Waypoint

Last updated

A waypoint is an intermediate point or place on a route or line of travel, a stopping point or point at which course is changed, [1] [2] the first use of the term tracing to 1880. [2] In modern terms, it most often refers to coordinates which specify one's position on the globe at the end of each "leg" (stage) of an air flight or sea passage, the generation and checking of which are generally done computationally (with a computer or other programmed device). [1]

Contents

Hence, the term connotes a reference point in physical space, most often associated with navigation, especially in the sea or air—e.g., in the case of sea navigation, a longitudinal and latitudinal coordinate or a GPS point in open water, a location near a known mapped shoal or other entity in a body of water, a point a fixed distance off of a geographical entity such as a lighthouse or harbour entrance, etc.[ citation needed ] When such a point corresponds to an element of physical geography on land, it can be referred to as a landmark.[ citation needed ] In air navigation, waypoints most often consist of a series of abstract GPS points that create artificial airways—"highways in the sky"—created specifically for purposes of air navigation that have no clear connection to features of the real world.

Concept

Waypoints are sets of coordinates that identify a point in physical space. Coordinates used can vary depending on the application. For terrestrial navigation these coordinates can include longitude and latitude. Air navigation also includes altitude. Waypoints have only become widespread for navigational use by the layman since the development of advanced navigational systems, such as the Global Positioning System (GPS) and certain other types of radio navigation. Waypoints located on the surface of the Earth are usually defined in two dimensions (e.g., longitude and latitude); those used in the Earth's atmosphere or in outer space are defined in at least three dimensions (four if time is one of the coordinates, as it might be for some waypoints outside the Earth).

Although the term waypoint has only entered common use in recent years, the equivalent of a waypoint in all but name has existed for as long as human beings have navigated. Waypoints have traditionally been associated with distinctive features of the real world, such as rock formations, springs, oases, mountains, buildings, roadways, waterways, railways, and so on. Today, these associations persist, but waypoints are more often associated with physical artifacts created specifically for navigation, such as radio beacons, buoys, satellites or control points.

In the modern world, waypoints are increasingly abstract, often having no obvious relationship to any distinctive features of the real world. These waypoints are used to help define invisible routing paths for navigation. For example, artificial airways "highways in the sky", created specifically for purposes of air navigation, often have no clear connection to features of the real world, and consist only of a series of abstract waypoints in the sky through which pilots navigate; these airways are designed to facilitate air traffic control and routing of traffic between heavily traveled locations, and do not reference natural terrain features. Abstract waypoints of this kind have been made practical by modern navigation technologies, such as land-based radio beacons and the satellite-based GPS.

Abstract waypoints typically have only specified longitude and latitude or UTM coordinates plus the reference datum, and often a name if they are marked on charts, and are located using a radio navigation system such as a VOR or GPS receiver. A waypoint can be a destination, a fix along a planned course used to make a journey, or simply a point of reference useful for navigation.

Modern applications

With GPS

GPS systems are increasingly used to create and use waypoints in navigation of all kinds. [3] A typical GPS receiver can locate a waypoint with an accuracy of three meters or better when used with land-based assisting technologies such as the Wide Area Augmentation System (WAAS). Waypoints can also be marked on a computer mapping program and uploaded to the GPS receiver, marked on the receiver's own internal map, or entered manually on the device as a pair of coordinates.

If the GPS receiver has track-logging capabilities, one can also define waypoints after the fact from where one has been. For example, marine GPS receivers often have a "man overboard" function, which instantly creates a waypoint in the receiver for the boat's position when enabled and then begins displaying the distance and course back to that position.

In GPS navigation, a "route" is usually defined as a series of two or more waypoints. To follow such a route, the GPS user navigates to the nearest waypoint, then to the next one in turn until the destination is reached. Most receivers have the ability to compute a great circle route towards a waypoint, enabling them to find the shortest route even over long distances, although waypoints are often so closely spaced that this is not a factor.

Many GPS receivers, both military and civilian, now offer integrated cartographic databases (also known as base maps), allowing users to locate a point on a map and define it as a waypoint. Some GPS systems intended for automobile navigation can generate a suggested driving route between two waypoints, based on the cartographic database. As one drives along the route, the system indicates the driver's current location and gives advance notice of upcoming turns. The best of these systems can take into account traffic restrictions such as one-way streets and intersections where left or right turns are prohibited when computing the suggested driving route.

Most GPS receivers allow the user to assign a name to each waypoint. Many models also let the user select a symbol or icon to identify the waypoint on a graphical map display from a built-in library of icons. These include standard map symbols for marine navigation aids such as buoys, marinas and anchorages, as well as land-based landmarks such as churches, bridges, shopping centers, parks and tunnels.

GPS receivers used in air navigation have databases which contain named waypoints, radio navigation aids, airports and heliports. These references comprise the National Airspace System's method of allowing air traffic to select routes that yield efficient point-to-point navigation. Waypoints are often used in the termination phase of a flight to its destination airport. Some GPS receivers are integrated into autopilot or flight management systems, to aid the pilot in control of an aircraft. Waypoints may be found on Aeronautical Charts known as Instrument Flight Rules Enroute Low Altitude Charts, Terminal Arrival Procedures or Sectional Charts.

Without GPS

Although the concept of waypoints has been greatly popularized among non-specialists by the development of the GPS, waypoints can be used with other navigational aids. A notable example is the worldwide use, in orienteering sports, of waypoints with a map that omits a coordinate system, known as control points. [4]

In aerial celestial navigation, waypoints are precomputed along an aircraft's great circle route to divide the flight into rhumb lines and allow celestial fixes to be more rapidly taken using the precomputed intercept method.

In air navigation, waypoints are sometimes defined as intersections between two VOR radials or NDB bearings, or in terms of specific distances and headings towards or away from a radio beacon. For visual air navigation (see the article on visual flight rules), waypoints may be directly associated with distinctive features on the ground that are easily identifiable from aircraft, such as stadiums, power plants, racetracks, etc. Temporary waypoints are sometimes defined as traffic requires, e.g., air-traffic controllers may instruct a pilot to reference a terrain feature at "your ten o'clock position, two miles."

In aviation

In aviation, area navigation (RNAV)—a method of navigation that permits aircraft operation on any desired flight path within the coverage of station-referenced navigation aids or within the limits of the capability of self-contained aids, or a combination of these—relies heavily upon waypoints. RNAV is increasingly used as the primary method of navigation for aircraft.

In the RNAV context, a waypoint is a predetermined geographical position that is defined in terms of latitude/longitude coordinates (altitude is ignored). Waypoints may be a simple named point in space or may be associated with existing navigational aids, intersections, or fixes. A waypoint is most often used to indicate a change in direction, speed, or altitude along the desired path.

Aviation RNAV procedures make use of both fly-over and fly-by waypoints. A fly-over waypoint is a waypoint that must be crossed vertically by an aircraft. A fly-by waypoint is a waypoint that marks the intersection of two straight paths, with the transition from one path to another being made by the aircraft using a precisely calculated turn that "flies by" but does not vertically cross the waypoint.

Waypoints used in aviation are given five-letter names. [5] These names are meant to be pronounceable or have a mnemonic value, so that they may easily be conveyed by voice. In some cases the names correspond to a notable feature or landmark in the area (for example, a waypoint near Newton, Iowa, has the name "MATAG"; Newton was where appliance manufacturer Maytag was founded). [6]

See also

Related Research Articles

<span class="mw-page-title-main">Instrument flight rules</span> Civil aviation regulations for flight on instruments

In aviation, instrument flight rules (IFR) is one of two sets of regulations governing all aspects of civil aviation aircraft operations; the other is visual flight rules (VFR).

<span class="mw-page-title-main">Navigation</span> Process of monitoring and controlling the movement of a craft or vehicle from one place to another

Navigation is a field of study that focuses on the process of monitoring and controlling the movement of a craft or vehicle from one place to another. The field of navigation includes four general categories: land navigation, marine navigation, aeronautic navigation, and space navigation.

The basic principles of air navigation are identical to general navigation, which includes the process of planning, recording, and controlling the movement of a craft from one place to another.

<span class="mw-page-title-main">Non-directional beacon</span> Radio transmitter which emits radio waves in all directions, used as a navigational aid

A non-directional beacon (NDB) or non-directional radio beacon is a radio beacon which does not include inherent directional information. Radio beacons are radio transmitters at a known location, used as an aviation or marine navigational aid. NDB are in contrast to directional radio beacons and other navigational aids, such as low-frequency radio range, VHF omnidirectional range (VOR) and tactical air navigation system (TACAN).

<span class="mw-page-title-main">VHF omnidirectional range</span> Aviation navigation system

Very High Frequency Omnidirectional Range Station (VOR) is a type of short-range radio navigation system for aircraft, enabling aircraft with a receiving unit to determine its position and stay on course by receiving radio signals transmitted by a network of fixed ground radio beacons. It uses frequencies in the very high frequency (VHF) band from 108.00 to 117.95 MHz. Developed in the United States beginning in 1937 and deployed by 1946, VOR became the standard air navigational system in the world, used by both commercial and general aviation, until supplanted by satellite navigation systems such as GPS in the early 21st century. As such, VOR stations are being gradually decommissioned. In 2000 there were about 3,000 VOR stations operating around the world, including 1,033 in the US, but by 2013 the number in the US had been reduced to 967. The United States is decommissioning approximately half of its VOR stations and other legacy navigation aids as part of a move to performance-based navigation, while still retaining a "Minimum Operational Network" of VOR stations as a backup to GPS. In 2015, the UK planned to reduce the number of stations from 44 to 19 by 2020.

Receiver autonomous integrity monitoring (RAIM) is a technology developed to assess the integrity of individual signals collected and integrated by the receiver units employed in a Global Navigation Satellite System (GNSS). The integrity of received signals and resulting correctness and precision of derived receiver location are of special importance in safety-critical GNSS applications, such as in aviation or marine navigation.

<span class="mw-page-title-main">Airway (aviation)</span> Designated route along which aircraft travel between airports

In the United States, airways or air routes are defined by the Federal Aviation Administration (FAA) in two ways:

Inbound aircraft to London Heathrow Airport typically follow one of a number of Standard Arrival Routes (STARs). The STARs each terminate at one of four different RNAV waypoints, and these also define four "stacks" where aircraft can be held, if necessary, until they are cleared to begin their approach to land. Stacks are sections of airspace where inbound aircraft will normally use the pattern closest to their arrival route. They can be visualised as an invisible helix in the sky. Each stack descends in 1,000 feet (305 m) intervals from 16,000 feet (4,877 m) down to 8,000 feet (2,438 m). If these holds become full, aircraft are held at more distant points before being cleared onward to one of the four main holds.

<span class="mw-page-title-main">Flight plan</span> Document filed by a pilot or flight dispatcher indicating the aircrafts flight path

Flight plans are documents filed by a pilot or flight dispatcher with the local Air Navigation Service Provider prior to departure which indicate the plane's planned route or flight path. Flight plan format is specified in ICAO Doc 4444. They generally include basic information such as departure and arrival points, estimated time en route, alternate airports in case of bad weather, type of flight, the pilot's information, number of people on board, and information about the aircraft itself. In most countries, flight plans are required for flights under IFR, but may be optional for flying VFR unless crossing international borders. Flight plans are highly recommended, especially when flying over inhospitable areas such as water, as they provide a way of alerting rescuers if the flight is overdue. In the United States and Canada, when an aircraft is crossing the Air Defense Identification Zone (ADIZ), either an IFR or a special type of VFR flight plan called a DVFR flight plan must be filed. For IFR flights, flight plans are used by air traffic control to initiate tracking and routing services. For VFR flights, their only purpose is to provide needed information should search and rescue operations be required, or for use by air traffic control when flying in a "Special Flight Rules Area."

<span class="mw-page-title-main">Flight planning</span>

Flight planning is the process of producing a flight plan to describe a proposed aircraft flight. It involves two safety-critical aspects: fuel calculation, to ensure that the aircraft can safely reach the destination, and compliance with air traffic control requirements, to minimise the risk of midair collision. In addition, flight planners normally wish to minimise flight cost through the appropriate choice of route, height, and speed, and by loading the minimum necessary fuel on board. Air Traffic Services (ATS) use the completed flight plan for separation of aircraft in air traffic management services, including tracking and finding lost aircraft, during search and rescue (SAR) missions.

<span class="mw-page-title-main">Flight management system</span> Component of aircraft avionics

A flight management system (FMS) is a fundamental component of a modern airliner's avionics. An FMS is a specialized computer system that automates a wide variety of in-flight tasks, reducing the workload on the flight crew to the point that modern civilian aircraft no longer carry flight engineers or navigators. A primary function is in-flight management of the flight plan. Using various sensors (such as GPS and INS often backed up by radio navigation) to determine the aircraft's position, the FMS can guide the aircraft along the flight plan. From the cockpit, the FMS is normally controlled through a Control Display Unit (CDU) which incorporates a small screen and keyboard or touchscreen. The FMS sends the flight plan for display to the Electronic Flight Instrument System (EFIS), Navigation Display (ND), or Multifunction Display (MFD). The FMS can be summarised as being a dual system consisting of the Flight Management Computer (FMC), CDU and a cross talk bus.

In aviation, vertical navigation is glidepath information provided during an instrument approach, independently of ground-based navigation aids in the context of an approach and a form of vertical guidance in the context of climb/descent. An onboard navigation system displays a constant rate descent path to minimums. The VNAV path is computed using aircraft performance, approach constraints, weather data, and aircraft weight. The approach path is computed from the top of descent point to the end of descent waypoint, which is typically the runway or missed approach point.

<span class="mw-page-title-main">Required navigation performance</span> Path selection method for aircraft

Required navigation performance (RNP) is a type of performance-based navigation (PBN) that allows an aircraft to fly a specific path between two 3D-defined points in space.

<span class="mw-page-title-main">North Atlantic Tracks</span> Transatlantic flight routes

The North Atlantic Tracks, officially titled the North Atlantic Organised Track System (NAT-OTS), are a structured set of transatlantic flight routes that stretch from eastern North America to western Europe across the Atlantic Ocean, within the North Atlantic airspace region. They ensure that aircraft are separated over the ocean, where there is little radar coverage. These heavily travelled routes are used by aircraft flying between North America and Europe, operating between the altitudes of 29,000 and 41,000 ft inclusive. Entrance and movement along these tracks is controlled by special oceanic control centres to maintain separation between aircraft. The primary purpose of these routes is to allow air traffic control to effectively separate the aircraft. Because of the volume of NAT traffic, allowing aircraft to choose their own co-ordinates would make the ATC task far more complex. They are aligned in such a way as to minimize any head winds and maximize tail winds impact on the aircraft. This results in much more efficiency by reducing fuel burn and flight time. To make such efficiencies possible, the routes are created twice daily to take account of the shifting of the winds aloft and the principal traffic flow, eastward in North America evening and westward twelve hours later.

<span class="mw-page-title-main">Area navigation</span> Aircraft navigation method

Area navigation is a method of instrument flight rules (IFR) navigation that allows an aircraft to choose any course within a network of navigation beacons, rather than navigate directly to and from the beacons. This can conserve flight distance, reduce congestion, and allow flights into airports without beacons. Area navigation used to be called "random navigation", hence the acronym RNAV.

In aviation, a standard terminal arrival (STAR) is a published flight procedure followed by aircraft on an instrument flight rules (IFR) flight plan just before reaching a destination airport.

An aeronautical chart is a map designed to assist in the navigation of aircraft, much as nautical charts do for watercraft, or a roadmap does for drivers. Using these charts and other tools, pilots are able to determine their position, safe altitude, best route to a destination, navigation aids along the way, alternative landing areas in case of an in-flight emergency, and other useful information such as radio frequencies and airspace boundaries. There are charts for all land masses on Earth, and long-distance charts for trans-oceanic travel.

<span class="mw-page-title-main">Sectional aeronautical chart</span> Type of aeronautical chart

In United States aviation, a sectional aeronautical chart, often called a sectional chart or a sectional for short, is a type of aeronautical chart designed for air navigation under visual flight rules (VFR).

Standard instrument departure (SID) routes, also known as departure procedures (DP), are published flight procedures followed by aircraft on an IFR flight plan immediately after takeoff from an airport.

ICAO performance-based navigation (PBN) specifies that aircraft required navigation performance (RNP) and area navigation (RNAV) systems performance requirements be defined in terms of accuracy, integrity, availability, continuity, and functionality required for the proposed operations in the context of a particular airspace, when supported by the appropriate navigation infrastructure.

References

  1. 1 2 Oxford Staff (January 26, 2017). "Waypoint—Definition… in English". OxfordDictionaries.com. Archived from the original on February 2, 2017. Retrieved January 26, 2017.
  2. 1 2 MW Staff (January 26, 2017). "Definition of Waypoint". Merriam-Webster.com. Archived from the original on February 2, 2017. Retrieved January 26, 2017.
  3. ↑ What is a Waypoint? Archived 2015-02-02 at the Wayback Machine Garmin. Retrieved 11 March 2015.
  4. ↑ "About Orienteering". The Canadian Orienteering Federation. Archived from the original on 2008-10-02. Retrieved 2008-08-11.
  5. ↑ Hofstetter, Isabelle (2022-04-28). Reconnecting the World: 5ANNC Workshop (PDF). Brussels: ICAO. Retrieved 2024-03-22.
  6. ↑ "Instrument Approach Waypoints - Airliners.net". airliners.net. Archived from the original on 4 March 2016. Retrieved 26 January 2017.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.