Line lock

Last updated December 31, 2023

A line lock is a device that allows the front brakes to lock independently of the rear brakes via a switch.^[1]^[2]^[3] The device is an electric solenoid that controls a valve which allows the brakes to be controlled individually. This allows the front brakes to be locked and the rear brakes to be open, and allows the driver to spin the rear wheels without wasting the rear brakes. This method is referred to as line lock and is popular among enthusiasts who like to do burnouts.

History

Drag racing is a motorsport often run using cars with manual transmissions. Manual transmissions allow drivers to control the amount of power transferred from the engine to the wheels by manipulating both clutch and throttle inputs, allowing vehicles to accelerate quickly without losing traction. However, launching a vehicle requires simultaneous gas pedal and clutch pedal inputs, preventing drivers from manipulating the brakes with their feet. Without brake input, drivers staging their vehicle at the starting line would roll if the clutch was slightly engaged. If the driver's vehicle rolled across the staging line before the start of a drag race, the driver could "red light" and would disqualify them from that race, nullifying the results or being declared DNF ("did not finish").^{[ citation needed ]} The line lock prevents vehicles from rolling by allowing the driver to control the clutch and accelerator using foot input and braking with the hand. In an automatic transmission vehicle, a line lock allows the engine to rev up to its peak power RPM and launch aggressively from the starting line.^{[ citation needed ]}

Usage

Line locks are often used for burnouts by fully locking the front wheels and then engaging the gas pedal and disengaging the clutch pedal. This makes the rear tires spin but keeps the car stationary.^[1]

Although less common, rolling burnouts can be achieved with modified line locks by proportionally increasing the front brake pressure and the throttle to keep the car at a steady speed. This makes the rear tires slip and spin faster than the front tires and burnout.^{[ citation needed ]}

Line locks can also be installed on the rear brake lines. When the line lock is activated, fluid pressure is prevented from being transferred to the rear, allowing the rear wheels to spin freely while the front brakes can be controlled with the brake pedal. This allows one to creep at varying speeds while maintaining a burnout. Achieving such a burnout requires manipulation of both throttle and brake inputs. The burnout is initiated by manipulating the clutch with the left foot and both the brake and gas pedal with the right foot. The brakes must be held while revving up the engine, then the clutch is released while continuing to hold the brakes. Once the rear tires start spinning, the left foot is used to control the brakes while the right foot continues to control the throttle. The only advantage for such a setup is the ability to maintain a burnout at relatively low wheel speeds, which reduces wear on the rear tires. This method can be used to increase tire temperature to provide better traction prior to a drag run, but it is also often used purely for show, such as in drifting exhibitions or simply for the personal enjoyment of the driver.^{[ citation needed ]} Many modern sport-oriented cars now offer optional line locks for drag and show purposes, such as the so-called "burnout mode" found on the 2015 Ford Mustang.^[4]

As a temporary parking brake

In most vehicles with rear drum brakes, two emergency brake/parking brake cables actuate the brake drums mechanically, but with much less force than is available through the primary hydraulic brake system. It is common for this type of system to work well when facing downhill but be unable to hold the vehicle stopped without using wheel chocks when facing up a steep hill. An improvement over stock parking brakes is useful for off-road vehicles such as tractors, tow trucks, 4x4's, construction vehicles or any drum brake vehicle on ice or steep terrain. Some manufactures use a transmission brake which locks the entire drivetrain.

In order to park by using the primary hydraulic brakes, a hand-operated valve is added to lock hydraulic pressure in the brake line.^[5] For parking using the brakes on all four wheels, two valves may be necessary. Any leakage at the brake cylinders will reduce pressure in the line and release the brakes. For this reason, line locks should only be used temporarily.^[6] Parking brakes using disc brakes do not have the same issues as drum brakes, but a vehicle needing parking brakes on all four wheels will still benefit from line locks.

Related Research Articles

An anti-lock braking system (ABS) is a safety anti-skid braking system used on aircraft and on land vehicles, such as cars, motorcycles, trucks, and buses. ABS operates by preventing the wheels from locking up during braking, thereby maintaining tractive contact with the road surface and allowing the driver to maintain more control over the vehicle.

A brake is a mechanical device that inhibits motion by absorbing energy from a moving system. It is used for slowing or stopping a moving vehicle, wheel, axle, or to prevent its motion, most often accomplished by means of friction.

Left-foot braking is the technique of using the left foot to operate the brake pedal in an automobile, leaving the right foot dedicated to the throttle pedal. It contrasts with the practice of using the left foot to operate the clutch pedal, leaving the right foot to share the duties of controlling both brake and gas pedals.

The handbrake turn is a driving technique used to deliberately slide a car sideways, either for the purpose of quickly negotiating a very tight bend, or for turning around well within the vehicle's own turning diameter.

An automatic transmission is a multi-speed transmission used in motor vehicles that does not require any input from the driver to change forward gears under normal driving conditions. Vehicles with internal combustion engines, unlike electric vehicles, require the engine to operate in a narrow range of rates of rotation, requiring a gearbox, operated manually or automatically, to drive the wheels over a wide range of speeds.

A traction control system (TCS), is typically a secondary function of the electronic stability control (ESC) on production motor vehicles, designed to prevent loss of traction of the driven road wheels. TCS is activated when throttle input and engine power and torque transfer are mismatched to the road surface conditions.

A manual transmission (MT), also known as manual gearbox, standard transmission, or stick shift, is a multi-speed motor vehicle transmission system, where gear changes require the driver to manually select the gears by operating a gear stick and clutch.

In mechanical or automotive engineering, a freewheel or overrunning clutch is a device in a transmission that disengages the driveshaft from the driven shaft when the driven shaft rotates faster than the driveshaft. An overdrive is sometimes mistakenly called a freewheel, but is otherwise unrelated.

A limited-slip differential (LSD) is a type of differential gear train that allows its two output shafts to rotate at different speeds but limits the maximum difference between the two shafts. Limited-slip differentials are often known by the generic trademark Positraction, a brand name owned by General Motors and originally used for its Chevrolet branded vehicles.

Drive by wire or DbW technology in the automotive industry is the use of electronic or electro-mechanical systems in place of mechanical linkages that control driving functions. The concept is similar to fly-by-wire in the aviation industry. Drive-by-wire may refer to just the propulsion of the vehicle through electronic throttle control, or it may refer to electronic control over propulsion as well as steering and braking, which separately are known as steer by wire and brake by wire, along with electronic control over other vehicle driving functions.

A burnout is the practice of keeping a vehicle stationary and spinning its wheels, the resultant friction causing the tires to heat up and smoke.

In road vehicles, the parking brake, also known as a handbrake or emergency brake (e-brake), is a mechanism used to keep the vehicle securely motionless when parked. Parking brakes often consist of a pulling mechanism attached to a cable which is connected to two wheel brakes. In most vehicles, the parking brake operates only on the rear wheels, which have reduced traction while braking. The mechanism may be a hand-operated lever, a straight pull handle located near the steering column, or a foot-operated pedal located with the other pedals.

A transmission control unit (TCU), also known as a transmission control module (TCM), or a gearbox control unit (GCU), is a type of automotive ECU that is used to control electronic automatic transmissions. Similar systems are used in conjunction with various semi-automatic transmissions, purely for clutch automation and actuation. A TCU in a modern automatic transmission generally uses sensors from the vehicle, as well as data provided by the engine control unit (ECU), to calculate how and when to change gears in the vehicle for optimum performance, fuel economy and shift quality.

Clutch control refers to the act of controlling the speed of a vehicle with a manual transmission by partially engaging the clutch plate, using the clutch pedal instead of the accelerator pedal. The purpose of a clutch is in part to allow such control; in particular, a clutch provides transfer of torque between shafts spinning at different speeds. In the extreme, clutch control is used in performance driving, such as starting from a dead stop with the engine producing maximum torque at high RPM.

The following outline is provided as an overview of and topical guide to automobiles:

A wheelspin occurs when the force delivered to the tire tread exceeds that of available tread-to-surface friction and one or more tires lose traction. This leads the wheels to "spin" and causes the driver to lose control over the tires that no longer have grip on the road surface. Wheelspin can also be done intentionally such as in drifting or doing a burnout.

All Wheel Control (AWC) is the brand name of a four-wheel drive (4WD) system developed by Mitsubishi Motors. The system was first incorporated in the 2001 Lancer Evolution VII. Subsequent developments have led to S-AWC (Super All Wheel Control), developed specifically for the new 2007 Lancer Evolution. The system is referred by the company as its unique 4-wheel drive technology umbrella, cultivated through its motor sports activities and long history in rallying spanning almost half a century.

An automobile skid is an automobile handling condition where one or more tires are slipping relative to the road, and the overall handling of the vehicle has been affected.

Car controls are the components in automobiles and other powered road vehicles, such as trucks and buses, used for driving and parking.

This glossary of automotive terms is a list of definitions of terms and concepts related to automobiles, including their parts, operation, and manufacture, as well as automotive engineering, auto repair, and the automotive industry in general. For more specific terminology regarding the design and classification of various automobile styles, see Glossary of automotive design; for terms related to transportation by road, see Glossary of road transport terms; for competitive auto racing, see Glossary of motorsport terms.

References

1 2 Kinnan, Rob (1 March 1996). "Install a Brake Line-Lock - How To - Hot Rod Magazine". Hot Rod Network. Archived from the original on 7 December 2022. Retrieved 4 December 2016.
↑ "Line Lock Install". MotorSports Digest. Archived from the original on 1 June 2010.
↑ Wunz, Tim. "Installation of Hurst Line Lock (Part #174 5000)". Tim's Hobbies. University of Arizona College of Pharmacy. Archived from the original on 13 September 2010.
↑ Ward, W. Christian Mental (3 May 2014). "The 2015 Mustang Burnout Switch and Forbidden Buttons". The Truth About Cars. Archived from the original on 28 July 2020. Retrieved 4 December 2016.
↑ "Roadless Gear. Brake Line Lock". Roadless Gear. Archived from the original on 25 October 2017. Retrieved 24 October 2017.
↑ "MICO Lever Lock: Operating Instructions" (PDF). MICO. 1 March 1998. Archived from the original (PDF) on 20 May 2021.

This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.

[hotrod-1] 1 2 Kinnan, Rob (1 March 1996). "Install a Brake Line-Lock - How To - Hot Rod Magazine". Hot Rod Network. Archived from the original on 7 December 2022. Retrieved 4 December 2016.

[isntall-2] "Line Lock Install". MotorSports Digest. Archived from the original on 1 June 2010.

[Hurst_line_lock-3] Wunz, Tim. "Installation of Hurst Line Lock (Part #174 5000)". Tim's Hobbies. University of Arizona College of Pharmacy. Archived from the original on 13 September 2010.

[4] Ward, W. Christian Mental (3 May 2014). "The 2015 Mustang Burnout Switch and Forbidden Buttons". The Truth About Cars. Archived from the original on 28 July 2020. Retrieved 4 December 2016.

[5] "Roadless Gear. Brake Line Lock". Roadless Gear. Archived from the original on 25 October 2017. Retrieved 24 October 2017.

[6] "MICO Lever Lock: Operating Instructions" (PDF). MICO. 1 March 1998. Archived from the original (PDF) on 20 May 2021.

[1]

[2]

[3]

[4]

[5]

[6]