This article relies largely or entirely on a single source .(March 2011) |
Neck-through-body (commonly neck-thru or neck-through) is a method of electric guitar construction that combines the instrument's neck and core of its body into a single unit. This may be made of a solid piece of wood, or two or more laminated together. The strings, nut, fretboard, pickups and bridge are all mounted on this central core. Additional body side components (if any) that fill-out its shape are glued or mechanically attached to this central core. These are referred to as "wings". The construction technique is also used on electric bass guitars.
Neck-through-body construction is considerably more expensive than the traditional glued set-in neck and bolt-on neck style construction methods. However, it's less costly than the very rare and difficult "one-piece" fabrication of an entire instrument made from a single piece of material.
The first electric bass guitar, the solid-body "Audiovox 736" created by Paul Tutmarc circa 1937, had a neck-through construction.
"The Log", a prototype solid-body guitar built by Les Paul in 1941, can be considered as a forerunner of neck-through designed instrument. Les Paul built the model using a recycled 4x4 fence post as the neck and body core, and mounted the disassembled parts of an Epiphone and Gibson archtop guitar onto it.
The 1952-57 Harmony H44 had this construction feature.
In 1956 Rickenbacker was one of the first guitar manufacturers to use the modern variant of this technique, although this was originally restricted exclusively to semi-hollowbody guitars. [1]
The most important benefit for the player of a neck-thru guitar is the reduction of heel mass. The heel is the term used to describe the thickened area of the end of the neck and/or body where the neck is attached to the body. Body-neck connection area thickening is required for structural integrity. In violins this area's called the "button", "saddle" or "nose".
The area where the neck attaches to the body is naturally a weak zone. There's a lot of pressure exerted on the instrument due to the combined tension of all the strings pulling on the instrument between the tuners and the bridge. The neck-body connection area is weaker if you have to join a separate neck to a body. The screws (bolt-on) or glue (set-neck) used to connect the neck to the body requires significant area to be able to provide sound structural integrity to act against the string's tension and bond body to neck totally stably to ensure tuning stability of the instrument. Heel mass then becomes an obstacle when attempting to reach higher registers of the fretboard.
Neck-through construction allows easier access to higher frets because there is no need for a bulky heel as there is no neck-to-body connection. In such an instrument, the neck morphs into the body of such an instrument. When constructing a neck-through guitar the luthier can chamfer the neck-body transition area (which would be the heel) to a minimum, sometimes almost relieving the heel entirely. This allows easier, sometimes unhindered, access to the upper registers.
For players of rhythm or open chords alone, or players that do not reach up to the highest registers of the fretboard in lead or solo playing, this benefit is very minimal and will still necessitate increased cost of the production method.
However, some opine that a neck-thru guitar sounds different to a bolt-on construction instrument. This opinion asserts that neck-through construction provides greater sustain, richer overtones and increased tuning stability inherent in the design when compared to a bolt-on construction. But hard physical evidence for any of these is lacking, and the attribution of long sustain has been definitively contradicted by experimentation. [2]
Neck-through construction is significantly harder to mass-produce than bolt-on or set-in neck constructions. As such, guitars with this construction method tend to be more expensive than guitars made by other methods. This method of construction may be somewhat more common in basses than in guitars.
Repairs to the neck are usually expensive and tedious. In many cases, it is usually easier to remove the old neck completely, either by taking the wings off and putting an entirely new core in, or by converting the guitar to a bolt-on or set-neck by creating a heel and affixing the new neck to the core already in place, rather than to try to repair the neck itself.[ citation needed ] However, thanks to excellent stability and reaction to string tension and pressure, neck-through guitars tend to be more sturdy.[ citation needed ]
This structure is used by many companies, including Parker Guitars, BC Rich, Yamaha, Cort Guitars, Ibanez (primarily on basses), Jackson, Alembic, Schecter, Carvin, ESP Guitars, .strandberg*, Dean, Halo, Rickenbacker and many others.
Many configurations of the Gibson Firebird and Thunderbird are also built neck-through.
The construction method is also popular with independent guitar builders, who can typically devote more time to such a labour-intensive neck joint than a mass-producing company could.
The bass guitar, electric bass or simply bass is the lowest-pitched member of the guitar family. It is a plucked string instrument similar in appearance and construction to an electric or acoustic guitar, but with a longer neck and scale length. The bass guitar most commonly has four strings, though five- and six-stringed models are also relatively popular, and bass guitars with even more strings or courses have been built. Since the mid-1950s, the bass guitar has largely come to replace the double bass in popular music due to its lighter weight, the inclusion of frets in most models, and, most importantly, its design for electric amplification. This is also because the double bass is acoustically compromised for its range in that it is scaled down from the optimal size that would be appropriate for those low notes.
An electric guitar is a guitar that requires external electric sound amplification in order to be heard at typical performance volumes, unlike a standard acoustic guitar. It uses one or more pickups to convert the vibration of its strings into electrical signals, which ultimately are reproduced as sound by loudspeakers. The sound is sometimes shaped or electronically altered to achieve different timbres or tonal qualities via amplifier settings or knobs on the guitar. Often, this is done through the use of effects such as reverb, distortion and "overdrive"; the latter is considered to be a key element of electric blues guitar music and jazz, rock and heavy metal guitar playing. Designs also exist combining attributes of electric and acoustic guitars: the semi-acoustic and acoustic-electric guitars.
The guitar is a stringed musical instrument that is usually fretted and typically has six or twelve strings. It is usually held flat against the player's body and played by strumming or plucking the strings with the dominant hand, while simultaneously pressing selected strings against frets with the fingers of the opposite hand. A guitar pick may also be used to strike the strings. The sound of the guitar is projected either acoustically, by means of a resonant hollow chamber on the guitar, or amplified by an electronic pickup and an amplifier.
Rickenbacker International Corporation is a string instrument manufacturer based in Santa Ana, California. Rickenbacker is the first known maker of electric guitars, with a steel guitar in 1932, and produces a range of electric guitars and basses.
Steinberger is a series of distinctive electric guitars and bass guitars, designed and originally manufactured by Ned Steinberger. The name "Steinberger" can be used to refer to either the instruments themselves or the company that originally produced them. Although the name has been applied to a variety of instruments, it is primarily associated with a minimalist "headless" design of electric basses and guitars.
Modulus Graphite is an American manufacturer of musical instruments best known for building bass guitars with carbon fiber necks. The company, originally called Modulus Graphite, was founded in part by Geoff Gould, a bassist who also worked for an aerospace company in Palo Alto, California, and coworker Jerry Dorsch. When they split, Jerry started Graphite Guitar Systems in Washington state.
The following outline is provided as an overview of and topical guide to guitars:
A Bolt-on neck is a stringed musical instrument neck that attaches to the instrument body with either bolts or screws, as opposed to glue and joinery as with set-in neck joints.
The Gibson Thunderbird is an electric bass guitar made by Gibson and Epiphone.
The truss rod is a component of a guitar or other stringed instrument that stabilizes the lengthwise forward curvature of the neck. Usually, it is a steel bar or rod that runs through the inside of the neck, beneath the fingerboard. Some are non-adjustable, but most modern truss rods have a nut at one or both ends that adjusts its tension. The first truss rod patent was applied for by Thaddeus McHugh, an employee of the Gibson company in 1921, though the idea of a "truss rod" appears in patents as early as 1908.
A set-in neck is a traditional form of joining the neck of a stringed instrument with its body. This is typically done with a tightly fitted mortise-and-tenon or dovetail joint, secured with glue. Sonic qualities often attributed to this style of neck joint include a warm tone, long sustain, and a large surface area to transmit string vibration, leading to a "live" feeling instrument. But hard physical evidence for any of these is lacking, and the attribution of long sustain has been definitively contradicted by experimentation. In guitars it also often allows superior access to top frets closest to the body.
A solid-body musical instrument is a string instrument such as a guitar, bass or violin built without its normal sound box and relying on an electromagnetic pickup system to directly detect the vibrations of the strings; these instruments are usually plugged into an instrument amplifier and loudspeaker to be heard. Solid-body instruments are preferred in situations where acoustic feedback may otherwise be a problem and are inherently both less expensive to build and more rugged than acoustic electric instruments.
The neck is the part of certain string instruments that projects from the main body and is the base of the fingerboard, where the fingers are placed to stop the strings at different pitches. Guitars, banjos, ukuleles, lutes, the violin family, and the mandolin family are examples of instruments which have necks. Necks are also an integral part of certain woodwind instruments, such as the saxophone.
Set-through neck is a method of joining the neck and the body of guitar, effectively combining bolt-on, set-in and neck-through methods. It involves:
Tacoma Guitars was an American manufacturing company of musical instruments. It was founded in 1991 as a division of South Korean company Young Chang. Instruments were manufactured in Tacoma, Washington. The company and brand name were later acquired by the Fender Musical Instruments Corporation. The Tacoma plant closed, and production ceased, in 2008.
Electric guitar design is a type of industrial design where the looks and efficiency of the shape as well as the acoustical aspects of the guitar are important factors. In the past many guitars have been designed with various odd shapes as well as very practical and convenient solutions to improve the usability of the object.
The Rickenbacker 360/12 is the Rickenbacker company's 12-string variant of its 360 electric guitar model. Mainly known for producing "jangly" sounds, it was among the first electric 12-string guitars. The 360/12 was given worldwide attention when George Harrison used it on many Beatles recordings, introducing the distinctive new sound of this guitar on "I Call Your Name", which the band recorded in March 1964. In the late 1960s, the company made alternative models such as the Rickenbacker 370/12, which became the favored instrument of Roger McGuinn of the Byrds.
The Fender American Deluxe Series was a line of electric guitars and basses introduced by Fender in 1995 and discontinued in 2016. It was upgraded in 2004 and 2010 before being replaced by the American Elite series in 2016.
The Parker Fly was a model of electric guitar built by Parker Guitars. It was designed by Ken Parker and Larry Fishman, and first produced in 1993. The Fly is unique among electric guitars in the way it uses composite materials. It is notable for its light weight and resonance. It was also one of the first electric guitars to combine traditional magnetic pickups with piezoelectric pickups, allowing the guitarist to access both acoustic and electric tones. Production ended in 2016 and the company has not released a new model of any kind since.
The Fender Telecaster, colloquially known as the tele, is an electric guitar produced by Fender. Together with its sister model the Esquire, it was the world's first mass-produced, commercially successful solid-body electric guitar. Its simple yet effective design and revolutionary sound broke ground and set trends in electric guitar manufacturing and popular music. Many prominent rock musicians have been associated with the Telecaster for use in studio recording and live performances, most notably Bruce Springsteen, Prince, Luis Alberto Spinetta and Keith Richards.