Undergrounding

Last updated
A former pylon transformer south of Markgroningen, Germany. Today, the pylon carries only a switch fed by two underground cables. Markgroeningen Pylon Transformer.JPG
A former pylon transformer south of Markgröningen, Germany. Today, the pylon carries only a switch fed by two underground cables.

In civil engineering, undergrounding is the replacement of overhead cables providing electrical power or telecommunications, with underground cables. It helps in wildfire prevention and in making the power lines less susceptible to outages during high winds, thunderstorms or heavy snow or ice storms. An added benefit of undergrounding is the aesthetic quality of the landscape without the powerlines. Undergrounding can increase the capital cost of electric power transmission and distribution but may decrease operating costs over the lifetime of the cables.

Contents

History

Early undergrounding had a basis in the detonation of mining explosives and in undersea telegraph cables. Electric cables were used in Russia to detonate mining explosives in 1812, and to carry telegraph signals across the English Channel in 1850. [1]

With the spread of early electrical power systems, undergrounding began to increase as well. Thomas Edison used underground DC “street pipes” in his early electric power distribution networks; they were insulated first with jute in 1880, and progressed to rubber insulation in 1882. [1]

Subsequent developments occurred in both insulation and fabrication techniques: [1]

During the 20th century direct-buried cable became commonplace.

Comparison

The aerial cables that carry high-voltage electricity and are supported by large pylons are generally considered an unattractive feature of the countryside. Underground cables can transmit power across densely populated areas or areas where land is costly or environmentally or aesthetically sensitive. Underground and underwater crossings may be a practical alternative for crossing rivers.

Advantages

Disadvantages

An underground cable marker. Markers are put at regular intervals to show the route and warn of the hazard of digging into the cable. Bogenbach bei Baerndorf Pfahl1.JPG
An underground cable marker. Markers are put at regular intervals to show the route and warn of the hazard of digging into the cable.

The advantages can in some cases outweigh the disadvantages of the higher investment cost, and more expensive maintenance and management.

Methods

Cables under Broadway in 2013 Utility trench in Bwy @ 42 St jeh.jpg
Cables under Broadway in 2013

Regulations

Europe

The UK regulator Office of Gas and Electricity Markets (OFGEM) permits transmission companies to recoup the cost of some undergrounding in their prices to consumers. The undergrounding must be in National Parks or designated Areas of Outstanding Natural Beauty (AONB) to qualify. In 2021 work started on a project to bury 9 kilometres (5.6 mi) of 400kV overhead power lines running from near Winterbourne Abbas to Friar Waddon ( 50°40′08″N2°30′50″W / 50.669°N 2.514°W / 50.669; -2.514 , north-west of Weymouth) in Dorset AONB. Similar schemes are planned for Snowdonia, the Peak District and the North Wessex Downs. [18]

The most visually intrusive overhead cables of the core transmission network are excluded from the scheme. Some undergrounding projects are funded by the proceeds of national lottery.

All low and medium voltage electrical power (<50 kV) in the Netherlands is now supplied underground.

In Germany, 73% of the medium voltage cables are underground and 87% of low voltage cables are underground. The high percentage of underground cables contributes to the very high grid reliability (SAIDI < 20). [19] In comparison, the SAIDI value (minutes without electricity per year) in the Netherlands is about 30, and in the UK it is about 70.

California

In the United States, the California Public Utilities Commission (CPUC) Rule 20 permits the undergrounding of electrical power cables under certain situations. Rule 20A projects are paid for by all customers of the utility companies. Rule 20B projects are partially funded this way and cover the cost of an equivalent overhead system. Rule 20C projects enable property owners to fund the undergrounding.

Japan

Most electrical power in Japan is still distributed by aerial cables. In Tokyo's 23 wards, according to Japan's Construction and Transport Ministry, just 7.3 percent of cables were laid underground as of March 2008.

Variants

A compromise between undergrounding and using overhead lines is installing air cables. Aerial cables are insulated cables spun between poles and used for power transmission or telecommunication services. An advantage of aerial cables is that their insulation removes the danger of electric shock (unless the cables are damaged). Another advantage is that they forgo the costs—particularly high in rocky areas—of burying. The disadvantages of aerial cables are that they have the same aesthetic issues as standard overhead lines and that they can be affected by storms. However, if the insulation is not destroyed during pylon failure or when hit by a tree, there is no interruption of service. Electrical hazards are minimised and re-hanging the cables may be possible without power interruption.

See also

Related Research Articles

<span class="mw-page-title-main">Insulator (electricity)</span> Material that does not conduct an electric current

An electrical insulator is a material in which electric current does not flow freely. The atoms of the insulator have tightly bound electrons which cannot readily move. Other materials—semiconductors and conductors—conduct electric current more easily. The property that distinguishes an insulator is its resistivity; insulators have higher resistivity than semiconductors or conductors. The most common examples are non-metals.

<span class="mw-page-title-main">Electric power transmission</span> Bulk movement of electrical energy

Electric power transmission is the bulk movement of electrical energy from a generating site, such as a power plant, to an electrical substation. The interconnected lines that facilitate this movement form a transmission network. This is distinct from the local wiring between high-voltage substations and customers, which is typically referred to as electric power distribution. The combined transmission and distribution network is part of electricity delivery, known as the electrical grid.

<span class="mw-page-title-main">High-voltage direct current</span> Electric power transmission system

A high-voltage direct current (HVDC) electric power transmission system uses direct current (DC) for electric power transmission, in contrast with the more common alternating current (AC) transmission systems.

<span class="mw-page-title-main">Electrical substation</span> Part of an electrical transmission, and distribution system

A substation is a part of an electrical generation, transmission, and distribution system. Substations transform voltage from high to low, or the reverse, or perform any of several other important functions. Between the generating station and consumer, electric power may flow through several substations at different voltage levels. A substation may include transformers to change voltage levels between high transmission voltages and lower distribution voltages, or at the interconnection of two different transmission voltages. They are a common component of the infrastructure. There are 55,000 substations in the United States.

<span class="mw-page-title-main">Transmission tower</span> Structure used to support an overhead power line

A transmission tower is a tall structure, usually a lattice tower made of steel that is used to support an overhead power line. In electrical grids, transmission towers carry high-voltage transmission lines that transport bulk electric power from generating stations to electrical substations, from which electricity is delivered to end consumers; moreover, utility poles are used to support lower-voltage sub-transmission and distribution lines that transport electricity from substations to electricity customers.

<span class="mw-page-title-main">Electrical wiring</span> Electrical installation of cabling

Electrical wiring is an electrical installation of cabling and associated devices such as switches, distribution boards, sockets, and light fittings in a structure.

<span class="mw-page-title-main">High voltage</span> Electrical potential which is large enough to cause damage or injury

High voltage electricity refers to electrical potential large enough to cause injury or damage. In certain industries, high voltage refers to voltage above a certain threshold. Equipment and conductors that carry high voltage warrant special safety requirements and procedures.

<span class="mw-page-title-main">Utility pole</span> Post used by public utilities to support overhead wires and related equipment

A utility pole is a column or post, usually made out of wood or aluminum alloy, used to support overhead power lines and various other public utilities, such as electrical cable, fiber optic cable, and related equipment such as transformers and street lights. It can be referred to as a transmission pole, telephone pole, telecommunication pole, power pole, hydro pole, telegraph pole, or telegraph post, depending on its application. A Stobie pole is a multi-purpose pole made of two steel joists held apart by a slab of concrete in the middle, generally found in South Australia.

<span class="mw-page-title-main">Overhead power line</span> Above-ground structure for bulk transfer and distribution of electricity

An overhead power line is a structure used in electric power transmission and distribution to transmit electrical energy along large distances. It consists of one or more conductors suspended by towers or poles. Since the surrounding air provides good cooling, insulation along long passages and allows optical inspection, overhead power lines are generally the lowest-cost method of power transmission for large quantities of electric energy.

<span class="mw-page-title-main">Recloser</span>

In electric power distribution, automatic circuit reclosers (ACRs) are a class of switchgear designed for use on overhead electricity distribution networks to detect and interrupt transient faults. Also known as reclosers or autoreclosers, ACRs are essentially rated circuit breakers with integrated current and voltage sensors and a protection relay, optimized for use as a protection asset. Commercial ACRs are governed by the IEC 62271-111/IEEE Std C37.60 and IEC 62271-200 standards. The three major classes of operating maximum voltage are 15.5 kV, 27 kV and 38 kV.

<span class="mw-page-title-main">Power cable</span> Bundle of wires for transmitting electricity

A power cable is an electrical cable, an assembly of one or more electrical conductors, usually held together with an overall sheath. The assembly is used for transmission of electrical power. Power cables may be installed as permanent wiring within buildings, buried in the ground, run overhead, or exposed. Power cables that are bundled inside thermoplastic sheathing and that are intended to be run inside a building are known as NM-B.

In an electric power system, a fault or fault current is any abnormal electric current. For example, a short circuit is a fault in which a live wire touches a neutral or ground wire. An open-circuit fault occurs if a circuit is interrupted by a failure of a current-carrying wire or a blown fuse or circuit breaker. In three-phase systems, a fault may involve one or more phases and ground, or may occur only between phases. In a "ground fault" or "earth fault", current flows into the earth. The prospective short-circuit current of a predictable fault can be calculated for most situations. In power systems, protective devices can detect fault conditions and operate circuit breakers and other devices to limit the loss of service due to a failure.

An optical ground wire is a type of cable that is used in overhead power lines. Such cable combines the functions of grounding and communications. An OPGW cable contains a tubular structure with one or more optical fibers in it, surrounded by layers of steel and aluminum wire. The OPGW cable is run between the tops of high-voltage electricity pylons. The conductive part of the cable serves to bond adjacent towers to earth ground, and shields the high-voltage conductors from lightning strikes. The optical fibers within the cable can be used for high-speed transmission of data, either for the electrical utility's own purposes of protection and control of the transmission line, for the utility's own voice and data communication, or may be leased or sold to third parties to serve as a high-speed fiber interconnection between cities.

<span class="mw-page-title-main">Stray voltage</span> Electrical potential between unexpected places

Stray voltage is the occurrence of electrical potential between two objects that ideally should not have any voltage difference between them. Small voltages often exist between two grounded objects in separate locations by the normal current flow in the power system. Contact voltage is a better defined term when large voltage appear as a result of a fault. Contact voltage on the enclosure of electrical equipment can appear from a fault in the electrical power system, such as a failure of insulation.

<span class="mw-page-title-main">Aerial cable</span> Electrical infrastructure

An aerial cable or air cable is an insulated cable usually containing all conductors required for an electrical distribution system or a telecommunication line, which is suspended between utility poles or electricity pylons. As aerial cables are completely insulated there is no danger of electric shock when touching them and there is no requirement for mounting them with insulators on pylons and poles. A further advantage is they require less right of way than overhead lines for the same reason. They can be designed as shielded cables for telecommunication purposes. If the cable falls, it may still operate if its insulation is not damaged.

<span class="mw-page-title-main">Pothead</span> High-voltage electrical connection device

A pothead is a type of insulated electrical terminal used for transitioning between overhead line and underground high-voltage cable or for connecting overhead wiring to equipment like transformers. Its name comes from the process of potting or encapsulation of the conductors inside the terminal's insulating bushing.

<span class="mw-page-title-main">Aerial bundled cable</span>

Aerial bundled cables are overhead power lines using several insulated phase conductors bundled tightly together, usually with a bare neutral conductor. This contrasts with the traditional practice of using uninsulated conductors separated by air gaps. This variation of bundled conductors utilizes the same principles as overhead power lines, except that they are closer together to the point of touching but each conductor is surrounded by an insulating layer.

<span class="mw-page-title-main">High-voltage cable</span> Cable used for electric power transmission at high voltage

A high-voltage cable is a cable used for electric power transmission at high voltage. A cable includes a conductor and insulation. Cables are considered to be fully insulated. This means that they have a fully rated insulation system that will consist of insulation, semi-con layers, and a metallic shield. This is in contrast to an overhead line, which may include insulation but not fully rated for operating voltage. High-voltage cables of differing types have a variety of applications in instruments, ignition systems, and alternating current (AC) and direct current (DC) power transmission. In all applications, the insulation of the cable must not deteriorate due to the high-voltage stress, ozone produced by electric discharges in air, or tracking. The cable system must prevent contact of the high-voltage conductor with other objects or persons, and must contain and control leakage current. Cable joints and terminals must be designed to control the high-voltage stress to prevent the breakdown of the insulation.

<span class="mw-page-title-main">Copper conductor</span> Electrical wire or other conductor made of copper

Copper has been used in electrical wiring since the invention of the electromagnet and the telegraph in the 1820s. The invention of the telephone in 1876 created further demand for copper wire as an electrical conductor.

All-dielectric self-supporting (ADSS) cable is a type of optical fiber cable that is strong enough to support itself between structures without using conductive metal elements. It is used by electrical utility companies as a communications medium, installed along existing overhead transmission lines and often sharing the same support structures as the electrical conductors.

References

  1. 1 2 3 "History of underground power cables - IEEE Journals & Magazine". doi:10.1109/MEI.2013.6545260. S2CID   30589908.{{cite journal}}: Cite journal requires |journal= (help)
  2. "How Do Power Lines Cause Wildfires?". Texas Wildfire Mitigation Project. 2014-02-13. Retrieved 2018-05-13.
  3. "Underground power cables".
  4. "To curb power theft, Maharashtra explores underground supply network across state". DNA India. 11 May 2015. Retrieved 20 July 2015.
  5. "No party for thousands of Victoria residents after rogue balloons hit power lines". CBC. Retrieved 7 August 2020.
  6. "Truck snags power line, causes major damage downtown". The Mount Airy News. 22 July 2020. Retrieved 7 August 2020.
  7. Letters to the editors The State(subscription required)
  8. "Urban Forests | American Forests". Archived from the original on 2016-01-18. Retrieved 2016-01-18.
  9. "Edison Electric Institute - Underground Vs. Overhead Distribution Wires: Issues to Consider" (PDF). Retrieved 11 November 2023.
  10. Los Angeles Department of Water & Power System Development Division cost estimate data
  11. Kim, Kim, Cho, Song, Kweon, Chung, Choi, Jae-Han, Ju-Yong, Jin-Tae, Il-Keun, Bo-Min, Il-Yop, Joon-Ho (20 March 2014). "Comparison between Underground Cable and Overhead Line for a Low-Voltage Direct Current Distribution Network Serving Communication Repeater". Energies. 7 (3): 1656–1672. doi: 10.3390/en7031656 .{{cite journal}}: CS1 maint: multiple names: authors list (link)
  12. "Should Power Lines be Underground?" (PDF). Retrieved 11 November 2023.
  13. "Underground vs. Overhead Transmission and Distribution" (PDF). Retrieved 2019-05-09.
  14. "Roadway resurfacing in Boston". 9 July 2018.
  15. Residents of South City neighborhood say digging by utility is leaving bumpy patches on road , retrieved 2022-03-19
  16. "Underground Transmission Lines". Archived from the original on 2021-12-21. Retrieved 2019-05-09.
  17. "NEC 310.60" . Retrieved 2021-11-13.
  18. Boothroyd, John (10 December 2021). "Power for the past". British Archaeology. No. 182. York. pp. 49–50. ISSN   1357-4442.
  19. "Netzausbau in Deutschland" (PDF). kas.de (in German). Retrieved 11 November 2023.