Providence (1866 steamboat)

Last updated
Providence (1867 steamboat) cropped.jpg
Providence
History
Name:Providence
Namesake: Providence, Rhode Island
Operator: Fall River Line
Route: New York-Newport-Fall River
Ordered: 1865
Builder: William H. Webb
Cost: $1,250,000
Launched: June 28, 1866
Completed: 1867
Acquired: 1867
Maiden voyage: June 1867
In service: 1867-1896
Fate: Scrapped, 1901
General characteristics
Type: Passenger sidewheel steamer
Tonnage: 2,962 gross, 2,064 net
Length: 362 ft
Beam: 48 ft 4 in, over guards 83 ft
Draft: 10 ft 3 in
Depth of hold: 16 ft 6 in
Installed power: 1 x 110-inch-cylinder simple beam steam engine delivering 2,900 IHP @ 19 RPM, 3 x boilers
Propulsion: 2 x 38 ft 8 in paddlewheels
Capacity: 840 to 1,200 passengers plus 40 railcars of freight

Providence was a large sidewheel steamer launched in 1866 by William H. Webb of New York for the Merchants Steamship Company. The first of Narragansett Bay's so-called "floating palaces", [1] the luxuriously outfitted Providence and her sister ship Bristol, each of which could carry up to 1,200 passengers, were installed with the largest engines then built in the United States, and were considered to be amongst the finest American-built vessels of their era.

Contents

Both ships would spend their entire careers steaming between New York and various destinations in and around Narragansett Bay, Rhode Island. Providence was eventually scrapped in 1901.

Development

Providence and Bristol owed their existence to a short-lived company known as the Merchants Steamship Company, which placed the initial order for the vessels with the Webb shipyard in about 1865. Merchants Steamship was an amalgamation of three existing Narragansett Bay shipping lines, the Commercial Line, Neptune Line and Stonington Line. The Company intended to run the two steamers between New York and Bristol, Rhode Island in competition with the Fall River Line, which ran a similar service from New York to Fall River, Massachusetts (both Lines then linking up to railway lines that continued on to Boston. [2]

Construction

Providence and Bristol were both fitted with massive 110-inch-cylinder (9 foot 2 inch) walking beam engines, the largest engines ever fitted to American vessels up to that time - larger even than the 100-inch-cylinder engine for the mammoth ironclad USS Dunderberg built at the Webb shipyard around the same time. [3] The engines, designed by Erasmus W. Smith, were supplied by the Etna Iron Works, which had only recently installed a lathe capable of boring such huge cylinders. The lathe itself was one of the two largest machine tools in the United States, the other being a planer installed by the same company. [4]

Work on both Bristol and Providence was delayed by a long strike, but Bristol was eventually launched in April 1866, and Providence on July 28 of the same year. [5] Between December 1865 and December 1866 however, the Merchants Steamship Company lost three of its existing ships, all of which were uninsured, thereby bankrupting the Company. Bristol and Providence remained in an uncompleted state at the shipyard until a new company, the Narragansett Steamship Company, which was partly owned by financier Jim Fisk, bought the new vessels in early 1867 and paid for their completion. [6]

Description

Interior of Providence, showing the main stairway and bulkhead in the rear saloon Providence main stairway.jpg
Interior of Providence, showing the main stairway and bulkhead in the rear saloon

When completed, Providence and Bristol were amongst the largest and most lavishly outfitted American vessels of their time. Each ship had 240 staterooms and over 300 berths, capable of accommodating 1,200 passengers, 840 of them in sleeping quarters. Their freight capacity was estimated at 40 railroad freight cars each. Their wooden hulls and paddle-boxes were strengthened with iron cross-bracings, while for safety they were installed with watertight compartments. The ships had gas lighting, and later on, steam heating and steam-powered steering. The decks, which were built of white oak, included an extra "gallery tier" deck from which passengers could view their surroundings. [7]

Contemporary American observers gushed over the size and sophistication of the ships, lauding them as "world renowned mammoth palace steamers", "so far in advance of the type of steamboats heretofore built that they were looked upon as marvels" and "the finest specimens of marine architecture of their day." [7] Bristol and Providence began a tradition of luxury travel on Narragansett Bay that would remain a popular attraction to travellers for the next fifty years. For a modest price, an ordinary working person could gain a glimpse of the opulent lifestyles of the wealthy just by taking a cruise on such a vessel. [8]

Service history

A lithograph of Providence passing her sister Bristol (foreground) at midnight on Long Island Sound The steamboats Bristol and Providence passing each other on Long Island Sound at midnight.jpg
A lithograph of Providence passing her sister Bristol (foreground) at midnight on Long Island Sound

Providence made her maiden voyage in June 1867, and for the next two years was to maintain the run from New York to Bristol, Rhode Island, as part of the Narragansett Steamship Company's Bristol Line. In 1869, the Narragansett Steamship Company merged with the Boston, Newport and New York Steamboat Company, and Providence and her sister ship Bristol thus joined the latter Company's Fall River Line. The two vessels began running from New York to Fall River, Massachusetts, with a stop at Newport, Rhode Island, while the service to Bristol was discontinued. Providence would subsequently maintain the New York-Fall River route to the end of her career. [3]

Customer service innovations

In the first weeks of Providence's service, Company President Jim Fisk would dress in an elegant "Admiral's" uniform to personally welcome aboard passengers, a practice which was soon discontinued. Two further innovations however were to prove more permanent. Fisk fitted his ship's crews with uniforms, which had an agreeable impact on customers, and he also employed a band of musicians on each vessel to entertain passengers on their journey, both innovations of which would henceforth become traditions on Fall River Line steamers. [9]

President Grant's "Peace Jubilee" voyage

In 1869, a "Peace Jubilee" was held in Boston, and U.S. President Ulysses S. Grant was invited to attend. After travelling to New York, the best accommodations of Providence were put at Grant's disposal for the next leg of his journey, which he accepted. [10]

Fisk hosted Grant on the voyage, while a number of other business leaders, including financier Jay Gould, also took passage in hopes of making Grant's acquaintance. Fisk went on to accompany Grant to the Boston Jubilee, and dressed once again in his flamboyant admiral's uniform, managed to upstage the U.S. President upon their entry together, from which he was to earn the nickname "Jubilee Jim". [10]

Collisions and other accidents

Over the course of her 29-year career, Providence was involved in several collisions and other accidents. The more significant of these are listed below.

On September 10, 1875, one of Providence's paddleboxes was damaged in a heavy storm off Point Judith, and the ship was forced to turn around and return slowly to Newport for repairs. On September 28, 1877, a schooner accidentally rammed Providence, the bowsprit penetrating through two staterooms to the inner saloon, but fortunately no-one was injured. On October 19, 1880, off Watch Hill, the port shaft of the eastbound Providence broke. A small propeller steamer named Albatross initially attempted a tow, but the larger City of Fitchburg then arrived on the scene and towed the stricken Providence back to Newport. Mechanical repairs took about two weeks. [11]

Providence's most serious accident occurred on June 22, 1887. At high tide, the steamer ran into the sand spit southeast of Hog Island, and could not be refloated for several weeks. The hull suffered considerable damage, requiring extended repairs, and the steamer City of Worcester (1881) was chartered to operate in her place while the repairs were effected. The following year, Providence was involved in another serious accident when she ran into and sank the steam yacht Adelaide. [11]

Final years

Providence was retired from regular service after the introduction of two new iron-hulled steamers, Puritan (1889) and Plymouth (1890), but was still used on occasion until Priscilla was added to the Fall River Line's fleet in 1894. Thereafter, Providence was only used when there were no other alternatives. Her last commercial voyages are believed to have occurred between December 1895 and early 1896, when she was called upon to operate for a few days when some of the regular steamers were temporarily out of commission. [12]

Providence's last years were spent tied up at Briggs Wharf, Newport. In the autumn of 1901, the vessel was sold for scrap and towed to Boston for dismantling. After the removal of her furnishings and machinery, Providence suffered the typical fate of wooden steamers of her time by being hauled onto a beach and burned in order to recover the remaining brass, copper, and other metal fittings. [12]

Footnotes

  1. "The Floating Palaces, 'Providence' and 'Bristol'", Newport Mercury, April 28, 1877, quoted in Covell, pp. 23–24.
  2. Covell 1933. pp. 10–11.
  3. 1 2 Covell 1933. p. 21.
  4. Swann, p. 20.
  5. "General City News", New York Times , July 28, 1866.
  6. Covell 1933. p. 11.
  7. 1 2 Covell 1933. pp. 21–22.
  8. "The Fall River Line and Other Steamers" Archived 2008-10-11 at the Wayback Machine , by Kay Davis, University of Virginia.
  9. Covell 1933. pp. 24–27.
  10. 1 2 Dayton, Fred Erving (1925): Steamboat Days, Frederick A. Stokes Company, New York, Chapter entitled "The Life and Times of Colonel James Fisk, Jr."; pp. 202-204, cited in Covell, p. 26.
  11. 1 2 Covell 1933. pp. 28–30.
  12. 1 2 Covell 1933. p. 30.

Related Research Articles

Steamship Type of steam-powered vessel

A steamship, often referred to as a steamer, is a type of steam-powered vessel, typically ocean-faring and seaworthy, that is propelled by one or more steam engines that typically move (turn) propellers or paddlewheels. The first steamships came into practical usage during the early 1800s; however, there were exceptions that came before. Steamships usually use the prefix designations of "PS" for paddle steamer or "SS" for screw steamer. As paddle steamers became less common, "SS" is assumed by many to stand for "steamship". Ships powered by internal combustion engines use a prefix such as "MV" for motor vessel, so it is not correct to use "SS" for most modern vessels.

Steamboat Smaller than a steamship; boat in which the primary method of marine propulsion is steam power

A steamboat is a boat that is propelled primarily by steam power, typically driving propellers or paddlewheels. Steamboats sometimes use the prefix designation SS, S.S. or S/S or PS ; however, these designations are most often used for steamships.

RMS <i>Segwun</i>

RMS Segwun is the oldest operating steam driven vessel in North America, built in 1887 as Nipissing to cruise the Muskoka Lakes in the Muskoka, Ontario, Canada, a resort area with many lakes and rivers. Early in the 20th century, Muskoka was poorly served by roads. Vacationers were transported to lodges, or private cottages, via a fleet of steamships. Segwun is one of only three ships in the world still carrying the status of Royal Mail Ship.

Old Colony Railroad

The Old Colony Railroad (OC) was a major railroad system, mainly covering southeastern Massachusetts and parts of Rhode Island, which operated from 1845 to 1893. Old Colony trains ran from Boston to points such as Plymouth, Fall River, New Bedford, Newport, Providence, Fitchburg, Lowell and Cape Cod. For many years the Old Colony Railroad Company also operated steamboat and ferry lines, including those of the Fall River Line with express train service from Boston to its wharf in Fall River where passengers boarded luxury liners to New York City. The company also briefly operated a railroad line on Martha's Vineyard, as well as the freight-only Union Freight Railroad in Boston. The OC was named after the "Old Colony", the nickname for the Plymouth Colony.

New York, Providence and Boston Railroad

The New York, Providence and Boston Railroad, normally called the Stonington Line, was a major part of the New York, New Haven and Hartford Railroad between New London, Connecticut and Providence, Rhode Island. It is now part of Amtrak's high-speed Northeast Corridor.

William H. Webb

William Henry Webb was a 19th-century New York City shipbuilder and philanthropist, who has been called America's first true naval architect.

India Point Park

India Point Park is a park in the Fox Point neighborhood of Providence, Rhode Island at the confluence of the Seekonk River and Providence River. The park takes its name from the maritime activity connecting Providence with the East and West Indies. The East Bay Bike Path begins at the eastern end of the park, and crosses over the Washington Bridge before heading to Watchemoket Square in East Providence and continuing on to Bristol and the Mount Hope Bridge. The park is also a part of the Washington–Rochambeau Revolutionary Route.

Fall River Line

The Fall River Line was a combination steamboat and railroad connection between New York City and Boston that operated between 1847 and 1937. It consisted of a railroad journey between Boston and Fall River, Massachusetts, where passengers would then board steamboats for the journey through Narragansett Bay and Long Island Sound to the line's own Hudson River dock in Manhattan. For many years, it was the preferred route to take for travel between the two major cities. The line was extremely popular, and its steamboats were some of the most advanced and luxurious of their day.

<i>River Queen</i> (steamboat)

The River Queen was a sidewheel steamer which became closely associated with President Abraham Lincoln and General Ulysses S. Grant while operating on the Potomac River, and was used for an unsuccessful peace conference during the last year of the American Civil War. Later it operated as a ferry serving the islands of Martha's Vineyard and Nantucket during the late 19th century. Late in its career, it returned to the Potomac as an excursion vessel, and in 1911, it was destroyed in a fire.

Morgan Iron Works

The Morgan Iron Works was a 19th-century manufacturing plant for marine steam engines located in New York City, United States. Founded as T. F. Secor & Co. in 1838, the plant was later taken over and renamed by one of its original investors, Charles Morgan.

Great Lakes passenger steamers

The history of commercial passenger shipping on the Great Lakes is long but uneven. It reached its zenith between the mid-19th century and the 1950s. As early as 1844, palace steamers carried passengers and cargo around the Great Lakes. By 1900, fleets of relatively luxurious passenger steamers plied the waters of the lower lakes, especially the major industrial centres of Chicago, Milwaukee, Detroit, Cleveland, Buffalo, and Toronto.

<i>Wilson G. Hunt</i> (sidewheeler)

Wilson G. Hunt was a steamboat that ran in the early days of steam navigation on Puget Sound and Sacramento, Fraser, and Columbia Rivers. She was generally known as the Hunt during her years of operation. She had a long career on the west coast of the United States and Canada, and played an important transportation role in the California Gold Rush; it also transported the Governor and the state legislature as the state capital of California moved from Benicia to Sacramento in 1854.

Baltimore Steam Packet Company Steamship company

The Baltimore Steam Packet Company, nicknamed the Old Bay Line, was an American steamship line from 1840 to 1962 that provided overnight steamboat service on the Chesapeake Bay, primarily between Baltimore, Maryland, and Norfolk, Virginia. Called a "packet" for the mail packets carried on government mail contracts, the term in the 19th century came to mean a steamer line operating on a regular, fixed daily schedule between two or more cities. When it closed in 1962 after 122 years of existence, it was the last surviving overnight steamship passenger service in the United States.

The Metropolitan Steamship Company was for 75 years one of the chief transportation links between New York City and Boston, Massachusetts. It was closely associated with the Whitney family until its acquisition by Charles W. Morse in 1906. Even after being merged into Eastern Steamship Lines, it was maintained as a distinct service, the Metropolitan Line, until 1941.

<i>Bristol</i> (1866 steamboat)

Bristol was a large sidewheel steamboat launched in 1866 by William H. Webb of New York for the Merchants Steamship Company. One of Narragansett Bay's so-called "floating palaces", the luxuriously outfitted Bristol and her sister ship Providence, each of which could carry up to 1,200 passengers, were installed with the largest engines then built in the United States, and were considered to be amongst the finest American-built vessels of their era.

Narragansett Pier Railroad

The Narragansett Pier Railroad was a railroad in southern Rhode Island, running 8 miles (13 km) from West Kingston to Narragansett Pier. It was built by the Hazard Family of Rhode Island to connect their textile mills in Peace Dale and Wakefield to the New York, Providence and Boston Railroad at Kingston Station as well as to ocean-going steamboats at Narragansett Pier. Passenger service ran on the line from 1876 to 1952; the line continued freight operation as a Class III railroad until 1981. Most of the right-of-way has been converted to the William C. O'Neill Bike Path.

The Delaware River Iron Ship Building and Engine Works, was a major late-19th-century American shipyard located on the Delaware River in Chester, Pennsylvania. It was founded by the industrialist John Roach and is often referred to by its parent company name of John Roach & Sons, or just known as the Roach shipyard. For the first fifteen years of its existence, the shipyard was by far the largest and most productive in the United States, building more tonnage of ships than its next two major competitors combined, in addition to being the U.S. Navy's largest contractor. The yard specialized in the production of large passenger freighters, but built every kind of vessel from warships to cargo ships, oil tankers, ferries, barges, tugs and yachts.

PS <i>Commonwealth</i> (1854)

Commonwealth was a large sidewheel steamboat built in 1854–55 for passenger service on Long Island Sound. The most celebrated Sound steamer of her day, Commonwealth was especially noted for the elegance and comfort of her passenger accommodations, which included gas lighting, steam heating, and an "enchantingly beautiful" domed roof in her upper saloon. Her stability of motion led her captain to describe Commonwealth as the finest rough weather steamboat ever built in the United States.

Two vessels of the Royal Navy have borne the name, HM galley Pigot. Both were acquired in 1778 during the American Revolutionary War, and both were lost that year; her crew destroyed the first to avoid her capture, and the Americans captured the second. Both were named for General Sir Robert Pigot, the general commanding the British Army at Newport, Rhode Island, during their service there.

<i>Senator</i> (1848 ship)

Senator was a wooden, side-wheel steamship built in New York in 1848. She was one of the first steamships on the California coast and arguably one of the most commercially successful, arriving in San Francisco at the height of the California gold rush. She was the first ocean-going steamer to sail up the Sacramento River to reach the new gold fields. After more purpose-built river steamers became available, Senator began a 26-year long career sailing between San Francisco and Southern California ports. Age and improving technology finally made the ship unsuitable for passenger service by 1882. Her machinery was removed and she was converted into a coal hulk. She ended her days in New Zealand, where she was broken up sometime around 1912.

References