Brush hog

Last updated
Brush hog Brush hog.jpg
Brush hog

A bush hog or "brush hog" is a type of rotary mower. Typically these mowers are designed to be towed behind a farm tractor using the three-point hitch and are driven via the power take-off (PTO). It has blades that are not rigidly attached to the drive like a lawnmower blade, but are on hinges so if the blade hits a rock or stump, it bounces backward and inward, and then centrifugal force makes it go outwards again.

Contents

The rotary blades are not sharpened in the same way as a conventional mower blade. They are usually quite dull so they whack through dense plant growth, whereas a sharp blade often gets stuck or slowed. The blades are very heavy, up to an inch thick, so the centrifugal force pulling out is stronger than the forces of the vegetation bouncing in. They are made of heat treated high carbon steel that can withstand strikes with hard objects such as rocks and stones.

Types of brush hog

Two archetypes of this type of mower are the Bush Hog which is made by Bush Hog, Inc. [1] of Selma, Alabama, and the Flex-Wing by RhinoAg of Gibson City, Illinois. The formal name for this type of implement is a rotary cutter or rotary mower, although it differs from mowers in that it does not cut with a sharp blade, but rather severs with an intentionally very dull wedge-like blade.

Several other manufacturers make these types of mowers including:


There are two types of attachment for a rotary mower, either using the three-point hitch or via a draw bar. The height of the cut on models attached on the three-point hitch is adjusted using the hitch control lever. This adjusts the height of the front of mower. For more radical height adjustment the rear wheel can also be adjusted. Typically the mowers in this category range from 3.3 to 22 feet (1 to 7 m) mowing widths.

A rotary mower that applies chemical while cutting was patented by Tom Burch of Boone, N.C., and was later sold to Diamond Mowers Inc. of Sioux Falls, S.D., under the name Wet Blade .

On draw bar models the height of the cut is determined using hydraulic rams on the mower itself; this requires remote hydraulics on the tractor. These mowers in this category range from 3.3 to 22 feet (1 to 7 m) mowing width. Draw bar mowers which are able to mow larger widths up to 20 feet (6 m) are available. These are multi-spindle and hinged so that the side wings can move over varied terrain. Also these wings can be folded up into a vertical position to reduce width for transport on roadways.

Safety

The blades on a rotary cutter can have top speeds of over 150 miles per hour (240 km/h). Therefore the kinetic energy enables the blades to cut through saplings and small trees up to several inches/centimetres in diameter. Consequently, these mowers can be very dangerous and contact with the blades would cause severe bodily injury or death.

These cutters also pose a thrown object hazard. Objects such as rocks, stones and roadside debris can be thrown in excess of 300 feet (100 m).[ citation needed ]

Sizing

Larger rotary cutters require more powerful tractors to effectively operate. Tractor dealers can recommend the right size brush hog for any of their tractors, or tractor and brush hog sizing charts are available [9] on the Internet. Calculators [10] used to estimate the time required to mow different size areas with different size cutters are also available and can be used to help decide which brush hog is the best investment for different situations.

Related Research Articles

<span class="mw-page-title-main">Tractor</span> Engineering vehicle specifically designed to deliver a high tractive effort

A tractor is an engineering vehicle specifically designed to deliver a high tractive effort at slow speeds, for the purposes of hauling a trailer or machinery such as that used in agriculture, mining or construction. Most commonly, the term is used to describe a farm vehicle that provides the power and traction to mechanize agricultural tasks, especially tillage, and now many more. Agricultural implements may be towed behind or mounted on the tractor, and the tractor may also provide a source of power if the implement is mechanised.

<span class="mw-page-title-main">Combine harvester</span> Machine that harvests grain crops

The modern combine harvester, also called a combine, is a machine designed to harvest a variety of cultivated seeds. Combine harvesters are one of the most economically important labour-saving inventions, significantly reducing the fraction of the population engaged in agriculture. Among the crops harvested with a combine are wheat, rice, oats, rye, barley, corn (maize), sorghum, millet, soybeans, flax (linseed), sunflowers and rapeseed. The separated straw is then either chopped onto the field and ploughed back in, or laid out in rows, ready to be baled and used for bedding and cattle feed.

<span class="mw-page-title-main">Lawn mower</span> Grass cutting device

A lawn mower is a device utilizing one or more revolving blades to cut a grass surface to an even height. The height of the cut grass may be fixed by the design of the mower but generally is adjustable by the operator, typically by a single master lever or by a mechanism on each of the machine's wheels. The blades may be powered by manual force, with wheels mechanically connected to the cutting blades so that the blades spin when the mower is pushed forward, or the machine may have a battery-powered or plug-in electric motor. The most common self-contained power source for lawn mowers is a small 4-stroke internal combustion engine. Smaller mowers often lack any form of self-propulsion, requiring human power to move over a surface; "walk-behind" mowers are self-propelled, requiring a human only to walk behind and guide them. Larger lawn mowers are usually either self-propelled "walk-behind" types or, more often, are "ride-on" mowers that the operator can sit on and control. A robotic lawn mower is designed to operate either entirely on its own or less commonly by an operator on a remote control.

<span class="mw-page-title-main">Mower</span> Mechanical vegetation cutter

A mower is a person or machine that cuts (mows) grass or other plants that grow on the ground. Usually mowing is distinguished from reaping, which uses similar implements, but is the traditional term for harvesting grain crops, e.g. with reapers and combines.

<span class="mw-page-title-main">String trimmer</span> Garden tool for trimming grass or groundcover with a flexible line instead of a blade

A string trimmer, also known by the portmanteau strimmer and the trademarks Weedwacker, Weed Eater and Whipper Snipper, is a garden tool for cutting grass, small weeds, and groundcover. It uses a whirling monofilament line instead of a blade, which protrudes from a rotating spindle at the end of a long shaft topped by a gasoline engine or electric motor.

<span class="mw-page-title-main">Cultivator</span> Farm implement used for secondary tillage

A cultivator is a piece of agricultural equipment used for secondary tillage. One sense of the name refers to frames with teeth that pierce the soil as they are dragged through it linearly. It also refers to machines that use the rotary motion of disks or teeth to accomplish a similar result. The rotary tiller is a principal example.

<span class="mw-page-title-main">Flymo</span> Hover lawnmower brand

Flymo is a hover lawnmower invented by Karl Dahlman in 1964, after seeing Sir Christopher Cockerell's hovercraft. "Flymo" is a brand name of the Swedish company Husqvarna AB, a part of Electrolux from 1978 to 2006. The mower is a variation of the petrol-powered rotary push lawn mower, but uses a fan above the mower's spinning blades to allow the mower's body to hover over the lawn. The mower is claimed to be more manoeuvrable and easier to push than wheeled petrol mowers, while delivering similar results.

<span class="mw-page-title-main">Hedge trimmer</span> Gardening tool

A hedge trimmer, shrub trimmer, or bush trimmer is a gardening tool or machine used for trimming hedges or solitary shrubs (bushes). Different designs as well as manual and powered versions of hedge trimmers exist. Hedge trimmers vary between small hand-held devices to larger trimmers mounted on tractors.

<span class="mw-page-title-main">Trencher (machine)</span> Construction equipment

A trencher is a piece of construction equipment used to dig trenches, especially for laying pipes or electrical cables, for installing drainage, or in preparation for trench warfare. Trenchers may range in size from walk-behind models, to attachments for a skid loader or tractor, to very heavy tracked heavy equipment.

<span class="mw-page-title-main">Claas Cougar</span>

The Claas Cougar is a self-propelled mower produced by the German agricultural machinery manufacturer Claas. The mower, which is named after the cougar, a large American cat, was first presented in 2003. Due to its maximum cutting width of 14 metres (46 ft) it is classified as the largest self-propelled mower in the world.

<span class="mw-page-title-main">Two-wheel tractor</span> Tractor with only one axle

Two-wheel tractor or walking tractor are generic terms understood in the US and in parts of Europe to represent a single-axle tractor, which is a tractor with one axle, self-powered and self-propelled, which can pull and power various farm implements such as a trailer, cultivator or harrow, a plough, or various seeders and harvesters. The operator usually walks behind it or rides the implement being towed. Similar terms are mistakenly applied to the household rotary tiller or power tiller; although these may be wheeled and/or self-propelled, they are not tailored for towing implements. A two-wheeled tractor specializes in pulling any of numerous types of implements, whereas rotary tillers specialize in soil tillage with their dedicated digging tools. This article concerns two-wheeled tractors as distinguished from such tillers.

<span class="mw-page-title-main">Flail mower</span> Powered vegetation cutter

A flail mower is a type of powered garden/agricultural equipment which is used to deal with heavier grass/scrub which a normal lawn mower could not cope with. Some smaller models are self-powered, but many are PTO driven implements, which can attach to the three-point hitches found on the rear of most tractors. This type of mower is best used to provide a rough cut to long grass and even brambles in locations such as roadsides, where contact with loose debris may be possible.

Ceramic tile cutters are used to cut ceramic tiles to a required size or shape. They come in a number of different forms, from basic manual devices to complex attachments for power tools.

<span class="mw-page-title-main">Swathe</span>

A swathe is the strip of cut crop made by a scythe or a mowing-machine. A mower with a scythe cuts a swathe along the mowing-edge leaving the uncut grass to the right and the cut grass laid in a windrow to the left on the previously mown land. The swathe width depends on the blade length, the nature of the crop, and the mower, but for grass is usually about 1.5 metres (4.9 ft) wide. When mowing in a team the mowers start at the edge of a meadow in a staggered line, then proceed clockwise, leaving a series of swathes with windrows and finishing in the middle.

Roths Industries, Inc. (1945–1960) was a manufacturer of small garden tractors and other agricultural equipment founded by Herbert C. Roths in Alma, Michigan. The company manufactured Garden King Walking Tractors, BesRo Riding Tractors, and Till Ro Stalk Cutters.

<span class="mw-page-title-main">Rotary mower</span> Powered vegetation cutter

A rotary mower is a unit of powered machinery that uses a rotating blade or blades to cut vegetation.

<span class="mw-page-title-main">Atco (British mower company)</span>

Atco (Atlas Chain Company) Limited was a British mower company which traded as "Atco Ltd" from 1981 to 1990, making lawn mowers and garden tools. It sold a range of lawn mowers including lawn and garden tractors.

Mower blades are the cutting components of lawn mowers. They are usually made of sturdy metals as they must be able to withstand high-speed contact with a variety of objects in addition to grass. The materials used vary by manufacturer.

<span class="mw-page-title-main">Brushcutter (garden tool)</span> Powered garden tool

A brushcutter is a powered garden or agricultural tool used to trim weeds, small trees, and other foliage not accessible by a lawn mower or rotary mower. Various blades or trimmer heads can be attached to the machine for specific applications.

<span class="mw-page-title-main">Hayter (lawn mowers)</span>

Hayter is a British high-end manufacturer and distributor of garden machinery, specialising in industrial and domestic lawn mowers. The company's headquarters are located in Spellbrook, Hertfordshire, where it was founded in 1946 by Douglas Hayter, a pioneer of the rotary mower. The company was awarded a Royal Warrant in 1960.

References

  1. "Home". Bush Hog. Retrieved 2024-02-16.
  2. "The Bush-Whacker web site".
  3. "DR Power Equipment".
  4. "Hardee By EVH".
  5. "King Kutter".
  6. "Land Pride".
  7. "inventor of the Flex-Wing".
  8. "Woods Equipment – Top-quality attachments and replacement parts for the agricultural, grounds maintenance and construction markets". 2024-02-01. Retrieved 2024-02-16.
  9. Tractor and brush hog sizing chart, tractordata.com
  10. Brush hog mowing calculator, tractordata.com