw-Hill. pp. 76–99. ISBN   978-0-07-064405-2.
  7. 1 2 Menikoff, Ralph; Plohr, Bradley J. (1989-01-01). "The Riemann problem for fluid flow of real materials". Reviews of Modern Physics. 61 (1): 75–130. Bibcode:1989RvMP...61...75M. doi:10.1103/revmodphys.61.75. ISSN   0034-6861.
  8. Zucker, Robert D.; Biblarz, Oscar (2002). Fundamentals of gas dynamics (2nd ed.). Hoboken, NJ: Wiley. p. 327. ISBN   978-0-471-05967-7.
  9. Thompson, Philip A. (1972). Compressible-fluid dynamics. Advanced engineering series. New York: McGraw-Hill. pp. 99–101. ISBN   978-0-07-064405-2.
  10. Parsegian, V. Adrian (2005). Van der Waals Forces: A Handbook for Biologists, Chemists, Engineers, and Physicists. Cambridge: Cambridge University Press. doi:10.1017/cbo9780511614606. ISBN   978-0-521-83906-8.
  11. Peng, Ding-Yu; Robinson, Donald B. (February 1976). "A New Two-Constant Equation of State". Industrial & Engineering Chemistry Fundamentals. 15 (1): 59–64. doi:10.1021/i160057a011. ISSN   0196-4313. S2CID   98225845.
  12. Span, R.; Wagner, W. (2003-01-01). "Equations of State for Technical Applications. I. Simultaneously Optimized Functional Forms for Nonpolar and Polar Fluids". International Journal of Thermophysics. 24 (1): 1–39. doi:10.1023/A:1022390430888. ISSN   1572-9567. S2CID   116961558.
  13. Span, Roland (2000), "Describing Mixtures with Multiparameter Equations of State", Multiparameter Equations of State, Berlin, Heidelberg: Springer Berlin Heidelberg, pp. 319–340, doi:10.1007/978-3-662-04092-8_8, ISBN   978-3-642-08671-7 , retrieved 2023-07-05
  14. Bell, Ian H.; Wronski, Jorrit; Quoilin, Sylvain; Lemort, Vincent (2014-01-27). "Pure and Pseudo-pure Fluid Thermophysical Property Evaluation and the Open-Source Thermophysical Property Library CoolProp". Industrial & Engineering Chemistry Research. 53 (6): 2498–2508. doi:10.1021/ie4033999. ISSN   0888-5885. PMC   3944605 . PMID   24623957.
  15. 1942, Landau, L.D. "On shock waves" J. Phys. USSR 6 229-230
  16. 1 2 Thompson, Philip A. (1971). "A Fundamental Derivative in Gasdynamics". Physics of Fluids. 14 (9): 1843–1849. Bibcode:1971PhFl...14.1843T. doi:10.1063/1.1693693. ISSN   0031-9171.
  17. Tsien, Hsue-Shen (1946). "One-Dimensional Flows of a Gas Characterized by Vander Waal's Equation of State". Journal of Mathematics and Physics. 25 (1–4): 301–324. doi:10.1002/sapm1946251301. ISSN   0097-1421.
  18. 1 2 Kluwick, Alfred (2004-05-01). "Internal flows of dense gases". Acta Mechanica. 169 (1–4): 123–143. doi:10.1007/s00707-004-0096-z. ISSN   0001-5970. S2CID   121634296.
  19. 1 2 3 Cramer, M. S.; Best, L. M. (1991). "Steady, isentropic flows of dense gases". Physics of Fluids A: Fluid Dynamics. 3 (1): 219–226. Bibcode:1991PhFlA...3..219C. doi:10.1063/1.857855. ISSN   0899-8213.
  20. Cramer, M. S.; Crickenberger, A. B. (1992). "Prandtl-Meyer function for dense gases". AIAA Journal. 30 (2): 561–564. Bibcode:1992AIAAJ..30..561C. doi:10.2514/3.10956. ISSN   0001-1452.
  21. Vimercati, Davide; Gori, Giulio; Guardone, Alberto (2018-05-21). "Non-ideal oblique shock waves". Journal of Fluid Mechanics. 847: 266–285. Bibcode:2018JFM...847..266V. doi:10.1017/jfm.2018.328. hdl: 11311/1063005 . ISSN   0022-1120. S2CID   125447693.
  22. Bethe, H. A. (1998), "On the Theory of Shock Waves for an Arbitrary Equation of State", Classic Papers in Shock Compression Science, New York, NY: Springer New York, pp. 421–495, doi:10.1007/978-1-4612-2218-7_11, ISBN   978-1-4612-7461-2 , retrieved 2023-07-05
  23. "14. On the Possibility of Rarefaction Shock Waves", Selected Works of Yakov Borisovich Zeldovich, Volume I, Princeton University Press, pp. 152–154, 1992-12-31, doi:10.1515/9781400862979.152, ISBN   9781400862979 , retrieved 2023-07-05
  24. 1 2 Thompson, P. A.; Lambrakis, K. C. (1973-08-21). "Negative shock waves". Journal of Fluid Mechanics. 60 (1): 187–208. Bibcode:1973JFM....60..187T. doi:10.1017/s002211207300011x. ISSN   0022-1120. S2CID   123608377.
  25. 1 2 Lambrakis, Konstantine C. (1972). "Existence of Real Fluids with a Negative Fundamental Derivative Γ". Physics of Fluids. 15 (5): 933–935. Bibcode:1972PhFl...15..933L. doi: 10.1063/1.1694004 . ISSN   0031-9171.
  26. Cramer, M. S. (February 1989). "Shock splitting in single-phase gases". Journal of Fluid Mechanics. 199: 281–296. Bibcode:1989JFM...199..281C. doi:10.1017/s0022112089000388. ISSN   0022-1120. S2CID   124690578.
  27. Cramer, M. S. (1991), "Nonclassical Dynamics of Classical Gases", Nonlinear Waves in Real Fluids, Vienna: Springer Vienna, pp. 91–145, doi:10.1007/978-3-7091-2608-0_5, ISBN   978-3-211-82277-7 , retrieved 2023-07-05
  28. KLUWICK, ALFRED (2001), "Rarefaction Shocks", Handbook of Shock Waves, Elsevier, pp. 339–411, doi:10.1016/b978-012086430-0/50008-7, ISBN   9780120864300
  29. Borisov, A. A.; Borisov, Al. A.; Kutateladze, S. S.; Nakoryakov, V. E. (January 1983). "Rarefaction shock wave near the critical liquid–vapour point". Journal of Fluid Mechanics. 126: 59–73. Bibcode:1983JFM...126...59B. doi:10.1017/s002211208300004x. ISSN   0022-1120. S2CID   123399921.
  30. Angelino, G.; Invernizzi, C.; Macchi, E. (1991), "Organic Working Fluid Optimization for Space Power Cycles", Modern Research Topics in Aerospace Propulsion, New York, NY: Springer New York, pp. 297–326, doi:10.1007/978-1-4612-0945-4_16, ISBN   978-1-4612-6956-4 , retrieved 2023-07-05
  31. Feher, E.G. (1968). "The supercritical thermodynamic power cycle". Energy Conversion. 8 (2): 85–90. doi:10.1016/0013-7480(68)90105-8. ISSN   0013-7480.
  32. "Rocket Propulsion Elements. 2nd edition. George P. Sutton. J. Wiley and Sons Inc., New York, 1956. 483 pp. Illustrated. 82s". The Journal of the Royal Aeronautical Society. 61 (559): 503. 1957. doi:10.1017/s0368393100128512. ISSN   0368-3931.
  33. Sagnier, P.; Vérant, J.-L. (1998). "On the validation of high enthalpy wind tunnel simulations". Aerospace Science and Technology. 2 (7): 425–437. doi:10.1016/s1270-9638(99)80002-9. ISSN   1270-9638.
  34. Helfgen, B.; Türk, M.; Schaber, K. (2003). "Hydrodynamic and aerosol modelling of the rapid expansion of supercritical solutions (RESS-process)". The Journal of Supercritical Fluids. 26 (3): 225–242. doi:10.1016/s0896-8446(02)00159-6. ISSN   0896-8446.
  35. Turunen-Saaresti, Teemu; Uusitalo, Antti; Honkatukia, Juha (2017). "Design and testing of high temperature micro-ORC test stand using Siloxane as working fluid". Journal of Physics: Conference Series. 821 (1): 012024. Bibcode:2017JPhCS.821a2024T. doi: 10.1088/1742-6596/821/1/012024 . ISSN   1742-6588. S2CID   114806415.
  36. Saitoh, T.S.; Hoshi, A. (2004). "Proposed solar Rankine cycle system with phase change steam accumulator and CPC solar collector". IECEC '02. 2002 37th Intersociety Energy Conversion Engineering Conference, 2002. IEEE. pp. 725–730. doi:10.1109/iecec.2002.1392137. ISBN   0-7803-7296-4. S2CID   110987716.
  37. Quoilin, Sylvain; Broek, Martijn Van Den; Declaye, Sébastien; Dewallef, Pierre; Lemort, Vincent (2013). "Techno-economic survey of Organic Rankine Cycle (ORC) systems". Renewable and Sustainable Energy Reviews. 22: 168–186. doi: 10.1016/j.rser.2013.01.028 . ISSN   1364-0321.
  38. Brown, Brady; Argrow, Brian (1999-01-11). "Application of Bethe-Zel'dovich-Thompson fluids in organic Rankine cycle engines". 37th Aerospace Sciences Meeting and Exhibit. Reston, Virigina: American Institute of Aeronautics and Astronautics. doi:10.2514/6.1999-462.
  39. Denton, J. D.; Xu, L. (1989-06-04). "The Trailing Edge Loss of Transonic Turbine Blades". Proceedings of the ASME 1989 International Gas Turbine and Aeroengine Congress and Exposition. Volume 1: Turbomachinery. American Society of Mechanical Engineers. doi:10.1115/89-gt-278. ISBN   978-0-7918-7913-9. S2CID   111017969.
  40. Kluwick, A. (1994), "Interacting laminar boundary layers of dense gases", Fluid- and Gasdynamics, Vienna: Springer Vienna, pp. 335–349, doi:10.1007/978-3-7091-9310-5_37, ISBN   978-3-211-82495-5 , retrieved 2023-07-06
  41. CRAMER, M. S.; PARK, S. (1999). "On the suppression of shock-induced separation in Bethe–Zel'dovich–Thompson fluids". Journal of Fluid Mechanics. 393 (1): 1–21. Bibcode:1999JFM...393....1C. doi:10.1017/s0022112099005479. ISSN   0022-1120. S2CID   122254018.
  42. 1 2 Span, Roland; Wagner, Wolfgang (1996-11-01). "A New Equation of State for Carbon Dioxide Covering the Fluid Region from the Triple-Point Temperature to 1100 K at Pressures up to 800 MPa". Journal of Physical and Chemical Reference Data. 25 (6): 1509–1596. doi:10.1063/1.555991. ISSN   0047-2689.
  43. 1 2 Ma, Yitai; Liu, Zhongyan; Tian, Hua (2013). "A review of transcritical carbon dioxide heat pump and refrigeration cycles". Energy. 55: 156–172. doi:10.1016/j.energy.2013.03.030. ISSN   0360-5442.
  44. Fleming, Darryn; Pasch, Jim; Conboy, Thomas; Carlson, Matt (2013-06-03). "Testing Platform and Commercialization Plan for Heat Exchanging Systems for SCO2 Power Cycles". Proceedings of the ASME Turbo Expo 2013: Turbine Technical Conference and Exposition. Volume 8: Supercritical CO2 Power Cycles; Wind Energy; Honors and Awards. American Society of Mechanical Engineers. doi:10.1115/gt2013-95125. ISBN   978-0-7918-5529-4. OSTI   1115493.
  45. Fleming, Darryn; Kruizenga, Alan; Pasch, James; Conboy, Tom; Carlson, Matt (2014-06-16). "Corrosion and Erosion Behavior in Supercritical CO2 Power Cycles". Proceedings of the ASME Turbo Expo 2014: Turbine Technical Conference and Exposition. Volume 3B: Oil and Gas Applications; Organic Rankine Cycle Power Systems; Supercritical CO2 Power Cycles; Wind Energy. doi:10.1115/gt2014-25136. ISBN   978-0-7918-4566-0. OSTI   1221554.

Further reading