ET-Plus Guardrail

Last updated
ET-Plus Guardrail
InventorTexas A&M Transportation Institute
Inception1999 [2]
Current supplierTrinity Industries

The ET-Plus Guardrail system is a guardrail end terminal system manufactured by Trinity Highway Products, based in Dallas, Texas. The ET-Plus was designed at the Texas A&M Transportation Institute and built by Trinity. The end terminal cap absorbs the impact of a crash. The wooden posts break and the guardrail collapses. [3] The end terminal slides along, pushing the guardrail to the side. [4] However, in 2005, Trinity made changes to the ET-Plus without reporting the changes. [3] It was alleged that the Trinity design change caused it to malfunction. [5] A lawsuit under the False Claims Act filed in 2012 against Trinity stated that these changes were causing damages to cars and drivers. Tests have shown that the guardrails act the way they should. [3]

Contents

History

In the 1980s, Texas A&M Transportation Institute (TTI) had been conducting researches to improve guardrail safety for head-on collisions of guardrail ends. As a result, it developed the first model of energy-absorbing guardrail end terminals called ET-2000. The design used the "rail extrusion" process to allow the impact head with an extrusion throat to dissipate the impact energy by extruding the metal guardrail to bend it away from the vehicle to prevent it from sparring into the vehicle. ET-2000 crash testing that followed the guidelines in the United States was accepted by the Federal Highway Administration in 1989. The first recorded successful use was on Interstate 35 near Buda, Texas. [6]

In 1993, National Cooperative Highway Research Program published a report titled NCHRP Report 350, outlining an updated crash test and evaluation requirements to reflects the higher speeds and types of larger vehicles on the United States highways. ET-2000 was tested in accordance to the NCHRP Report 350 in 1995 and was accepted by the Federal Highway Administration. [6]

In 1999, TTI started developing ET-Plus based on the same extrusion throat design but with larger impact plate to accommodate more varieties of the vehicles and to reduce the weight of the impact head to lessen the crash severity. The design had 5-inch (13 cm) guide channels. [6] [7] A NCHRP Report 350 crash test of ET-Plus was conducted. Based on this specific test and an earlier full battery of tests of ET-2000 which shared the same extrusion throat design, the Federal Highway Administration approved ET-Plus to be used on highways in a letter dated January 18, 2000. TTI signed an exclusive licensing with Trinity Highway Products to be the manufacturer and seller of ET-Plus. [6]

TTI engineers continued to conduct researches and recommended to Trinity that by narrowing ET-Plus guide channels from 5 inches (13 cm) to 4 inches (10 cm), it could improve the alignment of the head on the rail. In 2005, Trinity proposed that it would use the 4-inch channel version for a new set of tests required for the new 31-inch (79 cm) guardrail height installations per NCHRP Report 350. The prototype of the 4-inch model was reviewed and approved by TTI. Trinity then used that model for the 2005 test battery. On September 2, 2005, the Federal Highway Administration approved ET-Plus to be used for the 31-inch installations. [6] However, it was later revealed that the Federal Highway Administration was not notified of the modification to 4-inch channel at the time of the approval. [7]

ET-Plus continued to be eligible for federal-aid reimbursement, until December 31, 2017, when ET-Plus did not comply to the new test criteria as outlined in the Manual for Assessing Safety Hardware (MASH). [8]

Controversies

ET-Plus with 4-inch channel ET-Plus channel width measurement.jpg
ET-Plus with 4-inch channel

On March 6, 2012, Joshua Harman, a Virginia guardrail engineer and a co-owner of a Trinity's competitor, was whistleblower in a federal suit which accused Trinity of failing to notify the Federal Highway Administration (FHWA) of a change of size of the end piece from five to four inches. [5] [7] The Federal Highway Administration requires that changes be reported immediately. [4] The change from five inches to four allegedly saved the company $2 per end terminal. [11] During a testimony, it was revealed that five crash tests were done in 2005 and 2006 showing the ET-Plus a failure by spearing a vehicle or flipping it. [11] Trinity argued that the tests were on an experimental system, and that the guardrails on the roads are safe. [4] [11] A federal jury found Trinity guilty of fraud by not reporting a change of one inch made to the ET-Plus end terminal. [12]

In October 2013, there was an allegation that Trinity produced the third version which slightly changed the 4-inch model was installed in Alabama highways in April 2013. It was alleged that the third version had some minor dimension changes including an expansion of welded-steel unit by 0.25 inches (0.64 cm), and those would be enough to prevent the 4-inch ET-Plus to malfunction. [13]

In November 2014, Trinity announced its plan to retest the 4-inch ET-Plus model and stopped the sale of the units until testing is completed. [4] In December 2014, an FHWA commissioned peer review of the study "Relative Comparison on NCHRT 350 Accepted W-Beam Guardrail End Terminals" was conducted by the University of Alabama at Birmingham. The reviewers found the information presented to be either questionable or invalid due to assumptions made on the report. [14] Tests were mandated by the FHWA. [15]

As of January 2015, 40 states had suspended new installations of ET-Plus terminals with 200,000 terminals had already been used on United States highways. [16] [3] States that have used the ET-Plus terminals are eligible for federal reimbursements. [5] The company did a series of eight crash tests which were released in February 2015. [16] [12] done by Southwest Research Institute in Texas. [14] The tests were conducted at the height of 31 inches to meet crash test criteria. The test results must be considered alongside data from actual crashes to come up with a comprehensive report. [17] Additionally, the FHWA collected measurements of more than 1,000 four-inch ET-Plus devices to address an allegation that there were the third version of ET-Plus units on the roadways. This data collection was to ensure that the 4-inch ET-Plus sets used in the tests were representative of actual terminals in use in many states. The result published on March 11, 2015 concluded that there was no systematic variation in the dimensions of the 4-inch ET-Plus units on the roadways and the ones used in the Southwest Research Institute tests. [10]

The U.S. Justice Department launched a criminal investigation into the use of the guardrail system in April 2015. [18] The federal cases accuse Trinity of making false and misleading statements about the ET-Plus system. [19]

In June 2015, a US district court jury verdict of $663 million was passed against Trinity Industries for defrauding the Federal Highway Administration. [20] [21] The original penalty of $175 million was tripled to $525 million, and an additional $8,250 was charged for each of the 16,771 false certification claims made by Trinity. Joshua Harmon, the whistleblower for the case, was awarded more than $16 million in legal fees and $2.3 million in expenses. [22] Harmon was also awarded $199 million, thirty percent of the $663 million judgement. [23] In September 2017, the United States Court of Appeals for the Fifth Circuit, in an opinion authored by Judge Patrick Higginbotham, reversed the finding of the district court and rendered judgement as a matter of law for Trinity. [24]

On November 5, 2015, a class action lawsuit was filed by counties in Missouri, including the city of St. Louis, Missouri, and the state’s transportation authority, against Trinity Industries and Trinity Highway Products alleging the that the ET-Plus guardrails were defective and dangerous. The lawsuit was settled for $56 million in 2022. [25] [26]

Related Research Articles

<span class="mw-page-title-main">Pothole</span> Road surface disruption type

A pothole is a depression in a road surface, usually asphalt pavement, where traffic has removed broken pieces of the pavement. It is usually the result of water in the underlying soil structure and traffic passing over the affected area. Water first weakens the underlying soil; traffic then fatigues and breaks the poorly supported asphalt surface in the affected area. Continued traffic action ejects both asphalt and the underlying soil material to create a hole in the pavement.

The Texas A&M Transportation Institute (TTI) in Bryan/College Station, Texas is a transportation research agency in the United States. The institute was created in 1950, primarily in response to the needs of the Texas Highway Department. TTI is a state agency and a member of the Texas A&M University System.

<span class="mw-page-title-main">Jersey barrier</span> Modular concrete or plastic barrier for separating vehicle traffic

A Jersey barrier, Jersey wall, or Jersey bump is a modular concrete or plastic barrier employed to separate lanes of traffic. It is designed to minimize vehicle damage in cases of incidental contact while still preventing vehicle crossovers resulting in a likely head-on collision. Jersey barriers are also used to reroute traffic and protect pedestrians and workers during highway construction. They are named after the U.S. state of New Jersey which first started using the barriers as separators between lanes of a highway in the 1950s.

<span class="mw-page-title-main">Rumble strip</span> Road safety feature

Rumble strips are a traffic calming feature to alert inattentive drivers of potential danger, by causing a tactile fuzzy vibration and audible rumbling transmitted through the wheels into the vehicle interior. A rumble strip is applied along the direction of travel following an edgeline or centerline, to alert drivers when they drift from their lane. Rumble strips may also be installed in a series across the direction of travel, to warn drivers of a stop or slowdown ahead, or of an approaching danger spot.

<i>Manual on Uniform Traffic Control Devices</i> National traffic control manual of the Federal Highway Administration

The Manual on Uniform Traffic Control Devices for Streets and Highways is a document issued by the Federal Highway Administration (FHWA) of the United States Department of Transportation (USDOT) to specify the standards by which traffic signs, road surface markings, and signals are designed, installed, and used. In the United States, all traffic control devices must legally conform to these standards. The manual is used by state and local agencies as well as private construction firms to ensure that the traffic control devices they use conform to the national standard. While some state agencies have developed their own sets of standards, including their own MUTCDs, these must substantially conform to the federal MUTCD.

<span class="mw-page-title-main">Clearview (typeface)</span> Humanist sans-serif typeface

Clearview, also known as Clearview Hwy, is the name of a humanist sans-serif typeface family for guide signs used on roads in the United States, Canada, Indonesia, the Philippines, Israel, Brazil and Sri Lanka. It was developed by independent researchers with the help of the Texas Transportation Institute and the Pennsylvania Transportation Institute, under the supervision of the Federal Highway Administration (FHWA). It was once expected to replace the FHWA typefaces in many applications, although newer studies of its effectiveness have called its benefits into question.

<span class="mw-page-title-main">Guard rail</span> Freestanding fixture meant to aid in pedestrian and vehicle safety

Guard, Guard rails, guardrails, railings or protective guarding, in general, are a boundary feature and may be a means to prevent or deter access to dangerous or off-limits areas while allowing light and visibility in a greater way than a fence. Common shapes are flat, rounded edge, and tubular in horizontal railings, whereas tetraform spear-headed or ball-finialled are most common in vertical railings around homes. Park and garden railings commonly in metalworking feature swirls, leaves, plate metal areas and/or motifs particularly on and beside gates.

The Midwest Roadside Safety Facility is a research organization in Lincoln, Nebraska that conducts automotive crash testing. MwRSF is operated by the University of Nebraska–Lincoln (NU) and researches highway design and safety with a particular emphasis on safety performance evaluations of roadside appurtenances. Since its establishment in 1974, the facility has evaluated existing barriers and frequently developed new design concepts and technologies for use on public roadways.

<span class="mw-page-title-main">Traffic barrier</span> Barrier installed within medians of and next to roads to prevent vehicle collisions

Traffic barriers keep vehicles within their roadway and prevent them from colliding with dangerous obstacles such as boulders, sign supports, trees, bridge abutments, buildings, walls, and large storm drains, or from traversing steep (non-recoverable) slopes or entering deep water. They are also installed within medians of divided highways to prevent errant vehicles from entering the opposing carriageway of traffic and help to reduce head-on collisions. Some of these barriers, designed to be struck from either side, are called median barriers. Traffic barriers can also be used to protect vulnerable areas like school yards, pedestrian zones, and fuel tanks from errant vehicles.

<span class="mw-page-title-main">Interstate 795 (North Carolina)</span> Highway in North Carolina

Interstate 795 (I-795) is a 25.49-mile (41.02 km) auxiliary Interstate Highway in the US state of North Carolina. It connects the city of Goldsboro to I-95 just south of Wilson, paralleling the northern portion of US Route 117 (US 117). The road runs a five-mile (8.0 km) concurrency with US 264 and I-587 in the last section of the route. It serves as a primary freeway spur for the city of Goldsboro to the Interstate Highway System, as well part of a major cargo route for the cities of Down East, which was a part of the impetus for its designation in 2007. Future plans call for the interstate to be further extended southward to meet I-40 near Faison.

Trinity Industries Inc. is an American industrial corporation that owns a variety of businesses which provide products and services to the industrial, energy, transportation and construction sectors.

<span class="mw-page-title-main">Federal Bridge Gross Weight Formula</span> Formula for estimating bridge weight limits

The Federal Bridge Gross Weight Formula, also known as Bridge Formula B or the Federal Bridge Formula, is a mathematical formula in use in the United States by truck drivers and Department of Transportation (DOT) officials to determine the appropriate maximum gross weight for a commercial motor vehicle (CMV) based on axle number and spacing. The formula is part of federal weight and size regulations regarding interstate commercial traffic. The formula is necessary to prevent heavy vehicles from damaging roads and bridges. CMVs are most often tractor-trailers or buses, but the formula is of most interest to truck drivers due to the heavy loads their vehicles often carry.

<span class="mw-page-title-main">Cable barrier</span>

A cable barrier, sometimes referred to as guard cable or wire rope safety barrier (WRSB), is a type of roadside or median safety traffic barrier/guard rail. It consists of steel wire ropes mounted on weak posts. As is the case with any roadside barrier, its primary purpose is to prevent a vehicle from leaving the traveled way and striking a fixed object or terrain feature that is less forgiving than itself. Also similar to most roadside barriers, cable barriers function by capturing and/or redirecting the errant vehicle.

<span class="mw-page-title-main">Roadway departure</span> Type of single-vehicle collision

A roadway departure is a type of incident that occurs when a vehicle leaves the roadway. Such incidents can lead to a single-vehicle collision.

<span class="mw-page-title-main">HAWK beacon</span> Traffic control device

A HAWK beacon is a traffic control device used to stop road traffic and allow pedestrians to cross safely. It is officially known as a pedestrian hybrid beacon. The purpose of a HAWK beacon is to allow protected pedestrian crossings, stopping vehicular traffic only as needed. The HAWK beacon is a type of traffic control alternative to traffic control signals and/or where an intersection does not meet traffic signal warrants.

<span class="mw-page-title-main">National Cooperative Highway Research Program</span>

The National Cooperative Highway Research Program (NCHRP) conducts research in problem areas that affect highway planning, design, construction, operation, and maintenance in the United States. Spearheaded by the Transportation Research Board (TRB), part of the National Academies of Sciences Engineering and Medicine, it is jointly supported by federal agencies, state departments of transportation (DOTs), and other nonprofit organizations.

Joshua Harman is an entrepreneur and activist. He is the co-founder of Selco Construction Services, as well as SPIG Industry LLC, a private Virginia-based company that installs guardrails. Harman is the whistleblower in the lawsuit against Trinity Industries Inc. He sued Trinity on behalf of the government under the qui tam provisions of the False Claims Act in 2012. In October 2014, the jury of the U.S. District Court in Marshall, Texas ruled that Trinity will pay $525 million, the largest whistleblower award won without the assistance of the US Justice Department. In June 2015, the judge awarded Harman over $199 million, or 30 percent of the final settlement of $663 million against Trinity Industries. This verdict was reversed by the Fifth Circuit Court of Appeals who ruled that there was no evidence that the government had in any way been defrauded.

The flail space model (FSM) is a model of how a car passenger moves in a vehicle that collides with a roadside feature such as a guardrail or a crash cushion. Its principal purpose is to assess the potential risk of harm to the hypothetical occupant as he or she impacts the interior of the passenger compartment and, ultimately, the efficacy of an experimental roadside feature undergoing full-scale vehicle crash testing.

<span class="mw-page-title-main">Offset T-intersection</span> Type of road intersections

An offset T-intersection is an at-grade road intersection where a conventional four leg intersection is split into two three-leg T-intersections to reduce the number of conflicts and improve traffic flow. Building the offset T-intersections as continuous green T-intersections, there is a single stop on the arterial road, only. A higher volume of through traffic on the cross road, or on unsignalized intersections, a rebuild to a conventional four-leg intersection may be adequate, also when the offset is a few feet only like staggered junctions causing slower traffic for a longer time on the arterial road.

Dean L. Sicking is an American inventor and safety researcher.

References

  1. ↑ Metal Beam Guardfence Transition and End Treatment Identification Guide (PDF). Texas Department of Transportation. 2016. p. 12. Retrieved 6 June 2024.
  2. ↑ Lindenberger, Michael A. (21 October 2014). "Following verdict, FHWA demands that Trinity Industries subject ET-Plus guardrails to further tests". Dallas News. Retrieved 1 June 2024.
  3. 1 2 3 4 Patrina Adger (January 4, 2015). "Texas Suspending Use of ET Plus Guardrails". KBTX. Archived from the original on August 9, 2015. Retrieved June 16, 2015.
  4. 1 2 3 4 Danielle Ivory; Aaron M. Kessler (November 12, 2014). "U.S. Accepts Trinity's Plan to Test Design of Guardrail". The New York Times. Retrieved June 16, 2015.
  5. 1 2 3 Ashley Halsey III (March 13, 2015). "Controversial guardrail performs correctly in federally mandated tests". The Washington Post. Retrieved June 16, 2015.
  6. 1 2 3 4 5 "ET Plus Development History" (PDF). Texas A&M Transportation Institute. 17 December 2014. Retrieved 3 June 2024.
  7. 1 2 3 In the United States Court of Appeals for the Fifth Circuit: No. 15-41172 (PDF). United States Court of Appeals for the Fifth Circuit. 29 September 2017. Retrieved 2 June 2024.
  8. ↑ "FHWA Review of ET-Plus: History of the ET-Plus". Federal Highway Administration. Retrieved 3 June 2024.
  9. ↑ "7 Investigates: Whistleblower claims dangerous change in guardrail design". KLTV. 25 September 2014. Retrieved 1 June 2024.
  10. 1 2 AASHTO – FHWA Task Force on ET-Plus 4” Dimensions (PDF). AASHTO & FHWA. 11 March 2015. pp. 2–9. Retrieved 1 June 2024.
  11. 1 2 3 Cindy Galli (December 11, 2014). "Virginia Sues Guardrail Maker for Fraud Ami Urgent Safety Tests". ABC News. Retrieved June 16, 2015.
  12. 1 2 Dave Jordan (March 13, 2015). "ET Plus Guardrails Pass All Eight Crash Tests". WSPA. Retrieved June 16, 2015.
  13. ↑ "Guardrails Seen as Killers Got Quiet Fix, Inventor Says" (PDF). Bloomberg. 12 December 2014. Retrieved 3 June 2024.
  14. 1 2 "FHWA Releases Results and Analysis of the Second Set of Crash Tests of ET-Plus Guardrail End Terminals". CE News. 2015-03-16. Archived from the original on 2016-01-30. Retrieved June 16, 2015.
  15. ↑ Nick Ochsner (March 25, 2015). "Guardrail testing complete, more tests possible". ABC 13. Archived from the original on July 18, 2015. Retrieved June 16, 2015.
  16. 1 2 Rudy Harper (February 9, 2015). "ET-Plus guardrails in Alabama being tested for safety". Fox. Archived from the original on July 2, 2015. Retrieved June 16, 2015.
  17. ↑ Dan Noyes (March 13, 2015). "Safety Officials Say Controversial Guardrail Passes Crash Tests". ABC 7. Retrieved June 16, 2015.
  18. ↑ Patrick G Lee (April 21, 2015). "U.S. Opens Criminal Probe Into Highway Guardrails Alleged to Turn Into Spears on Impact". Bloomberg Business. Retrieved June 16, 2015.
  19. ↑ Becky Oliver (April 29, 2015). "Two more lawsuits foiled over Trinity's E.T. Plus guardrail system". FOX 9. Retrieved June 16, 2015.
  20. ↑ Aaron M. Kessler; Danielle Ivory (June 9, 2015). "$663 Million in Penalties for Maker of Guardrail". New York Times. Retrieved June 16, 2015.
  21. ↑ Josh Smith (June 9, 2015). "VA Attorney General moving forward with lawsuit against guardrail company". WJHL. Retrieved June 16, 2015.[ permanent dead link ]
  22. ↑ "Federal judge hits guardrail company Trinity with $663 million penalty". The Roanoke Times. June 11, 2015. Retrieved June 16, 2015.[ permanent dead link ]
  23. ↑ William Joy (June 11, 2015). "Live 5 Investigates: Judge triples fine against guardrail company". Live 5 News. Retrieved June 16, 2015.
  24. ↑ Mark Curriden (October 2, 2017). "Fifth Circuit reverses $663 million judgment against DFW company". American City Business Journals. Retrieved October 12, 2017.
  25. ↑ "3 Months Ended Mar. 31, 2021 | Contingencies | Highway products litigation| State, county, and municipal actions". sec.gov. U.S. Securities and Exchange Commission . Retrieved 27 March 2024.
  26. ↑ Raymond, Nate (2022-06-01). "Trinity Industries reaches settlement worth $56 million in Missouri guardrail case". Reuters. Retrieved 2023-11-20.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.