Convergence (routing)

Last updated

Convergence is the state of a set of routers that have the same topological information about the internetwork in which they operate. For a set of routers to have converged, they must have collected all available topology information from each other via the implemented routing protocol, the information they gathered must not contradict any other router's topology information in the set, and it must reflect the real state of the network. In other words: in a converged network all routers "agree" on what the network topology looks like. [1]

Contents

Convergence is an important notion for a set of routers that engage in dynamic routing. All interior gateway protocols rely on convergence to function properly. "To have, or be, converged" is the normal state of an operational autonomous system. The Exterior Gateway Routing Protocol BGP typically never converges because the Internet is too big for changes to be communicated fast enough.

Convergence process

When a routing protocol process is enabled, every participating router will attempt to exchange information about the topology of the network. The extent of this information exchange, the way it is sent and received, and the type of information required vary widely depending on the routing protocol in use, see e.g. RIP, OSPF, BGP4.

A state of convergence is achieved once all routing protocol-specific information has been distributed to all routers participating in the routing protocol process. Any change in the network that affects routing tables will break the convergence temporarily until this change has been successfully communicated to all other routers.

Convergence time

Convergence time is a measure of how fast a group of routers reach the state of convergence. It is one of the main design goals and an important performance indicator for routing protocols, which should implement a mechanism that allows all routers running the protocol to quickly and reliably converge. [2] Of course, the size of the network also plays an important role. A larger network will converge more slowly than a smaller one.

RIP is a routing protocol that converges so slowly that even a network of a few routers can take a couple of minutes to converge. In case of a new route being advertised, triggered updates can speed up RIP's convergence but to flush a route that previously existed takes longer due to the holddown timers in use. OSPF is an example of a fast-converging routing protocol. A network of a few OSPF routers can converge in a matter of seconds. [3]

Certain configuration and hardware conditions will prevent a network from ever converging. For instance, a "flapping" interface (an interface that frequently changes its state between "up" and "down") might cause conflicting information to propagate throughout the network so the routers never agree on its current state. Under certain circumstances it might be desirable to withhold detailed routing information from parts of the network via route aggregation, thereby speeding up convergence of the topological information shared by all routers.

See also

Related Research Articles

Internetwork Packet Exchange (IPX) is the network-layer protocol in the IPX/SPX protocol suite. IPX is derived from Xerox Network Systems' IDP. It also has the ability to act as a transport layer protocol.

<span class="mw-page-title-main">Border Gateway Protocol</span> Protocol for communicating routing information on the Internet

Border Gateway Protocol (BGP) is a standardized exterior gateway protocol designed to exchange routing and reachability information among autonomous systems (AS) on the Internet. BGP is classified as a path-vector routing protocol, and it makes routing decisions based on paths, network policies, or rule-sets configured by a network administrator.

Intermediate System to Intermediate System is a routing protocol designed to move information efficiently within a computer network, a group of physically connected computers or similar devices. It accomplishes this by determining the best route for data through a packet switching network.

Open Shortest Path First (OSPF) is a routing protocol for Internet Protocol (IP) networks. It uses a link state routing (LSR) algorithm and falls into the group of interior gateway protocols (IGPs), operating within a single autonomous system (AS).

The Routing Information Protocol (RIP) is one of the oldest distance-vector routing protocols which employs the hop count as a routing metric. RIP prevents routing loops by implementing a limit on the number of hops allowed in a path from source to destination. The largest number of hops allowed for RIP is 15, which limits the size of networks that RIP can support.

In computer networking and telecommunications, route flapping occurs when a router alternately advertises a destination network via one route then another, or as unavailable and then available again, in quick sequence.

Enhanced Interior Gateway Routing Protocol (EIGRP) is an advanced distance-vector routing protocol that is used on a computer network for automating routing decisions and configuration. The protocol was designed by Cisco Systems as a proprietary protocol, available only on Cisco routers. In 2013, Cisco permitted other vendors to freely implement a limited version of EIGRP with some of its associated features such as High Availability (HA), while withholding other EIGRP features such as EIGRP stub, needed for DMVPN and large-scale campus deployment. Information needed for implementation was published with informational status as RFC 7868 in 2016, which did not advance to Internet Standards Track level, and allowed Cisco to retain control of the EIGRP protocol.

The Spanning Tree Protocol (STP) is a network protocol that builds a loop-free logical topology for Ethernet networks. The basic function of STP is to prevent bridge loops and the broadcast radiation that results from them. Spanning tree also allows a network design to include backup links providing fault tolerance if an active link fails.

A distance-vector routing protocol in data networks determines the best route for data packets based on distance. Distance-vector routing protocols measure the distance by the number of routers a packet has to pass; one router counts as one hop. Some distance-vector protocols also take into account network latency and other factors that influence traffic on a given route. To determine the best route across a network, routers using a distance-vector protocol exchange information with one another, usually routing tables plus hop counts for destination networks and possibly other traffic information. Distance-vector routing protocols also require that a router inform its neighbours of network topology changes periodically.

Link-state routing protocols are one of the two main classes of routing protocols used in packet switching networks for computer communications, the others being distance-vector routing protocols. Examples of link-state routing protocols include Open Shortest Path First (OSPF) and Intermediate System to Intermediate System (IS-IS).

Dial on Demand Routing (DDR) is a routing technique where a network connection to a remote site is established only when needed. In other words, if the router tries to send out data and the connection is off, then the router will automatically establish a connection, send the information, and close the connection when no more data needs to be sent. DDR is advantageous for companies that must pay per minute for a WAN setup, where a connection is always established. Constant connections can become needlessly expensive if the company does not require a constant internet connection.

<span class="mw-page-title-main">XORP</span> Internet Protocol routing software

XORP is an open-source Internet Protocol routing software suite originally designed at the International Computer Science Institute in Berkeley, California. The name is derived from eXtensible Open Router Platform. It supports OSPF, BGP, RIP, PIM, IGMP, OLSR.

Administrative distance (AD) or route preference is a number of arbitrary unit assigned to dynamic routes, static routes and directly-connected routes. The value is used in routers to rank routes from most preferred to least preferred. When multiple paths to the same destination are available in its routing table, the router uses the route with the lowest administrative distance.

A routing protocol specifies how routers communicate with each other to distribute information that enables them to select paths between nodes on a computer network. Routers perform the traffic directing functions on the Internet; data packets are forwarded through the networks of the internet from router to router until they reach their destination computer. Routing algorithms determine the specific choice of route. Each router has a prior knowledge only of networks attached to it directly. A routing protocol shares this information first among immediate neighbors, and then throughout the network. This way, routers gain knowledge of the topology of the network. The ability of routing protocols to dynamically adjust to changing conditions such as disabled connections and components and route data around obstructions is what gives the Internet its fault tolerance and high availability.

In network routing, the control plane is the part of the router architecture that is concerned with establishing the network topology, or the information in a routing table that defines what to do with incoming packets. Control plane functions, such as participating in routing protocols, run in the architectural control element. In most cases, the routing table contains a list of destination addresses and the outgoing interface(s) associated with each. Control plane logic also can identify certain packets to be discarded, as well as preferential treatment of certain packets for which a high quality of service is defined by such mechanisms as differentiated services.

Data center bridging (DCB) is a set of enhancements to the Ethernet local area network communication protocol for use in data center environments, in particular for use with clustering and storage area networks.

The Private Network-to-Network Interface (PNNI) is a link-state routing protocol used in Asynchronous Transfer Mode (ATM) networks. PNNI is similar to the Open Shortest Path First (OSPF) used for IP routing.

<span class="mw-page-title-main">Packet Tracer</span> Network simulation software

Packet Tracer is a cross-platform visual simulation tool designed by Cisco Systems that allows users to create network topologies and imitate modern computer networks. The software allows users to simulate the configuration of Cisco routers and switches using a simulated command line interface. Packet Tracer makes use of a drag and drop user interface, allowing users to add and remove simulated network devices as they see fit. The software is mainly focused towards Cisco Networking Academy students as an educational tool for helping them learn fundamental CCNA concepts. Previously students enrolled in a CCNA Academy program could freely download and use the tool free of charge for educational use.

IP routing is the application of routing methodologies to IP networks. This involves not only protocols and technologies but includes the policies of the worldwide organization and configuration of Internet infrastructure. In each IP network node, IP routing involves the determination of a suitable path for a network packet from a source to its destination in an IP network. The process uses static configuration rules or dynamically obtained from routing protocols to select specific packet forwarding methods to direct traffic to the next available intermediate network node one hop closer to the desired final destination, a total path potentially spanning multiple computer networks.

In a router, route redistribution allows a network that uses one routing protocol to route traffic dynamically based on information learned from another routing protocol.

References

  1. ↑ "Understanding the protocols underlying dynamic routing". CNET Networks, Inc. 24 July 2001. Retrieved 2014-11-26.
  2. ↑ CCNP 1 Advanced Routing Companion Guide. Indianapolis: Cisco Press. 2004. pp.  93f. ISBN   1-58713-135-8.
  3. ↑ "Networking Protocol Configurations". Cisco Systems. Archived from the original on 2007-05-27. Retrieved 2008-10-16.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.