The Leighton Radio Telescopes are 10.4 meter parabolic dish antennas designed by Robert B. Leighton in the 1970s, which were fabricated on the Caltech campus during the 1970s and 1980s. The telescope surfaces reached an accuracy of 10 microns RMS, allowing observations throughout the millimeter and submillimeter bands. In all, eight of these telescopes were made. They were used as the six elements of the Owens Valley Radio Observatory (OVRO) millimeter interferometer in California, and as single telescopes at the Caltech Submillimeter Observatory in Hawaii and the Raman Research Institute (RRI) at Bangalore, India. In the spring of 2005, the six Leighton telescopes in Owens Valley were moved [1] to a high mountain site in the White Mountains to form the core of the CARMA array of 25 telescopes. The CARMA array was decommissioned in 2015 at which time the Leighton telescopes were moved back to OVRO, where they are now being repurposed for different projects including the CO Mapping Array Pathfinder (COMAP) [2] (a 19 pixel imaging array), the Event Horizon Telescope (EHT), and various transient detection projects.
In 1973 Robert Leighton proposed to the NSF to build four 10.4 meter diameter parabolic dish radio antennas. Three of the antennas were to be used as a mm-wave interferometer to be sited at OVRO, and the fourth was to be used as a single submillimeter telescope at a high mountain site. The proposal was approved (AST 73-04908), and total funding was $477,700. [3]
The telescopes have an altazimuth fork mount. The azimuth axis is an inverted circular cone, the apex of which is supported by a thrust bearing. Cam-follower roller bearings mounted around the top of the base push against the top of the inverted cone to complete the azimuth axis constraint. There is a cable wrap for signal and power wiring which rides atop the azimuth thrust bearing. On the top of the cone is the azimuth platform, which supports two elevation bearings. The elevation tipping platform that supports the primary reflector is driven in elevation by a rotating ball-screw.
The azimuth platform is large enough to allow several people to work on it. It also houses a small sidecab room to the right of the right elevation bearing, which houses the Nasmyth focus radio receivers (typically SIS receivers). The sidecab also houses electronics for the axis encoders, LO & IF systems and tiltmeters along with the antenna control computer.
Three motors drive the telescope, two in azimuth and one in elevation. An offset in the drive voltage is maintained between the azimuth motors, in order to prevent backlash when driving the 1.74 meter diameter bull gear. The telescopes can slew at a rate of 40 degrees per minute.
The 10.4 meter primary mirror has a 0.4 focal ratio. The hyperboloid secondary mirror is 0.606 meters in diameter, and directs the light to either a Cassegrain focus or a Nasmyth focus, depending upon whether or not a tertiary mirror is present. The telescope has an effective focal ratio of 12.4 at the Cassegrain focus, which is located at the point of intersection of the azimuth and elevations axes. [4]
The primary mirror, usually called the dish, is composed of 84 panels which are hexagonal when projected onto the aperture plane (the RRI dish had 81 panels). Each panel is approximately 1.15 meters across. The panel that would have tiled the center of the dish is absent, providing the hole required for Cassegrain and Nasmyth foci. Panels near the edge of the dish are irregularly shaped, and in some cases larger than the nominal size, in order to tile the circular aperture without needing any very small panels. The mirror is 92% homologous, maintaining a nearly parabolic shape with only the focal point changing when the mirror deforms due to gravity as the telescope elevation changes. Deviations from homology are less than 17 microns RMS over the telescope's entire elevation range. These focus changes are compensated for by moving the secondary mirror laterally and along the optical axis.
A unique feature of the Leighton telescopes is that the primary is fabricated as a single 10.4 m diameter precision surface, rather than individually machined panels. The dish panels are made of a light weight (15 kg/m3) aluminum honeycomb material with vertical channels. To produce the reflector's parabolic shape, the panels were assembled atop the same steel tube space frame that will support the panels on the deployed telescope. The space frame was mounted on an air bearing surrounding a central mast. An arm extended from the central mast, which had a parabolic track on the bottom side. The parabolic track was shaped by a laser metrology system that made use of the fact that a parabola is the locus of points equidistant from the focal point and a directrix line. The directrix in this case was the upper side of the arm. After the parabolic track was created, a cutting tool moved along the track, and cut the honeycomb panels as the dish rotated on the air bearing. After the honeycomb panels were cut to the proper parabolic shape, an aluminum skin was applied to each panel, to provide the dish's reflecting surface. [5]
The space frame is fabricated from steel tubes less than 1.5 m long that have holes on each end for inserting dowel pins. The spacing between the holes is achieved with an accuracy of 10 microns. A single person can assemble the space frame on the air bearing in a few days. This concept was developed as part of a study of how a large telescope could be assembled by astronauts in space. The precision dowel pin joint also made it possible to perform accurate finite element analysis (FEA) using the computers available in the 1970s. This allowed iteration of the design tube cross-sections to improve the homology performance. During the machining of the surface, the space frame was supported kinematically on three primary points. The dowel pin joint space frame was designed to allow the dish, including panels, to be disassembled after fabrication into large sections (typically three) and transported to the observatory site, without significantly degrading the optical quality of the dish. The primary is placed on the tipping platform supported at the same three primary support points without introducing any new stresses. Six more points are fastened to the tipping platform to transfer the stiffness of the tipping platform to the space frame. Shims are used at the additional six attachment points to ensure that they do not stress the space frame while looking zenith. This is a critical part of the success of assembling the primary reflector onto the tipping platform and has been exploited when moving the telescopes to CARMA high mountain site and back to the valley.
All of the dishes, except for the one on the RRI telescope, were fabricated in the Synchrotron Building near the south-east corner of the Caltech campus; the building which was built to accommodate the equipment needed to polish the Hale Telescope 200 inch mirror nearly a half century earlier. The dish and mount for the RRI telescope were fabricated at National Aerospace Laboratories, with final assembly done in the RRI library.
The first three telescopes were deployed at the OVRO for testing as a millimeter wave interferometer. After the initial three element array was dedicated in 1985, three more antennas were added to the array to produce a six element interferometer. Fabrication of the second set of three OVRO antennas was overseen by David Woody, following Robert Leighton's retirement. Five of the six OVRO antennas were funded by the NSF, and the Kenneth and Eileen Norris Foundation paid for the sixth, which was dedicated in 1996. In 2005 these six telescopes were moved to the Cedar Flat in the Inyo Mountains of California, and added to the CARMA array. The CARMA array ceased operation in 2015, and the six Leighton telescopes were moved back to OVRO for storage. [6] One of these six antennas is now being used as the CO Mapping Array Pathfinder telescope.
The Leighton telescope with the most accurate (10 micron RMS) surface was shipped to Mauna Kea, Hawaii, and became the Caltech Submillimeter Observatory. This telescope was named the "Leighton Telescope" after the death of Robert Leighton in 1997. Unique among the Leighton telescopes, this unit had active control of the surface by means of heating elements added to the standoff pins supporting the surface panels. [7]
Another Leighton telescope was located in India at the Raman Research Institute. Although it followed the Leighton design fairly closely, it differs from all others because it was completely fabricated and assembled in India. It was also the only Leighton telescope which used prime focus receivers (in addition to receivers at the other foci). The telescope was placed atop a building which housed its IF system electronics and filter bank spectrometers. Operations began in 1988 with observations of SiO maser emission at 86 GHz from Mira-type variable stars. [8] In 1993 its surface accuracy was reported to be 120 microns RMS. [9] By 2009 the surface had degraded; holographic measurements at 12 GHz showed that the surface had a 350 micron RMS accuracy, but the surface still allowed observations at frequencies as high as 43 GHz with a 50% apperture efficiency. [10] The telescope was decommissioned around 2012.
In telecommunications and radar, a Cassegrain antenna is a parabolic antenna in which the feed antenna is mounted at or behind the surface of the concave main parabolic reflector dish and is aimed at a smaller convex secondary reflector suspended in front of the primary reflector. The beam of radio waves from the feed illuminates the secondary reflector, which reflects it back to the main reflector dish, which reflects it forward again to form the desired beam. The Cassegrain design is widely used in parabolic antennas, particularly in large antennas such as those in satellite ground stations, radio telescopes, and communication satellites.
A radio telescope is a specialized antenna and radio receiver used to detect radio waves from astronomical radio sources in the sky. Radio telescopes are the main observing instrument used in radio astronomy, which studies the radio frequency portion of the electromagnetic spectrum emitted by astronomical objects, just as optical telescopes are the main observing instrument used in traditional optical astronomy which studies the light wave portion of the spectrum coming from astronomical objects. Unlike optical telescopes, radio telescopes can be used in the daytime as well as at night.
A parabolic antenna is an antenna that uses a parabolic reflector, a curved surface with the cross-sectional shape of a parabola, to direct the radio waves. The most common form is shaped like a dish and is popularly called a dish antenna or parabolic dish. The main advantage of a parabolic antenna is that it has high directivity. It functions similarly to a searchlight or flashlight reflector to direct radio waves in a narrow beam, or receive radio waves from one particular direction only. Parabolic antennas have some of the highest gains, meaning that they can produce the narrowest beamwidths, of any antenna type. In order to achieve narrow beamwidths, the parabolic reflector must be much larger than the wavelength of the radio waves used, so parabolic antennas are used in the high frequency part of the radio spectrum, at UHF and microwave (SHF) frequencies, at which the wavelengths are small enough that conveniently sized reflectors can be used.
The Mount Wilson Observatory (MWO) is an astronomical observatory in Los Angeles County, California, United States. The MWO is located on Mount Wilson, a 5,710-foot (1,740-meter) peak in the San Gabriel Mountains near Pasadena, northeast of Los Angeles.
The Atacama Large Millimeter/submillimeter Array (ALMA) is an astronomical interferometer of 66 radio telescopes in the Atacama Desert of northern Chile, which observe electromagnetic radiation at millimeter and submillimeter wavelengths. The array has been constructed on the 5,000 m (16,000 ft) elevation Chajnantor plateau – near the Llano de Chajnantor Observatory and the Atacama Pathfinder Experiment. This location was chosen for its high elevation and low humidity, factors which are crucial to reduce noise and decrease signal attenuation due to Earth's atmosphere. ALMA provides insight on star birth during the early Stelliferous era and detailed imaging of local star and planet formation.
The James Clerk Maxwell Telescope (JCMT) is a submillimetre-wavelength radio telescope at Mauna Kea Observatory in Hawaii, US. The telescope is near the summit of Mauna Kea at 13,425 feet (4,092 m). Its primary mirror is 15 metres across: it is the largest single-dish telescope that operates in submillimetre wavelengths of the electromagnetic spectrum. Scientists use it to study the Solar System, interstellar dust and gas, and distant galaxies.
Robert Benjamin Leighton was a prominent American experimental physicist who spent his professional career at the California Institute of Technology (Caltech). His work over the years spanned solid state physics, cosmic ray physics, the beginnings of modern particle physics, solar physics, the planets, infrared astronomy, and millimeter- and submillimeter-wave astronomy. In the latter four fields, his pioneering work opened up entirely new areas of research that subsequently developed into vigorous scientific communities.
The Caltech Submillimeter Observatory (CSO) was a 10.4-meter (34 ft) diameter submillimeter wavelength telescope situated alongside the 15-meter (49 ft) James Clerk Maxwell Telescope (JCMT) at Mauna Kea Observatories. Beginning in 1986, it was engaged in submillimeter astronomy of the terahertz radiation band. The telescope closed on September 18, 2015.
The Submillimeter Array (SMA) consists of eight 6-meter (20 ft) diameter radio telescopes arranged as an interferometer for submillimeter wavelength observations. It is the first purpose-built submillimeter interferometer, constructed after successful interferometry experiments using the pre-existing 15-meter (49 ft) James Clerk Maxwell Telescope and 10.4-meter (34.1 ft) Caltech Submillimeter Observatory as an interferometer. All three of these observatories are located at Mauna Kea Observatory on Mauna Kea, Hawaii, and have been operated together as a ten element interferometer in the 230 and 345 GHz bands. The baseline lengths presently in use range from 16 to 508 meters. The radio frequencies accessible to this telescope range from 194–408 gigahertz (1.545–0.735 mm) which includes rotational transitions of dozens of molecular species as well as continuum emission from interstellar dust grains. Although the array is capable of operating both day and night, most of the observations take place at nighttime when the atmospheric phase stability is best.
Owens Valley Radio Observatory (OVRO) is a radio astronomy observatory located near Big Pine, California (US) in Owens Valley. It lies east of the Sierra Nevada, approximately 350 kilometers (220 mi) north of Los Angeles and 20 kilometers (12 mi) southeast of Bishop. It was established in 1956, and is owned and operated by the California Institute of Technology (Caltech). The Owens Valley Solar Array portion of the observatory has been operated by New Jersey Institute of Technology (NJIT) since 1997.
The Combined Array for Research in Millimeter-wave Astronomy (CARMA) was an astronomical instrument comprising 23 radio telescopes, dedicated in 2006. These telescopes formed an astronomical interferometer where all the signals are combined in a purpose-built computer to produce high-resolution astronomical images. The telescopes ceased operation in April 2015 and were relocated to the Owens Valley Radio Observatory for storage.
The Hat Creek Radio Observatory (HCRO) is operated by SRI International in the Western United States. The observatory is home to the Allen Telescope Array designed and owned by the SETI Institute in Mountain View, CA.
Llano de Chajnantor Observatory is the name for a group of astronomical observatories located at an altitude of over 4,800 m (15,700 ft) in the Atacama Desert of northern Chile. The site is in the Antofagasta Region approximately 50 kilometres (31 mi) east of the town of San Pedro de Atacama. The exceptionally arid climate of the area is inhospitable to humans, but creates an excellent location for millimeter, submillimeter, and mid-infrared astronomy. This is because water vapour absorbs and attenuates submillimetre radiation. Llano de Chajnantor is home to the largest and most expensive astronomical telescope project in the world, the Atacama Large Millimeter Array (ALMA). Llano de Chajnantor and the surrounding area has been designated as the Chajnantor Science Reserve by the government of Chile.
An astronomical interferometer or telescope array is a set of separate telescopes, mirror segments, or radio telescope antennas that work together as a single telescope to provide higher resolution images of astronomical objects such as stars, nebulas and galaxies by means of interferometry. The advantage of this technique is that it can theoretically produce images with the angular resolution of a huge telescope with an aperture equal to the separation, called baseline, between the component telescopes. The main drawback is that it does not collect as much light as the complete instrument's mirror. Thus it is mainly useful for fine resolution of more luminous astronomical objects, such as close binary stars. Another drawback is that the maximum angular size of a detectable emission source is limited by the minimum gap between detectors in the collector array.
The Owens Valley Solar Array (OVSA), also known as Expanded Owens Valley Solar Array (EOVSA), is an astronomical radio telescope array, located at Owens Valley Radio Observatory (OVRO), near Big Pine, California, with main interests in studying the physics of the Sun. The instruments of the observatory are designed and employed specifically for studying the activities and phenomena of our solar system's sun. Other solar dedicated instruments operated on the site include the Solar Radio Burst Locator (SRBL), the FASR Subsystem Testbed (FST), and the Korean SRBL (KSRBL). The OVSA is operated by the New Jersey Institute of Technology (NJIT), which also operates the Big Bear Solar Observatory.
The Yebes Observatory RT40m, or ARIESXXI, is a radio telescope which is part of the observatory at Yebes, Spain. It is a 40-metre Cassegrain–Nasmyth telescope.
The OVRO 40 meter Telescope is a radio telescope at the Owens Valley Radio Observatory near Big Pine, California, US. It is owned and operated by Caltech. The telescope is easily visible from the section of US highway 395 just north of Big Pine.
The Large Latin American Millimeter Array (LLAMA) is a single-dish 12 m Nasmyth optics antenna which is under construction in the Puna de Atacama desert in the Province of Salta, Argentina, next to the Qubic experiment. The primary mirror accuracy will allow observation from 40 GHz up to 900 GHz. After installation it will be able to join other similar instruments to perform Very Large Base Line Interferometry or to work in standalone mode. Financial support is provided by the Argentinian and Brazilian governments. The total cost of construction, around US$20 million, and operation as well as the telescope time use will be shared equally by the two countries. Construction planning started in July 2014 after the formal signature of an agreement between the main institutions involved.
The Crossed Dragone Telescope is an off-axis telescope design consisting of a parabolic primary mirror and a large concave secondary mirror arranged so that the focal plane is at right angles to the incoming light. In this configuration the polarization of light is preserved through the optics.
Thomas Gould Phillips was a British-born physicist, who worked primarily in the United States. He was a pioneer in the field of submillimeter astronomy, who both developed new instrumentation and made ground-breaking observations. He oversaw the construction of, and was the first and longest-serving director of the Caltech Submillimeter Observatory.