Liquid carryover

Last updated

Liquid carryover [1] refers to the unintended transport of liquids such as water, hydrocarbon condensates, compressor oil or glycol in a natural gas, hydrogen, carbon dioxide or other industrial gas pipeline or process. [2] Ideally, only gas enters gas processing. [3]

Contents

Understanding pipeline composition at critical points is crucial to ensure optimal efficiency and safety.

Natural gas processing aims to deliver gas suitable for transmission systems without causing operational issues in downstream pipelines, compressors, or equipment. Ideally, all dry industrial gases remain "dry" during processing. However, due to fluid dynamics complexities, gas and liquid phases may not fully separate, leading to wet gas or two-phase flows. These can occur as mist flow (tiny liquid droplets) or stratified flow (a liquid stream along the pipe wall). These conditions can significantly impact gas processing facilities' operational safety, efficiency, and lifespan.

Challenges and risks

Liquid carryover is a major concern, responsible for roughly 60% of plant failures in natural gas processing. [4] Effective phase separation at the beginning of the processing train prevents hydrocarbons and other liquids from entering the gas treatment plant. Improper separation allows liquid carryover to contaminate the desulfurization stage, triggering foaming and fouling, leading to unplanned shutdowns and reduced gas flow. [5]

As the gas progresses through desulfurization and dehumidification, it comes into contact with significant processing liquids. Amine-based liquids used in desulfurization to remove hydrogen sulfide (H2S) and carbon dioxide (CO2) can carry over if not properly separated, contaminating the dehumidification stage. Dehumidification utilizes a liquid desiccant, such as monoethylene glycol (MEG) or triethylene glycol (TEG), to reduce gas moisture content and meet sales gas specifications. Carryover of glycol into this process can cause issues by blocking heat exchangers or disrupting temperature control. Notably, while glycol is a common component found during pipeline pigging analysis, there's currently no method to directly determine glycol carryover besides process cameras. [6]

The primary method for extracting natural gas liquids (NGLs) involves reducing gas temperature below its hydrocarbon dew point, separating the liquids. However, achieving temperature reduction through Joule-Thompson pressure reduction creates ideal conditions for sub-micron mist flow formation. This type of wet gas flow is particularly challenging to filter and requires specialized filtration systems. As the gas warms up, the liquids vaporize, saturating the vapor phase with respect to hydrocarbons. This can lead to liquid dropout as mist or stratified flows due to pressure and temperature drops during gas transmission.

Over time, solid and liquid accumulation at low points in the transmission system can lead to corrosion, potentially causing ruptures and failures at compressor stations.

Traditional monitoring techniques

Standards from the American Petroleum Institute (API) 14.1 and the International Organization for Standardization (ISO) EN10715 provide guidance for gas sampling for either laboratory or online analyzers of gas streams. They also offer guidelines for managing high-pressure gases to prevent liquid dropout in the sample system during pressure reduction from line pressure to atmospheric pressure. These standards aim to ensure a representative gas sample reaches the analyzer and prevent liquids from damaging it. However, wet gas or two-phase flows fall outside the scope of these standards, meaning gas analyzers can have significant errors and often miss liquid carryover events. [7]

Impact on operations

Liquid carryover's operational inefficiencies have both immediate and long-term consequences. Foaming, [8] requiring reduced gas flow and de-foaming chemicals, can occur. As a precaution, gas processing facilities may intentionally limit operational capacities, sacrificing optimal gas throughput. For gas processors, errors in hydrocarbon dew point and BTU determination can lead to lost revenue, pigging costs, and rectification or rebuild costs.

Transmission system

The presence of wet gas and liquid hold-up in pipelines significantly increases the risks of pipeline ruptures [9] and shortens the lifespan of pipeline assets. To mitigate these risks, operators must increase the frequency of pipeline pigging.

Power stations

As the gas reaches the power station, the likelihood of contamination rises due to various factors. These include:

Even though some power stations preheat the fuel gas, contamination with compressor oil or glycol (if not properly vaporized) can cause several maintenance issues. These include:

Liquefied natural gas (LNG) plants

Liquid carryover in incoming natural gas feed lines can also disrupt operations at LNG plants. Molecular sieves, used to dry the gas to extremely low moisture levels, become contaminated and lose efficiency when exposed to liquid hydrocarbons. In some cases, heavy hydrocarbons, believed to be compressor oil, have reached the LNG plant's "cold box," causing pressure differentials and shortening the operational period of the LNG train.

Calorific value and flow Measurements

During periods of mixed-phase flow (containing both gas and liquid), removing liquids from the gas sample being analyzed can lead to significant errors in determining the calorific value (BTU) of the gas. This makes it difficult to obtain an accurate picture of the overall fluid stream.

Gas analyzers can only report on the portion of the fluid they are presented with. This means that measurements made at custody transfer points, where gas ownership changes hands, are unreliable when two-phase flow is present. Process camera systems offer the highest level of sensitivity to both mist flow and stratified flow, providing operators with greater certainty about gas quality [10] and improving the accuracy of BTU or Wobbe Index measurements.

When liquid carryover is not specifically monitored, operators remain unaware of both continuous and occasional liquid events that significantly affect BTU calculations. This leads to inaccurate gas quality measurements.

Process camera systems have observed [11] that when liquid events occur as stratified flow, debris from the pipe wall (such as iron sulfide and scale) can accumulate on the bottom of the pipe. The high-velocity gas stream above the liquid layer removes lighter liquids, leaving behind a sludge that eventually dries into a stationary material. This material can reduce the pipe diameter.

If this scenario occurs at a custody transfer point, flow computers might use an incorrect pipe diameter in their calculations. Even with a properly calibrated flow meter, small amounts of debris (2-3mm) can cause a significant offset (0.2%) in the measurement. To ensure accurate fiscal measurements, these potential errors must be continuously monitored and factored into the uncertainty budget for all flow meters.

The Sarbanes-Oxley Act mandates that flow uncertainty budgets for fiscal flow measurements account for potential errors. [12] Unexpected liquids in dry gas systems can substantially increase the uncertainty budget associated with both flow and BTU measurements.

Related Research Articles

<span class="mw-page-title-main">Natural gas</span> Gaseous fossil fuel

Natural gas is a naturally occurring mixture of gaseous hydrocarbons consisting primarily of methane (95%) in addition to various smaller amounts of other higher alkanes. Traces of carbon dioxide, nitrogen, hydrogen sulfide, and helium are also usually present. Methane is colorless and odorless, and the second largest greenhouse gas contributor to global climate change after carbon dioxide. Because natural gas is odorless, odorizers such as mercaptan are commonly added to it for safety so that leaks can be readily detected.

<span class="mw-page-title-main">Pipeline</span> Pumping fluids or gas through pipes

A pipeline is a system of pipes for long-distance transportation of a liquid or gas, typically to a market area for consumption. The latest data from 2014 gives a total of slightly less than 2,175,000 miles (3,500,000 km) of pipeline in 120 countries around the world. The United States had 65%, Russia had 8%, and Canada had 3%, thus 76% of all pipeline were in these three countries. The main attribute to pollution from pipelines is caused by corrosion and leakage.

<span class="mw-page-title-main">Liquefied natural gas</span> Form of natural gas for easier storage and transport

Liquefied natural gas (LNG) is natural gas (predominantly methane, CH4, with some mixture of ethane, C2H6) that has been cooled down to liquid form for ease and safety of non-pressurized storage or transport. It takes up about 1/600th the volume of natural gas in the gaseous state at standard conditions for temperature and pressure.

Slug Catcher is the name of a unit in the gas refinery or petroleum industry in which slugs at the outlet of pipelines are collected or caught. A slug is a large quantity of a liquid that exists in a multi-phase pipeline.

A wet gas is any gas with a small amount of liquid present. The term "wet gas" has been used to describe a range of conditions varying from a humid gas which is gas saturated with liquid vapour to a multiphase flow with a 90% volume of gas. There has been some debate as to its actual definition, and there is currently no fully defined quantitative definition of a wet gas flow that is universally accepted.

<span class="mw-page-title-main">Turboexpander</span> Type of turbine for high-pressure gas

A turboexpander, also referred to as a turbo-expander or an expansion turbine, is a centrifugal or axial-flow turbine, through which a high-pressure gas is expanded to produce work that is often used to drive a compressor or generator.

A coalescer is a device which induces coalescence in a medium. They are primarily used to separate emulsions into their components via various processes, operating in reverse to an emulsifier.

Moisture analysis covers a variety of methods for measuring the moisture content in solids, liquids, or gases. For example, moisture is a common specification in commercial food production. There are many applications where trace moisture measurements are necessary for manufacturing and process quality assurance. Trace moisture in solids must be known in processes involving plastics, pharmaceuticals and heat treatment. Fields that require moisture measurement in gasses or liquids include hydrocarbon processing, pure semiconductor gases, bulk pure or mixed gases, dielectric gases such as those in transformers and power plants, and natural gas pipeline transport. Moisture content measurements can be reported in multiple units, such as: parts per million, pounds of water per million standard cubic feet of gas, mass of water vapor per unit volume or mass of water vapor per unit mass of dry gas.

<span class="mw-page-title-main">Natural-gas processing</span> Industrial processes designed to purify raw natural gas

Natural-gas processing is a range of industrial processes designed to purify raw natural gas by removing contaminants such as solids, water, carbon dioxide (CO2), hydrogen sulfide (H2S), mercury and higher molecular mass hydrocarbons (condensate) to produce pipeline quality dry natural gas for pipeline distribution and final use. Some of the substances which contaminate natural gas have economic value and are further processed or sold. Hydrocarbons that are liquid at ambient conditions: temperature and pressure (i.e., pentane and heavier) are called natural-gas condensate (sometimes also called natural gasoline or simply condensate).

The hydrocarbon dew point is the temperature at which the hydrocarbon components of any hydrocarbon-rich gas mixture, such as natural gas, will start to condense out of the gaseous phase. It is often also referred to as the HDP or the HCDP. The maximum temperature at which such condensation takes place is called the cricondentherm. The hydrocarbon dew point is a function of the gas composition as well as the pressure.

An oil production plant is a facility which processes production fluids from oil wells in order to separate out key components and prepare them for export. Typical oil well production fluids are a mixture of oil, gas and produced water. An oil production plant is distinct from an oil depot, which does not have processing facilities.

Onshore, when used in relation to hydrocarbons, refers to an oil, natural gas or condensate field that is under the land or to activities or operations carried out in relation to such a field.

<span class="mw-page-title-main">Custody transfer</span> Oil and gas industry term for transfer of physical substance from one operator to another

Custody Transfer in the oil and gas industry refers to the transactions involving transporting physical substance from one operator to another. This includes the transferring of raw and refined petroleum between tanks and railway tank cars; onto ships, and other transactions. Custody transfer in fluid measurement is defined as a metering point (location) where the fluid is being measured for sale from one party to another. During custody transfer, accuracy is of great importance to both the company delivering the material and the eventual recipient, when transferring a material.

Glycol dehydration is a liquid desiccant system for the removal of water from natural gas and natural gas liquids (NGL). It is the most common and economical means of water removal from these streams. Glycols typically seen in industry include triethylene glycol (TEG), diethylene glycol (DEG), ethylene glycol (MEG), and tetraethylene glycol (TREG). TEG is the most commonly used glycol in industry.

Black powder is an industry name for the abrasive, reactive particulate contamination present in all gas and hydrocarbon fluid transmission lines. Black powder ranges from light brown to black, and the mineral makeup varies per production field around the world.

Supersonic gas separation is a technology to remove one or several gaseous components out of a mixed gas. The process condensates the target components by cooling the gas through expansion in a Laval nozzle and then separates the condensates from the dried gas through an integrated cyclonic gas/liquid separator. The separator is only using a part of the field pressure as energy and has technical and commercial advantages when compared to commonly used conventional technologies.

<span class="mw-page-title-main">Bacton Gas Terminal</span> Gas terminal in Bacton

The Bacton Gas Terminal is a complex of six gas terminals within four sites located on the North Sea coast of North Norfolk in the United Kingdom. The sites are near Paston and between Bacton and Mundesley; the nearest town is North Walsham.

<span class="mw-page-title-main">Instrumentation in petrochemical industries</span>

Instrumentation is used to monitor and control the process plant in the oil, gas and petrochemical industries. Instrumentation ensures that the plant operates within defined parameters to produce materials of consistent quality and within the required specifications. It also ensures that the plant is operated safely and acts to correct out of tolerance operation and to automatically shut down the plant to prevent hazardous conditions from occurring. Instrumentation comprises sensor elements, signal transmitters, controllers, indicators and alarms, actuated valves, logic circuits and operator interfaces.

<span class="mw-page-title-main">Buzzard oil field</span>

The Buzzard Oil Field is an oil field located in the North Sea Blocks 19/10, 19/5a, 20/6 and 20/1s. It was discovered in 2001 by PanCanadian, and developed initially by PanCanadian's successor EnCana and then by Nexen. The oil field was initially operated and owned by Nexen which is now a subsidiary of China's CNOOC.

In the petroleum industry, allocation refers to practices of breaking down measures of quantities of extracted hydrocarbons across various contributing sources. Allocation aids the attribution of ownerships of hydrocarbons as each contributing element to a commingled flow or to a storage of petroleum may have a unique ownership. Contributing sources in this context are typically producing petroleum wells delivering flows of petroleum or flows of natural gas to a commingled flow or storage.

References

  1. ↑ Stockwell, Paul & Parker, Spencer (2024). "Errors In Hydrocarbon Dewpoint Can Lead To Large Losses For Gas Processing Plants" (PDF). Laurance Reid Gas Conditioning Conference. February 2024.
  2. ↑ D.Engel, H.Burns, S.Williams (2018), "Surfactant contaminants in feed gas streams to amine units - The phantom foaming agent", Gas Processing & LNG
  3. ↑ Philip Le Grange, Ben Spooner and Mike Sheilan (2017), “Trends in Tragedy – An in-depth study of Amine system failures, Ammoniaknowhow.com
  4. ↑ Philip Le Grange, Ben Spooner and Mike Sheilan (2017), “Trends in Tragedy – An in-depth study of Amine system failures, Ammoniaknowhow.com
  5. ↑ David B Engel and Scott N Williams (2020), "Contamination in gas compression: causes, effects, and solutions: Identifying and quantifying contaminants including solids, dissolved species, and liquids is essential in the design of a more reliable compression system", Digitalrefining.com
  6. ↑ P. Stockwell, “Liquid Carryover Detection to Improve Foam Management”, Laurence Reid Gas Conditioning Conference, Norman, OK, February 2020
  7. ↑ Richard Steven, Josh Kinney & Charlie Britton, Colorado Engineering Experiment Station Incorporated (2017) “Comparisons of Ultrasonic and Differential Pressure Meter Responses to Wet Natural Gas Flow, Norwegian Society for Oil and Gas Measurement, Global flow Workshop
  8. ↑ Saudi Aramco, Feed Gas Quality Challenges at Acid Gas Removal Plant, presented at GPA GCC Conference March 2018.
  9. ↑ National Transportation Safety Board, (2000) Natural Gas Pipeline Rupture and Fire Near Carlsbad, New Mexico August 19, 2000”, Pipeline accident report.
  10. ↑ Stockwell, Paul & Parker, Spencer (2024). "Errors In Hydrocarbon Dewpoint Can Lead To Large Losses For Gas Processing Plants" (PDF). Laurance Reid Gas Conditioning Conference. February 2024.
  11. ↑ Stockwell, Paul & Parker, Spencer (2024). "Errors In Hydrocarbon Dewpoint Can Lead To Large Losses For Gas Processing Plants" (PDF). Laurance Reid Gas Conditioning Conference. February 2024.
  12. ↑ Tim Nesler, EMS Pipeline Services (2005), Gas Measurement Has Key Role In Sarbanes-Oxley Law Compliance, Pipeline & Gas Journal - September 2005
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.