 |
The Buell dryer, also known as the "turbo shelf" dryer, is an indirectly-heated industrial dryer once widely used in the Cornwall and Devon china clay mining industry. The Buell dryer was introduced to the china clay industry by English Clays Lovering Pochin & Co. Ltd for their china clay drying plants in Cornwall and Devon, as part of the mechanization and modernization of the industry, which up to that point had been using the same primitive processing methods for almost 100 years.
The industry's first attempt to mechanize its drying process, an oil-fired rotary dryer installed at Rockhill near Stenalees in 1939, had been halted before it could be commissioned by the outbreak of war, with the Board of Trade exercising its wartime powers to place restrictions on the industry, rationing in particular the use of oil and steel. To circumvent these restrictions, in 1944 a Buell dryer was purchased second hand from a fluorspar mine in Derbyshire, and was installed in an existing building at ECLP's Drinnick site in Nanpean, heated by exhaust steam from Drinnick power plant. As such, it became the first operating mechanical dryer in the Cornish china clay industry, despite not being the first to be constructed.
A 1948 Board Of Trade Working Party report into the China Clay industry concluded that restrictions on the industry should be relaxed to allow mechanization to begin. The 1948 report led to Parliament ordering an end to Board Of Trade restrictions on the china clay industry, leading to a period of rapid mechanization.
In the 25 years that followed, additional Buell dryers were constructed at Kernick, Drinnick, Rocks, Blackpool near Burngullow, Marsh Mills, Parkandillack, Par Harbour, and Goonvean & Rostowrack Ltd's Trelavour site. The Drinnick dryer site was also expanded to include several more steam-heated dryers.
The dryer itself is composed of a large upright cylindrical chamber, inside of which are 25 to 30 layers of trays or "hearths". Indirectly-heated air from an oil-fired (latterly natural gas-fired) furnace or steam heater is distributed throughout the dryer by a series of fans and ducts. At the center of the dryer is a rotating column, to which the trays are attached and positioned radially within the dryer. Material enters the top of the dryer and lands on one of the top trays. As the central column rotates, fixed arms push the material off the tray, dropping it down onto the one below it. Gradually the material works its way down through the dryer in this manner, and after 45 minutes, clay exits the bottom of the dryer onto conveyor belts.
The material to be dried usually enters the top of the dryer with a moisture content of around 18%, and exit at around 8-10%. Generally, these figures all depend on the dewatering processes employed before the material reaches the dryer. Commonly, the Buell dryer handled shredded filter press cakes from standard square plate filter presses, although these were later replaced by a circular-plate filter press capable of operating at much higher pressure. After being shredded, these press cakes were brought by conveyor belt to a paddle mixer in which the cakes were back-mixed with dried clay. The back-mixed clay could then either be extruded into pellets and fed directly to the dryer or, depending on the grade of clay to be produced, might go through an additional stage of pug milling.
Dry cleaning is any cleaning process for clothing and textiles using a solvent other than water.
A clothes dryer, also known as tumble dryer, is a powered household appliance that is used to remove moisture from a load of clothing, bedding and other textiles, usually after they are washed in a washing machine.
A paper machine is an industrial machine which is used in the pulp and paper industry to create paper in large quantities at high speed. Modern paper-making machines are based on the principles of the Fourdrinier Machine, which uses a moving woven mesh to create a continuous paper web by filtering out the fibres held in a paper stock and producing a continuously moving wet mat of fibre. This is dried in the machine to produce a strong paper web.
Bulk material handling is an engineering field that is centered on the design of equipment used for the handling of dry materials. Bulk materials are those dry materials which are powdery, granular or lumpy in nature, and are stored in heaps. Examples of bulk materials are minerals, ores, coal, cereals, woodchips, sand, gravel, clay, cement, ash, salt, chemicals, grain, sugar, flour and stone in loose bulk form. It can also relate to the handling of mixed wastes. Bulk material handling is an essential part of all industries that process bulk ingredients, including: food, beverage, confectionery, pet food, animal feed, tobacco, chemical, agricultural, polymer, plastic, rubber, ceramic, electronics, metals, minerals, paint, paper, textiles and more.
A car wash, or auto wash, is a facility used to clean the exterior, and in some cases the interior, of cars. Car washes can be self-service, full-service, or fully automated. Car washes may also be events where people pay to have their cars washed by volunteers, often using less specialized equipment, as a fundraiser.
A platen is a platform with a variety of roles in printing or manufacturing. It can be a flat metal plate pressed against a medium to cause an impression in letterpress printing. Platen may also refer to a typewriter roller which friction-feeds paper into position below the typebars or print head. It can refer to the glass surface of a copier, and the rotating disk used to polish semiconductor wafers.
The following outline is provided as an overview of and topical guide to the preparation of food:
A rotary dryer is a type of industrial dryer used to reduce or minimize the moisture content of the material it is handling by bringing it into contact with a heated gas. The dryer is made up of a rotating cylinder, a drive mechanism, and a support structure. The cylinder is inclined slightly with the discharge end is lower than the material feed end so that material moves through the dryer under the influence of gravity. Material to be dried enters the dryer and, as the dryer rotates, the material is lifted up by a series of fins lining the inner wall of the dryer. When the material gets high enough, it falls back down to the bottom of the dryer, passing through the hot gas stream as it falls.
Fish meal, sometimes spelt fishmeal, is a commercial product made from whole wild-caught fish, bycatch, and fish by-products to feed farm animals, e.g., pigs, poultry, and farmed fish. Because it is calorically dense and cheap to produce, fishmeal has played a critical role in the growth of factory farms and the number of farm animals it is possible to breed and feed.
Agitated Nutsche filter (ANF) is a filtration technique used in applications such as dye, paint, and pharmaceutical production and waste water treatment. Safety requirements and environmental concerns due to solvent evaporation led to the development of this type of filter wherein filtration under vacuum or pressure can be carried out in closed vessels and solids can be discharged straightaway into a dryer.
For environmental remediation, Low-temperature thermal desorption (LTTD), also known as low-temperature thermal volatilization, thermal stripping, and soil roasting, is an ex-situ remedial technology that uses heat to physically separate petroleum hydrocarbons from excavated soils. Thermal desorbers are designed to heat soils to temperatures sufficient to cause constituents to volatilize and desorb from the soil. Although they are not designed to decompose organic constituents, thermal desorbers can, depending upon the specific organics present and the temperature of the desorber system, cause some organic constituents to completely or partially decompose. The vaporized hydrocarbons are generally treated in a secondary treatment unit prior to discharge to the atmosphere. Afterburners and oxidizers destroy the organic constituents. Condensers and carbon adsorption units trap organic compounds for subsequent treatment or disposal.
English China Clays PLC, or ECC, was a mining company involved in the extraction of china clay, based in St Austell, Cornwall. It was once a constituent of the FTSE 100 Index but in 1999 was acquired by Imetal.
An industrial filter press is a tool used in separation processes, specifically to separate solids and liquids. The machine stacks many filter elements and allows the filter to be easily opened to remove the filtered solids, and allows easy cleaning or replacement of the filter media.
The belt filter is an industrial machine, used for solid/liquid separation processes, particularly the dewatering of sludges in the chemical industry, mining and water treatment. Belt filter presses are also used in the production of apple juice, cider and winemaking. The process of filtration is primarily obtained by passing a pair of filtering cloths and belts through a system of rollers. The system takes a sludge or slurry as a feed, and separates it into a filtrate and a solid cake.
A belt dryer a kind of industrial dryer, is an apparatus which is used for continuous drying and cooling of woodchip, pellets, pastes, moulded compounds and panels using air, inert gas, or flue gas.
The Wheal Martyn China Clay Museum is a museum of china clay mining, at Carthew, on the B3274 road about 2 miles (3.2 km) north of St Austell in Cornwall, England. A Victorian clay works has been preserved, and there is an exhibition building.
A dewatering screw press is a screw press that separates liquids from solids. A screw press can be used in place of a belt press, centrifuge, or filter paper. It is a simple, slow moving device that accomplishes dewatering by continuous gravitational drainage. Screw presses are often used for materials that are difficult to press, for example those that tend to pack together. The screw press squeezes the material against a screen or filter and the liquid is collected through the screen for collection and use.
A filter drier is a piece of process equipment used during the filtration and drying phase of a pharmaceutical, bio pharmaceutical or chemical process for an active pharmaceutical ingredient (API) or other compounds production. Filter dryers are designed for washing and isolating solids with or without integrated containment systems.
A centrifuge is a device that employs a high rotational speed to separate components of different densities. This becomes relevant in the majority of industrial jobs where solids, liquids and gases are merged into a single mixture and the separation of these different phases is necessary. A decanter centrifuge separates continuously solid materials from liquids in the slurry, and therefore plays an important role in the wastewater treatment, chemical, oil, and food processing industries. There are several factors that affect the performance of a decanter centrifuge, and some design heuristics are to be followed which are dependent upon given applications.
Pasta processing is the process in which wheat semolina or flour is mixed with water and the dough is extruded to a specific shape, dried and packaged.