Novel polymeric alloy

Last updated
Novel polymeric alloy
TypeNano-composite polymeric alloy
Main ingredientPolyolefin
Additional ingredientsPolyamides, compatibilizers, anti-toxidants, colorants
Density p0.96 g/cm3
Tensile strength(σt)19–32 MPa
Elastic limit/Yield 12%
Glass temperature 70°C
Melting point >200 °C
Linear expansion coefficient (α) 80 ppm°C
Source [1]

Novel polymeric alloy (NPA) is a polymeric alloy composed of polyolefin and thermoplastic engineering polymer with enhanced engineering properties. NPA was developed for use in geosynthetics. One of the first commercial NPA applications was in the manufacturer of polymeric strips used to form Neoloy® cellular confinement systems (geocells).

Contents

Novel polymeric alloy was developed as an alternative to high-density polyethylene (HDPE) in geosynthetics. Although HDPE is widely used due to its low cost, ease of manufacturing and flexibility, its relatively high creep, low tensile strength and sensitivity to elevated temperatures limit its use, for example, in long-term, critical geocell applications. [2]

Used in the manufacture of geosynthetics, such as cellular confinement system, novel polymeric alloy provides higher tensile strength and stiffness, and are more durable over dynamic loading and under elevated temperatures than those made from HDPE (Han, 2011). [3] The lifespan of NPA based geosynthetics, such as geocells, makes them suitable for long-term design in infrastructure, such as highways, railways, container yards and high retaining walls.

Production

Novel polymeric alloy (NPA) is compounded for geosynthetic applications, such as high-modulus geocells or geogrids. In geocell applications strips are co-extruded in multi-layer strips. Outer layers are a blend of polyolefins while the core layer is formed from a high performance polymer. The blend is generally immiscible (an alloy), where the high performance polymer is dispersed in a matrix formed by the polyolefins. Since polymer blends are basically unstable, they undergo stabilization during melt processing, at a nano-level combined with compatibilized material. [4]

The novel polymeric alloy core layer/s is made of a high performance polymer compound with a storage modulus of ≥1400 MPa at 23 °C, measured by Dynamic Mechanical Analysis (DMA) at a frequency of 1 Hz according to ASTM D4065; or an ultimate tensile strength of at least 30 MPa. The outer layers are usually made of a polyethylene or polypropylene polymer, with a blend or alloy with other polymers, fillers, additives, fibers and elastomers. The high performance alloys of polyamides, polyesters, and polyurethanes are combined with polypropylene, copolymers, block copolymers, blends and/or other combinations. [5]

Manufacture

While most polypropylene homopolymers are too brittle and most polypropylene copolymers are too soft, certain grades of polypropylene polymers are stiff enough for engineering purposes, yet soft enough so that a geosynthetic can be handled for installation. These polymers are modified, via proprietary treatment processes and the addition of additives such as nanoparticles to attain the required physical properties.

Unlike low crystalline polymers such as polypropylene, which require a post-extrusion processing such as orientation, cross-linking, and/or thermal annealing, higher crystalline polymers such as novel polymeric Alloy can be extruded as strips and welded in section without post-extrusion treatment. The sheet can be extruded into strips and welded, sown, or bonded together to form geosynthetic products. Such additives (stabilizers for polymers) may be selected from, among others, nucleating agents, fillers, fibers, hindered amine light stabilizers (HALS), antioxidants, UV light absorbers, and carbon black in the form of powders, fibers, or whiskers.

Properties

The polyolefin in the novel polymeric alloy polymer blend provides stress cracking resistance, hydrolytic resistance, very low temperature functionality and tear resistance, while the polyamide engineering polymer provides strength, stiffness, retention of mechanical strength at elevated temperatures, creep resistance and long-term dimensional stability. Novel polymeric alloy has a coefficient of thermal expansion CTE less than about 135 ppm/°C; resistance to acidic media greater than polyamide 6 resin and/or resistance to basic media greater than PET resin; resistance to hydrocarbons greater than that of HDPE; creep modulus of > 400 MPa at 25 °C at 20% of yield stress load for 60 minutes (ISO 899-1); and 1 percent secant flexural modulus > 700 MPa at 25 °C (ASTM D790). Novel polymeric alloy has a tensile strength in the range of 19.1 to 32 MPa with an elastic modulus of 440 to 820 MPa (at 2% strain). [1]

Applications

Novel polymeric alloy was developed for a high-modulus geosynthetics, including geocells, geogrids and geomembranes, which require higher strength, stiffness and durability. In a geocell application, the high modulus of Novel Polymeric Alloy means stiff and strong cell walls, which provide a very high elastic response to dynamic loading even after millions of cycles without permanent plastic deformation. [6] The strength and stiffness of novel polymeric alloy, as measured by tensile strength, long-term resistance to deformation, coefficient of thermal expansion (CTE) and performance at elevated temperatures (storage modulus), provides a performance lifespan previously available in geocell applications. This is a notable development in the geosynthetic / geocell industry, allowing the use of geocells for example, in structural reinforcement for flexible pavements, earth retention walls, and other heavy-duty geosynthetic applications, where long-term durability under heavy loading is critical (Leshchinsky, et al., 2009). At the same time, novel polymeric alloy properties enable the manufacture of lighter geocells which retain suitable engineering strength for moderate loading as typically found in slopes, channels and retaining wall applications.

See also

Related Research Articles

<span class="mw-page-title-main">Thermoplastic</span> Plastic that softens with heat and hardens on cooling

A thermoplastic, or thermosoftening plastic, is any plastic polymer material that becomes pliable or moldable at a certain elevated temperature and solidifies upon cooling.

<span class="mw-page-title-main">Polypropylene</span> Thermoplastic polymer

Polypropylene (PP), also known as polypropene, is a thermoplastic polymer used in a wide variety of applications. It is produced via chain-growth polymerization from the monomer propylene.

Amorphous poly alpha olefin is a commodity chemical used in multiple applications.

<span class="mw-page-title-main">Geosynthetics</span> Synthetic material used to stabilize terrain

Geosynthetics are synthetic products used to stabilize terrain. They are generally polymeric products used to solve civil engineering problems. This includes eight main product categories: geotextiles, geogrids, geonets, geomembranes, geosynthetic clay liners, geofoam, geocells and geocomposites. The polymeric nature of the products makes them suitable for use in the ground where high levels of durability are required. They can also be used in exposed applications. Geosynthetics are available in a wide range of forms and materials. These products have a wide range of applications and are currently used in many civil, geotechnical, transportation, geoenvironmental, hydraulic, and private development applications including roads, airfields, railroads, embankments, retaining structures, reservoirs, canals, dams, erosion control, sediment control, landfill liners, landfill covers, mining, aquaculture and agriculture.

Ultra-high-molecular-weight polyethylene is a subset of the thermoplastic polyethylene. Also known as high-modulus polyethylene (HMPE), it has extremely long chains, with a molecular mass usually between 3.5 and 7.5 million amu. The longer chain serves to transfer load more effectively to the polymer backbone by strengthening intermolecular interactions. This results in a very tough material, with the highest impact strength of any thermoplastic presently made.

A polyolefin is a type of polymer with the general formula (CH2CHR)n where R is an alkyl group. They are usually derived from a small set of simple olefins (alkenes). Dominant in a commercial sense are polyethylene and polypropylene. More specialized polyolefins include polyisobutylene and polymethylpentene. They are all colorless or white oils or solids. Many copolymers are known, such as polybutene, which derives from a mixture of different butene isomers. The name of each polyolefin indicates the olefin from which it is prepared; for example, polyethylene is derived from ethylene, and polymethylpentene is derived from 4-methyl-1-pentene. Polyolefins are not olefins themselves because the double bond of each olefin monomer is opened in order to form the polymer. Monomers having more than one double bond such as butadiene and isoprene yield polymers that contain double bonds (polybutadiene and polyisoprene) and are usually not considered polyolefins. Polyolefins are the foundations of many chemical industries.

<span class="mw-page-title-main">Polyphthalamide</span>

Polyphthalamide is a subset of thermoplastic synthetic resins in the polyamide (nylon) family defined as when 55% or more moles of the carboxylic acid portion of the repeating unit in the polymer chain is composed of a combination of terephthalic (TPA) and isophthalic (IPA) acids. The substitution of aliphatic diacids by aromatic diacids in the polymer backbone increases the melting point, glass transition temperature, chemical resistance and stiffness.

Zytel is a trademark owned by Celanese and used for a number of different high strength, abrasion and impact resistant thermoplastic polyamide formulations of the family more commonly known as nylon. The Zytel product line is based mostly on nylon 66, but also includes grades based on nylon 6 as a matrix, long chain nylons such as nylon 610, and copolymers including a transparent resin called Zytel 330. Resins based on polyphthalamides are branded 'Zytel HTN'. The Zytel product range takes advantage of the fact that nylons are one of the most compatible polymers with modifiers and so offers grades with varying degrees of fiberglass, from 13% to 60%,, rubber toughened resins, flame retarded grades. Nylon resins with mineral reinforcement are branded 'Minlon'.

<span class="mw-page-title-main">Hot-melt adhesive</span> Glue applied by heating

Hot-melt adhesive (HMA), also known as hot glue, is a form of thermoplastic adhesive that is commonly sold as solid cylindrical sticks of various diameters designed to be applied using a hot glue gun. The gun uses a continuous-duty heating element to melt the plastic glue, which the user pushes through the gun either with a mechanical trigger mechanism on the gun, or with direct finger pressure. The glue squeezed out of the heated nozzle is initially hot enough to burn and even blister skin. The glue is sticky when hot, and solidifies in a few seconds to one minute. Hot-melt adhesives can also be applied by dipping or spraying, and are popular with hobbyists and crafters both for affixing and as an inexpensive alternative to resin casting.

Thermoplastic olefin, thermoplastic polyolefin (TPO), or olefinic thermoplastic elastomers refer to polymer/filler blends usually consisting of some fraction of a thermoplastic, an elastomer or rubber, and usually a filler.

A geomembrane is very low permeability synthetic membrane liner or barrier used with any geotechnical engineering related material so as to control fluid migration in a human-made project, structure, or system. Geomembranes are made from relatively thin continuous polymeric sheets, but they can also be made from the impregnation of geotextiles with asphalt, elastomer or polymer sprays, or as multilayered bitumen geocomposites. Continuous polymer sheet geomembranes are, by far, the most common.

<span class="mw-page-title-main">Mechanically stabilized earth</span> Soil constructed with artificial reinforcing

Mechanically stabilized earth is soil constructed with artificial reinforcing. It can be used for retaining walls, bridge abutments, seawalls, and dikes. Although the basic principles of MSE have been used throughout history, MSE was developed in its current form in the 1960s. The reinforcing elements used can vary but include steel and geosynthetics.

<span class="mw-page-title-main">Landfill liner</span>

A landfill liner, or composite liner, is intended to be a low permeable barrier, which is laid down under engineered landfill sites. Until it deteriorates, the liner retards migration of leachate, and its toxic constituents, into underlying aquifers or nearby rivers, causing potentially irreversible contamination of the local waterway and its sediments.

<span class="mw-page-title-main">Cyclic olefin copolymer</span> Chemical compound

Cyclic olefin copolymer (COC) is an amorphous polymer made by several polymer manufacturers. COC is a relatively new class of polymers as compared to commodities such as polypropylene and polyethylene. This newer material is used in a wide variety of applications including packaging films, lenses, vials, displays, and medical devices.

Polybutylene (polybutene-1, poly(1-butene), PB-1) is a polyolefin or saturated polymer with the chemical formula (CH2CH(Et))n. Not be confused with polybutene, PB-1 is mainly used in piping.

<span class="mw-page-title-main">Filler (materials)</span> Particles added to improve its properties

Filler materials are particles added to resin or binders that can improve specific properties, make the product cheaper, or a mixture of both. The two largest segments for filler material use is elastomers and plastics. Worldwide, more than 53 million tons of fillers are used every year in application areas such as paper, plastics, rubber, paints, coatings, adhesives, and sealants. As such, fillers, produced by more than 700 companies, rank among the world's major raw materials and are contained in a variety of goods for daily consumer needs. The top filler materials used are ground calcium carbonate (GCC), precipitated calcium carbonate (PCC), kaolin, talc, and carbon black. Filler materials can affect the tensile strength, toughness, heat resistance, color, clarity, etc. A good example of this is the addition of talc to polypropylene. Most of the filler materials used in plastics are mineral or glass based filler materials. Particulates and fibers are the main subgroups of filler materials. Particulates are small particles of filler that are mixed in the matrix where size and aspect ratio are important. Fibers are small circular strands that can be very long and have very high aspect ratios.

<span class="mw-page-title-main">Cellular confinement</span> Confinement system used in construction and geotechnical engineering

Cellular confinement systems (CCS)—also known as geocells—are widely used in construction for erosion control, soil stabilization on flat ground and steep slopes, channel protection, and structural reinforcement for load support and earth retention. Typical cellular confinement systems are geosynthetics made with ultrasonically welded high-density polyethylene (HDPE) strips or novel polymeric alloy (NPA)—and expanded on-site to form a honeycomb-like structure—and filled with sand, soil, rock, gravel or concrete.

<span class="mw-page-title-main">Plastic film</span> Thin continuous polymeric material

Plastic film is a thin continuous polymeric material. Thicker plastic material is often called a "sheet". These thin plastic membranes are used to separate areas or volumes, to hold items, to act as barriers, or as printable surfaces.

<span class="mw-page-title-main">Acrylonitrile styrene acrylate</span> Chemical compound

Acrylonitrile styrene acrylate (ASA), also called acrylic styrene acrylonitrile, is an amorphous thermoplastic developed as an alternative to acrylonitrile butadiene styrene (ABS), that has improved weather resistance. It is an acrylate rubber-modified styrene acrylonitrile copolymer. It is used for general prototyping in 3D printing, where its UV resistance and mechanical properties make it an excellent material for use in fused filament fabrication printers, particularly for outdoor applications. ABS is also widely used in the automotive industry.

The Neoloy Geocell is a Cellular Confinement System (geocell) developed and manufactured by PRS Geo-Technologies Ltd. Geocells are extruded in ultrasonically welded strips. The folded strips are opened on-site to form a 3D honeycomb matrix, which is then filled with granular material. The 3D confinement system is used to stabilize soft subgrade soil and reinforce the subbase and base layers in flexible pavements. Cellular confinement is also used for soil protection and erosion control for slopes, including channels, retention walls, reservoirs and landfills.

References

  1. 1 2 Halahmi, I., Erez, O., Erez, A., (2009, 2010), High Performance Geosynthetic Article , US Patents 7,674,516 B2, 7,541,084 B2
  2. ↑ Leshchinsky, D. (2009) “Research and Innovation: Seismic Performance of Various Geocell Earth-retention Systems,” Geosysnthetics, No. 27, No. 4, 46-52
  3. ↑ Han, J., Pokharel, S. K., Yang, X. and Thakur, J. (2011). “Unpaved Roads: Tough Cell – Geosynthetic Reinforcement Shows Strong Promise.” Roads and Bridges. July, 49 (7), 40-43
  4. ↑ Halahmi, I., Erez, O., Erez, A., (2011), Process for Producing Compatibilized Polymer Blends, US Patent 8,026,309 B2
  5. ↑ Halahmi, I., Erez, O., Erez, A., (2012), Multi-layer Sandwich System for Geocells, US Patent 8,173,241 B2
  6. ↑ Pokharel, S. K., Han, J., Manandhar, C., Yang, X. M., Leshchinsky, D., Halahmi, I., and Parsons, R. L. (2011). “Accelerated Pavement Testing of Geocell-Reinforced Unpaved Roads over Weak Subgrade.” Journal of Transportation Research Board, the 10th International Conference on Low-Volume Roads, July 24–27, Lake Buena Vista, Florida, USA
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.