| 2/180 Gyroplane | |
|---|---|
 | |
| Role | Autogyro |
| National origin | Canada |
| Manufacturer | Avian Aircraft Ltd |
| First flight | 16 February 1961 |
| Number built | 6? |
The Avian 2/180 Gyroplane was a two-seat, single-engine autogyro built in Canada in the 1960s. Several prototypes were built but series production was never achieved.
The Avian Gyroplane was a two-seat autogyro without wings, with a ducted fan pusher propeller driven by a 200 hp (150 kW) Lycoming IO-360 piston engine. It had a three-bladed rotor, formed from bonded aluminium. There were flapping hinges but no drag hinges. [1] In normal flight the rotor was undriven, but the design team were keen to enable vertical jump starts, an autogyro technique which spins up the rotor before take off without forward movement over the ground. The first prototype used conspicuous tip jets fed directly with compressed air from a fuselage-mounted cylinder. [2]
The fuselage was built on a light alloy box beam which carried the cabin, engine mounting, rotor pylon and propeller duct. The well-glazed cabin seated two in tandem in front of the engine. Entry was via a starboard-side door; dual controls were fitted. Yaw was controlled with a rudder mounted within the propeller duct, enhancing its low-speed effectiveness. The Gyroplane had a fixed tricycle undercarriage. The main wheels were mounted on steel cantilever legs and the nosewheel castered. [1]
Avian Aircraft was started by Peter Payne and colleagues from the Avro Canada company specifically to build a modern autogyro. [2]
The Gyroplane prototype first flew in Spring 1960. [1] It was later lost in a crash. The compressed air jump start system was not a success, so the second prototype used the engine, connected via a belt, clutch and gear box. This aircraft was also made lighter than the first with more use of aluminium and fibreglass, increasing cruising speed by 25%. [2] It was followed by three pre-production aircraft. By the end of 1963 more than 300 flying hours were completed. In December 1964 Avian received a $540,000 Canadian government contract to build a modified Gyroplane that would take the type to Certification. This was achieved late in 1968. [1] Full FAA certification was achieved in the 1970s.
In 1970 Avian Ltd went into receivership. Although there were later hopes of a revival, nothing came of them. [3] In 1972 some assets of Avian, including three Gyroplanes, were put up for sale, but no purchase is recorded. However, in 2002 one surviving Gyroplane and its certification rights were sold to Pegasus Rotorcraft Ltd, who renamed it the Pegasus III. [2]
In 2023, ARC Aerosystems [4] acquired the intellectual property, all rights and type certification of the Pegasus, including the one remaining flying example. [5] On 13th November 2023, ARC Aerosystems announced that test flights of the Pegasus will begin in early 2024, at its facilities in Cranfield, with Chris Taylor as the designated test pilot. [6]
ARC have published online plans for three aircraft designs using Pegasus technology. Of these three, only the Pegasus has had prtotypes that are flying and approved for production:
In 2024, ARC announced that they had an order for five Pegasus VTOL, to be delivered in 2026. [7]
Despite being a gyroplane (and not a true helicopter), ARC claims that their aircraft have full VTOL capability.
Data from Jane's All the World's Aircraft 1970-71 [1]
General characteristics
Performance
A flying car or roadable aircraft is a type of vehicle which can function both as a road vehicle and as an aircraft. As used here, this includes vehicles which drive as motorcycles when on the road. The term "flying car" is also sometimes used to include hovercars and/or VTOL personal air vehicles. Many prototypes have been built since the early 20th century, using a variety of flight technologies. Most have been designed to take off and land conventionally using a runway. Although VTOL projects are increasing, none has yet been built in more than a handful of numbers.
A vertical take-off and landing (VTOL) aircraft is one that can take off and land vertically without relying on a runway. This classification can include a variety of types of aircraft including helicopters as well as thrust-vectoring fixed-wing aircraft and other hybrid aircraft with powered rotors such as cyclogyros/cyclocopters and gyrodynes.
An autogyro, or gyroplane, is a class of rotorcraft that uses an unpowered rotor in free autorotation to develop lift. While similar to a helicopter rotor in appearance, the autogyro's unpowered rotor disc must have air flowing upward across it to make it rotate.
In aeronautics, a ducted fan is a thrust-generating mechanical fan or propeller mounted within a cylindrical duct or shroud. Other terms include ducted propeller or shrouded propeller. When used in vertical takeoff and landing (VTOL) applications it is also known as a shrouded rotor.
The CarterCopter is an experimental compound autogyro developed by Carter Aviation Technologies in the United States to demonstrate slowed rotor technology. On 17 June 2005, the CarterCopter became the first rotorcraft to achieve mu-1 (μ=1), an equal ratio of airspeed to rotor tip speed, but crashed on the next flight and has been inoperable since. It is being replaced by the Carter Personal Air Vehicle.
The Bell X-22 is an American V/STOL X-plane with four tilting ducted fans. Takeoff was to selectively occur either with the propellers tilted vertically upwards, or on a short runway with the nacelles tilted forward at approximately 45°. Additionally, the X-22 was to provide more insight into the tactical application of vertical takeoff troop transporters such as the preceding Hiller X-18 and the X-22's successor, the Bell XV-15. Another program requirement was a true airspeed in level flight of at least 525 km/h.
The Curtiss-Wright X-19, company designation Model 200, is an American experimental tiltrotor aircraft of the early 1960s. It was noteworthy for being the last aircraft of any kind manufactured by Curtiss-Wright.
A gyrodyne is a type of VTOL aircraft with a helicopter rotor-like system that is driven by its engine for takeoff and landing only, and includes one or more conventional propeller or jet engines to provide forward thrust during cruising flight. During forward flight the rotor is unpowered and free-spinning, like an autogyro, and lift is provided by a combination of the rotor and conventional wings. The gyrodyne is one of a number of similar concepts which attempt to combine helicopter-like low-speed performance with conventional fixed-wing high-speeds, including tiltrotors and tiltwings.
A rotorcraft or rotary-wing aircraft is a heavier-than-air aircraft with rotary wings or rotor blades, which generate lift by rotating around a vertical mast. Several rotor blades mounted on a single mast are referred to as a rotor. The International Civil Aviation Organization (ICAO) defines a rotorcraft as "supported in flight by the reactions of the air on one or more rotors".
The Fairey Jet Gyrodyne is a British experimental compound gyroplane built by the Fairey Aviation Company that incorporated helicopter, gyrodyne and autogyro characteristics. The Jet Gyrodyne was the subject of a Ministry of Supply (MoS) research contract to gather data for the follow-up design, the Rotodyne.
The Air & Space 18A is a gyroplane that was manufactured in the central United States between 1965 and 2000.
The McCulloch J-2 was a small, two-seat autogyro with an enclosed cabin, one of only three designs of this type of aircraft to receive a type certificate in the United States. It was built by McCulloch Aircraft Corporation.
The Doak VZ-4 was an American prototype Vertical Takeoff and Landing (VTOL) aircraft built in the 1950s for service in the United States Army. Only a single prototype was built, and the U.S. Army withdrew it from active trials in 1963.
The Fairey FB-1 Gyrodyne is an experimental British rotorcraft that used single lifting rotor and a tractor propeller mounted on the tip of the starboard stub wing to provide both propulsion and anti-torque reaction.
The Hafner A.R.III Gyroplane was a British 1930s experimental autogyro designed by Austrian Raoul Hafner, and built by the A.R.III Construction Company at Denham, Buckinghamshire.
Skyworks Aeronautics Corp., formerly Groen Brothers Aviation, Inc., Groen Aeronautics Corporation and Skyworks Global, is an American autogyro research and development company based in Chicago. The company was founded in 1986 by David Groen and his late brother Jay Groen in Salt Lake City, Utah. David Groen remains as Senior Advisor.
The 1933 experimental Pitcairn PA-22 was one of the first wingless autogyros. It was controlled by movement of the rotor plane rather than the usual control surfaces, though initially the much modified lone example retained rudders as a precaution.
The Wilford Gyroplane was based on a German autogyro first flown in 1926. After E. Burke Wilford bought the rights and patents, it was developed in the US until 1936.
ARC Aerosystems is a British consortium that intends to produce modern CAA-certified VTOL autogyros for commercial use. They have a prototype under test, the Pegasus VTOL-Tech, which is to go into production, with delivery expected in 2026. ARC have plans for two other larger gyroplanes, the Linx P3 3-seater, and the Linx P9, a large winged gyroplane.
The Tervamäki ATE-3 is a single-seat autogyro developed in Finland by Jukka Tervamäki and Aulis Eerola in the late 1960s and whose plans were distributed for amateur construction. Other than the designers' own prototype, at least three others were built in Finland and Denmark, The designation stands for Autogyro Tervamäki Eerola, and followed Tervamäki's JT-1 and JT-2 designs. An ATE-3 played a prominent role in a Finnish gangster film of 1969, Leikkikalugangsteri.
