Crack closure

Last updated February 10, 2023

Crack closure is a phenomenon in fatigue loading, where the opposing faces of a crack remain in contact even with an external load acting on the material. As the load is increased, a critical value will be reached at which time the crack becomes open. Crack closure occurs from the presence of material propping open the crack faces and can arise from many sources including plastic deformation or phase transformation during crack propagation, corrosion of crack surfaces, presence of fluids in the crack, or roughness at cracked surfaces.^[1]

Description

During cyclic loading, a crack will open and close causing the crack tip opening displacement (CTOD) to vary cyclically in phase with the applied force. If the loading cycle includes a period of negative force or stress ratio $R$ (i.e. $R<0$ ), the CTOD will remain equal to zero as the crack faces are pressed together. However, it was discovered that the CTOD can also be zero at other times even when the applied force is positive preventing the stress intensity factor reaching its minimum. Thus, the amplitude of the stress intensity factor range, also known as the crack tip driving force, is reduced relative to the case in which no closure occurs, thereby reducing the crack growth rate. The closure level increases with stress ratio and above approximately $R=0.7$ , the crack faces do not contact and closure does not typically occur.^[2]

The applied load will generate a stress intensity factor at the crack tip, $K$ producing a crack tip opening displacement, CTOD. Crack growth is generally a function of the stress intensity factor range, $\Delta K$ for an applied loading cycle and is

\Delta K=K_{\text{max}}-K_{\text{min}}

However, crack closure occurs when the fracture surfaces are in contact below the opening level stress intensity factor $K<K_{\text{op}}$ even though under positive load, allowing us to define an effective stress intensity range $\Delta K_{\text{eff}}$ as

\Delta K_{\text{eff}}=K_{\text{max}}-K_{\text{op}}

which is less than the nominal applied $\Delta K$ .

History

The phenomenon of crack closure was first discovered by Elber in 1970. He observed that a contact between the fracture surfaces could take place even during cyclic tensile loading.^[3]^[4] The crack closure effect helps explain a wide range of fatigue data, and is especially important in the understanding of the effect of stress ratio (less closure at higher stress ratio) and short cracks (less closure than long cracks for the same cyclic stress intensity).^[5]

Crack closure mechanisms

Plasticity-induced crack closure

The phenomenon of plasticity-induced crack closure is associated with the development of residual plastically deformed material on the flanks of an advancing fatigue crack.^[6]

The degree of plasticity at the crack tip is influenced by the level of material constraint. The two extreme cases are:

Under plane stress conditions, the piece of material in the plastic zone is elongated, which is mainly balanced by an out-of-the-plane flow of the material. Hence, the plasticity-induced crack closure under plane stress conditions can be expressed as a consequence of the stretched material behind the crack tip, which can be considered as a wedge that is inserted in the crack and reduces the cyclic plastic deformation at the crack tip and hence the fatigue crack growth rate.^[7]
Under plane strain conditions and constant load amplitudes, there is no plastic wedge at large distances behind the crack tip. However, the material in the plastic wake is plastically deformed. It is plastically sheared; this shearing induces a rotation of the original piece of material, and as a consequence, a local wedge is formed in the vicinity of the crack tip.^[8]

Phase-transformation-induced crack closure

Deformation-induced martensitic transformation in the stress field of the crack tip is another possible reason to cause crack closure. It was first studied by Pineau and Pelloux and Hornbogen in metastable austenitic stainless steels. These steels transform from the austenitic to the martensitic lattice structure under sufficiently high deformation, which leads to an increase of the material volume ahead of the crack tip. Therefore, compression stresses are likely to arise as the crack surfaces contact each other.^[9] This transformation-induced closure is strongly influenced by the size and geometry of the test specimen and of the fatigue crack.

Oxide-induced crack closure

Oxide-induced closure occurs where rapid corrosion occurs during crack propagation. It is caused when the base material at the fracture surface is exposed to gaseous and aqueous atmospheres and becomes oxidized.^[10] Although the oxidized layer is normally very thin, under continuous and repetitive deformation, the contaminated layer and the base material experience repetitive breaking, exposing even more of the base material, and thus produce even more oxides. The oxidized volume grows and is typically larger than the volume of the base material around the crack surfaces. As such, the volume of the oxides can be interpreted as a wedge inserted into the crack, reducing the effect stress intensity range. Experiments have shown that oxide-induced crack closure occurs at both room and elevated temperature, and the oxide build-up is more noticeable at low R-ratios and low (near-threshold) crack growth rates.^[11]

Roughness-induced crack closure

Roughness induced closure occurs with Mode II or in-plane shear type of loading, which is due to the misfit of the rough fracture surfaces of the crack’s upper and lower parts.^[10] Due to the anisotropy and heterogeneity in the micro structure, out-of-plane deformation occurs locally when Mode II loading is applied, and thus microscopic roughness of fatigue fracture surfaces is present. As a result, these mismatch wedges come into contact during the fatigue loading process, resulting in crack closure. The misfit in the fracture surfaces also takes place in the far field of the crack, which can be explained by the asymmetric displacement and rotation of material.^[12]

Roughness induced crack closure is justifiable or valid when the roughness of the surface is of same order as the crack opening displacement. It is influenced by such factors as grain size, loading history, material mechanical properties, load ratio and specimen type.

Related Research Articles

<span class="mw-page-title-main">Fracture</span> Split of materials or structures under stress

Fracture is the separation of an object or material into two or more pieces under the action of stress. The fracture of a solid usually occurs due to the development of certain displacement discontinuity surfaces within the solid. If a displacement develops perpendicular to the surface, it is called a normal tensile crack or simply a crack; if a displacement develops tangentially, it is called a shear crack, slip band or dislocation.

The field of strength of materials, also called mechanics of materials, typically refers to various methods of calculating the stresses and strains in structural members, such as beams, columns, and shafts. The methods employed to predict the response of a structure under loading and its susceptibility to various failure modes takes into account the properties of the materials such as its yield strength, ultimate strength, Young's modulus, and Poisson's ratio. In addition, the mechanical element's macroscopic properties such as its length, width, thickness, boundary constraints and abrupt changes in geometry such as holes are considered.

In materials science, fatigue is the initiation and propagation of cracks in a material due to cyclic loading. Once a fatigue crack has initiated, it grows a small amount with each loading cycle, typically producing striations on some parts of the fracture surface. The crack will continue to grow until it reaches a critical size, which occurs when the stress intensity factor of the crack exceeds the fracture toughness of the material, producing rapid propagation and typically complete fracture of the structure.

Fracture mechanics is the field of mechanics concerned with the study of the propagation of cracks in materials. It uses methods of analytical solid mechanics to calculate the driving force on a crack and those of experimental solid mechanics to characterize the material's resistance to fracture.

$<span class="mw-page-title-main">Stress intensity factor</span> Quantity in fracture mechanics; predicts stress intensity near a cracks tip$

In fracture mechanics, the stress intensity factor is used to predict the stress state near the tip of a crack or notch caused by a remote load or residual stresses. It is a theoretical construct usually applied to a homogeneous, linear elastic material and is useful for providing a failure criterion for brittle materials, and is a critical technique in the discipline of damage tolerance. The concept can also be applied to materials that exhibit small-scale yielding at a crack tip.

In materials science, fracture toughness is the critical stress intensity factor of a sharp crack where propagation of the crack suddenly becomes rapid and unlimited. A component's thickness affects the constraint conditions at the tip of a crack with thin components having plane stress conditions and thick components having plane strain conditions. Plane strain conditions give the lowest fracture toughness value which is a material property. The critical value of stress intensity factor in mode I loading measured under plane strain conditions is known as the plane strain fracture toughness, denoted $. When a test fails to meet the thickness and other test requirements that are in place to ensure plane strain conditions, the fracture toughness value produced is given the designation . Fracture toughness is a quantitative way of expressing a material's resistance to crack propagation and standard values for a given material are generally available.$

<span class="mw-page-title-main">Three-point flexural test</span> Standard procedure for measuring modulus of elasticity in bending

The three-point bending flexural test provides values for the modulus of elasticity in bending $, flexural stress, flexural strain and the flexural stress-strain response of the material. This test is performed on a universal testing machine with a three-point or four-point bend fixture. The main advantage of a three-point flexural test is the ease of the specimen preparation and testing. However, this method has also some disadvantages: the results of the testing method are sensitive to specimen and loading geometry and strain rate.$

Paris' law is a crack growth equation that gives the rate of growth of a fatigue crack. The stress intensity factor $characterises the load around a crack tip and the rate of crack growth is experimentally shown to be a function of the range of stress intensity seen in a loading cycle. The Paris equation is$

A fracture is any separation in a geologic formation, such as a joint or a fault that divides the rock into two or more pieces. A fracture will sometimes form a deep fissure or crevice in the rock. Fractures are commonly caused by stress exceeding the rock strength, causing the rock to lose cohesion along its weakest plane. Fractures can provide permeability for fluid movement, such as water or hydrocarbons. Highly fractured rocks can make good aquifers or hydrocarbon reservoirs, since they may possess both significant permeability and fracture porosity.

Material failure theory is an interdisciplinary field of materials science and solid mechanics which attempts to predict the conditions under which solid materials fail under the action of external loads. The failure of a material is usually classified into brittle failure (fracture) or ductile failure (yield). Depending on the conditions most materials can fail in a brittle or ductile manner or both. However, for most practical situations, a material may be classified as either brittle or ductile.

In fracture mechanics, the energy release rate, $, is the rate at which energy is transformed as a material undergoes fracture. Mathematically, the energy release rate is expressed as the decrease in total potential energy per increase in fracture surface area, and is thus expressed in terms of energy per unit area. Various energy balances can be constructed relating the energy released during fracture to the energy of the resulting new surface, as well as other dissipative processes such as plasticity and heat generation. The energy release rate is central to the field of fracture mechanics when solving problems and estimating material properties related to fracture and fatigue.$

Thermo-mechanical fatigue is the overlay of a cyclical mechanical loading, that leads to fatigue of a material, with a cyclical thermal loading. Thermo-mechanical fatigue is an important point that needs to be considered, when constructing turbine engines or gas turbines.

Polymer fracture is the study of the fracture surface of an already failed material to determine the method of crack formation and extension in polymers both fiber reinforced and otherwise. Failure in polymer components can occur at relatively low stress levels, far below the tensile strength because of four major reasons: long term stress or creep rupture, cyclic stresses or fatigue, the presence of structural flaws and stress-cracking agents. Formations of submicroscopic cracks in polymers under load have been studied by x ray scattering techniques and the main regularities of crack formation under different loading conditions have been analyzed. The low strength of polymers compared to theoretically predicted values are mainly due to the many microscopic imperfections found in the material. These defects namely dislocations, crystalline boundaries, amorphous interlayers and block structure can all lead to the non-uniform distribution of mechanical stress.

Crack tip opening displacement (CTOD) or $is the distance between the opposite faces of a crack tip at the 90° intercept position. The position behind the crack tip at which the distance is measured is arbitrary but commonly used is the point where two 45° lines, starting at the crack tip, intersect the crack faces. The parameter is used in fracture mechanics to characterize the loading on a crack and can be related to other crack tip loading parameters such as the stress intensity factor and the elastic-plastic J-integral.$

In materials science, toughening refers to the process of making a material more resistant to the propagation of cracks. When a crack propagates, the associated irreversible work in different materials classes is different. Thus, the most effective toughening mechanisms differ among different materials classes. The crack tip plasticity is important in toughening of metals and long-chain polymers. Ceramics have limited crack tip plasticity and primarily rely on different toughening mechanisms.

Solder fatigue is the mechanical degradation of solder due to deformation under cyclic loading. This can often occur at stress levels below the yield stress of solder as a result of repeated temperature fluctuations, mechanical vibrations, or mechanical loads. Techniques to evaluate solder fatigue behavior include finite element analysis and semi-analytical closed-form equations.

<span class="mw-page-title-main">Striation (fatigue)</span>

Striations are marks produced on the fracture surface that show the incremental growth of a fatigue crack. A striation marks the position of the crack tip at the time it was made. The term striation generally refers to ductile striations which are rounded bands on the fracture surface separated by depressions or fissures and can have the same appearance on both sides of the mating surfaces of the fatigue crack. Although some research has suggested that many loading cycles are required to form a single striation, it is now generally thought that each striation is the result of a single loading cycle.

A crack growth equation is used for calculating the size of a fatigue crack growing from cyclic loads. The growth of fatigue cracks can result in catastrophic failure, particularly in the case of aircraft. A crack growth equation can be used to ensure safety, both in the design phase and during operation, by predicting the size of cracks. In critical structure, loads can be recorded and used to predict the size of cracks to ensure maintenance or retirement occurs prior to any of the cracks failing.

Fastran is a computer program for calculating the rate of fatigue crack growth by combining crack growth equations and a simulation of the plasticity at the crack tip.

Slip bands or stretcher-strain marks are localized bands of plastic deformation in metals experiencing stresses. Formation of slip bands indicates a concentrated unidirectional slip on certain planes causing a stress concentration. Typically, slip bands induce surface steps and a stress concentration which can be a crack nucleation site. Slip bands extend until impinged by a boundary, and the generated stress from dislocation pile-up against that boundary will either stop or transmit the operating slip.

References

↑ Pippan, R.; Hohenwarter, A. (2017-02-01). "Fatigue crack closure: a review of the physical phenomena". Fatigue & Fracture of Engineering Materials & Structures. 40 (4): 471–495. doi:10.1111/ffe.12578. ISSN 8756-758X. PMC 5445565 . PMID 28616624.
↑ Zehnder, Alan (2012). Fracture mechanics. Springer Science+Business Media. p. 73. ISBN 9789400725942.
↑ Elber, Wolf (1970). "Fatigue crack closure under cyclic tension". Engineering Fracture Mechanics. 2: 37–45. doi:10.1016/0013-7944(70)90028-7.
↑ Elber, W. (1971). "The Significance of Fatigue Crack Closure". Damage Tolerance in Aircraft Structures. pp. 230–230–13. doi:10.1520/STP26680S. ISBN 978-0-8031-0031-2.
↑ Taylor, David (2007). Theory of Critical Distances - A New Perspective in Fracture Mechanics. Elsevier. p. 166. ISBN 978-0-08-044478-9.
↑ Pippan, R.; Kolednik, O.; Lang, M. (1994). "A Mechanism for Plasticity-Induced Crack Closure Under Plane Strain Conditions". Fatigue & Fracture of Engineering Materials & Structures. 17 (6): 721–726. doi:10.1111/j.1460-2695.1994.tb00269.x. ISSN 1460-2695.
↑ Ranganathan, N (1999), "Analysis of Fatigue Crack Growth in Terms of Crack Closure and Energy", Advances in Fatigue Crack Closure Measurement and Analysis: Second Volume, ASTM International, pp. 14–14–25, doi:10.1520/stp15748s, ISBN 9780803126114
↑ Antunes, Fernando; Branco, R.; Rodrigues, Dulce Maria (January 2011). "Plasticity Induced Crack Closure under Plane Strain Conditions". Key Engineering Materials. 465: 548–551. doi:10.4028/www.scientific.net/kem.465.548. ISSN 1662-9795.
↑ Mayer, H. R.; Stanzl-Tschegg, S. E.; Sawaki, Y.; Hühner, M.; Hornbogen, E. (2007-04-02). "Influence of transformation-induced crack closure on slow fatigue crack growth under variable amplitude loading". Fatigue & Fracture of Engineering Materials & Structures. 18 (9): 935–948. doi:10.1111/j.1460-2695.1995.tb00918.x.
1 2 Suresh, S.; Ritchie, R. O. (September 1982). "A geometric model for fatigue crack closure induced by fracture surface roughness". Metallurgical Transactions A. 13 (9): 1627–1631. Bibcode:1982MTA....13.1627S. doi:10.1007/bf02644803. ISSN 0360-2133.
↑ Suresh, S.; Zamiski, G. F.; Ritchie, D R. O. (August 1981). "Oxide-Induced Crack Closure: An Explanation for Near-Threshold Corrosion Fatigue Crack Growth Behavior". Metallurgical and Materials Transactions A. 12 (8): 1435–1443. doi:10.1007/bf02643688. ISSN 1073-5623.
↑ Pippan, R; Strobl, G; Kreuzer, H; Motz, C (September 2004). "Asymmetric crack wake plasticity – a reason for roughness induced crack closure". Acta Materialia. 52 (15): 4493–4502. doi:10.1016/j.actamat.2004.06.014. ISSN 1359-6454.

This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.

[:0-1] Pippan, R.; Hohenwarter, A. (2017-02-01). "Fatigue crack closure: a review of the physical phenomena". Fatigue & Fracture of Engineering Materials & Structures. 40 (4): 471–495. doi:10.1111/ffe.12578. ISSN 8756-758X. PMC 5445565 . PMID 28616624.

[2] Zehnder, Alan (2012). Fracture mechanics. Springer Science+Business Media. p. 73. ISBN 9789400725942.

[3] Elber, Wolf (1970). "Fatigue crack closure under cyclic tension". Engineering Fracture Mechanics. 2: 37–45. doi:10.1016/0013-7944(70)90028-7.

[4] Elber, W. (1971). "The Significance of Fatigue Crack Closure". Damage Tolerance in Aircraft Structures. pp. 230–230–13. doi:10.1520/STP26680S. ISBN 978-0-8031-0031-2.

[5] Taylor, David (2007). Theory of Critical Distances - A New Perspective in Fracture Mechanics. Elsevier. p. 166. ISBN 978-0-08-044478-9.

[6] Pippan, R.; Kolednik, O.; Lang, M. (1994). "A Mechanism for Plasticity-Induced Crack Closure Under Plane Strain Conditions". Fatigue & Fracture of Engineering Materials & Structures. 17 (6): 721–726. doi:10.1111/j.1460-2695.1994.tb00269.x. ISSN 1460-2695.

[7] Ranganathan, N (1999), "Analysis of Fatigue Crack Growth in Terms of Crack Closure and Energy", Advances in Fatigue Crack Closure Measurement and Analysis: Second Volume, ASTM International, pp. 14–14–25, doi:10.1520/stp15748s, ISBN 9780803126114

[8] Antunes, Fernando; Branco, R.; Rodrigues, Dulce Maria (January 2011). "Plasticity Induced Crack Closure under Plane Strain Conditions". Key Engineering Materials. 465: 548–551. doi:10.4028/www.scientific.net/kem.465.548. ISSN 1662-9795.

[9] Mayer, H. R.; Stanzl-Tschegg, S. E.; Sawaki, Y.; Hühner, M.; Hornbogen, E. (2007-04-02). "Influence of transformation-induced crack closure on slow fatigue crack growth under variable amplitude loading". Fatigue & Fracture of Engineering Materials & Structures. 18 (9): 935–948. doi:10.1111/j.1460-2695.1995.tb00918.x.

[:1-10] 1 2 Suresh, S.; Ritchie, R. O. (September 1982). "A geometric model for fatigue crack closure induced by fracture surface roughness". Metallurgical Transactions A. 13 (9): 1627–1631. Bibcode:1982MTA....13.1627S. doi:10.1007/bf02644803. ISSN 0360-2133.

[11] Suresh, S.; Zamiski, G. F.; Ritchie, D R. O. (August 1981). "Oxide-Induced Crack Closure: An Explanation for Near-Threshold Corrosion Fatigue Crack Growth Behavior". Metallurgical and Materials Transactions A. 12 (8): 1435–1443. doi:10.1007/bf02643688. ISSN 1073-5623.

[12] Pippan, R; Strobl, G; Kreuzer, H; Motz, C (September 2004). "Asymmetric crack wake plasticity – a reason for roughness induced crack closure". Acta Materialia. 52 (15): 4493–4502. doi:10.1016/j.actamat.2004.06.014. ISSN 1359-6454.

[1]

[2]

[3]

[4]

[5]

[6]

[7]

[8]

[9]

[10]

[11]

[12]