In computer networking, the Point-to-Point Protocol over ATM (PPPoA) is a layer 2 data-link protocol typically used to connect domestic broadband modems to ISPs via phone lines. It is used mainly with DOCSIS and DSL carriers, by encapsulating PPP frames in ATM AAL5. Point-to-Point Protocol over Asynchronous Transfer Mode (PPPoA) is specified by The Internet Engineering Task Force (IETF) in RFC 2364. [1]
It offers standard PPP features such as authentication, encryption, and compression. It also supports the encapsulation types: VC-MUX and LLC - see RFC 2364.
If it is used as the connection encapsulation method on an ATM based network it can reduce overhead significantly compared with PPPoEoA – by between 0 and ~3.125% for long packets, depending on the packet length and also on the choices of header options in PPPoEoA – see PPPoEoA protocol overheads. This is because it uses headers that are short so imposes minimal overheads, 2 bytes for PPP and 8 bytes for PPPoA (with the RFC2364 VC-MUX option) = 10 bytes. [2] [3] [4]
It also avoids the issues that PPPoE suffers from, related to sometimes needing to use an IP MTU of 1492 bytes or less, lower than the standard 1500 bytes.
The use of PPPoA over PPPoE is not geographically significant; rather, it varies by the provider's preference.
Configuration of a PPPoA requires PPP configuration and ATM configuration. These data are generally stored in a cable modem or DSL modem, and may or may not be visible to—or configurable by—an end-user.
PPP configuration generally includes: user credentials, user name and password, and is unique to each user.
ATM configuration includes:
ATM configuration can either be performed manually, or it may be hard-coded (or pre-set) into the firmware of a DSL modem provided by the user's ISP; it cannot be automatically negotiated.
{{cite journal}}: Cite journal requires |journal= (help)  | This computer networking article is a stub. You can help Wikipedia by expanding it. |
 | This Internet-related article is a stub. You can help Wikipedia by expanding it. |
 | This article related to telecommunications is a stub. You can help Wikipedia by expanding it. |
Asynchronous Transfer Mode (ATM) is a telecommunications standard defined by the American National Standards Institute and ITU-T for digital transmission of multiple types of traffic. ATM was developed to meet the needs of the Broadband Integrated Services Digital Network as defined in the late 1980s, and designed to integrate telecommunication networks. It can handle both traditional high-throughput data traffic and real-time, low-latency content such as telephony (voice) and video. ATM provides functionality that uses features of circuit switching and packet switching networks by using asynchronous time-division multiplexing.
Multiprotocol Label Switching (MPLS) is a routing technique in telecommunications networks that directs data from one node to the next based on labels rather than network addresses. Whereas network addresses identify endpoints the labels identify established paths between endpoints. MPLS can encapsulate packets of various network protocols, hence the multiprotocol component of the name. MPLS supports a range of access technologies, including T1/E1, ATM, Frame Relay, and DSL.
In computer networking, the maximum transmission unit (MTU) is the size of the largest protocol data unit (PDU) that can be communicated in a single network layer transaction. The MTU relates to, but is not identical to the maximum frame size that can be transported on the data link layer, e.g., Ethernet frame.
In computer networking, Point-to-Point Protocol (PPP) is a data link layer communication protocol between two routers directly without any host or any other networking in between. It can provide loop detection authentication, transmission encryption, and data compression.
A frame is a digital data transmission unit in computer networking and telecommunication. In packet switched systems, a frame is a simple container for a single network packet. In other telecommunications systems, a frame is a repeating structure supporting time-division multiplexing.
Password Authentication Protocol (PAP) is a password-based authentication protocol used by Point-to-Point Protocol (PPP) to validate users. PAP is specified in RFC 1334.
The Serial Line Internet Protocol (SLIP) is an encapsulation of the Internet Protocol designed to work over serial ports and router connections. It is documented in RFC 1055. On personal computers, SLIP has largely been replaced by the Point-to-Point Protocol (PPP), which is better engineered, has more features, and does not require its IP address configuration to be set before it is established. On microcontrollers, however, SLIP is still the preferred way of encapsulating IP packets, due to its very small overhead.
The Point-to-Point Protocol over Ethernet (PPPoE) is a network protocol for encapsulating Point-to-Point Protocol (PPP) frames inside Ethernet frames. It appeared in 1999, in the context of the boom of DSL as the solution for tunneling packets over the DSL connection to the ISP's IP network, and from there to the rest of the Internet. A 2005 networking book noted that "Most DSL providers use PPPoE, which provides authentication, encryption, and compression." Typical use of PPPoE involves leveraging the PPP facilities for authenticating the user with a username and password, predominately via the PAP protocol and less often via CHAP. Around 2000, PPPoE was also starting to become a replacement method for talking to a modem connected to a computer or router over an Ethernet LAN displacing the older method, which had been USB. This use-case, connecting routers to modems over Ethernet is still extremely common today.
In computer networking, Layer 2 Tunneling Protocol (L2TP) is a tunneling protocol used to support virtual private networks (VPNs) or as part of the delivery of services by ISPs. It uses encryption ('hiding') only for its own control messages, and does not provide any encryption or confidentiality of content by itself. Rather, it provides a tunnel for Layer 2, and the tunnel itself may be passed over a Layer 3 encryption protocol such as IPsec.
In computer networking and telecommunications, a pseudowire is an emulation of a point-to-point connection over a packet-switched network (PSN).
Throughput of a network can be measured using various tools available on different platforms. This page explains the theory behind what these tools set out to measure and the issues regarding these measurements.
PPPD is the Point-to-Point Protocol daemon which is used to manage network connections between two nodes on Unix-like operating systems. It is configured using command-line arguments and configuration files.
ATM Adaptation Layer 5 (AAL5) is an ATM adaptation layer used to send variable-length packets up to 65,535 octets in size across an Asynchronous Transfer Mode (ATM) network.
A broadband remote access server routes traffic to and from broadband remote access devices such as digital subscriber line access multiplexers (DSLAM) on an Internet service provider's (ISP) network. BRAS can also be referred to as a broadband network gateway or border network gateway (BNG).
In computer networking, Internet Protocol Control Protocol (IPCP) is a Network Control Protocol (NCP) for establishing and configuring Internet Protocol over a Point-to-Point Protocol link. IPCP is responsible for configuring the IP addresses as well as for enabling and disabling the IP protocol modules on both ends of the point-to-point link. IPCP uses the same packet exchange mechanism as the Link Control Protocol. IPCP packets may not be exchanged until PPP has reached the Network-Layer Protocol phase, and any IPCP packets received before this phase is reached should be silently discarded. IPCP has the NCP protocol code number 0x8021.
In computer networking, jumbo frames are Ethernet frames with more than 1500 bytes of payload, the limit set by the IEEE 802.3 standard. The payload limit for jumbo frames is variable: while 9000 bytes is the most commonly used limit, smaller and larger limits exist. Many Gigabit Ethernet switches and Gigabit Ethernet network interface controllers and some Fast Ethernet switches and Fast Ethernet network interface cards can support jumbo frames.
Virtual circuit multiplexing or VC-MUX is one of the two mechanisms for identifying the protocol carried in ATM Adaptation Layer 5 (AAL5) frames specified by RFC 2684, Multiprotocol Encapsulation over ATM.
Multiprotocol Encapsulation over ATM is specified in RFC 2684. It defines two mechanisms for identifying the protocol carried in ATM Adaptation Layer 5 (AAL5) frames. It replaces RFC 1483, a standard data link access protocol supported by DSL modems.
In computing and telecommunications, the payload is the part of transmitted data that is the actual intended message. Headers and metadata are sent only to enable payload delivery and are considered overhead.
Generic Stream Encapsulation, or GSE for short, is a Data link layer protocol defined by DVB. GSE provides means to carry packet oriented protocols such as IP on top of uni-directional physical layers such as DVB-S2, DVB-T2 and DVB-C2.